INSTALLATION INSTRUCTIONS
|
|
- Dale Atkins
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Accessory MOON P/N 08R01-TR0-100 Application 2013 CIVIC 4-DOOR Publications No. AII Issue Date NOV 2012 Put this information in the glove box with the vehicle owner s manual. PARTS LIST Moonroof visor 2 Front brackets (marked A) 2 Side brackets (marked B) 4 Screws 4 Nuts 4 Protective tapes TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 10 mm Offset wrench Ruler Isopropyl alcohol 3M Protective tape application solution Shop towel Masking tape Felt-tip pen Torque Screwdriver (T/N CDI401SM) (Available through the Honda tool and Equipment program. On the in, click on: Service/Service Bay/Tool and Equipment Program, then enter the number under Search. Or call ) High-quality paste wax INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be careful not to damage the body paint finish. This moonroof visor kit should be installed only if the ambient air temperature is 15 C (60 F) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer. 1. Clean and wax the area to be covered with a highquality paste wax. 4 Collars 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1211) 08R01-TR of 6
2 2. Open the moonroof. Roll up two shop towels, and insert them between the roof panel and air deflector to lower the air deflector. Be careful not to damage the air deflector. 4. Using isopropyl alcohol on a shop towel, clean the roof panel at each of the two marks you made, but don t wipe off the marks. FRONT AIR DEFLECTOR 2 SHOP TOWELS (Insert into the corners.) Clean using isopropyl alcohol. MARK 6 mm MOON Q080601AJ 3. Locate the edge of the indentation on the right side and left side of the moonroof opening. Measure 40 mm (1.6 in.) to the front of the vehicle, and make one mark on each side of the roof panel. Clean using isopropyl alcohol. MARK EDGE OF 6 mm 45 mm FELT-TIP PEN Q080603DJ 5. Remove the adhesive backings from two pieces of protective tape, and attach them to the roof panel at the two marks you made. Allow 6 mm of each protective tape to hang below the bottom lip of the roof panel. Remove the marks. EDGE OF 45 mm FELT-TIP PEN Q080602CJ 2 of 6 AII (1211) 2012 American Honda Motor Co., Inc. All Rights Reserved.
3 6. Locate the third indentations along the front edge of the moonroof opening. Using isopropyl alcohol on a shop towel, clean the roof area and the inside edge of the moonroof opening where the protective tapes will attach. 8. Place two side brackets (marked B) into position over the protective tape and around the lip of the roof opening, and secure them into position with a piece of masking tape. NOTE: Be careful not to crease the protective tape. Align. Clean using isopropyl alcohol. THIRD (Wrap the tape using the side bracket.) SIDE BRACKET (Marked B) SIDE BRACKET (Marked B) Q080604CJ 7. Remove the adhesive backing from one of the protective tapes. Starting at the top edge of the moonroof opening, wrap one protective tape around the lip of the moonroof opening to cover one of the located indentations. SIDE BRACKET (Marked B) MASKING Q080605CJ 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1211) 3 of 6
4 9. Place the two front brackets (marked A) into position over the protective tape and around the lip of the roof opening, and tape them into position with a piece of masking tape. Be sure to align the lower end of the front brackets with the indentation in the lip. NOTE: Be careful not to crease the protective tape. FRONT BRACKET (Marked A) 10. Using 3M protective tape application solution, spray the roof in the area shown where the moonroof visor will attach. MOON 2 SCREWS (Loosely install.) 2 COLLARS MASKING (Wrap the tape using the front bracket.) 2 BRACKETS A 2 NUTS FRONT FRONT BRACKET (Marked A) FRONT BRACKET (Marked A) MASKING Q080606DJ 11. Set the moonroof visor on the vehicle roof in front of the moonroof opening, and adjust its position so the holes in the moonroof visor are aligned with the bracket holes. Loosely install the moonroof visor to the front brackets with two screws, two collars, and two nuts. Remove the masking tape. 12. Loosely install the moonroof visor to the side brackets with two screws, two collars, and two nuts. Remove the masking tape. 2 SCREWS (Loosely install.) 2 COLLARS MASKING 2 NUTS 2 BRACKETS B MOON 4 of 6 AII (1211) 2012 American Honda Motor Co., Inc. All Rights Reserved.
