INSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. A) Radio Housing I B) ISO Snap-In Brackets I C) Trim Plates (upper & lower) TOOLS REQUIRED:

Transcription

1 INSTLLTION INSTRUCTIONS FOR PRT KIT FETURES DIN Radio Provision with Pocket ISO DIN Radio Provision with Pocket KIT COMPONENTS Dodge Caliber 007 Charger Dakota Durango Magnum Ram Mitsubishi Raider PPLICTIONS ) Radio Housing I ) ISO Snap-In rackets I C) Trim Plates (upper & lower) Chrysler spen 007 PT Cruiser Jeep Commander Compass 007 Grand Cherokee Patriot 007 Upper Trim Plate TOOLS REQUIRED: Phillips Screwdriver Socket Wrench C Lower Trim Plate Small Flat lade Screwdriver or Panel Removal Tool COPYRIGHT 00 METR ELECTRONICS CORPORTION

2 TLE OF CONTENTS Dash Disassembly - Chrysler spen Dodge Dakota Dodge Durango Dodge Charger Dodge Magnum Chrysler Dodge Ram (Without Center Console) Dodge Ram (With Mini Center Console) Dodge Ram (With Full Center Console) Dodge Caliber Jeep Compass Jeep Patriot Jeep Grand Cherokee Jeep Commander Chrysler PT Cruiser Mitsubishi Raider Kit ssembly - DIN Radio Provision with Pocket ISO Radio Provision with Pocket Final ssembly

3 DSH DISSSEMLY 1 CHRYSLER SPEN 007 DODGE DKOT DODGE DURNGO Remove () 7MM screws from the inside of the pocket facing upward. (Figure ) 3 Unclip and remove the entire trim panel surrounding the radio and climate controls. (Figure ) Remove () 7MM screws securing radio. Unplug and remove radio.(figure C) 5 C 1

4 DSH DISSSEMLY DODGE CHRGER DODGE MGNUM Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure ) Remove () 7MM screws securing radio. Unplug and remove radio. (Figure )

5 DSH DISSSEMLY 1 CHRYSLER Unclip and remove entire panel surrounding radio and climate controls, including a/c vents and clock. (Figure ) 3 Remove () 7MM screws securing radio. Unplug and remove radio. (Figure ) 3

6 DSH DISSSEMLY 1 DODGE RM WITHOUT CENTER CONSOLE Open cup holder and remove () Phillips screws facing up on front edge of radio/climate control panel. (Figure ) 3 Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure ) 5 Remove () 7MM screws securing radio. Unplug and remove radio.

7 DSH DISSSEMLY DODGE RM WITH MINI CENTER CONSOLE If vehicle has floor shifter, remove shifter knob. Remove center console inserts, if present. (Figure ) Remove screws securing the rear center console to the floor panel. Lift up on the rear center console to clear the gear shift lever, if present. (Figure ) Remove screws securing the front center console to the floor panel. Unclip and remove the front center console. (Figure C) Remove two phillips head screws at bottom of dash. Unsnap and remove lower panel. Remove () Phillips screws facing up on front edge of radio/climate control panel. (Figure D) Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure E) Remove () 7MM screws securing radio to dash and remove radio. C 10 D E 5

8 1 3 Unsnap and remove console front top cover (closest to the dash). (Figure ) DSH DISSSEMLY DODGE RM WITH FULL CENTER CONSOLE If vehicle has floor shifter, remove shifter knob. Remove two 8 mm screws from under console cover (previously removed). Remove front section of console. (Figure ) 5 Loosen two 8 mm screws at bottom of dash. Unsnap lower panel. 6 Remove () Phillips screws facing up on front edge of radio/climate control panel. (Figure D) D 7 8 Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure E) Remove () 7MM screws securing radio to dash and remove radio. E 9 6

9 DSH DISSSEMLY 1 DODGE CLIER 007 JEEP COMPSS 007 JEEP PTRIOT 007 Unsnap and move shifter trim to the side. (Figure ) 3 (Compass and Patriot only) Unspap and remove top center dash panel above C vents. Unsnap center dash trim panel (do not remove until climate controls are removed). (Figure ) 5 Remove () Phillips screws holding climate control panel to backside of the center dash panel. 6 7 Remove () 7MM screws securing radio. Unplug and remove radio. 7

10 DSH DISSSEMLY JEEP GRND CHEROKEE Unsnap and remove panel from around radio including the vent on each side. (Figure ) 3 Remove () 7MM screws securing radio. Unplug and remove radio. (Figure ) 8

11 DSH DISSSEMLY JEEP COMMNDER Remove the (16) screws securing the radio trim panel. (Figure ) screws screws screws screws 3 Unclip and remove the entire radio trim panel. (Figure ) 5 Remove () 7MM screws securing radio. Unplug and remove radio. 9

12 DSH DISSSEMLY CHRYSLER PT CRUISER Remove () screws from inside air vents on center dash panel. (Figure ) Unsnap center dash panel (do not remove until climate controls are removed). (Figure ) Remove () Phillips screws holding climate control panel to backside of the center dash panel. 5 Remove () 7MM screws securing radio. Unplug and remove radio. 6 10

13 DSH DISSSEMLY MITSUISHI RIDER Unsnap and remove center dash panel. (Figure ) 3 Remove () 7MM screws securing radio. Unplug and remove radio. 11

14 KIT SSEMLY DIN RDIO PROVISION WITH POCKET NOTE: You will need to remove the aftermarket radio s trim ring if equipped. 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) Slide the after-market head unit into the cage and secure. (Figure ) C 3 Using the alignment pins on the trim plates & the corresponding holes in the housing, attach the upper trim plate and the lower trim plate supplied with the kit. Figure C Continue to Final ssembly. 1

15 KIT SSEMLY ISO RDIO PROVISION WITH POCKET NOTE: You will need to remove the aftermarket radio s trim ring if equipped. 1 Mount the ISO rackets to the radio using the screws supplied with the radio. Figure Slide the radio into the opening until it snaps into place. Figure 3 Using the alignment pins on the trim plates & the corresponding holes in the housing, attach the upper trim plate and the lower trim plate supplied with the kit. Figure Continue to Final ssembly. 13

16 C FINL SSEMLY FINL SSEMLY ) Strip wire ends back 1/" ) Twist ends together C) Solder D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Secure the kit into the sub dash using the () 7mm screws that secured the factory radio. 3 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING CODE 1V Ignition / cc... Red 1V att / Memory.. Yellow Ground lack* Power ntenna..... lue mp Turn-On lue / White mp Ground lack / White Illumination Orange Dimmer Orange / White Right Front (+)..... White Left Front (-) White / lack Right Rear (+) Violet Right Rear (-) Violet / lack Left Rear (+) Green Left Rear (-) Green / lack *NOTE: When lack a wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 1

17 NOTES 15

18 NOTES 16

19 NOTES 17

20 INSTRUCTIONS REV. 10/0/06 COPYRIGHT 00 METR ELECTRONICS CORPORTION INST