ADJUSTING AJACK M41B SCOPE
|
|
- Janice Bennett
- 6 years ago
- Views:
Transcription
1 ADJUSTING AJACK M41B SCOPE I was a bonehead, and managed to delete the previous post on this subject while trying to move it, so here it is again, but this time with pics! All of the elevation adjustments are performed in the elevation turret on the scope body, while the windage adjustments are performed in the scope mount. The windage adjustments are easier, so we will start with that first. CAUTION!!! The windage screws have a small thread (M3X.5) paired with a large head diameter. Consequently, they are VERY easy to overtighten and snap the head off! There are no replacements, so don't break them. I would like to re-emphasize this, they break easy! Gently snug them, don't crank on them! Step I is to remove the mount from the rifle and flip it over so you are looking at the bottom. At the forward end of the dovetail mount area is a large screw, this secures the front ring, and acts as a pivot for the windage adjustments. Loosen this screw a quarter to half turn, there is no reason to remove it. Then replace the mount on the rifle. Pic #1 shows this screw. Picture #1, front ring main screw As stated above, the front ring acts as a pivot for the entire mount. The rear ring mounts into a curved dovetail, and the windage adjustments are accomplished with 2 windage adjustment screws, one on each side. Loosening one screw and tightening the other will slide the dovetail in the desired direction. The curved dovetail is shown in Picture#2, and the windage adjustment screws are shown in picture #3.
2 Picture #2, rear ring curved dovetail Picture #3, windage adjustment screw Once more, the windage adjustment screws have a small diameter thread, and a large diameter head (see pic #4). They are easy to break, and impossible to replace, use caution!
3 Picture #4, windage adjustment screw Adjusting windage Start out at a short range, about 50 yards. Very small adjustments on these screws have dramatic effect at the target. Take a shot, and check to see if the hit is left or right of the bull, don't worry about elevation yet. If your hit is left, loosen the right screw about 1/4 turn, and gently snug the left screw. Shoot again. Keep adjusting until you are centered left/right. Then move out to longer range, as you move out, it will take smaller adjustments to move your point of impact the same amount. Keep fiddling until you are centered at 300 yards. Once you are happy with the windage, remove the mount from the rifle, and retighten the front ring main screw. NOTE: you should be using high quality, uniform ammo, such as Swede milsurp m94/41 prickskytte, or high quality handloads. Once you have it sighted in, stick to that ammo, and that ammo only! This is a fine instrument, and deserves only the very best ammo. Don't waste your barrel on junk ammo! Curio and Relic Firearms Forum, Swedish Rifles page Edited by: bear8mm at: 9/14/03 1:47 pm
4 ELEVATION ADJUSTMENT MINOR ADJUSTMENT If your point of impact is only a few inches off, use this method. If your adjustment is bottomed out and you are still hitting high, use the MAJOR ADJUSTMENT method. Pick a known range to zero. (The scope increments are in meters, 100 meters=109 yards). Loosen the range dial lock screw (Pic #1) and adjust the elevation knob until you are hitting at zero elevation at a given range (ignoring what the elevation reading is). When you are satisfied with the zero, lock down the thumbscrew. Then loosen (but do not remove) the 2 small screws on the plate at the top of the elevation knob. It will now be possible to rotate the outer range dial (not the knob) until the number lines up at whatever range you are shooting. Hold the range dial in this position while you retighten the 2 small screws. The Swedish Army manual states that the scope is to be zeroed at 300 meters (327 yards). This is approximate mid-range on the scope, and may cause a slight deviation at short or long range. Picture #1, elevation lockscrew
5 Picture #2, elevation cover screws NOTE: These screws are very tiny and made of soft brass (they are not magnetic if you drop one!) Use a proper fitting screwdriver, and DO NOT OVERTIGHTEN! Picture #3, elevation cover screws MAJOR ADJUSTMENTS One of the forum members ed me, and his problem was that with the elevation dialed
6 all the way down, he was still hitting 14" high at 100 yards. These scopes are calibrated for m94/41 prickskytte (sharpshooter) ammo, make sure that is what you are using, or something reasonably close in trajectory. There are actually 2 ways to make major elevation adjustments, I DO NOT KNOW what the preferred method is, but they both work. The simplest (and most scary) method is first. Dial the elevation all the way down, then back off a hair. Remove the 2 tiny screws that hold on the elevation turret cover plate. Lift off the top plate. Underneath is the adjusting knob, there is a large screw in the center, (see pic #4) the 2 small empty holes that the cover screws came out of, further out from center are 2 more holes, only one of these last 2 has a screw installed. (see pics #5 and #6) Picture #4, center adjustment screw
7 Picture #5, "side adjustment screw" Picture #6, empty hole If you need to make a major adjustment downward (or upward) remove the large screw, then carefully lift the entire range knob straight up. It has a square hole in the center. Rotate the knob clockwise 90 degrees (for downward adjustment, counter-clockwise for upward adjustment), then replace the knob on the scope, and put everything back together.
