INSTALLATION INSTRUCTIONS
|
|
- Clyde Wood
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2011 MDX Publications No. BII Issue Date AUG 2010 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket B-L Left rear fender trim Bracket A-R Left rear bumper trim Right front fender trim Bracket B-R Right front bumper trim 2 Self-tapping screws, 5 x 20 mm Right rear fender trim 2 Spring nuts Right rear bumper trim 6 Expansion clips 2 Self-tapping screws, 5 x 12 mm 2010 American Honda Motor Co., Inc. All Rights Reserved. BII (1008) 08P21-STX-2A of 8
2 4 Black films Installing the Left Front Bumper Trim 1. Remove the self-tapping screw from the front bumper. 10 Alcohol swabs Alcohol swab information TOOLS AND SUPPLIES REQUIRED Stubby Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Masking tape Tape measure Rubber roller (T/N MHLE54D) SCREW (Reuse.) AR 2. Using an alcohol swab, thoroughly clean the area where the left front bumper trim will attach. ATTACHMENT POSITION (Clean with the alcohol swab.) INSTALLATION Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be careful not to damage the painted surfaces of the body when installing the fender trim This fender trim kit should be installed only if the ambient air temperature is 15 C (60 F) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours. These instructions show the left fender trim pieces being installed; the same procedure applies to installing the right fender trim pieces. This fender trim kit cannot be installed on a vehicle equipped with a full nose mask. DIMPLE MARK SPRING NUT AR 3. Locate the dimple mark on the front bumper. Slide a spring nut over the dimple mark. 2 of 8 BII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
3 4. Peel back 25 mm (1 in.) of the adhesive backing, and attach it to the front of the left front bumper trim with masking tape. Remove the small piece of adhesive backing from the left front bumper trim. 6. Slowly and carefully peel the adhesive backing from the left front bumper trim. After removing the adhesive backing, press the left front bumper trim firmly against the front bumper with the palms of your hands for 30 seconds, particularly at the edges. SMALL PIECE OF ADHESIVE BACKING (Slowly peel away.) (Peel back 25 mm (1 in.) of adhesive backing, and tape it to the front of the left front bumper trim.) AR 5. Position the left front bumper trim on the front bumper, and align it with the top edge of the front bumper. Install one self-tapping screw and one 5 x 20 mm self-tapping screw through the left front bumper trim, but do not tighten them yet. 2 SCREWS (Tighten.) 7. Tighten the two self-tapping screws installed in step 5. Installing the Left Front Fender Trim 8. Turn the steering wheel fully counterclockwise AR ATTACHMENT POSITION (Clean with an alcohol swab.) Align with the top edge of the front bumper. INNER 3 SELF- TAPPING SCREWS (Loosen.) SCREW (Reuse: Do not tighten.) 5 x 20 mm SCREW (Do not tighten.) AR 2 EXPANSION CLIPS (Discard.) Left side only BR 9. Remove the two expansion clips that fasten the left front inner fender, and loosen the three self-tapping screws that fasten the left front splash guard. 10. Using an alcohol swab, thoroughly clean the area where the left front fender trim will attach American Honda Motor Co., Inc. All Rights Reserved. BII (1008) 3 of 8
4 11. Using an alcohol swab, thoroughly clean the area where the black film will attach. ATTACHMENT POSITION (Clean with an alcohol swab.) 2 mm (0.08 in.) 14. Peel back 25 mm (1 in.) of the adhesive backings, and attach them to the front of the left front fender trim with masking tape. Remove the small piece of adhesive backing from the left front fender trim. SMALL PIECE OF ADHESIVE BACKING 2 S (Peel back 25 mm (1 in.) of adhesive backing, and tape it to the front of the left front fender trim.) BLACK FILM AR 12. Remove the adhesive backing from the black film. Pull the top of the left front splash guard out toward you, and attach the black film at the indicated position. 13. While holding the left front splash guard against the left front inner fender, tighten the self-tapping screws in the order shown. INNER 15. Position the left front fender trim on the left front fender, and align it with the front edge of the left front fender. Install two new expansion clips through the left front fender trim AR 3 2 Left side only. 1 3 SCREWS 2 NEW EXPANSION CLIPS AR Align with the front edge of the left front fender BR 4 of 8 BII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
