Northcote Corner Base Unit & Top Shelf L2504

Transcription

1 Thank you for shopping with LT, we hope you enjoy having this product in your home. Northcote orner ase Unit & Top Shelf L2504 We know assembling furniture, toys or accessories is not everyone s favourite way to spend their time, so we ve tried to make assembling this item as quick and painless as possible. Hopefully our efforts will have been worthwhile and you ll sail through the whole process. ut if it all feels a bit too much like hard work, then we do have an assembly company we can recommend: the Flatpack onstruction ompany offers a nationwide service and can be contacted on or www. flatpackconstruction.co.uk. A few important pointers before you start: Please read the instructions right through before you start, and check that all the components have been included in the pack; we find separating all the hardware into piles makes it easier to be sure that everything is present and correct. Make sure you have the right tools. Allen keys are provided if required, but screw drivers and other tools are not. You ll find details of the tools you need at the beginning of the instructions. It s a good idea to build the unit in the room where you are going to be using it, to avoid the need to move it after it s been assembled. Do not throw away any packing materials until assembly is complete, just in case you accidentally discard smaller parts and hardware. Assembly Difficulty easy - medium - hard two-person job 24/01/2017 V2 1

2 Safety Warnings: Anti-tip furniture straps are recommended for use on the Northcote range. Anti-tip furniture straps (5323) are available from gltc.co.uk. It is recommended that the Northcote modular storage furniture is only stacked 3 units high, inclusive of the base unit..g. 1 x ase unit + 2 x Shelf units Adult assembly required. 2 person assembly recommended. Assemble and use on a flat surface. HOKIN HAZARD This product contains small parts and must be assembled by an adult. Special care should be taken in the unpacking and assembly of this item as unassembled parts may be a choking hazard to children under 3 years old. During assembly, children should be kept away from the product due to possible risk of injury. Do not use power tools in the construction of this product. This product is heavy, so we recommend that you build it where you are planning to use it. All assembly fastenings should be tightened properly and periodically checked; care should be taken that no fittings are loose. Keep all relevant information for future reference. ustomer Service: If you find that any components are missing or damaged, please do not begin assembly and do not use the item. Please contact LT ustomer Services on immediately. We do stock spare hardware packs at our warehouse, so we should be able to send you a replacement pack immediately if required. Product are: Wipe clean using a soft damp cloth followed by a dry cloth. Do NOT use cleaning products which may contain ammonia, solvents or abrasive material. Do NOT expose the furniture to extremes of heat and humidity. ould we do better? If there is anything you think could be improved in these instructions or in the assembly of this product we d be grateful if you could let us know; we ll pass any helpful hints and tips on to other customers via our website and update the instructions. All you need to do is drop us a line at instructions@gltc.co.uk Thank you 2

3 omponent heck List: orner ase Unit omponent heck List: All Hardware You will need: (not supplied) 30x am Dowels 45mmL 30x am Locks 14mmDia A ase - Sides (x2) ase - ase Panels left & right 31x Wooden Dowels 20mmL Philips Head Screwdriver Flat Head Screwdriver ase - ack orner ars omponent heck List: orner Top Shelf D ase - ack Panels H Shelf - ack (x2) Please note one is longer ase - Top Panels left & right F ase - Front ars Please note one is longer Shelf - ase (x2) left & right I Shelf - Sides (x2) left & right 3

4 Assembly: ase Unit STP 1: nsure that each cam lock s arrow is pointing towards the drill hole on the side edge of the component. When in position, turn the 3 x cam locks () on the base panel () clockwise to lock in place. Hardware for Step 1: Lay both base panels () on a clean flat surface with the large drill holes facing up. 3x am Dowels 2x Wooden Dowels Insert 2 x cam dowels () and 2 x wooden dowels () into the diagonal edge of the left hand base panel (). The wooden dowels go into the larger holes. Insert 1 x cam dowel () into the diagonal edge of the right hand base panel (). N: Wooden dowels should fit snuggly and push in with your fingers. Do not use force or a hammer as the wood may split. Hardware for Step 2: 3x am Locks STP 2: Push the two base panels () together. Insert 3 x cam locks () into the large drill holes along the edge of the joined components. The arrows should point towards the connecting edge of the base panel (). Turn all of the cam locks () clockwise to lock. 4