8 The second method is a little more complicated, but is preferable for a "less major" adjustment. With the elevation knob at near bottom of adjustment, loosen the small side screw (pic #5), and unscrew it about halfway. You should then be able to dial the elevation further down, past the previous "stop". Once you are below the previous stop, remove the small screw completely, and replace in the opposite empty hole (pic #6). The screw acts as a stop, and you now have 180 degrees more adjustment than you had before. After either one of these "major" methods is used, you will undoubtedly have to re-zero using the minor adjustment method. If you have not adjusted it enough, either method can be repeated. Curio and Relic Firearms Forum, Swedish Rifles page
SPECIFICATIONS. The WM-6XL Long Wm. Malcolm Telescopic Riflescope Instruction Manual WARNING:
The WM-6XL Long Wm. Malcolm Telescopic Riflescope Instruction Manual SPECIFICATIONS Power: 6X Objective: 17mm Length: 30 in. Weight: 1.85 lb. (29.60 oz.) Eye relief: approx. 4.5 in. Reticle: Fine Crosshair
More informationMOUNTING AND ZEROING RIFLESCOPES FOR SERVICE RIFLE SHOOTING By Marcus O'Dean
MOUNTING AND ZEROING RIFLESCOPES FOR SERVICE RIFLE SHOOTING By Marcus O'Dean Tightening Scope Screws First up, when you tighten any scope-related screws, do so like you would when tightening car wheel
More informationM14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL. West Springfield, MA Phone: (866) FAX: (413)
M14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL Troy Industries, Inc. WWW.TROYIND.COM West Springfield, MA 01089 Phone: (866) 788-6412 FAX: (413) 383-0339 Thank You M14/M1A MODULAR CHASSIS SYSTEM
More informationM14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL. West Springfield, MA Phone: (866) FAX: (413)
M14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL Troy Industries, Inc. WWW.TROYIND.COM West Springfield, MA 01089 Phone: (866) 788-6412 FAX: (413) 383-0339 Thank You M14/M1A MODULAR CHASSIS SYSTEM
More informationVortex. SrikeFire TM. Vortex Optics USA
Vortex SrikeFire TM www.vortexoptics.com Vortex Optics USA 2 VORTEX StrikeFire Red Dot Scope Manual Thank you for your purchase of the Vortex StrikeFire Red Dot scope! We are sure you ll be pleased with
More informationPLEASE READ THIS FIRST!
PLEASE READ THIS FIRST! ADVANCED MICRO RED DOT WITH REMOVABLE BASE SPECIAL PURCHASE / BLEMISH MPN: MD-RB-AD-SP UPC: 8 18500 01273 3 FREQUENTLY ASKED QUESTIONS 1. What makes the MD-RB-AD-SP different from
More informationV-MOTION LITE USER GUIDE. Rat Rig All rights reserved.
