GREENHOUSE 6'x8' ASSEMBLY INSTRUCTIONS. (Internal Dimensions) Overall Dimensions (Approx.) L 193 W 200 H cms 97.5" L 76" W 78.
|
|
- Nigel Ellis
- 5 years ago
- Views:
Transcription
1 ASSEMBLY INSTRUCTIONS GREENHOUSE 'x8' (Internal Dimensions) Overall Dimensions (Approx.) 7. L 9 W 00 H cms 97." L 7" W 78.8" H 0 IMPORTANT You must read these instructions carefully before you start to assemble this greenhouse. Please carry out the steps in the order set out in these instructions. Keep these instructions in a safe place for future reference.
2 SAFETY ADVICE We strongly recommend the use of work gloves during assembly as aluminium profiles may have sharp edges. Do not attempt to assemble the greenhouse in windy or wet conditions. Take special care not to touch overhead power cables with the aluminium profiles. Always wear shoes and safety goggles when working with extruded aluminium. Dispose of all plastic bags safely - keep them out of reach of small children. The greenhouse must be positioned and fixed on a flat level surface. Do not lean against or push the greenhouse during construction. Keep children away from the assembly area - the aluminium profiles may have sharp edges. Do not position your greenhouse in an area exposed to excessive wind. Do not attempt to assemble this greenhouse if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells. If using a step ladder ensure that you follow the manufacturers safety advice. If using power tools always follow the manufacturers instructions. Hot items such as recently used grills, blowtorches etc. must not be stored in the greenhouse. Ensure there are no hidden pipes or cables in the ground before inserting the ground stakes. GENERAL ADVICE This is a multi-part assembly. Allow at least 80 minutes to assemble from start to finish. Selecting a site - choose a sunny level position for your greenhouse away from overhanging trees. Select a large working area to construct the greenhouse. If you are fixing your greenhouse directly to a solid concrete base, please take into account the fixing brackets. See diagram and text (Area needed -.cm/0." Length x.9cm/8" Width including fixing brackets ) It is advisable to use a lubricant to ease connection between aluminium profiles and panels. Before starting installation the component parts should be checked and placed to the side, close at hand, in organized manner for easier identification when installing. Keep all small parts (screws etc.) in a bowl so they do not get lost. Note that the door is hinged on the right hand side and therefore opens to the right. You can opt to use the base brackets supplied to anchor your greenhouse to a concrete floor or you can use the optional base. We strongly advise you to keep the special white protective covers on the side panels and first line of roof panels until the greenhouse is fully assembled. You should however remove the white protective covers from the very top roof panels, as it will be very difficult to remove them afterwards. Keep roof clear of snow and leaves. CARE & MAINTENANCE TOOLS & EQUIPMENT REQUIRED When cleaning your greenhouse, use a mild detergent solution and rinse well with cold clean water. DO NOT use acetone, abrasive cleaners or other special detergents to clean the clear panels. When opening the greenhouse door do not pull the handle fiercely. Replacement parts - contact -877-MSTRGRO GENERAL ADVICE TOOLS & EQUIPMENT REQUIRED Silicone Sealant approved for polycarbonate Tape measure Work gloves Plastic or rubber mallet Lubricant( mild detergent solution and water) Phillips screwdriver Drill / metal drill bit Scissors Step ladder Level Large hammer If help is required seek professional advice within store. See over for contents
3 CONTENTS ITEM QTY. ITEM QTY. ITEM QTY.. X. 9 90mm 90mm 00mm 90mm x00mm. x7. 90mm.8 0 mm 0.7 Door handle hole 00x700mm. x7. 7mm 90mm x700mm 0mm mm. 8 0mm. 0mm. 90mm mm mm mm 8 0mm. 0A.9 00mm 0B 0C.9 7mm.7 0mm 9
4 Height: 00 H cm 78.8" H Width: 9 W cm 7" W Length: 7. L cm 97. L
5 Door Assembly Select profile IMPORTANT! You must ensure it is the correct way around. Slide the profile onto a square panel. Slide the rectangular panel (must be the panel with the door handle hole) onto the profile ensuring it has the interlocking slot at its bottom *. Repeat at all applicable steps. All panels must be locked before placing profiles. When necessary use a lubricant to ease connection between aluminium profiles and panels. SIDE SIDE UP & DOWN HANDLE HOLE MUST USE PANEL HINGE 7/0.7 * To interlock the two panels first bend the top panel towards you as shown (A), then push down fully (B). Bend back the top panel so it interlocks and is level with the bottom panel. A B
6 Lay the assembly on the floor and insert an angled bracket 9 only into the bottom of profile (A). Slide a -. profile onto the top and bottom of the door assembly (B), ensuring the angled bracket 9 slots into the bottom profile (see close up diagram). /. B /. B 7/0.7 /. 9 A /. 9 Slide another angled bracket 9 into the other end of the bottom profile -. (A). Slide the -0.7 profile on to the long side of the door (B) ensuring the angled bracket slots into the end of it. IMPORTANT! Do nothing more to the door at this stage. /0.7 9 A /.