5 13. Position the moonroof visor with equal spacing on all sides. Check that the rubber molding is not twisted or rolled under the moonroof visor. 14. While holding the side brackets against the roof panel, tighten the two screws and nuts on the side bracket. While holding the front brackets against the roof panel, tighten the two screws and nuts on the front brackets. Using a torque screwdriver, torque all of screws to 2.0 N m (1.5 lbf ft). NOTE: Excessive wind noise may occur if the brackets are not flush against the roof panel. 15. Wipe off any excessive application solution. Equal spacing RUBBER MOLDING (Not twisted or rolled under the moonroof visor.) SIDE SCREW (Tighten.) COLLAR BRACKET B NUT Parallel with each other. Equal spacing SECTION VIEW BRACKET B Push. Make sure there is no gap in this area. MOON SCREW (Tighten.) FRONT NUT COLLAR MOON Push. BRACKET A 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1211) 5 of 6
6 16. Remove the shop towels inserted in step 2. Remove the IMPORTANT INFORMATION label. IMPORTANT INFORMATION LABEL MOON Q080610BJ CARE OF THE MOON To avoid damaging the surface, do not use organic solvents such as gasoline, ammonia based cleaners, or solvents to the moonroof visor. Clean with neutral detergent and water using a soft cloth or chamois. To remove fine scratches and restore the original luster, use Meguiar s Mirror Glaze plastic cleaner and polish or an equivalent high-quality plastic cleaner. 6 of 6 AII (1211) 2012 American Honda Motor Co., Inc. All Rights Reserved.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory CARGO NET P/N 08L96-TR0-100 Application 2012 CIVIC 2 AND 4-DOOR Publications No. AII 45607 Issue Date APR 2011 PARTS LIST Accessory User s Information Manual Cargo net
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 30914 UNDER SPOILER 2006 TL Issue Date SEP 2005 PARTS LIST Front under spoiler Template B Left bracket (Marked L) Left cover (Marked
More informationINSTALLATION INSTRUCTIONS
SG57f GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION: Sunroof Wind Deflector. APPLICATION: Pathfinder; Frontier with no roof rails 3. PART NUMBER: 999D4-XR00 4. KIT CONTENTS: Item No. ) ) 3) 4) 5)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25829 2004 MDX Issue Date SEP 2003 PARTS LIST Tailgate spoiler Right cover Left cover 2 Flat-head screws 2 Turn nuts TOOLS AND SUPPLIES
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK (BLACK) P/N 08L02-STX-210B Application 2013 MDX Publications No. BII 13434 Issue Date JULY 2012 PARTS LIST Right side rail Right center stay Left side rail
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK (BLACK) Application 2010 MDX Publications No. BII 42095-43814 Issue Date APRIL 2010 1PARTS LIST Right center stay Right side rail Left side rail Left center
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2011 MDX Publications No. BII 43668 Issue Date AUG 2010 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-TR0-100A Application 2013 CIVIC 4-DOOR Publications No. AII 13081 Issue Date NOV 2012 PARTS LIST 2 Grommets B Left front splash guard 2 Self-tapping screws,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S AND CROSS BARS Application 2009 PILOT Publications No. AII 39407 Issue Date MAY 2008 PARTS LIST 4 Roof molding clips Left side roof rack TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2011 RIDGELINE Publications No. AII 43440 Issue Date JUNE 2010 PARTS LIST Left tube 6 Hex bolts Right tube (with label)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-TK6-100 Application 2013 FIT (BASE MODEL) Publications No. AII 13241 Issue Date JULY 2012 PARTS LIST Right front splash guard TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2010 RIDGELINE Publications No. AII 42145 Issue Date AUG 2009 PARTS LIST Left tube 2 Washers 2 Well nuts Right tube (with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK RAILS P/N 08L02-T0A-110 Application 2012 CR-V Publications No. AII 12087 Issue Date DEC 2011 PARTS LIST Left roof rack rail Right roof rack rail Cap A, left