V-MOTION LITE USER GUIDE Rat Rig 2017. All rights reserved. PACKAGE CONTENTS 1 1x V-Motion Motor 2 1x Belt 3 1x 3mm Hex Key 4 1x AA Battery Pack (for 8x AA batteries)* 5 1x V-Motion Controller 6 2x Knob
More informationRED DOT #M Sheltered Wings
CROSSFIRE The Crossfire Red Dot Sight The Crossfire with daylight-bright red dot lends itself to a variety of firearm platforms including AR s, shotguns and pistols. The multi-height base offers different
More informationAdjusting Backlash on Sherline handwheels
WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING Adjusting Backlash on Sherline handwheels What Is Backlash? Backlash is the amount the handwheel can turn before
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationAssembly, Use and Care Instructions
Assembly, Use and Care Instructions Product #336677 Instruction #1068318 Rev. F Thank you for purchasing a Caldwell Lead Sled DFT 2. The Lead Sled DFT 2 comes to you partially assembled. It will require
More informationItem # Thanks for shopping with Improvements!
Thanks for shopping with Improvements! Hampshire -Door Cabinet Item #5505 To order, call -800-64- West Chester, OH 45069 Made in China PR-6 If you have questions regarding this product, call -800-64- Mon.-Fri.
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: O-Ring Groove Cutter Adjustable Tool Block Upgrade Page 1 of 5 Prototype Kit Contents: 1x Adjustable Tool Block 1x Adjustable Tool Holder 1x Graduated Adjusting Screw 1x 1/8 Registration
More informationBLUEMOTION UXP, CDP, SD
Feed and Support Kit Contents FEED KIT CONTENTS: - One () 7 Feed Cord - One () 4 Canopy - One () Grommet - One () Threaded Barrel - One () 7 Swedged Suspension Cable - One () Y-Cable Assembly with Cable
More informationStep 1: The tools you will need: 1x Phillips Screwdriver 1x Vending Machine key
2 3 The tools you will need: 1x Phillips Screwdriver 1x Vending Machine key Step 1: Open the boxes and inventory each of the parts before assembling. Each stand will consist of 1 16 inch Round Base, 1
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationMUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections
insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extention 2-3 Improved Fire Hydrant Inserting Extention
More informationi f c o L INC. COMPLETE MOTORIZED GLIDE OUT ADJUSTMENTS PROCEDURE MANUAL #400011
i f c o L INC. 24076 Reedy Dr. Elkhart, IN 46514 (574)-266-5551 (Office) (574)-206-9296 (Fax) COMPLETE MOTORIZED GLIDE OUT ADJUSTMENTS PROCEDURE MANUAL #400011 The following procedures are used to acquire
More informationPro-Doweling Kit USER S MANUAL #840. Visit us at
Pro-Doweling Kit USER S MANUAL #840 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this manual carefully and thoroughly
More informationUSER MANUAL & PARTS LIST MODEL 40B S/N:
NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST MODEL 40B S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME 04479 www.numberall.com office@numberall.com TEL: 207-876-3541 FAX: 207-876-3566 MODEL
More informationPanosaurus Rex. May Please Visit To view the setup video for the Panosaurus Rex.
Panosaurus Rex May 2009 Please Visit http://gregwired.com/pano/support.htm To view the setup video for the Panosaurus Rex. Note: There currently is no printed setup information available. This booklet
More informationINSTALLATION & ADJUSTMENT INSTRUCTIONS FOR LETHAL WEAPON MODEL 150 & MODEL 200 SIGHTS AND ACCESSORIES
Sight Assembly...................2 Mounting Sight on Bow: LW 1.........................2 LW 2.........................3 LW MAX.....................3 Set-Up and Adjustment: 2-Axis Leveling................4
More informationLumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:
Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.
More informationM1 GARAND CASM. Removing the M1 REAR APERTURE SIGHT. Tools Required A thick [ but not too wide ] flat blade screw driver.
1 Removing the M1 REAR APERTURE SIGHT M1 GARAND CASM Tools Required A thick [ but not too wide ] flat blade screw driver. 1. Turn the elevation knob on the left side of the rear sight clockwise to raise
More informationHigh Rise Sit-Stand Desk Converter
High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC350 Patent No. 9,332,839 PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video
More information4. Z-axis assembly. 4. Z-axis assembly. Written By: Josef Prusa manual.prusa3d.com Page 1 of 18
4. Z-axis assembly Written By: Josef Prusa 2017 manual.prusa3d.com Page 1 of 18 Step 1 Get the necessary tools 13/17mm spanners 3.6mm flathead screwdriver Needle-nose pliers 2.5 and 1.5mm Allen key Step
More informationSIMPLEX STUDIO ELITE MAT CUTTER
INSTRUCTION MANUAL MODEL 700- SIMPLEX STUDIO ELITE MAT CUTTER INSTRUCTIONS AND OPERATION MANUAL 0 inch (50 cm) capacity mat cutting system with bevel & straight cutters, production stops and squaring arm
More informationHOW TO TUNE A QB SERIES CO2 AIRGUN FOR NOOBS.