5 Assembly: ase Unit STP 4: Hardware for Step 3: 2x am Dowels 2x Wooden Dowels Slide the thinner back corner bar () onto the hardware on the left hand side, making sure the side groove lines up with that on the base panel (). Also make sure the large drill hole is facing backwards. Repeat the process with the wider back corner bar (), placing it on the right hand side, lining up the grooves and ensuring the large drill hole is facing backwards. Thin Part Wide Part Hardware for Step 5: 2x am Locks Thin Part Wide Part STP 5: Insert 2 x cam locks into the large drill holes on the back of the back corner bars (), with the arrows facing down and turn clockwise to lock. STP 3: Turn the joined base panel () over. Insert 2 x cam dowels () and 2 x wooden dowels () into the holes at the back point of the base panel () as shown. When in position, turn the 2 x cam locks () clockwise to lock in place. 5

6 Assembly: ase Unit nsure that each cam lock s arrow is pointing towards the drill hole on the side edge of the component. When in position, turn the 3 x cam locks () on the top panel () clockwise to lock in place. Hardware for Step 6: STP 6: 3x am Dowels 2x Wooden Dowels Take the two top panels () and lay them on a clean flat surface, with the grooves and large drill holes facing up. Insert 2 x cam dowels () and 2 x wooden dowels () into the diagonal edge of the left hand top panel (). The wooden dowels go into the larger holes. Insert 1 x cam dowel () into the diagonal edge of the right hand top panel (). Hardware for Step 7: 3x am Locks STP 7: Push the two panels () together. Insert 3 x cam locks () into the large drill holes along the edge of the joined components. The arrows should point towards the connecting edge in the top panel. Turn all of the cam locks () clockwise to lock. 6

7 Assembly: ase Unit Hardware for Step 8: 2x am Dowels 2x Wooden Dowels two-person job Hardware for Step 10: 2x am Locks STP 8: Insert 2 x cam dowels () and 2 x wooden dowels () into the holes at the back point of the top panel () as shown. STP 9: Position the joined base panels ( & ) on its side, as shown. Wide Part Thin Part Turn the 2 x cam locks () on the back corner bars () clockwise to lock in place. STP 10: Attach the joined top panel () to the back corner bars (). Insert 2 x cam locks into the two remaining large drill holes on the back of the two corner bars (), with the arrows facing towards top panel () and turn clockwise to lock. 7

8 Assembly: ase Unit STP 11: Slide one of the back panels (D) into the inside grooves of top panel () and back panel (). STP 13: Push the shorter of the front bars (F) onto the wooden dowel as shown. F D Hardware for Step 12: Hardware for Step 14: 2x Wooden Dowels STP 12: Insert 2 x wooden dowels () into the front corner of the base panel (). 5x am Dowels 5x Wooden Dowels A left side STP 14: Insert 5 x cam dowels () and 5 x wooden dowels () into the left side panel (A). The wooden dowels go into the larger holes. 8

9 Assembly: ase Unit Hardware for Step 15: STP 16: Slide the second back panel (D) into the grooves on the other side of the unit. D 4x am Locks F A left side STP 17: Push the longer of the front bars (F) onto the remaining wooden dowel in the front corner of the base panel (). F STP 15: Place the left side panel (A) onto the top, bottom and front bar panels (, & F) as shown, making sure the groove lines up with the back panel and the teeth are facing upwards. Insert 5 x cam locks into large drill holes. There are two on the base panel (), two inside the top panel () and one on the inside of the front bar (F). Turn all these clockwise to lock. Turn the cam locks () on the back of panels, & F clockwise to lock in place. 9