7 7 Wall Assembly Stand the door up and on the hinge side, slide on a square panel. It will be easier if you open the hinge. 8 Slide on a rectangular panel and connect the two panels as shown earlier. 9 Slide on a corner profile -0.7 but 0 leave approximately.9 protruding at the top. The reason for this will become clear later. /0.7 Slide on another two panels ( and ) and then a profile Continue connecting the panels together until you have gone as far as shown on the diagram. Use profile -0.7 at the corner. Then attach panels and on the back wall of the greenhouse. /0.7 BACK /0.7 /0.7 IMPORTANT! Assemble in this direction
8 Slide on a vertical profile -. and fit another set of two panels. Fit horizontal profile -. as shown and slide on a top panel. Slide on another vertical profile -.. After completion of this step repeat the steps 9, 0, in order to reach the front of the greenhouse structure. Then procced to step. BACK VIEW /. /. /. At the door opening finish off the sides by sliding on the vertical profile /0.7 7
9 NOTE: You will require the assistance of another person to carry out the next stage of the assembly. You will be lifting the greenhouse and sliding six bottom rail profiles onto the bottom panels. There are three different length profiles to use so study the diagram below closely. Once all the bottom rail profiles are fitted, tap down all the vertical profiles using a rubber mallet. The vertical profiles /. should sit on the bottom rail profiles and the corner profiles sit on the floor. The front of the greenhouse does not get a bottom rail profile at this time. /. 0/.9 /. /. /0.7 0A/.9 /. Slide top panel on to the top of the door assembly. /0.7 0A/.9 Top of Door Insert four metal connector bars 0-.7 into the top of the door profiles as shown. Slide the twopart profile 8-. onto the hinged side of the top door panel ensuring it locates onto the metal bars. 0C/.7 /. /. 8/. 0C/.7 Slide a -. profile onto the top panel ensuring it locates with the inner metal connector. Place the other -. profile onto the outer metal connector 0C. 0C/.7 0C 0/0 8
10 7 Slide on the two front angled panels. Insert two profiles -. horizontally to join panels and together. /. 8 At the back wall of the greenhouse insert two metal connecting bars 0-.9 into the top section of profiles as shown. Slide down profiles either side of panel ensuring the angled end of the profiles are at the top and follow the same angle as the panel. 8 /0.8 0B/.9 0B /0.8 0B 9 Slide on the two back panels. Insert two profiles -. horizontally to join panels and together. BACK WALL /. /. /. 9
11 0 Roof Assembly Slide two profiles -.8 along the top long sides of the greenhouse. Insert a joining bar 0 between each pair to strengthen the joint. Panels may need aligning as you go. /.8 Slide four panels on to profiles as shown. Repeat for other side. 0 /.8 From inside the greenhouse and starting at one end, insert a profile -. to lock panels and together.then insert three -. profiles between the roof panels to lock them together. Finally finish off by inserting another profile -. at the corner. Repeat for the other side. /. /. Slide on two roof profiles -.8 on either side. You may need a stable step ladder at this stage.i nsert a joining bar 0 between each pair to strengthen the joint. /
12 Remove the white protective covers of these panels before fitting. Dispose of covers carefully. Decide where you wish to place the roof vent panel. Slide it in position together with three panels. Repeat the process on the other side of the roof using four panels. Note: At this point the panels are unsupported. This will be corrected during the next assembly steps. From inside the greenhouse insert profiles -. between the panels (and ). You should complete one side first and then the other. You may need a stable step ladder at this stage. /.
