Charlotte Dressing Table & Stool Set L4294

Transcription

1 Thank you for shopping with GLTC, we hope you enjoy having this product in your home. We know assembling furniture, toys or accessories is not everyone s favourite way to spend their time, so we ve tried to make assembling this item as quick and painless as possible. Charlotte Dressing Table & Stool Set L4294 Hopefully our efforts will have been worthwhile and you ll sail through the whole process. But if it all feels a bit too much like hard work, then we do have an assembly company we can recommend: the Flatpack Construction Company offers a nationwide service and can be contacted on or A few important pointers before you start: Please read the instructions right through before you start, and check that all the components have been included in the pack; we find separating all the hardware into piles makes it easier to be sure that everything is present and correct. Make sure you have the right tools. Allen keys are provided if required, but screw drivers and other tools are not. You ll find details of the tools you need at the beginning of the instructions. It s a good idea to build the unit in the room where you are going to be using it, to avoid the need to move it after it s been assembled. Do not throw away any packing materials until assembly is complete, just in case you accidentally discard smaller parts or hardware. Assembly Difficulty easy - medium - hard two-person job V1 03/06/2017 1

2 Safety Warnings: Adult assembly required. Unassembled product contains small parts which may present a choking hazard. Children should be kept away from the product during assembly to avoid any possible of injury. DO NOT use power tools in the assembly of this product as there is a risk of over-tightening and consequently splitting of the wood. Check all fixtures and fittings regularly and tighten as necessary. Please retain these instructions for future reference. Assemble and use on a flat and level surface. Customer Service: If you find that any components are missing or damaged, please do not begin assembly and do not use the item. Please contact GLTC Customer Services on immediately. We do stock spare hardware packs at our warehouse, so we should be able to send you a replacement pack immediately if required. Product Care: Wipe clean using a soft damp cloth followed by a dry cloth. Do NOT use cleaning products which contain ammonia, solvents or abrasive material. Do NOT expose the item to extremes of heat and humidity. Could we do better? If there is anything you think could be improved in these instructions or in the assembly of this product we d be grateful if you could let us know; we ll pass any helpful hints and tips on to other customers via our website and update the instructions. All you need to do is drop us a line at instructions@gltc.co.uk Thank you 2

3 Component Check List Component Check List A B I J 2x C D K L 2x E F M N 2x 2x G H O P 2x 2x 2x 3

4 Component Check List Component Check List Q R x 42 Cam Dowels 35mm x 42 Cam Locks 14mm #3 #4 S T x 6 Wooden Dowels 25mm x 2 Drawer Stops #5 #6 2x x 2 Screws 10mm #7 #8 x 1 Allen Key U V x 2 Cross Head Bolt 23mm x 2 Drawer Handles #9 0 4x x 8 Screws 25mm x 2 Bolt 66mm 1 2 x 2 Barrel Nuts 10mm x 4 Small Washers 3 4 x 2 Spacers x 2 Bolts 34mm 4

5 Component Check List Assembly: 5 6 x 4 Hinges x 16 Screws 15mm 7 8 x 8 Large Washers x 8 Bolts 42mm A B Hardware for Step 1: 5 STEP 1: Insert 6x Cam Dowels () to panels A and B securing with a Philips Screwdriver. 6x Cam Dowels

6 Hardware for Step 3: 4x Cam Locks C B C B E A D A Hardware for Step 2: STEP 2: Slot panel C in between panels A and B ensuring the hardware holes face downwards. Secure with 2x cam locks (). 2x Cam Locks STEP 3: Locate panels D and E and slot to panels A and B as shown. Secure by inserting 4x cam locks () and turn clockwise. 6

7 Hardware for Step 4: Hardware for Step 5: 2x Cam Dowels 2x Cam Locks 2x #3 Wooden Dowels C B E D A F #3 #3 F STEP 4: Insert 2x cam dowels () into panel F where indicated. 7 STEP 5: Insert 2x wooden dowels (#3) into panel F and lower the frame onto the panel, secure with 2x cam locks to panels A and B.

8 Hardware for Step 6: Hardware for Step 7: 4x Cam Dowels 14x Cam Dowels H I G G J J STEP 6: Locate panels G and attach 4x cam dowels () where shown. 8 STEP 7: Locate all the dressing table leg panels H, I and J and arrange as shown. Panels J do not have pilot holes on the top of the legs and need to be at the bottom. Insert 14x cam dowels into the leg panels where shown.

