Assembly instructions for EZ Hang Deluxe
|
|
- Arthur Stevenson
- 6 years ago
- Views:
Transcription
1
2 Assembly instructions for EZ Hang Deluxe EZ Hang Chairs is pleased that you have chosen our EZ Hang Deluxe. While utmost care is taken in the choice of materials and the highest standards are used in manufacturing, caring for your chair at home will extend its life and appearance. Assembly Locate all your EZ Hang Deluxe Chair parts. Including: a) cushion piece (1) b) footrest (1) c) a set of round spreader bars (2) d) a set of bent arms attached to overhead square bar via ropes (1) e) hardware pack wrapped inside cupholder (4) Place wooden bent arms on the ground making sure the arms are face up and that the ropes are not twisted or turned impeding the next step. First insert the rope through the hole on the back of the bent arms and tie a small knot (The brake should be on the back side / if they are on front simply untie the front knot and reverse the clips to the back side).
3 Place the cushion part of the chair with the EZ Hang logo at top right in between the bent arms on the ground. Thread the two round spreader bars through the sleeves underneath the cushion (one sleeve is on top and bottom of the main cushion). Connect the cut away section of the round spreader bars onto the top matching section of the bent wood arms. (Refer to picture to make sure that the bent wood arms are set correctly). Using the hardware provided connect the round spreader bars to the bent wooden arms by placing the hexbolt through the spreader bar and bent wood arms from front to back. Bolt down firmly using the washer and nut. Repeat this procedure in all four corners of the chair. Use the wrench to tighten the bolt until it is flush with the front side of the wood. Installing eyebolt Locate ceiling joist (use stud finder or tap and verify with small nail). Be sure to locate the exact center. Predrill a starter hole using a 3/16 drill bit. Screw in the supplied eyelag until all that is visible is round section. Do not loosen or adjust once in place. Caution (swinging could loosen the eyebolt and compromise the sturdiness). Fine tuning adjustment Your chair can be adjusted back and forward by manipulating the ropes on the overhead square bar. The brakes must be on the back side of the square bar and must sit tight against the square bar once the recline has been set. Washing and care instructions Using a soft brush and warm soapy water, scrub where dirty. Allow to dry hanging or on a flat surface. Disclaimer Please note: Manufacture, Seller, Distributer and all agents or reps thereof cannot assume responsibility for special, indirect, or consequential damages or contingent liability for use of this product in a manner not expressly intended by the manufacturer. End consumer is ultimately responsible for verifying proper installation of the eyelag/ hook assembly according to guidelines explained here within.
4 EZ Hang Loveseat Spreader Bar instructions (Spreader Bar is NOT for hanging the loveseat - see below) Your EZ Hang Love Seat comes with hanging hardware and chain suitable for most standard porch swing frames, such as our own Roman Arch wooden frame (pictured at left). You may, however, choose to hang yours from a tree limb, porch overhang, or other suitable structure. Should you decide to hang your loveseat from a taller structure, you can purchase chain in the proper length and gauge at any hardware store. Make sure you observe our own 500 lb rating when selecting additional chain and/or hardware, and that you hang your loveseat from a structure capable of handling that weight. We have included a 51 wooden spreader bar and 4 mini eyelag bolts to provide a hang point for the footrests in taller support configurations, and/or to support the optional rain cover. When hanging your Love Seat from a hang point taller than 66, make use of the spreader bar as a secondary support point. Install as follows: Insert two of the eyelags into the outermost holes of the spreader bar with the eyes up. Insert the remaining two eyelags into the two centermost holes, eyes down. Secure the eyelags with the washer next to the nut, and tighten all nuts securely. Insert two S-hooks into the outer, up-hanging eyes, and hang the spreader bar 6-12 above the O- rings tied to each side of the supporting ropes on the Love Seat. Tie or hang the footrests to the inner, down-hanging eyes as shown. IMPORTANT: The supplied mini-eyelags and spreader bar are NOT designed to bear the weight of the Love Seat itself, or of any person, and should NOT in any way be inserted into the weight bearing system. Do NOT hang any supporting rope, chain, or the Love Seat off of the mini eyelags or spreader bar.