13 Insert part number to the right (door frame ) bottom that is connected to the wall panel frame. Do not connect part number to the inside of the door frame. Important insert it paralel to the 0 degrees angle wall as shown in drawing C. OUTSIDE A Now insert part number to the same door frame profil paralel to the panel insertion in its specific niche drawing C. Insert the other side of part to the bottom of C Look from the bottom. C Look from the bottom. 7 Slide profile -. from both sides of the front bottom /. (to panel number ). Slide it over part until the profile joint. A /. Look from the bottom. /. B /. Look from the bottom.
14 8 Insert part number into the frame door from above. 9 From outside the greenhouse insert roof profiles. at either end. IMPORTANT! you must slide the profile to the roof panel on the side and the part on the other side. /. 0 IMPORTANT! From this point on you will need someone else to assist you. Slide two profiles -.8 to the centre of the roof. Insert a joining bar 0 between each pair to strengthen the joint. /.8 0
15 OUTSIDE OUTSIDE From inside the greenhouse apply 00% silicone caulk/sealant that is compatible with polycarbonate to all the roof joint holes as ahown. Inject the 00% silicone generously until it oozes from the other holes. Use pairs of roof brackets to clamp each roof section where shown (A). Fix brackets in place using 0.7 nuts and bolts (B). Tighten with wrench. A B
16 Attach corner caps in all ten positions (front and back) using screws 8. You will need someone to help you with this step (one person inside, another outside). Do not over tighten. OUTSIDE 8 OPTION A Fixing to a solid base MPORTANT! The greenhouse must be firmly fixed to the ground. The best option is to fix to a solid base (i.e. concrete/blocks) using the fixing brackets supplied. Simply slide two brackets under the base profiles on all four sides and fix to the ground using suitable screws (minimum length "). For advice on suitable fixings seek professional help in store or local buiding official. Alternatively fix directly to the ground as below in step.. OUTSIDE BRACKET FIXING POSITIONS
17 Base construction Slot the base sections together as shown. IMPORTANT! ensure all the fixing holes are facing inward and closer to the top edge of the sections The shorter sections are used on the long sides and the longer sections are used on the short sides. Fix the sections together using 0. screws You must ensure the base is perfectly square and level before fixing it to the ground. With the help of another, test the greenhouse on the base before fixing it to the ground. Once you are happy with the position and squareness of the base, remove the greenhouse and fix the base to the ground using the ground stakes 0, one at each corner as shown. Check for hidden pipes and cables first! 0 CORNER 0 7 Fixing Greenhouse to Base Carefully reposition the greenhouse onto the base. From the inside, fit the brackets at positions shown on plan. Remove the two screws at these joints first, fit brackets and reattach the screws. Ensure the brackets hook over the bottom rim of the greenhouse. BRACKET FIXING POSITIONS Remember to remove all remaining white protective covers from panels. OUTSIDE Dispose of covers carefully. 9
GREENHOUSE EXTENSION 6 X4
ASSEMBLY INSTRUCTIONS GREENHOUSE EXTENSION 6 X Overall Dimensions (Approx.) 0 L x 93 W x 00 H cms 9" L x 76" W x 8.7" H 0 IMPORTANT You must read these instructions carefully before you start to assemble
More informationIMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)
ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions
More informationAssembly Instructions
Assembly Instructions Lean-To Greenhouse 129x68x165cm / 501/4"x263/4"x65" English_68467 Customer help and support line: 01302-380775 www.palramapplications.com EN IMPORTANT Please read these instructions
More informationPergola PR100N1. Assembly Instructions. Systems Trading Corporation Customer service: (877)
FABRIC Pergola PR00N Assembly Instructions Systems Trading Corporation Customer service: (8)82 82 of 20 Introduction Thank you for purchasing the Pergola PR00N. When properly assembled and maintained,
More informationGazebo GZ620H. Assembly Instructions. Systems Trading Corporation
Gazebo GZ20H Assembly Instructions Systems Trading Corporation 0 7th Avenue Suite 2809, New York, NY 02 Customer service: (877)782 82 Email: easygrow@stcaustin.com of 20 Introduction Thank you for purchasing