More informationLANCER LOWER GRILLE GARNISH KIT MZ INSTALLATION AND HANDLING INSTRUCTIONS
LNCER LOWER GRILLE GRNISH KIT MZ940000 INSTLLTION ND HNDLING INSTRUCTIONS Thank you for purchasing the Mitsubishi Genuine ccessory. To install and use the product correctly with proper knowledge of it,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Kit G Coupe 999J2 JxxxxB4 (xxxx Designates model year and color) Item Qty. Description Part Number
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory P/N 08U35-SZN-200 Application 2012 ZDX Publications No. BII 46578 Issue Date AUG 2011 PARTS LIST 2 Rivet nuts (5 mm) Cargo cover 8 Self-tapping screws, 5 x 50 mm Left base 8 Self-tapping
More informationGENUINE FRONT UNDER GARNISH
GENUINE FRONT UNDER GARNISH INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, please thoroughly read these instructions. For your
More informationBolt-On/Rugged Fender Flares GMC Sierra 1500/2500/3500 (14-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationBolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RAILS P/N 08L02-TX4-200 Application 2018 RDX Publications No. VERSION 1 Issue Date MAY 2017 PARTS LIST Right center stay Roof left rail Left center stay Roof right
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2003 ACCORD AII 24040 4-DOOR CARGO NET P/N 08L96-SDA-100 Issue Date AUG 2002 PARTS LIST Cargo net 2 Anchors TOOLS AND SUPPLIES REQUIRED
More informationASX / OUTLANDER SPORT MZ538307EX SIDE MOULDING INSTALLATION AND HANDLING INSTRUCTIONS
ASX / OUTLANDER SPORT MZ538307EX SIDE MOULDING INSTALLATION AND HANDLING INSTRUCTIONS Side moulding Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with
More informationIsuzu D-Max Part Numbers Black Polished
SB007 Sports Bar Fitting Instructions Isuzu D-Max 0 Part Numbers - 55000 - Black - 5000 - Polished Installation Time: 0 min (Approximately) PLEASE KEEP INSTRUCTIONS IN GLOVE BOX FOR FURTHER USE RECOMMENDED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationQWALL 5.2 (2 Back Panels)
QWALL 5. ( Back Panels) SHOWER ACRYLIC WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationBolt-On/Rugged Fender Flares Toyota Tundra (14-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY Extrusion 28.0 ft Short Screw 18 Nuts 42 Alcohol Wipe 4 Long
More informationStep-by-Step Installation Instructions for
Step-by-Step Installation Instructions for Version 5-06/11 Before Starting: Please read and understand these instructions. Not following these instructions will invalidate your warranty (although this
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationPart Number: ;-02;-03;-08;-10;-11;-18;-21
Document # 4065 4/3/06 TOYOTA MATRIX 2006 - FENDER FLARES Section I Installation Preparation Part Number: 00016-12120-01;-02;-03;-08;-10;-11;-18;-21 Code: SF1 Kit Contents Item # Quantity Reqd. Description
More informationInstallation Guide. brighter. lighter.
Installation Guide brighter. lighter. storing and handling dekō markerboards Protective Film The face of each dekō markerboard is protected by high quality polyethylene film. The protective film is left
More informationInstallation Instructions
MUSTANG RTR SIDE ROCKER SPLITTER KIT Part # 1011-7000-01 Application: 2010-2014 Mustang Installation Instructions Before installing your RTR components, rear through the entire installation process and
More informationFENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED
` FENDER FLARE Part No: FFD3001S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required
More informationChapter 32 - Hood, Deck, Fenders & Running Boards Installation (Video Clip 32)
Chapter 32 - Hood, Deck, Fenders & Running Boards Installation (Video Clip 32) 1166. Polish the hood handle with chrome polish and then install the handle onto the hood. 1167. Use a 10mm socket and from
More informationTOYOTA MATRIX FENDER FLARES
Document # 2880 Created 11/29/04 TOYOTA MATRIX 2005 - FENDER FLARES Section I Installation Preparation Part Number: 00016-12120-01;-02;-03;-08;-10;-11;-18;-21 Code: SF1 Kit Contents Item # Quantity Reqd.