THE UK CHINESE AIRGUN FORUM PRESENTS... HOW TO TUNE A QB SERIES CO2 AIRGUN FOR NOOBS. DISCLAIMER: THE FOLLOWING GUIDE WILL IMPROVE THE PERFORMANCE AND SMOOTHNESS OF THESE AIRGUNS, IT IS ESSENTIAL THAT
More information.00025" PER CLICK. As you turn the adjustment screw you should be able to feel a click. Each click will change the part diameter.00025".
ULTRA PRECISION DIAMETER ADJUSTMENT.00025" PER CLICK The ultra precision diameter adjustment is extremely accurate, as well as, quick and easy to use. The adjustment mechanism is spring loaded to take
More informationReplacing the build plate clamps
Repair manual Replacing the build plate clamps Instructions The build plate clamps hold the glass plate in place on the heated bed. There are two fixed in place at the back of the heated bed and two at
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationHow to Operate Hurricane Shutters
How to Operate Hurricane Shutters NOTES for PORTFOLIO: I created this manual as a booklet for a family who could not operate their hurricane shutters without paying for service. To develop the manual,
More informationKawasaki Mule Pro Upper Doors #06020 Installation & Operations Manual
Kawasaki Mule Pro Upper Doors #06020 Installation & Operations Manual Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door System is
More informationCHAPTER 8. Through Dovetail Procedures
CHAPTER Through Dovetail Procedures 52 Chapter D4 User Guide THROUGH DOVETAIL PROCEDURES Chapter Foreword In these instructions for using the Leigh Dovetail Jig, we have recommended using certain cutters
More informationSIMPLEX ELITE MAT CUTTER
INSTRUCTION MANUAL MODEL 750-1 / 760-1 SIMPLEX ELITE MAT CUTTER INSTRUCTIONS AND OPERATION MANUAL 40 in (101 cm) mat cutting system with bevel & straight cutters, production stops, 27 in (68 cm) squaring
More informationM*CARBO Winchester Model 70 Trigger Spring Kit Download or Print Instructions Contact: Page 1
Download or Print Instructions Contact: help@mcarbo.com Page 1 Step 1: Clear your Firearm - Remove the magazine, check the chamber, bolt face and magazine well. Step 2: Gather Parts and Tools Needed Step
More informationJUMBO STENCIL CUTTING MACHINE PARTS LIST AND OPERATING MANUAL
JUMBO STENCIL CUTTING MACHINE PARTS LIST AND OPERATING MANUAL Marion, IL USA STK. NO. 5800-152, REV A Warning: This machine contains pinch points which can injure personnel when not used properly. This
More informationSetup & Operating INSTRUCTIONS. for (FOR PIN FITTING AND ROD RECONDITIONING)
I-AG-400A Setup & Operating INSTRUCTIONS for SUNNEN AG-400 PRECISION GAGE (FOR PIN FITTING AND ROD RECONDITIONING) AG-400 Precision Bore Gage Range:.375 to 2.687 in. (9,5-68mm) Graduation of Dial:.0001
More information2. Stand mainframe upright and cut bungee cord tie strap.