9 Hardware for Step 8: Hardware for Step 9: 8x Cam Locks 10x Cam Locks H I I H G J G J G J G F Ensure that the side with two larger hardware holes is at the top. STEP 8: Slot in both G panels in between the leg panels as shown. Secure using 4x cam locks () in the corners of both panels G. 9 STEP 9: Slot the side panels (G) to the main frame one side at a time ensuring that the leg panels are in the correct sequence. Secure with 10x cam locks () where indicated.

10 Hardware for Step 10: Hardware for Step 11: 8x Cam Dowels 8x Cam Locks 4x #3 Wooden Dowels #6 Allen Key 2x #4 Drawer Stops I 2x #5 Screws 10mm K #4 J H G C F B #4 #3 #5 #3 #3 #5 #3 STEP 10: Insert 8x cam dowels () and 4x wooden dowels (#3) into top panel K where indicated. Then take 2x plastic drawer stops (#4) and and place where shown with the curved edge facing up towards the large bolt holes which go through the top panel (K), secure using 2x 10mm screws (#5). 10 STEP 11: Insert 8x cam locks () into the hardware holes on the inside of the drawer recesses. Slot Top Panel K onto the base unit ensuring that the drawer stops are nearest leg panels H and I. Using the double ended allen key (#6), with the the pointed end secure the cam locks inside the drawer recesses.

11 Hardware for Step 13: 8x Cam Dowels 2x #7 Cross Head Bolts K #8 2x #8 Drawer Handles (23mm) L #7 STEP 12: Stand up the table ready to attach the drawers and mirrors. 11 STEP 13: Locate the two L panels and insert 4x cam dowels () where indicated on both panels. Then attach the drawer handle (#8) using Cross Head Bolt 23mm (#7) on both panels.

12 Hardware for Step 14: Hardware for Step 15: 8x #9 Screws 25mm 8x Cam Locks #9 #9 M O #9 M #9 N P N O Ensure that the larger hardware holes are at the front and that the smaller pilot holes are at the back L STEP 14: Locate panels N, M and O and slot in the drawer base panel (P) so that it slots into the grooves. Secure using 4x screws 25mm (#9). Repeat for second drawer. 12 STEP 15: Insert 4x cam locks () into the front of the drawer then slot in the drawer front panel (L), secure cam locks with Allen Key #6. Repeat for second drawer.

13 Hardware for Step 17: x 0 Bolts 66mm 4x # 12 Small Washers 2x 1 Barrel Nuts 4x 3 Spacers K R Q 2 2 S 0 #6 L L Please ensure holes to attach hinges face outwards STEP 16: Slide in both drawers into the dressing table. 13 STEP 17: Insert 2x barrel nuts (1) into the back of the central mirror panel (Q). Thread bolt 66mm (0) through Panel R then add washer (2), Spacer (3) then another washer (2) before securing this with an allen key (#6). Repeat of the other side to attach panel S.

14 Hardware for Step 18: Hardware for Step 19: 4x # 15 Hinges 2x 4 Bolts 34mm Q 8x 6 Screws 15mm R S 6 Q R S K 6 5 K 4 4 #6 STEP 18: Lower the Mirror (Q) onto the table top so that the divider panels R and S align with the drill holes on the table. Secure these using 2x bolts 34mm (4) from the underside of the table, tightening using an allen key (#6). 14 STEP 19: Using 8x screws 15mm (6) attach 4x hinges (5) to the top and bottom of the divider panels R and S as shown.

15 Hardware for Step 20: Hardware for Step 21: 8x 6 Screws 15mm 8x # 17 Large Washers V 8x # 18 Bolts 42mm T T U V U STEP 20: With the help of a second person attach both side mirrors (T) to the other side of hinges (5) using 8x Screws 15mm (6). Your Dressing Table is now assembled. 15 STEP 21: To assemble the stool locate seat panel (U) and 4x leg panels (V). Attach the legs by threading large washer (7) on to bolt 42mm (8) and securing into the pilot holes using an Allen Key. Repeat this so that each leg is secured with 2x Bolts (8) and 2x Washers (7).

16 STEP 22: Your Dressing Table and Stool are now ready to use. 16 Copyright 2017 G.L.T.C. Ltd. All rights reserved. Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.