More informationGazebo GZ3584 Aluminum Composite Roof Panels
Gazebo GZ8 Aluminum Composite Roof Panels Assembly Instructions 7 9 2 9 8 0 2 2 Systems Trading Corporation Customer service: (877)782 82 Email: easygrow@stcaustin.com of Introduction Thank you for purchasing
More information11 x11 Pergola. Assembly Instructions. Paragon Group USA cm cm cm
FABRIC x Pergola Assembly Instructions 0cm 9 2cm 0cm 0 20cm Paragon Group USA Customer Service:(8) 82 82 Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the x Pergola. When
More informationGardman Lean-to Greenhouse Assembly Instructions
Page 1 Gardman Lean-to Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free
More informationGazebo GZ584. Assembly Instructions. Paragon Group USA. Customer Service:(877)
SU YESTE OL R P A Gazebo GZ NBRELL Assembly Instructions 0 9 max. 9 Paragon Group USA Customer Service:() Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the Gazebo GZ. When
More informationLAWN AND GARDEN GREENHOUSE
MODEL# OGAL-66 OGrow Walk-in 6' x ' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame Let'sGrow Together! Thank you for purchasing the OGROW greenhouse Follow the assembly and safety instructions
More informationLAWN AND GARDEN GREENHOUSE
MODELS# OG0AL8-BKE OGAL-8 OGrow Walk-in ' x 8' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame MANUAL VERSION # Grow r! e h t e g To Let's Thank you for purchasing the OGROW greenhouse Follow
More informationAssembly Instructions
BR FA I C x Pergola Assembly Instructions 7 7 9 0 Paragon Group USA Customer Service:(877) 78 8 Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the x Pergola. When properly
More informationGreenhouse Assembly Instructions
Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free 7 days a week on 0800
More informationEasy2Build TM. 6 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions
EasyBuild TM Smart Tech solutions 6 x 8 Easy-Grow Greenhouse Assembly Instructions 0 S tr uct ure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877)
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationSUPREME WALL GARDEN ASSEMBLY INSTRUCTIONS 24/08/16 www.hallsgreenhouses.com Please refer to website for the most up to date instructions. SAFETY WARNING 1. Always wear protective glasses, shoes, gloves
More informationGazebo JH734. Systems Trading Corporation. ~ Products Through Innovation
Gazebo JH734 Assembly Instructions Products Through Innovation Systems Trading Corporation 450 7th Avenue Suite 2809, New York, NY 10123 Customer service: (877)782 4482. Introduction Thank you for purchasing
More informationGROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02
GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.
More informationINFINITE RANGE - HINGE DOOR
INFINITE RANGE - HINGE DOOR HINGE DOOR + 1 SIDE RETURN PANEL (CORNER) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before moving
More informationConstable Oak Extension Dining Table
Constable Oak Extension Dining Table Assembly Instructions - Please keep for future reference 176/0325 Dimensions Width - 160/ 200cm Depth - 90cm Height - 75cm Important - Please read these instructions
More informationAssembly Instructions Please keep for future reference Inspire 40
Assembly Instructions Please keep for future reference Inspire 40 Version 3 : 28/07/2014 Important - Please read these instructions fully before starting assembly ALR2902 Safety and Care Advice Important
More informationINFINITE RANGE - CENTRE FOLDING DOOR
INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR ONLY ( RECESS) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationEasy2Build TM. 8 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions
EasyBuild TM Smart Tech solutions 8 x 8 Easy-Grow Greenhouse Assembly Instructions 0 Structure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) 07-900
More informationVersion 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS. Victorian Vi-23, 34, 36
Version 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS Victorian Vi-23, 34, 36 PRODUCT INFORMATION Dear customer, Thank you for buying a high-quality aluminium greenhouse. REMARKS The drawings in these instructions
More informationGrowSpan Estate Pro I Greenhouse
GrowSpan Estate Pro I Greenhouse Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104564 11'-8" W x
More information*** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used.