More informationCurium 19.4H Installation Instructions & Parts List
Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationAeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material
Aeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material User s Guide Product Description: The Aeon CLR Series is an ultra-short throw fixed
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: REAR SPOILER KIT - CARBON FIBER INFINITI Q60 T99J1 5CH0B KIT CONTENTS: Item Qty. Part Description A 1 Spoiler Assembly B 4
More informationGallium 03 Installation Instructions & Parts List
Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationTOYOTA TUNDRA 2015 BLACK TEXTURED FENDER FLARE
TOYOTA TUNDRA 2015 BLACK TEXTURED FENDER FLARE Part Number: 00016-34083-02 Accessory Code: BF1000 Conflicts Note: Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right Front
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationSoutheast Toyota Tacoma 4-Door Roof Rack DEALER INSTALLED
Parts list 1- Right side rail assembly 1- Left side rail assembly 2- Cross bars 4- Protective gaskets 4- Screws M5 x 13mm long 8- Riv-nuts ¼ -20 8- Screws ¼ -20 x 3/4 Tools needed for installation Safety
More informationCurium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationRAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED
RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL
More informationTOYOTA COROLLA EC REARVIEW MIRROR Section I Installation Preparation
Section I Installation Preparation Part Number: PT374-02030 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass & Maplights 2 1 Hardware Bag
More informationBath Accessory Installation
Bath Accessory Installation Step 1 - Clean surface using a clean dry cloth or use rubbing alcohol to remove any residue (wax, grease, solvents). Allow to dry one hour. Caution! DO NOT use any household
More informationTOYOTA Tundra 2014 Fender Flare Set
2014 Part Number: 00016-34047 Accessory Code: TG1 Conflicts Note: Regular Cab Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right Front Fender Flare 3 1 Left Rear Fender
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationRadon 07 Installation Instructions & Parts List
Radon 07 Installation Instructions & Parts List Illustration Radon 07, H1 Handle Right Hand: Open Out 14/06/2016 Revision 1.1 Page 1 of 21 IMPORTANT This shower screen / enclosure must be installed by
More informationSimply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware.
2 Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware. Apply masking tape to the top of the bumper cover underneath
More information2018+ Mustang Corner Pockets Installation Instructions P/N: (R B972)
2018+ Mustang Corner Pockets Installation Instructions D 02 RA -1 F 9- T 18 P/N: 422083 (R1318-16B972) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2018+ Mustang Corner Pockets Installation Instructions
More informationDubnium 11 Installation Instructions & Parts List
Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationUPPER DOOR KIT P/N APPLICATION BEFORE YOU BEGIN ITEMS MARKED (*) ARE INCLUDED IN HARDWARE KIT PN P/N Rev 01 07/14 Page 1 of 6
UPPER DOOR KIT P/N 2880609 APPLICATION RZR 900 BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for
More information4-COLUMN CURVED CORNER RACKS WITH HIGH REVEAL DISPLAY ROW
Wine Rack Assembly Instructions 4-COLUMN CURVED CORNER RACKS WITH HIGH REVEAL DISPLAY ROW Classic Estate Congratulations! You have purchased the finest wine racking available anywhere. Properly assembled,
More informationtile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 3000 Door-Door Header, sliding doors RDQCI5301
More informationArgon 02 Installation Instructions & Parts List
Argon 02 Installation Instructions & Parts List Illustration Argon, H1 Handle Right Hand: Open Out 16/06/2016 Revision 1.1 Page 1 of 10 IMPORTANT This shower screen / enclosure must be installed by suitably
More informationXenon 05 Installation Instructions & Parts List
Xenon 05 Installation Instructions & Parts List Illustration Xenon 05, H1 Handle Left Hand: Open Out 26/05/2016 Revision 2.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed by suitably
More informationVALENCIA CORNER DOOR WITH RETURN
VALENCIA CORNER DOOR WITH RETURN INSTALLATION GUIDE SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: ( not supplied) Sika Silaflex NG To seal the WHITE shower door and returns to the shower tray. Usage:
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS LUGGAGE NET P/N 08L96-TL2-200 2009 TSX BII 38592-39370 Issue Date APRIL 2008 PARTS LIST 2 6 x 20 mm Hex bolts Luggage net 2 6 x 16 mm Hex
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationSignal Mirror Installation Instructions Dodge Charger, Dodge Magnum, Chrysler 300
Signal Mirror Installation Instructions 2006-2009 Dodge Charger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300 THE safety accessory of the 21st Century. P/N 210-0123-0 Rev. A4 (10/7/09), BTV 2007 Muth
More informationHURST COMP STICK KIT DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog # & by Hurst Performance
HURST COMP STICK KIT 2005-2007 DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog #538 0410 & 538 0411 2009 by Hurst Performance FORM 159 0410 03/09 Thank you for purchasing the Hurst Comp
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 6334 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,
