INSTALLATION INSTRUCTIONS
|
|
- Miles Perkins
- 6 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Accessory ROOF RACK (BLACK) Application 2010 MDX Publications No. BII Issue Date APRIL PARTS LIST Right center stay Right side rail Left side rail Left center stay Right front rail cover Right center stay cover Left front rail cover Left center stay cover Right rear rail cover 4 TORX screws Left rear rail cover 2 Rail cover lids 12 TORX nuts 2 Rail covers 10 Spacers 2010 American Honda Motor Co., Inc. All Rights Reserved. BII (1004) 08L02-STX-2B of 6
2 TOOLS AND SUPPLIES REQUIRED Eye protection (face shield, safety goggles, etc.) Plastic Trim Tool (T/N SILTRIMTL10) T30 TORX bit Torque wrench Reciprocating saw (air saw) with 32 tpi blade Snap-on: AT192A or equivalent Tape measure Shop towel Blanket Empty box Felt-tip pen 2. Open the tailgate. Using a plastic trim tool, pry up on the left roof molding to release the clip. TAILGATE (Open.) INSTALLATION Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be extremely careful not to damage the paint and other surfaces when installing the roof rails. These instructions are for the left side of the vehicle. The same procedure applies to the right side of the vehicle. 1. Measure forward from the rear of the left roof molding, and mark the left roof molding at the measurement shown. 3. Continue to remove the left roof molding only on the roof area by lifting the left roof molding upward to release six more clips. Do not remove the left roof molding along the windshield. PLASTIC TRIM TOOL BS 1673 mm (65.8 in.) 6 S BS AS 2 of 6 BII (1004) 2010 American Honda Motor Co., Inc. All Rights Reserved.
3 4. Tie a shop towel around the rear edge of the left roof molding to avoid scratching the roof. 6. Place an empty 75 mm (3 in.) box under the left roof molding near the mark. SHOP TOWEL 75 mm (3 in.) EMPTY BOX AS 5. Place a blanket over the roof of vehicle under the left roof molding at the mark AS 7. While wearing eye protection, cut the left roof molding at the mark using an air saw. Have an assistant hold the rear edge near the shop towel of the left roof molding while cutting. NOTE: Do not use a cutting wheel or shears to cut the left roof molding, it will damage the left roof molding. BLANKET AS AIR SAW AS 8. Remove the empty box and blanket American Honda Motor Co., Inc. All Rights Reserved. BII (1004) 3 of 6
4 9. Turn the left roof molding over, and remove the seven clips from the left roof molding. If any clip stayed to the roof, remove it. 12. Reinstall three of the seven clips removed in step 9. SPACER 5 mm (0.2 in.) ROOF 3 CUT PIECES OF (Reuse.) 3 S (Reuse.) CS 10. On the work bench, measure and mark the left roof molding at the measurements shown. 13. Install five spacers to the ends of the cut pieces of the left roof molding. 14. Reinstall the cut pieces of the left roof molding on the vehicle BS 75 mm (3.0 in.) 606 mm (23.8 in.) 195 mm (7.7 in.) 3 CUT PIECES OF 625 mm (24.6 in.) 172 mm (6.8 in.) STUD BOLT Discard. 606 mm (23.8 in.) CUT PORTION OF AIR SAW 625 mm (24.6 in.) AS 11. While wearing eye protection, use an air saw to cut the left roof molding at the marks you made. Make the cuts on the work bench AS 4 of 6 BII (1004) 2010 American Honda Motor Co., Inc. All Rights Reserved.