5 Instructions Assembly Hammock Chair Eyebolt Installation Find ceiling joist (use stud finder or tap and verify with small nail). Be sure to locate the exact center. Drill a hole using a 3/16 drill bit perpendicular to ceiling. Screw in the included eyebolt/hook assembly until all threads are not visible. Do not loosen or adjust once installed. Hole must be directly in the center of the stud for full weight bearing capacity. Spinning or swinging could loosen and compromise the eyebolt strength. Hanging Hammock Chair Hang the Hammock Chair by the O ring onto the pre-installed eyebolt/hook. Washing Instructions Scrub gently with a soft brush and a mixture of water and soap. Using a fabric protector will enhance the look of your chair longer. No machine wash. Disclaimer Culture Shock Trading company INC and all agents thereof cannot assume responsibility for special, indirect, or consequential damages, injury, or contingent liability for use of this product in a manner not intended by manufacturer. End consumer is ultimately responsible for Verifying proper install of eye-bolt according to guidelines here within.
6 ROMAN ARCH INSTRUCTIONS CONTENTS LIST HARDWARE 1. Top Arch Piece 5. 4 ½ Bolt Assembly Set 2. Straight Lower Leg Supports 6. 8 ½ Bolt Assembly Set 3. Arch Support (Slightly Curved) 7. 6 Eyebolt Assembly Set 4. Curved Legs 8. Eyebolts for use with two separate chairs on the arch ESSENTIAL TIPS FOR ASSEMBLY: a. Use 2 people to assembly Roman Arch b. Hand tighten bolts until completely assembled, then tighten all the way. c. Use pictures often for assembly referral d. Straight leg supports go on outside of arch e. Arch support piece has two sides. One side has a sharp angle and one side has short angle. ASSEMBLY STEPS: Connect lower leg support with two curved legs at the bottom using # 5 (4 ½ bolt assembly.) Straight Lower Leg Support Attach one end of Arch Support (# 3) to previously assembled curved legs (#6) using 8 ½ bolt assembly. NOTE: The short angled side of the arch support goes in between the legs.) Slightly Curved Arch Support Repeat lower leg support and arch support assembly for other side of Arch. Page 1
7 Connect 2 previously assembled leg pieces with top arch piece (#1) using 8 ½ bolt assembly (#5.) NOTE: Refer to pictures to assist in Set up. Top Arch Piece Assembled Leg Pieces Connect long angled side of arch support to top arch piece using 6 Eyebolt assembly set (#7.) NOTE: The loveseat hangs from this 6 eyebolt on each side.) Long Angled side of Arch Support Tighten all bolts completely tight. Page 2
8 Assembly instructions for Frame Parts Included: (1) X Section of Frame (2) Lower Section of Frame (3) Top Section of frame (4) 2 additional side support brackets (5) Hardware Pack, Tool, Instructions Assembly Instructions (6) Insert lower section of frame into the center hole of X section. Connect the two sections using the long bolt in the top hole and short bolt in bottom hole. The top long bolt goes all the way through when completely tightened. Tilting the frame forward can assist in correctly aligning bolts. (7) Connect top section to the lower section and align holes and tighten completely with the two allen bolts. (8) If desired attach two side support brackets to the X section of the frame using the hardware included. (9) Hang chair from Hook point at top of upper section.
9 Care It may be necessary to spray frame occasionally with rust preventative spray paint to enhance appearance. Reminder The frame is not intended to swing or twist in. Always exit frame front to back and not sideways. Use caution. Disclaimer Destin Trek Imports and all agents thereof cannot assume responsibility for special, indirect, or consequential damages, injury, or contingent liability for use of this product in a manner not intended by manufacturer. End consumer is ultimately responsible for verifying proper assembly of frame.
Assembly Instructions for model: VMPR1
Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationOffice Partitions WARNING. Assembly Instructions. Customer Service A S S E M B LY HARDWARE H1 H2 H3 H4 H5 H8 H9 H10 H11 H12
Customer Service 1-800-645-2986 Assembly Instructions WARNING In order to prevent structural failure, instability, t i p - o v e r, and/or serious injury, please follow i n s t ructions care f u l l y.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More information2 ADULTS REQUIRED FOR ASSEMBLING
2 ADULTS REQUIRED FOR ASSEMBLING If you have any questions regarding assembly or if you are missing parts, do not return this item to Retailer Store Please call our customer service number and have your
More informationProjector Ceiling Mount
INSTALLATION MANUAL Projector Ceiling Mount PID:3010 PID:5466 20kg (44lbs) RATED CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! ISSUED: FEB. 2013 NOTE: Read the
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More information104 PORCH SWING ASSEMBLY INSTRUCTIONS
104 PORCH SWING ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality porch swing. The product you have purchased requires some assembly. This item has been carefully inspected before packing to ensure
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationTP4463. ASSeMBly INSTruCTIONS FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3
TP63 FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3 Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount ASSeMBly INSTruCTIONS for your safety, please follow these precautions:!