2 3 1. Remove the seat rail from the main frame by first removing vertical frame tensioning bolt and the lower seat rail to main frame bolt as shown. Remove the entire seat rail/footplate assembly from
More informationElevation M16 A2-1 click=1 ¼ MOA M4-1 click=2 MOA
1 2 MUZZLE Elevation M16 A2-1 click=1 ¼ MOA M4-1 click=2 MOA UP When zeroing, adjust elevation with the front sight post and make windage adjustments with the rear sight The arrow that is stamped on the
More informationNUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME TEL: FAX:
NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST MODEL 301 S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME 04479 www.numberall.com office@numberall.com TEL: 207-876-3541 FAX: 207-876-3566 MODEL
More informationPACIFIC LASER SYSTEMS. HVL100 Procedures
PACIFIC LASER SYSTEMS HVL100 Procedures A. Setting Up for Level Calibration of Horizontal Lines, Plumb and Down pg. 2 B. Setting Up for Vertical Line Calibration pg. 4 C. Setting Up for Square Calibration
More informationAdjusting Ibanez SR405QM Truss Rod
Adjusting Ibanez SR405QM Truss Rod High tension caused by the strings can cause the wood of the fret board to bow. This bowing can become so extreme it becomes difficult or impossible to play on due to
More informationsig pro TM LASER (SPP) Handling & Safety Instructions
OM-20871-USA v10.28.99 2/2/00 2:35 PM Page 1 SIG Arms AG CH-8212 Neuhausen am Rheinfall Switzerland Phone: (052) 674 65 65 Fax: (052) 674 64 18 SIG Arms Inc. Corporate Park Industrial Drive Exeter, NH
More informationHow to Change the Flint and Wick in a Scripto Vu-Lighter 2011 by Andrew G. Rowe Version 1.01 Table of Contents
How to Change the Flint and Wick in a Scripto Vu-Lighter 2011 by Andrew G. Rowe Version 1.01 Table of Contents Foreword Chapter 1: Page 2 - Flint Replacement Chapter 2: Page 4 Wick Replacement Foreword
More informationInventory MODEL H7937 TAPER ATTACHMENT FOR THE G0600 LATHE INSTRUCTIONS. Inventory (Figure 1) Needed Items
MODEL H7937 TAPER ATTACHMENT FOR THE G0600 LATHE INSTRUCTIONS Inventory The Model H7937 taper attachment was carefully packed when it left our warehouse. If you discover it is damaged after you have signed
More informationOperation Manual Panel Mounting Gas Pressure Regulators
687 Technology Way Napa, CA 94558 Phone: (707) 259-0102 FAX: (707) 259-0117 www.aptech-online.com Table of Contents: A. General information... 1 B. Panel Mount Nut - AP/AZ/AK/SL Model Regulators... 1 C.
More informationMotorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions
Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented
More informationAstro-Physics Inc. 400QMD Lubrication/Maintenance Guide
Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationV-Groover SIMPLEX INSTRUCTION AND OPERATION MANUAL M O DEL 703. For best results use only authentic Logan blades.
www.logangraphic.com SIMPLEX M O DEL 703 INSTRUCTION AND OPERATION MANUAL For best results use only authentic Logan blades CAUTION: BLADES EXTREMELY SHARP Use replacement blades #1258 Logan Graphic Products,
More informationDurst Laborator 138 S
Durst Laborator 138 S -I- G139 Durst Laborator 138 S Durst Laborator G 139 Servicing instructions L 1 3 8 S G 139 - Replacing the counterweight spring The special tool required for this purpose is supplied
More information# in 1 Metal Worker Auxiliary Operating Instructions
340 Snyder Avenue, Berkeley Heights, NJ 07922 www.micromark.com MMTechService@micromark.com Tech Support: 908-464-1094, weekdays, 1pm to 5 pm ET #86556 3 in 1 Metal Worker Auxiliary Operating Instructions
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
More informationPresents the. Partizan MK IV and MkV. Berdan primer conversion systems and tools.