5 16. Slowly and carefully peel the adhesive backings from the left front fender trim. After removing all of the adhesive backings, press the left front fender trim firmly against the left front fender with the palms of your hands for 30 seconds, particularly at the ends. Installing the Left Rear Bumper Trim 18. Remove the self-tapping screw that fastens the rear bumper to the left fenderwell. ATTACHMENT POSITION (Clean with an alcohol swab.) REAR 2 ADHESIVE BACKINGS (Slowly peel away.) BR 17. Using a rubber roller, apply pressure against the left front bumper trim and left front fender trim, and roll from one end to the other. trim SCREW (Reuse.) 19. Using an alcohol swab, thoroughly clean the area where the left rear bumper trim will attach. 20. Remove the four self-tapping screws and one expansion clip that fasten the left rear splash guard. ATTACHMENT POSITION (Clean with an alcohol swab.) AR 2 mm (0.08 in.) ADHESIVE BACKING BLACK FILM RUBBER ROLLER BR EXPANSION CLIP (Reuse.) 4 SCREWS (Reuse.) AR 21. Using an alcohol swab, thoroughly clean the area where the black film will attach. 22. Remove the adhesive backing from the black film. Pull the top of the left rear splash guard out toward you, and attach the black film at the indicated position American Honda Motor Co., Inc. All Rights Reserved. BII (1008) 5 of 8
6 23. Reinstall the four self-tapping screws. Do not tighten the self-tapping screws yet. INNER 26. Position the left rear bumper trim on the rear bumper, and align it with the top edge of the rear bumper. Install the self-tapping screw through the left rear bumper trim, but do not tighten it yet. 3 Align with the top edge of the rear bumper. REAR 2 4 EXPANSION CLIP (Reuse.) 1 4 SCREWS (Reuse.) AR 24. While holding the left rear splash guard against the left rear inner fender, tighten the self-tapping screws in the order shown. Reinstall the expansion clip. 25. Peel back 25 mm (1 in.) of the adhesive backing, and attach it to the front of the left rear bumper trim with masking tape. Remove the two small pieces of adhesive backing from the left rear bumper trim. SCREW (Reuse: Do not tighten.) REAR AR 27. Slowly and carefully peel the adhesive backing from the left rear bumper trim. After removing the adhesive backing, press the left rear bumper trim firmly against the rear bumper with the palms of your hands for 30 seconds, particularly at the ends. SMALL PIECE OF REAR SMALL PIECE OF ADHESIVE BACKING (Peel back 25 mm (1 in.) of adhesive backing, and tape it to the front of the left rear bumper trim.) AR SCREW (Tighten.) (Slowly peel away.) BR 28. Tighten the self-tapping screw installed in step of 8 BII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
7 Installing the Left Rear Fender Trim 29. Remove the expansion clip and bolt from the left rear inner fender. INNER ATTACHMENT POSITION (Clean with the alcohol swab.) 33. Peel back 25 mm (1 in.) of two adhesive backings, and attach them to the front of the left rear fender trim with masking tape. Remove the two small pieces of adhesive backing from the left rear fender trim. SMALL PIECE OF 2 S (Peel back 25 mm (1 in.) of adhesive backing, and tape it to the front of the left rear fender trim.) SMALL PIECE OF ADHESIVE BACKING BOLT (Reuse.) EXPANSION CLIP (Reuse.) AR 30. Using an alcohol swab, thoroughly clean the area where the left rear fender trim will attach. 31. Use the bolt to install bracket A-L with the tab behind the metal flange, but do not tighten it yet. 34. Position the left rear fender trim on the left rear fender as shown AR BOLT (Reuse: Do not tighten.) trim TAB A-L EXPANSION CLIP (Reuse.) B-L Align with the curved end line of the left rear fender. REAR SECTION VIEW AR AR 32. Install bracket B-L using the expansion clip American Honda Motor Co., Inc. All Rights Reserved. BII (1008) 7 of 8