5 15. Place the left center stay over the two stud bolts at the center, and install two TORX nuts. Torque the TORX nuts to 12 to 15 N m (9 to 11 lbf ft). 17. Place the left side rail over the four remaining stud bolts. 2 TORX NUTS 12 to 15 N m (9 to 11 lbf ft) STAY 2 STUD BOLTS 4 STUD BOLTS AS 16. Attach the left center stay cover to the left center stay AS 18. At the left center stay cover, install two TORX screws through the holes in the left side rail. Torque the TORX screws to 7 to 12 N m (5 to 9 lbf ft). STAY COVER 2 TORX SCREWS 7 to 12 N m (5 to 9 lbf ft) STAY STAY COVER AS BS 2010 American Honda Motor Co., Inc. All Rights Reserved. BII (1004) 5 of 6
6 19. Install four TORX nuts to attach the front and rear of the left side rail. Torque the TORX nuts to 12 to 15 N m (9 to 11 lbf ft). 22. Insert the tabs of the left front rail cover and left rear rail cover in first, and install the left front rail cover and left rear rail cover on the left side rail. 2 TORX NUTS 12 to 15 N m (9 to 11 lbf ft) 2 TORX NUTS 12 to 15 N m (9 to 11 lbf ft) LEFT REAR RAIL COVER TAB LEFT RAIL COVER TAB LEFT SIDE RAIL RAIL COVER 20. Install the rail cover lid on the rail cover AS LEFT SIDE RAIL LIP OF SIDE RAIL AS RAIL COVER LID 23. Repeat steps 1 through 22 to install the right side rail on the right side of the vehicle. RAIL COVER STAY COVER AS 21. Install the rail cover into the hole in the center of the left side rail. 6 of 6 BII (1004) 2010 American Honda Motor Co., Inc. All Rights Reserved.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK (BLACK) P/N 08L02-STX-210B Application 2013 MDX Publications No. BII 13434 Issue Date JULY 2012 PARTS LIST Right side rail Right center stay Left side rail
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK RAILS P/N 08L02-T0A-110 Application 2012 CR-V Publications No. AII 12087 Issue Date DEC 2011 PARTS LIST Left roof rack rail Right roof rack rail Cap A, left
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RAILS P/N 08L02-TX4-200 Application 2018 RDX Publications No. VERSION 1 Issue Date MAY 2017 PARTS LIST Right center stay Roof left rail Left center stay Roof right
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S AND CROSS BARS Application 2009 PILOT Publications No. AII 39407 Issue Date MAY 2008 PARTS LIST 4 Roof molding clips Left side roof rack TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25829 2004 MDX Issue Date SEP 2003 PARTS LIST Tailgate spoiler Right cover Left cover 2 Flat-head screws 2 Turn nuts TOOLS AND SUPPLIES
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory CARGO NET P/N 08L96-TR0-100 Application 2012 CIVIC 2 AND 4-DOOR Publications No. AII 45607 Issue Date APR 2011 PARTS LIST Accessory User s Information Manual Cargo net
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS LUGGAGE NET P/N 08L96-TL2-200 2009 TSX BII 38592-39370 Issue Date APRIL 2008 PARTS LIST 2 6 x 20 mm Hex bolts Luggage net 2 6 x 16 mm Hex
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS AERO 2009 TSX BII 39056 Issue Date APRIL 2008 PARTS LIST TOOLS AND SUPPLIES REQUIRED Front aero bumper Phillips screwdriver Flat-tip screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 30914 UNDER SPOILER 2006 TL Issue Date SEP 2005 PARTS LIST Front under spoiler Template B Left bracket (Marked L) Left cover (Marked
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory P/N 08U35-SZN-200 Application 2012 ZDX Publications No. BII 46578 Issue Date AUG 2011 PARTS LIST 2 Rivet nuts (5 mm) Cargo cover 8 Self-tapping screws, 5 x 50 mm Left base 8 Self-tapping
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2011 RIDGELINE Publications No. AII 43440 Issue Date JUNE 2010 PARTS LIST Left tube 6 Hex bolts Right tube (with label)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2003 ACCORD AII 24040 4-DOOR CARGO NET P/N 08L96-SDA-100 Issue Date AUG 2002 PARTS LIST Cargo net 2 Anchors TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2010 RIDGELINE Publications No. AII 42145 Issue Date AUG 2009 PARTS LIST Left tube 2 Washers 2 Well nuts Right tube (with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2011 MDX Publications No. BII 43668 Issue Date AUG 2010 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory MOON P/N 08R01-TR0-100 Application 2013 CIVIC 4-DOOR Publications No. AII 13080 Issue Date NOV 2012 Put this information in the glove box with the vehicle owner s manual.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-TR0-100A Application 2013 CIVIC 4-DOOR Publications No. AII 13081 Issue Date NOV 2012 PARTS LIST 2 Grommets B Left front splash guard 2 Self-tapping screws,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-TK6-100 Application 2013 FIT (BASE MODEL) Publications No. AII 13241 Issue Date JULY 2012 PARTS LIST Right front splash guard TOOLS AND SUPPLIES REQUIRED