Cleaning *** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used. *** No chemical cleaners can be used on the glass use only mild
More informationASSEMBLY INSTRUCTIONS FOR STORETTE STA42
ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 A01 CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety sake, please read the safety information
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationClearSpan End Frame Kit 26' Wide x 12' High
ClearSpan End Frame Kit 26' Wide x 12' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and struts shown in the above diagram are
More information12 Wide Evolution Cedar Partition Assembly Instructions
06/13 12 Wide Evolution Cedar Partition Assembly Instructions Contents: Introduction Base Preparation Side Assembly Glazing Door Installation Frame Finishing Section - 1 2 3 4 5 Page 3 4 5-6 7 8-9 10-14
More informationXenon 05 Installation Instructions & Parts List
Xenon 05 Installation Instructions & Parts List Illustration Xenon 05, H1 Handle Left Hand: Open Out 26/05/2016 Revision 2.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed by suitably
More informationCORNER ENTRY ENCLOSURE
CORNER ENTRY ENCLOSURE SUPREME INSTALLATION INSTRUCTIONS IMPORTANT - Please read before installation Please read these instructions carefully before starting installation and keep in a safe place for future
More informationEasy2Build TM. 8 x 10 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions
EasyBuild TM Smart Tech solutions 8 x 0 Easy-Grow Greenhouse Assembly Instructions 0 Structure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) 07-900
More informationHinge Door + Side Panel
Hinge Door + Side Panel Instruction Manual KL+ KR Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according
More informationW1209 1/2 10 X 12 SOLARIUM ASSEMBLY INSTRUCTIONS
W09 / 0 X SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested. Base Dimensions x 8, Largest Dimensions x (see pg.3) L:\WP5\Instructions\SOLARIUMS INSTRUCTION BOOKS\W09\ZZZ-09.W09.GP.EN.doc
More informationB A T H R O O M G L A S S
mistley B A T H R O O M G L A S S vaug16 Page 2 Thank you for purchasing this Trinity shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts
More informationE N G L I S H GARDEN SHED. Assembly Instructions. Suitable for Models WITH VARYING DEPTHS
GARDEN SHED Assembly Instructions Suitable for Models 6' Wide 8' Wide 0' Wide WITH VARYING DEPTHS GI0003 November 0 INSTALLATION ADVICE It's Not That Difficult! The construction of your shed isn't as complicated
More informationDeauville Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions
More informationWhite Tongue & Groove 2 Drawer Unit
White Tongue & Groove 2 rawer Unit Assembly Instructions - Please keep for future reference imensions Width - 34cm epth - 28cm Height - 56cm Important - Please read these instructions fully before starting
More informationElite Home-Attached Greenhouse
Elite Home-Attached Greenhouse Photo may show a greenhouse of a different length. Elite Home-Attached Greenhouse Use these instructions for the following greenhouses: #104711 #104713 #104715 2007 ClearSpan
More informationCanterbury 4 DRW CHEST
Canterbury 4 DRW CHEST Assembly Instructions - Please save for future reference 553/4801 565/2178 572/6080 25 kg 55 lbs 9 kg 20 lbs max. Dimensions Width - 84.3cm Depth - 41.9cm Height - 99.7cm Important
More informationHinge Door + Inline Panel + Return Panel
Hinge Door + Inline Panel + Return Panel Instruction Manual DXL2HDR + DXL2HR + DXR Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing
More informationCurium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationGallium 03 Installation Instructions & Parts List
Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed
More informationCurium 19.4H Installation Instructions & Parts List
Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationCold Frame Instructions
1 05/13 Cold Frame Instructions Thank you for purchasing your new Alton cold frame. We recommend you familiarise yourself with the instructions and read all safety information before you commence assembly.
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationStep-by-Step Installation Instructions for
Step-by-Step Installation Instructions for Version 5-06/11 Before Starting: Please read and understand these instructions. Not following these instructions will invalidate your warranty (although this
More information8 Wide Evolution Cedar Partition Assembly Instructions
09/13 8 Wide Evolution Cedar Partition Assembly Instructions Contents: Introduction Overview Base Preparation Partition Frame Assembly Glazing Door Installation Parts List Section - 1 2 3 4 5 Page 3 4
More informationEnglish/French 06/04
E000 PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety
More informationPortofino Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions
More informationDubnium 11 Installation Instructions & Parts List
Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.