Presents the Partizan MK IV and MkV Berdan primer conversion systems and tools. ***Warning- Russian Reloads takes no responsibility in the reloading of ammunition. Please use safety and caution in your
More informationQB78 CO 2 Pellet Rifle
QB78 CO 2 Pellet Rifle Maintenance Instructions Text and photos by George Fox Lang The Chinese QB78 pellet rifle is one of the nicest and most popular CO 2 rifles ever produced. Here are the long-wanted
More informationZ-Truck Up-and-Down Motion. Y-Truck Side-to-Side Motion. Head. Squaring Plate. Sliding Plate FIGURE 1: THE CARVEWRIGHT MACHINE
Setup and use of CarveWright CO2 Powered Dragster Jig The CO 2 powered Dragster Jig will arrive from the factory fully assembled, calibrated, and squared. In order to get the best results, your CarveWright
More informationStainless Instrument Cluster Cover Installation MK1
Stainless Instrument Cluster Cover Installation MK1 Stainless Instrument Cluster Cover Installation MK1 The installation of an instrument cluster cover in a MK1/NA MX5 requires the removal of the 1. binnacle,
More information(Fig 1) Column to Base 1. Place Column (7) on the Base (13) and align holes in the Column with holes in the Base. 2. Attach using Bolt Washer and Spring Washer hole through the Column and into the Base.
More informationLASER ENHANCED REVOLVER GRIP OWNER S MANUAL RED LASER GREEN LASER
LASER ENHANCED RED LASER GREEN LASER REVOLVER GRIP OWNER S MANUAL LASER ENHANCED GRIP Installation Instructions Caution... 3 Safety Labels... 4 Installation...5-7 Programming...8-10 Batteries (Red Laser)...
More informationCook's Corner Kitchen Assembly Instructions
Assembly Instructions 00 Melissa & Doug, LLC All rights reserved 0 We care about your comments Please call us! -800-84-948 www.melissaanddoug.com PARTS D A E I ( pieces) Q N B F J R ( pieces) S ( pieces)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationThanks for shopping with Improvements! Louvered Pedestal Sink Cabinet Item #512042
Thanks for shopping with Improvements! Louvered Pedestal Sink Cabinet Item #512042 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included). Find a
More informationStep 1: The larger tower box contains the tower machine, a set of Silver 100 Lid Keys, and a set of Black 002 Coin Box Keys
2 3 Step 1: Each tower is shipped as two boxes the large tower box and the smaller stand box. Open each of the boxes and inventory each of the parts before starting assembly to ensure all parts have arrived.
More informationField Inspection Gage. Instruction Manual
Field Inspection Gage Instruction Manual IMPORTANT This Manual details the use of the Denar Field Inspection Gage to calibrate Denar Articulators. For information on the use of the condylar and incisal
More informationAXIOM Rifle Stock. Owner s Manual. Installation Instructions
AXIOM Rifle Stock Owner s Manual Page 1 Installation Instructions ATTENTION: Read and follow all instructions and warnings prior to installation and/or firing a Axiom equipped firearm. Take extra time
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationRepacking the Spindle Bearings on a 1990 Enco RF-30 Mill/Drill, Version 1.1
Repacking the Spindle Bearings on a 1990 Enco RF-30 Mill/Drill, Version 1.1 By R. G. Sparber Protected by Creative Commons. 1 Sorry about the rambling title but it was necessary. I looked at a few videos
More informationOWNERS MANUAL FOR MEC 306XP/408XP WOBBLE
OWNERS MANUAL FOR MEC 306XP/408XP WOBBLE PLEASE READ AND FULLY UNDERSTAND THE INSTRUCTIONS PRIOR TO SETTING OR TUNING THE MACHINE. Page 1 CAUTION: ANY MEC CLAY TARGET MACHINE MUST BE IN THE DISARMED STATE
More information62120LLCP PRECISION LASER SIGHT AND LIGHT INSTRUCTION MANUAL
62120LLCP PRECISION LASER SIGHT AND LIGHT INSTRUCTION MANUAL TABLE OF CONTENTS A.) MOUNTING THE LASER AND LIGHT TO A 1" SCOPE TUBE. B.) REPLACING THE FLASHLIGHT BATTERIES. C.) REPLACING THE LASER BATTERIES.
More informationPhone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels
Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will
More informationYOUR LIFE. YOUR FIRE. Ortal Curved & Islands Fireplaces Installation Manual. Ortal USA - Version: 1.3 November, 2017 SKU: KPMANCIRISLUS17B
YOUR LIFE. YOUR FIRE. Ortal Curved & Islands Fireplaces Installation Manual Ortal USA - Version: 1.3 November, 2017 SKU: KPMANCIRISLUS17B [THIS ISTALLATION MANUAL INCLUDES ASSEMBLY INSTRUCTIONS FOR THESE
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationBunk Pod Front Entry Assembly Instructions
Bunk Pod Front Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod This step by step guide will show how to assemble your pod(s) on site. It
More informationRTI TECHNOLOGIES, INC.
RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally
More information(Shown on Short Riser) Power Button. Elevation. Eyepiece. Adjustment. Objective Lens. Windage. Adjustment. Battery Compartment
RED DOT The Vortex SPARC Red Dot Sight The compact Vortex SPARC red dot lends itself to a variety of firearm platforms including AR-15s, shotguns, and pistols. The modular three-piece base offers four
More informationR-EVO MANUAL. English
R-EVO MANUAL English 1 ENGLISH VERSION Adjusting the holster for your revolver With versatility, refined design, high quality, elegance and resistance - R-EVO, the new GR Holster for revolvers, supplies
More informationUSER'S MANUAL. Compound Crossbow. Raging River Outdoor Products. Tel:
Raging River Outdoor Products Compound Crossbow USER'S MANUAL Raging River Outdoor Products Tel: 1-470-200-0499 Email: sales@ragingriveroutdoors.com www.ragingriveroutdoors.com Please call or email us
More information3400 to 3440 Scarfing Sled Owners Manual Please Read Carefully!
3400 to 3440 Scarfing Sled Owners Manual Please Read Carefully! Parts List: Please identify and verify that you have all of the hardware shown. Please refer to photos in the instructions for the parts
More informationInstalling Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image
UX60-RFK-685 Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image Follow these instructions to install brackets on your SMART Board 685ix
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationInstallation Instructions 8115F 8115SF
TM Installation Instructions 85F 85SF Single Control Centerset Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature
More informationRemoving and Replacing the Y-truck
Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic
More informationHolly Carburetor Flooding and Needle and Seat Fixes
Holly Carburetor Flooding and Needle and Seat Fixes Holley carburetors are sometiines known for flooding over in the event that a float sticks or sinks or debris contaminates the needle & seat, which prevents
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationMM750 Installation Instructions
MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on
More informationCHEMINSTRUMENTS LABORATORY DRAWDOWN COATER LC-100 OPERATING INSTRUCTION
CHEMINSTRUMENTS LABORATORY DRAWDOWN COATER LC-100 OPERATING INSTRUCTION PRODUCT DESCRIPTION...2 UNPACKING...3 ASSEMBLY...4 Key Components...4 Set Up...5 OPERATION...5 MAINTANCE...7 WARRANTY...8 1 PRODUCT
More informationInventory MODEL T10096 TAPER ATTACHMENT FOR G0509 & G0509G LATHE INSTRUCTIONS. Inventory (Figure 1) Needed Items
MODEL T10096 TAPER ATTACHMENT FOR G0509 & G0509G LATHE INSTRUCTIONS Inventory The Model T10096 taper attachment was carefully packed when it left our warehouse. If you discover it is damaged after you
More informationMaintenance & Parts list for:
Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide
More informationMUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections
insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extension 2-3 Improved Fire Hydrant Inserting Extension
More informationModel: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95
Model: SCD430 SCD640 Installation & Operation Guide P/N SCD640-95 Model SCD430 and SCD640 Kurt has two Self-Centering vises, a four-inch jaw width (SCD430) and a six-inch jaw width (SCD640). Jaw opening
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S
More informationInstalling the Exterior Cosmetics
This chapter describes how to install the exterior cosmetics on the Cisco NCS 6000 LCC and includes the following topics: Overview of the Exterior Cosmetics, page Installing the Front Exterior Cosmetics,
More informationFor assembly see instructions in carton
88 5523 943 Kitchen Island IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have
More informationAmerican Morse Equipment
American Morse Equipment Thank you for purchasing an American Morse Porta Paddle-II Kit. We redesigned the original Porta Paddle for ease of assembly & provide all parts finished and ready for assembly,
More informationSTEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT
STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT These instructions apply to newer style TransTrems only (non-threaded ball type or modified threaded ball type). For purposes of discussion, these TransTrems
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More information