More informationRLZ-02 - Rear Cross Bar, Ford Transit Connect.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationDeauville Installation Guide
vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before
More informationFORD RANGER 1 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
FORD RANGER PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these instructions
More informationLOCKN LOAD FIRST TIME INSTALLATION
LOCKN LOAD TM TRACK MOUNTING KIT NISSAN NAVARA D40 2004-2015 2 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST
More informationFrameless Bypass Slider
INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationJeep Wrangler JK & 4-Door Front Pair Part # Revision H
Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with
More informationTOYOTA TUNDRA 2007>> FENDER FLARE SET
TOYOTA TUNDRA 2007>> FENDER FLARE SET Section I Installation Preparation Part Number: 00012-T0852- & 00012-T1052- Section I Installation Preparation Kit Contents Color Applicability/Trim Level Item Quantity
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK004 / KRJW016T INSTALL TIME: 2 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationProduct Care & Maintenance Guide
Product Care & Maintenance Guide To prolong the life and beauty of your new cabinetry, please read and follow these product care and maintenance instructions. While 6 Square takes great care in building
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More information*Patent Pending. *Trademarked. Series II. Glass Conversion Kit. (888) One-Products (888)
*Patent Pending *Trademarked Series II Glass Conversion Kit www.onepieceproducts.com (888) One-Products (888) 663-7763 Installation Manual Full One Piece Door Glass Conversion Kit Series II 1967-1972 Chevy
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationSCION tc 2005 PEDESTAL SPOILER Preparation. Part Number: PT47A XX PT47A XX PT47A XX
Preparation Part Number: PT47A-21052-XX PT47A-21062-XX PT47A-21082-XX Kit Contents Item # Quantity Reqd. Description 1 1 Painted Spoiler Assembly 2 1 LH Gas Strut 3 1 RH Gas Strut 4 1 Hardware Bag Hardware
More informationG. H. I. N. J. O. 22"x 28" Poster Holder. P. Q. romotional wall displ
Wall Display Assembly Instructions Tools necessary for assembly 1. Electric drill with Phillips head 2. Adjustable wrench or pliers 3. One or two step ladders or stools Due to the weight of the side panels
More information968 Side Cladding Rubber Beading Replacement
968 Side Cladding Rubber Beading Replacement A common and simple wear-oriented project for the 968 is the replacement of the rubber seals or beading on the lower side body cladding. These seals become
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 7646 & 766 For GMC Sierra 500 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationVALENCIA RONDO DOOR WITH RETURN
VALENCIA RONDO DOOR WITH RETURN INSTALLATION GUIDE SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: ( not supplied) Sika Silaflex NG To seal the WHITE shower door and returns to the shower tray. Usage:
More informationDeauville Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions
More informationINSTALLATION & OWNER S MANUAL
Rev. O p. 1 of 16 INSTALLATION & OWNER S MANUAL V4213 BALL CAGE KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationInstallation instructions, accessories. Rails. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No
Instruction No Version Part. No. 8685942 1.0 Rails J8401014 Page 1 / 9 Equipment A0000162 A0000161 J8401006 Page 2 / 9 INTRODUCTION Read through all of the instructions before starting installation. Notifications
More informationLED Thin Frame Fixed Frame Screen User Guide
LED Thin Frame Fixed Frame Screen User Guide INTRODUCTION INTRODUCTION WARNING - Sharp Edges This product may contain sharp edges, please handle with care. Protective gloves are recommended. WARNING -
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS UltraHD Locker Gear Cabinet (Model No. 16221) 18in. W X 24in. D X 72in. H (45.72cm x 60.9 cm x 1.83 m) Reference page 10 for special care and maintenance of stainless steel TR160711
More informationCut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFender Protectors. To ensure a successful installation, please read all of these instructions prior to starting.
Fender Protectors To ensure a successful installation, please read all of these instructions prior to starting. General Instructions All Tough Stuff Protective Products use a waterproof contact adhesive.
More informationIMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
SAPPHIRE ALCOVE SHOWER INSTALLATION GUIDE IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION SHOWER WALL TOP RAIL DOOR RETAINER DOOR RETAINER DOOR ASSEMBLY DOOR SILL SHOWER TRAY
More informationIncluded in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationPART NUMBER: T-R20 PACKAGE CONTENTS: GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Scuff Plate TOOLS REQUIRED: APPLICABLE MODELS: 2013 MAZDA CX-
PART NUMBER: 0000-8T-R20 PACKAGE CONTENTS: GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TOOLS REQUIRED: APPLICABLE MODELS: 2013 MAZDA CX-5 FRONT SCUFF PLATE (Qty 2) 50% ISOPROPYL ALCOHOL/RESIDUE FREE
More informationJeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More information