More informationLUXURY CURVED QUADRANT SINGLE DOOR
LUXURY CURVD QUADRANT SINGL DOOR 5332 5331 5333 5334 5335 760 x 900mm SINGL DOOR 900mm x 900mm SINGL DOOR 1000mm x 900mm SINGL DOOR 1100mm x 900mm SINGL DOOR 1200mm x 900mm SINGL DOOR INSTALLATION INSTRUCTIONS
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationPremium Solar Star Greenhouse
Premium Solar Star Greenhouse Assembly Instructions SKU# 104901 2006 ClearSpan All rights reserved. Reproduction without permission is prohibited. Revision date: March 2006g Contact your sales representative
More informationPortofino Case2 Installation Guide
Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.
More informationW1610 1/2 10 X 16 SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested.
adlonco@hotmail.com W60 / 0 X 6 SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested. Requires 96 clearance at the wall Base Dimensions 90 x 8, Largest Dimensions 90 x (see pg.3)
More informationModel No. EP84-A, EP84AR-A, P84L
E000 Model No. EP84-A, EP84AR-A, P84L PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationWindsor Arbor. Parts List: General Information: Tools required: Assembly & installation Instructions
Windsor Arbor Assembly & installation Instructions Parts List: General Information:» Read through carefully before beginning assembly.» When assembling components, place on a clean, flat, non-abrasive
More informationExtension Standard building 10/14
Standard building Extension 10/14 8 Wide Victorian Cedar Greenhouse Extension Assembly Instructions Contents: Introduction Base Preparation Overview Base Assembly Side Assembly Frame Assembly Door Installation
More informationHinge Door + One Inline Panel
inge Door + One Inline Panel Instruction Manual KLD + KL Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed
More informationINSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION
INSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION SLIMLINE STEP-BY-STEP INSTALLATION GUIDE Thank you for choosing Roof Maker, we hope you are delighted with your new rooflight. Our roof lanterns
More informationHalf framed 2-Panel Bath Screen
IN00573 (Iss 2) Half framed 2-Panel Bath Screen Instruction suitable for both Right and Left Hand Fixing. Before You Start Check that the bath has been installed correctly and that it is level. Please
More informationPotting Store Assembly Instructions
Before assembly We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The instruction sheet is only a guide to the assembly. Certain
More informationA (mm) B (mm) A (mm) B (mm) 12 x x x ft extension. 8ft extension ft extension ft extension 3720
NOMINAL SIZE A (mm) B (mm) NOMINAL SIZE A (mm) B (mm) 12 x 8 2632 6ft extension 1860 12 x 10 3824 3252 12 x 12 3872 8ft extension 2480 10ft extension 3100-12ft extension 3720 Thank you for purchasing your
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationNOMINAL SIZE A (mm) B (mm)
NOMINAL SIZE A (mm) B (mm) X 1990 X 8 198 210 X 10 3230 X 12 3850 Thank you for purchasing your new Robinsons greenhouse. We recommend you familiarise yourself with the instructions and read all safety
More informationENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH
ENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH RAFTER PREPERATION RAFTER PREPARATION A FRAME PREPERATION AND ASSEMBLY A FRAME PREPARATION AND ASSEMBLY... Open boxes, remove
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationAssembly instructions. 6x4. Model GH1354A. 6x6. Model GH1357A. 6x8. Model GH1360A. 6x10. Walk-in Greenhouse. Model GH1363A
ssembly instructions x Model GH x Model GH7 x8 Model GH0 x0 Model GH Walk-in Greenhouse Statement ear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following the detailed
More informationPlayground Assembly Instructions
Before You Begin Playground Assembly Instructions Locate the playground set on firm, level ground. Assemble the playground on or close to its permanent location Two people are recommended to assemble the
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationS H E D A S S E M B L Y I N S T R U C T I O N S
T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 8 X 10 ft Approx = 2550 x 3140 cm COMPONENT LIST Component illustrations are given as a visual guide only and are not in proportion PART
More informationExtension Standard building 03/15