8 35. Align the hole in bracket A-L with the hole in the left rear fender trim, and tighten the bolt installed in step While pushing up on the left rear fender trim, slowly and carefully peel the adhesive backings from the left rear fender trim. After removing all of the adhesive backings, press the left rear fender trim firmly against the left rear fender with the palms of your hands for 30 seconds, particularly at the edges. BOLT (Tighten.) A-L Align the hole in bracket A-L with the hole in the left rear fender trim AR 36. Install one 5 x 12 mm self-tapping screw and a new expansion clip through the holes in the left rear fender trim and the brackets A-L and B-L. Do not tighten the 5 x 12 mm self-tapping screw yet. 2 S (Slowly peel away.) SCREW (Tighten.) BR 38. Tighten the self-tapping screw installed in step Using a rubber roller, apply pressure against the left rear fender trim and left rear bumper trim, and roll from one end to the other., B-L trim A-L NEW EXPANSION CLIP 5 x 12 mm SCREW (Do not tighten.) BR RUBBER ROLLER trim AR 40. Repeat steps 1 through 39 to install the fender trim on the right side of the vehicle (Turn the steering wheel all the way clockwise in step 8). 8 of 8 BII (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-TK6-100 Application 2013 FIT (BASE MODEL) Publications No. AII 13241 Issue Date JULY 2012 PARTS LIST Right front splash guard TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 30914 UNDER SPOILER 2006 TL Issue Date SEP 2005 PARTS LIST Front under spoiler Template B Left bracket (Marked L) Left cover (Marked
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-TR0-100A Application 2013 CIVIC 4-DOOR Publications No. AII 13081 Issue Date NOV 2012 PARTS LIST 2 Grommets B Left front splash guard 2 Self-tapping screws,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Kit G Coupe 999J2 JxxxxB4 (xxxx Designates model year and color) Item Qty. Description Part Number
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS AERO 2009 TSX BII 39056 Issue Date APRIL 2008 PARTS LIST TOOLS AND SUPPLIES REQUIRED Front aero bumper Phillips screwdriver Flat-tip screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK (BLACK) P/N 08L02-STX-210B Application 2013 MDX Publications No. BII 13434 Issue Date JULY 2012 PARTS LIST Right side rail Right center stay Left side rail
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory P/N 08U35-SZN-200 Application 2012 ZDX Publications No. BII 46578 Issue Date AUG 2011 PARTS LIST 2 Rivet nuts (5 mm) Cargo cover 8 Self-tapping screws, 5 x 50 mm Left base 8 Self-tapping
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2003 ACCORD AII 24040 4-DOOR CARGO NET P/N 08L96-SDA-100 Issue Date AUG 2002 PARTS LIST Cargo net 2 Anchors TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RACK (BLACK) Application 2010 MDX Publications No. BII 42095-43814 Issue Date APRIL 2010 1PARTS LIST Right center stay Right side rail Left side rail Left center
More informationToyota FJ Cruiser 2006-Up Set Part # Revision A
Toyota FJ Cruiser 2006-Up Set Part # 31924 Revision A 03-31-08 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure
More informationFENDER FLARE INSTALLATION
Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationBolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS LUGGAGE NET P/N 08L96-TL2-200 2009 TSX BII 38592-39370 Issue Date APRIL 2008 PARTS LIST 2 6 x 20 mm Hex bolts Luggage net 2 6 x 16 mm Hex
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25829 2004 MDX Issue Date SEP 2003 PARTS LIST Tailgate spoiler Right cover Left cover 2 Flat-head screws 2 Turn nuts TOOLS AND SUPPLIES
More informationConflicts. TOYOTA Highlander 2015 Fender Flares Part Number: Accessory Code: BF7000. Safety Tools Safety Glasses
Highlander 2015 Fender Flares Part Number: 00016-48016 Accessory Code: BF7000 Conflicts Note: Factory Splash Guards Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right
More informationToyota Extend-A-Fender Fender Flares Set of 4
Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:
More informationDodge Dakota 2005 Quad Cab Set Part # Revision A
Dodge Dakota 2005 Quad Cab Set Part # 51908 Revision A 2-17-06 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure
More informationPROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT
AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: REAR SPOILER KIT - CARBON FIBER INFINITI Q60 T99J1 5CH0B KIT CONTENTS: Item Qty. Part Description A 1 Spoiler Assembly B 4