10 Assembly: ase Unit Hardware for Step 14: two-person job 5x am Dowels 5x Wooden Dowels A right side STP 18: Insert 5 x cam dowels () and 5 x wooden dowels () into the right side panel (A). The wooden dowels go into the larger holes. Hardware for Step 19: A 5x am Locks STP 19: Place the right side panel (A) onto the top, base and front bar panels (, & F) as shown, making sure the groove lines up with the back panel and the teeth are facing upwards. Insert 5 x cam locks into large drill holes. There are two on the base panel (F), two inside on the top panel () and one on the inside of the front bar (F). Turn all these clockwise to lock. STP 20: Turn the unit upright your base unit is now ready 10

11 Assembly: Top Shelf Unit Hardware for Step 21: Hardware for Step 22: 3x am Dowels 3x am Locks 2x Wooden Dowels nsure that each cam lock s arrow is pointing towards the drill hole on the side edge of the component. When in position, turn the 3 x cam locks () on the base panel () clockwise to lock in place. STP 21: Lay both base panels of the shelf () on a clean flat surface with the large drill holes facing up. Insert 2 x cam dowels () and 2 x wooden dowels () into the diagonal edge of the left hand base panel () and 1 x cam dowel () into the diagonal edge of the right hand base panel () as shown. STP 22: Push the two base panels () together. Insert 3 x cam locks () into the large drill holes along the edge of the joined components. The arrows should point toward the connecting edge in the base panel. Turn all of the cam locks () clockwise to lock. 11

12 Assembly: Top Shelf Unit Hardware for Step 23: Hardware for Step 24: 2x am Dowels 2x Wooden Dowels 1x am Locks H shorter H longer H longer STP 23: Insert one cam dowel () and one wooden dowel () into the end of the longer back bar (H). STP 24: Attach the shorter back bar (H) onto the longer back bar (H) using the hardware just inserted. Insert 1x cam bolt () into the large drill hole at the corner, making sure the arrow is pointing towards the corner. Then turn the cambolt clockwise to tighten. 12

13 Assembly: Top Shelf Unit Hardware for Step 25: Hardware for Step 27: 2x Wooden Dowels 3x am Dowels 3x Wooden Dowels STP 25: Turn the joined base panel () over. Insert 2 x wooden dowels () into the holes at the back point of the base panel (). I left H STP 26: Attach the back bar (H) onto the base panel () by guiding the holes onto the wooden dowels. STP 27: Insert 3 x cam dowels () and 3 x wooden dowels () into the left side panel (I). Insert the wooden dowels into the large drill holes. 13

14 Assembly: Top Shelf Unit Hardware for Step 28: Hardware for Step 29: 3x am Locks 3x am Dowels H 3x Wooden Dowels I left I right nsure that each cam lock s arrow is pointing towards the drill hole on the side edge of the component. When in position, turn the 3 x cam locks () on the panels & H clockwise to lock in place. STP 28: Place the left hand side panel (I) onto the shelf guiding the hardware into the drilled holes, making sure that the two teeth of the panel are facing downwards. Insert 2 x cam locks () into the base panel () with the arrows facing towards the side panel (I). Insert 1 x cam lock () into the back of the back panel (H), with the arrow facing the side panel. Turn all three cam locks clockwise to lock. STP 29: Insert 3 x cam dowels () and 3 x wooden dowels () into the right side panel (I). Insert the wooden dowels into the large drill holes. 14

15 Assembly: Top Shelf Unit Hardware for Step 30: two-person job 3x am Locks H I right STP 30: Place the right hand side panel (I) onto the shelf guiding the hardware into the drill holes, making sure that the two teeth of the panel are facing downwards. Insert 2 x cam locks () into the base panel () with the arrows facing towards the side panel (I). Insert 1 x cam lock () into the back of the back panel (H), with the arrow facing the side panel. Turn all three cam locks clockwide to lock. STP 31: Turn your shelf upright and slot it onto your base unit. 15 oth pieces can now be used together. We recommend the use of one or two Northcote orner Shelf Unit/s (L2505) in between the base unit and the top shelf. opyright 2012.L.T.. Ltd. All rights reserved. reat Little Trading ompany and LT are registered trade marks of.l.t.. Limited.