More informationTOYOTA TACOMA ROOF RACK Preparation. Part Number: PT
Preparation Part Number: PT278-35140 Kit Contents Item # Quantity Reqd. Description 1 1 LH Base Rail Assembly w/ Crossbar 2 1 RH Base Rail Assembly 3 1 Hardware Bag 4 2 Brackets 5 1 Front Crossbar Assembly
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationCustom Grille Insert
1 of 8 Thank you for your purchase of DBCustomz 2016+ Toyota Tacoma! This product was carefully crafted to ensure a perfect fit with your vehicle. The instructions below are provided to allow for an easier
More informationSCION tc 2005 PEDESTAL SPOILER Preparation. Part Number: PT47A XX PT47A XX PT47A XX
Preparation Part Number: PT47A-21052-XX PT47A-21062-XX PT47A-21082-XX Kit Contents Item # Quantity Reqd. Description 1 1 Painted Spoiler Assembly 2 1 LH Gas Strut 3 1 RH Gas Strut 4 1 Hardware Bag Hardware
More informationSCION FR-S REAR SPOILER Preparation
Preparation Part Number: PT938-18130-XX Kit Contents Item # Quantity Reqd. Description 1 1 Spoiler 2 2 Strut 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 M6 x 1 Nut with
More informationACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)
ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationSide and rear window, assembly overview
64-7 Side and rear window, assembly overview 1 - Side/rear window Removing Unbroken Page 64-9 Broken Page 64-11 Installing Page 64-13 Curing time Page 64-21 Re-sealing Page 64-25 2 - PUR adhesive sealant
More informationV Installation instructions, accessories. Auxiliary seat. Volvo Car Corporation Gothenburg, Sweden V70 (00-08) 2002
Installation instructions, accessories Instruction No 8624018 Version 1.3 Part. No. 30749269, 30749270, 30749271, 30749272, 30749273, 30749274 Auxiliary seat M8901699 Volvo Car Corporation Auxiliary seat-
More informationGMC Cut-Out Fender Flares Set of 4
GMC Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: REAR SPOILER KIT - CARBON FIBER INFINITI Q60 T99J1 5CH0B KIT CONTENTS: Item Qty. Part Description A 1 Spoiler Assembly B 4
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationGMC Cut-Out Fender Flares Set of 4
GMC Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to
More information8030 Synergy Jeep JK Rear Long Arm Frame Brackets
General Notes: SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8030 Synergy Jeep JK Rear Long Arm Frame Brackets These instructions are also available on our website; www.synergymfg.com.
More informationRusty s JL Winch Mount RR-WM55-JL INSTALLATION INSTRUCTIONS
Rusty s JL 2018+ Winch Mount RR-WM55-JL INSTALLATION INSTRUCTIONS Introduction: Rusty s recommends that this installation be performed by a certified automotive technician or a person with professional
More informationWARNING VW Jetta New Installation Instructions BX3823. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Running Boards Kit Nissan Pathfinder/ Infiniti QX60 999T6 X5060 (Pathfinder Running Board Kit) 999T6 R5060 (Infiniti QX60
More informationFENDER FLARE INSTALLATION
Part#: TG-FF8G4158 FOR 2007-2013 GMC Sierra 1500 Pickup Truck (Exclude 69.3inch Short Bed Models) FENDER FLARE INSTALLATION Hardware Kit Included IMPORTANT TYGER only approves the installation according
More informationRepair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION.
Replacing a La Z Time Mechanism Side Subassembly Tools Required: Slotted Screwdriver Power Driver 8" Driver Extension Ruler Note: Extension springs are not typically used on non-chaise standard width styles,
More informationFinish Line Emergency Brake Boot INSTRUCTION SHEET. Part Number. Application: Corvette. Part Includes.