More informationToyota Pocket Style Fender Flares Set of 4
Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationIncluded in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION:
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationRubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs
Jeep Cherokee ZJ Set Part #10916-07 Rev-2 03-11-10 THESE INSTRUCTIONS INVOLVE CUTTING THE FENDERS OF THE VEHICLE. IT IS IMPORTANT TO READ ALL INSTRUCTIONS PRIOR TO THE CUTTING AND INSTALLATION OF THESE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory CARGO NET P/N 08L96-TR0-100 Application 2012 CIVIC 2 AND 4-DOOR Publications No. AII 45607 Issue Date APR 2011 PARTS LIST Accessory User s Information Manual Cargo net
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2010 RIDGELINE Publications No. AII 42145 Issue Date AUG 2009 PARTS LIST Left tube 2 Washers 2 Well nuts Right tube (with
More informationBolt-On/Rugged Fender Flares GMC Sierra 1500/2500/3500 (14-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationRev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-11 QTY 3D PART NO. DESCRIPTION 1 691800 FRONT AIR DAM 1 691802 RIGHT SIDE SKIRT 1 691801 LEFT SIDE SKIRT 1 691804 REAR LOWER SKIRT RIGHT SIDE 1 691803 REAR LOWER SKIRT LEFT SIDE 4 3M 94 3M ADHESION
More informationGMC Extend-A-Fender Fender Flares Set of 4
GMC Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S AND CROSS BARS Application 2009 PILOT Publications No. AII 39407 Issue Date MAY 2008 PARTS LIST 4 Roof molding clips Left side roof rack TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationBolt-On/Rugged Fender Flares Toyota Tundra (14-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY Extrusion 28.0 ft Short Screw 18 Nuts 42 Alcohol Wipe 4 Long
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit :
Jeep Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFord F150 Rear Flares Set Part # Revision
Ford F150 Rear Flares Set Part # 20074 Revision 1 04-01-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.
More information2015 GMC Yukon. Upper Class Grille Insert
Upper Class Grille Insert TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationIncluded in Hardware Kit: Toyota Tacoma, Regular/Access/Double Cab, Shortbed Set Part # Rev STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFENDER FLARE INSTALLATION
TG-FF8T4178: Fit 2014-UP Toyota Tundra PRIOR TO INSTALLATION IMPORTANT Tyger only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation
More informationToyota Pocket Style Fender Flares Front Pair
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationBolt-On/Rugged Fender Flares Chevy CK PICKUP (88-98) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 25ft SMALL CLIPS 14 ALLEN KEY BOLT 42 ALCOHOL TOWELETTE 4 SCREWS
More informationToyota Pocket Style Fender Flares Front Pair
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Running Boards Kit Nissan Pathfinder/ Infiniti QX60 999T6 X5060 (Pathfinder Running Board Kit) 999T6 R5060 (Infiniti QX60
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2011 RIDGELINE Publications No. AII 43440 Issue Date JUNE 2010 PARTS LIST Left tube 6 Hex bolts Right tube (with label)
More informationFENDER FLARE INSTALLATION
: 2009 - UP Ram 1500 Fleetside. (Exclude R/T Models) Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife PRIOR TO INSTALLATION Hardware Kit Included 5/16
More informationJeep Wrangler JK & 4-Door Front Pair Part # Revision H
Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with
More informationIncluded in Hardware Kit. 09-Up Ford F150. Set Part # Rev STEP 1 - PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION:
09-Up Ford F150 Set Part #20927-02 Rev-3 5-18-09 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More informationFENDER FLARE INSTALLATION
: 2011-2014 Ram 2500/3500 Fleetside 76.3 inch and 98.3 inch Bed. Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife 6. Awl or Similar Pointed Tool PRIOR
More informationGMC Extend-A-Fender Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory MOON P/N 08R01-TR0-100 Application 2013 CIVIC 4-DOOR Publications No. AII 13080 Issue Date NOV 2012 Put this information in the glove box with the vehicle owner s manual.