Extension Standard building 03/15 8 Wide Evolution Extension Assembly Instructions Contents: Introduction Base Preparation Overview Base Assembly Side Assembly Front Assembly Extension Installation Rear
More informationINFINITE RANGE - CENTRE FOLDING DOOR
INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR + 2 SIDE RETURN PANELS (PENINSULA) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out
More informationPerfect Fit blinds. Preparation. Measuring Instructions. Step 1 - Measure glass size. Step 2 - Measure window depth
Preparation Before you begin, ensure there is a 6mm clearance all around the outside of your window beading to allow enough room for the Perfect Fit framework. Also check that the seals of your window
More informationCorner Potting Store Assembly Instructions
Corner Potting Store Assembly Instructions English SS225E Before assembly We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The
More informationNOMINAL SIZE. A (mm) B (mm) 8 X 6 8 X 8 8 X X
NOMINAL SIZE A (mm) B (mm) X 6 1990 X 259 2610 X 10 3230 X 12 350 Thank you for purchasing your new Robinsons greenhouse. We recommend you familiarise yourself with the instructions and read all safety
More informationNOMINAL SIZE A (mm) B (mm)
NOMINAL SIZE A (mm) B (mm) x 2012 x 8 232 1972 x 10 3252 x 12 3872 Thank you for purchasing your new Robinsons greenhouse. We recommend you familiarise yourself with the instructions and read all safety
More informationWall Profiles 2 Pozi Screwdriver. Wall Profile Covers 4 Sealant. Large Panel and Thin Panel Assemblies Sealant Gun
Decem Sliding Door (Corner Fitting) Instruction Manual DXT Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed
More informationZero Threshold TM. Hints and Tips Handbook. Birdlip. Burford. Blockley. Bourton
Birdlip Burford Zero Threshold TM Hints and Tips Handbook Blockley www.edengreenhouses.com Bourton Customer Helpline: +44 (0)1242 676625 Mon Fri 9:00am 5:00pm mail@eden greenhouses.com EH 1.02 Dear Customer,
More informationAssembly Instructions
Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel
More informationSliding Door Kit
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More informationClearSpan End Frame Kit 30' Wide x 11' High
ClearSpan End Frame Kit 30' Wide x 11' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and mounting feet shown in the above diagram
More informationS H E D A S S E M B L Y I N S T R U C T I O N S
T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 6 X 4ft = 190 x 150 cm 6 X 6ft = 190 x 190 cm 6 X 8ft = 190 x 255 cm COMPONENT LIST Component illustrations are given as a visual guide
More information1 Door Corner Robe. Assembly Instructions - Please keep for future reference. 001 xx 4057
1 Door Corner Robe ssembly Instructions - Please keep for future reference 001 xx 4057 Dimensions Width - 64.7cm Depth - 64.7cm Height - 179.9cm MDE IN GRET RITIN Important - Please read these instructions
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationLOCKN LOAD FIRST TIME INSTALLATION
LOCKN LOAD TM TRACK MOUNTING KIT ISUZU MU-X 2013+ LS-M & LS-U MODELS ONLY 3 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES
More informationROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here.
ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. Parts List - Tables Tops, Top Insert Panels and Base panels
More informationAssembly Instructions
18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,
More informationSHOWERLUX HELPLINE: TEL: SHOWERLUX (UK) Ltd.
SHOWERLUX HELLIE: TEL: 02476 882518 Fax: 02476 882539 Email: technical@showerlux.co.uk Email: spares@showerlux.co.uk SHOWERLUX (UK) Ltd. Sibree Road, Coventry, West Midlands CV3 4FD Tel: 02476 639400 Fax:
More informationW X 12 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly
adlonco@hotmail.com W07-3 8 X SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly Requires 96 clearance at the wall Base Dimensions x 9 /, Largest Dimensions x98 / (see pg.) ZZZ-87.W07-3.7-5.GP.EN.HER.doc
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More informationWalton - Tall Cupboard
Walton - Tall upboard ssembly Instructions - Please keep for future reference 151/8113 Dimensions Width - 80.5cm Depth - 39cm eight - 152.5cm MD IN RITIN Important - Please read these instructions fully
More information