Application: 1997-2004 Corvette Part Includes 1 - Emergency Brake Boot Finish Line Emergency Brake Boot Tools Needed T15 10mm PRE-INSTALLATION NOTES Read completely through instructions to familiarize
More informationGMC Cut-Out Fender Flares Front Pair
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationINSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES
INSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES Thank you for your purchase of Crawler Conceptz Ultra Series Front Fender Flares. While these flares are easily installed with basic hand tools and
More informationTOYOTA COROLLA EC REARVIEW MIRROR Section I Installation Preparation
Section I Installation Preparation Part Number: PT374-02030 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass & Maplights 2 1 Hardware Bag
More informationService Bulletin
Service Bulletin 18-026 April 24, 2018 Version 5 Safety Recall: Left (Driver Side) Second Row Seat Recliner Does Not Lock Supersedes 18-026, dated April 7, 2018 to revise the information highlighted in
More informationFENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED
` FENDER FLARE Part No: FFD3001S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationInstall. instructions. B8 A4/S4 RS4 Blackout Mesh Style Grille. By: 7716 Wiles Rd.Coral Springs, FL
Install instructions B8 A4/S4 RS4 Blackout Mesh Style Grille By: Preface: The best fitting grille on the market! Completely change the look of your Audi A4 or S4. This mesh style grille features a black
More informationBX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT
BX2173 Installation Instructions 2000-04 Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT Serial No. The front fascia, coolant line bracket and anti-pollution devices are removed for baseplate
More informationToyota Pocket Style Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationToyota Pocket Style Fender Flares Set of 4
Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationWARNING Honda Civic (Incl. EX, LX, DX) Installation Instructions BX2243. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-665) Ford Crown Victoria, Mercury Grand Marquis 1992-2010 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint
More informationTOYOTA CAMRY LIP SPOILER Preparation
Preparation Part Number: PT29A-03070-XX Kit Contents 1 1 Lip Spoiler 2 1 Hardware Bag Hardware Bag Contents 1 2 M6 Nuts 2 2 M6 Bolts Additional Items Required For Installation 1 1 Installation Kit, P/N
More informationSuggested Instructions for: , , , C5 Emergency Brake Boot
Suggested Instructions for: 608-348, 608-349, 614-653, 619-200 C5 Emergency Brake Boot Tools Ratchet, 10mm socket, extension #15 Torx screwdriver Needle nose pliers Masking Tape Very small flat head screwdriver
More informationPROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT
AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar
More informationTOYOTA TACOMA SLIMLINE II RACK ( 1165MM x 1358MM)
TOYOTA TACOMA SLIMLINE II RACK ( 1165MM x 1358MM) FATT001 / KRTT001T INSTALL TIME: 60 mins READ ME FIRST: Thank you for purchasing a Front Runner Slimline II Rack. This Roof Rack consists of a kit that
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-584) Ford Focus 2000-2007 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationGEN II Toyota Prius Back Door Opener Switch Replacement & License Plate Lights
GEN II Toyota Prius Back Door Opener Switch Replacement & License Plate Lights Rubber Surface of Switch had Degraded to Tar-like Substance Vehicle Manufacture Date 10/06 OLD SWITCH IN GARNISH SWITCH REMOVED
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationBolt-On/Rugged Fender Flares GMC Sierra 1500/2500/3500 (14-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationFRONT BUMPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
FRONT BUMPER KIT P/N 2882301 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationINSTALL INSTRUCTIONS
Jeep JK Rear Corner Skins Product : JK200,JK201,JK202,JK203 Applica on : 2007+ Jeep Wrangler JK ( 2 Door and 4 Door ) Page ( 1 of 6 ) I WARNING Read the instruc ons completely before beginning installa
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar
More informationVolvo Car Customer Service QB Instruction VCC
Volvo Car Customer Service Title Inflatable curtain Page 1 ( 24 ) Action Bolt replacements Operation number: 97184-2 Issue Date Reason 1 2017-02 First issue 2 2017-03 Technical content change Affected
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-870) Ford Windstar 1995 2003, Ford Freestar 2004 2006 & Ford Monterey 2004 2006 General Tech Tips: Use painter s tape rather than duct tape to secure window. It