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationToyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION
Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION Front Part #30922-02 Rev-1 7/18/2016 A) Bushwacker only approves installing the flares according to these written instructions with
More informationJeep Wrangler JK Door Rear Pair Part # Revision E
Jeep Wrangler JK 2007 4-Door Rear Pair Part # 10044 Revision E 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the
More informationChevrolet Pocket Style Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationToyota Pocket Style Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationChevy Pocket Style Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationGRIP Mustang GT/V6 Body Kit
GRIP Mustang GT/V6 Body Kit GRIP highly recommends that our kits be installed by professionals with experience installing automotive aftermarket parts and accessories. However, we do recognize that many
More informationJeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFord Max Pocket Style Fender Flares Set of 4
Ford Max Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFENDER FLARE INSTALLATION
Part#: TG-FF8G4158 FOR 2007-2013 GMC Sierra 1500 Pickup Truck (Exclude 69.3inch Short Bed Models) FENDER FLARE INSTALLATION Hardware Kit Included IMPORTANT TYGER only approves the installation according
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationTOYOTA TUNDRA 2015 BLACK TEXTURED FENDER FLARE
TOYOTA TUNDRA 2015 BLACK TEXTURED FENDER FLARE Part Number: 00016-34083-02 Accessory Code: BF1000 Conflicts Note: Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right Front
More informationC70 Window Roller Repair Taken from: Heres the problem:
C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70
More informationFlat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationCut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationToyota Tacoma Extended Cab/Standard Cab Set Part # Rev
Toyota Tacoma Extended Cab/Standard Cab Set Part # 31919 Rev-7 06-23-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the
More informationJeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationRAM Pocket Style Fender Flares Set of 2 (Rear)
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFord Pocket Style Fender Flares Set of 4
Ford Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AE Last Updated: 09/08/14 US PATENTS: D683281, D CHINESE PATENT: ZL
PREMIUM FRONT BUMPER US PATENTS: D683281, D697842 CHINESE PATENT: ZL 2012 3 0026081.4 AEV30103AE Last Updated: 09/08/14 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION,
More informationFENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED
` FENDER FLARE Part No: FFD3001S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required
More informationIncluded in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationToyota Extend-A-Fender Fender Flares Set of 4
Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:
More informationIncluded in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Rear Pair
A) B) C) D) E) F) G) H) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Rear Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationJeep Cherokee Door XJ Set Part # Revision J
Jeep Cherokee 84-96 4 Door XJ Set Part # 10911 Revision J 6-5-06 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure
More information1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs
97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with
More informationRAM Pocket Style Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFord Pocket Style Fender Flares Set of 4
Ford Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationRAM OE Style Fender Flares Set of 4
RAM OE Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationAll Terrain Flares 09+ Ford F150
Page 1/5 Components: 1. Front Flares (2) 2. Front Flare Inner Pieces (2) 3. Rear Flares (2) Tools required: - Utility knife - Electric Drill - 1/4 Drill Bit - #2 Phillips driver - Socket wrench Hardware
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFord Cut-Out Fender Flares Front Pair
Ford Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFord Pocket Style Fender Flares Set of 4
Ford Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION Set Part #20942-02 Rev-4 07/05/2018 A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ROOF RAILS P/N 08L02-TX4-200 Application 2018 RDX Publications No. VERSION 1 Issue Date MAY 2017 PARTS LIST Right center stay Roof left rail Left center stay Roof right
More information2011 KIA Optima SX / EX Turbo Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED 2011 KIA Optima SX / EX Turbo Mesh Grille Upper and Lower Overlay Part #: Complete 1310-0102-11SX / Black Ice Part #1310-B102-11SX
More informationBolt-On/Rugged Fender Flares Ford F150 (15-ON) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29ft RETAINING CLIP 4 ALLEN KEY BOLT 42 ALCOHOL TOWELETTE 4
More informationGRIP Scion tc Body Kit
GRIP Scion tc Body Kit GRIP highly recommends that our kits be installed by professionals with experience installing automotive aftermarket parts and accessories. However, we do recognize that many customers
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationJeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFRONT BUMPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
FRONT BUMPER KIT P/N 2882301 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationJK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS
JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationFord Pocket Style Fender Flares Set of 4
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationIncluded in Hardware Kit 4. Toyota Tundra, B- & D-Cab, CrewMax. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to
More informationTYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side
TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS
More information