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationPage 1 of 5 Instructions for Fitting Lower Grille to S Type Jaguar. Part Code 9048
Page 1 of 5 Instructions for Fitting Lower Grille to S Type Jaguar. Part Code 9048 To fit this grille you will need: Torch, 10mm spanner, 10mm socket with extension, T30 torx bits, Screwdrivers, Pliers,
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationIncluded in Hardware Kit: Toyota Tacoma, Regular/Access/Double Cab, Shortbed Set Part # Rev STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationMM Strut Tower Brace, GT (MMSTB-5.1)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Strut Tower Brace, 1996-97 GT (MMSTB-5.1) MMSTB-5.1 is for 1996-97 GT s with
More informationMaster Your Terrain. (307)
Master Your Terrain (307) 775 9565 www.tntcustoms.com Rear Swing-out Tire Carrier Jeep TJ/LJ Installation Instructions Congratulations for purchasing a T&T Customs, Inc. Rear Swing-out Tire Carrier for
More informationMM Strut Tower Brace, Cobra (MMSTB-7)
The MM strut Tower Brace attaches to each strut tower and to the firewall. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM
More informationRubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs
Jeep Cherokee ZJ Set Part #10916-07 Rev-2 03-11-10 THESE INSTRUCTIONS INVOLVE CUTTING THE FENDERS OF THE VEHICLE. IT IS IMPORTANT TO READ ALL INSTRUCTIONS PRIOR TO THE CUTTING AND INSTALLATION OF THESE
More informationClassic SportBar Camaro V6 or V8
Classic SportBar 2011-2015 Camaro V6 or V8 The Classic SportBar is intended for restyling purposes only and does NOT provide roll over protection. Read entire installation guide before starting. Component
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationTOYOTA TACOMA 2005 TRAILER WIRE HARNESS Preparation
Preparation Part Number: 08921 04960 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Converter Assembl y 2 1 Wire Harness
More informationRAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED
RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL
More informationDriver/Left Top. Support Bracket
PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm
More informationPARTITION INSTALLATION INSTRUCTIONS
PARTITION INSTALLATION INSTRUCTIONS 2015 Chevrolet Tahoe PPV / Part Number 5703FW, FWA & FEW Do not attempt to install this product on any vehicle equipped with third row seating! Parts List Distributed
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 645 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,
More informationFord F150 Rear Flares Set Part # Revision
Ford F150 Rear Flares Set Part # 20074 Revision 1 04-01-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationIncluded in Hardware Kit: GMC Boss Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-7 2/17/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description
` FENDER FLARE Part No: FFC3002S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required
More information2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions
2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2.
More informationIncluded in Hardware Kit: GMC Boss Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-7 1/22/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationWARNING Honda Civic (Incl. EX, LX, DX) Installation Instructions BX2243. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationG37 CONVERTIBLE; SQUEAK / RATTLE / BUZZ NOISE FROM ROOF AREA
Classification: Reference: Date: BT11-031 ITB12-003 January 13, 2012 2009-2011 G37 CONVERTIBLE; SQUEAK / RATTLE / BUZZ NOISE FROM ROOF AREA This bulletin supersedes ITB10-071. Discard all copies of ITB10-071.
More informationTOYOTA TACOMA TRAILER WIRE HARNESS Preparation
Preparation Part Number: PT725-35120 Kit Contents Item Quantity Reqd. Description # 1 1 Flasher Assembly (F/A) 2 1 Wire Harness 3 1 Sub Wire Harness 4 2 Plastic Tie (300mm) 5 4 Plastic Tie (200mm) 6 13
More informationPolaris General Doors #06016 Installation & Operations Manual Fits Polaris General
Polaris General Doors #06016 Installation & Operations Manual Fits Polaris General Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door
More informationFig. 1 Fig. 2. Fig. 3 Fig. 4 TOOLS REQUIRED: *Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS:
*Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS: 2EA. 6X9 TWO WAY SPEAKERS P/N 05030281AA 1EA. INSTRUCTIONS P/N RBI05LXREAR 300c and Charger 1. Remove the lower
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit :
Jeep Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/4 Attachment Tab Width: 21-3/4 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products
More informationBe sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More information