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationINSTALLATION INSTRUCTIONS
CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone:
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationUniversal Projector Ceiling Mount Model: DPM-45
Universal Projector Ceiling Mount Model: DPM-45 Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information represented within this
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationADULT ASSEMBLY REQUIRED
ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if you are missing parts, do not return this item to the Retailer Store Please call our customer service number and have your instructions
More informationSUMMERHOUSE PERGOLA ASSEMBLY INSTRUCTIONS. Toll-free: MODEL NO
SUMMERHOUSE PERGOLA MODEL NO. 088-1759-2 INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm Model: AM300/AM300-B NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations
More informationMERRY GO ROUND ITEM NO: 8030
MERRY GO ROUND ITEM NO: 8030 OWNER S MANUAL CAUTION: This unit is designed to be used safely by up to 4 children between the ages of 3 years to 8 years old with a maximum weight of 00 pounds (45.4 kgs)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS P4263F Universal Low Profi le Flat Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888
More informationsouthpaw enterprises, inc.
southpaw enterprises, inc. Instruction Sheet C-STAND 7100 Store these instructions in a safe place or with the enclosed maintenance checklist Take time to familiarize yourself with the use and maintenance
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationLC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60
More informationET-PKL100S. Installation Instructions. Ceiling Mount Bracket (for Low Ceilings) Model No.
Installation Instructions Ceiling Mount Bracket (for Low Ceilings) Model No. ET-PKL100S Thank you for purchasing this Panasonic Product. JJ To customers The Installation Instructions is intended for use
More informationInstallation Instructions
Installation Instructions 000964 Revision F Installation Instructions for PIRIT Read this manual fully prior to starting installation. Call American eating Customer ervice with any questions. What you
More informationAssembly Instructions for Model: MF110
Assembly Instructions for Model: MF110 Thank you for choosing a Sanus Systems VisionMount wall mount. The MF110 is designed to mount LCD flat panels with VESA (Video Electronics Standards Association)
More informationTilting, Swiveling & Rotating Flat Panel Wall Mount
Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: VXA980TC +5 to -5 +5 to -5 Supports most 0-80 Flat Panel TVs Maximum Weight Capacity: 32 lbs. Supports VESA Sizes up to 600x500 For technical
More informationMSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit for use with Island Display Skybox
INSTALLATION INSTRUCTIONS MSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit for use with Island Display Skybox The MSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit provides a sturdy support for LCD displays
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationK1098 Priceless Salon Styling Chair
K1098 Priceless Salon Styling Chair Keller International, LLC. 1-800-572-8772 1 Part # Part Name Picture Pieces 1 Armrests 1 left and 1 right 2 Backrest 1 3 Seat 1 4 Footrest 1 5 Pump Bail 1 6 G2 Pump
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision D Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Premier Mounts Tilting Wall Mount Model: TWM-085 For use with Panasonic 85 Flat Panel NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700
More informationADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES If you have any questions regarding assembly or if you are missing parts, do not return this item to the Sam s Wholesale
More informationInstallation Instructions. Mesh Grille
Installation Instructions Part Number 81114 I-sheet Rev. A1 Mesh Grille For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain
More informationP4263TP. Installation Guide. Low-Profile Tilting Portrait Mount for Flat-Panels
Low-Profile Tilting Portrait Mount for Flat-Panels 1321 S. State College Blvd., Fullerton, CA 92831 USA Weight Limit Maximum Flat Panel Weight: 175 lbs. Warning Statements THE WALL STRUCTURE MUST BE CAPABLE
More informationHow to Build A Porch Swing
How to Build A Porch Swing SUPPLIES USED Tape measure Drill 2.5" Wood Screws 1.5" Wood Screws 2" Finishing nails Hammer (or nail gun if you're lucky) Sand paper/ Electric sander Exterior paint Safety glasses
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationSmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide
SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame
More informationInstalling The Aliens Extermination Deluxe 50" Cabinet with Sintra Marquee
Installing The Aliens Extermination Deluxe 50" Cabinet with Sintra Marquee Document Part #: 040-0262-01 This document describes how to install The Aliens Extermination Deluxe Cabinet with Sintra Marquee
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS AM2 / AM2-B Articulating Swingout Arm NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone:
More informationUS RACK, Inc Falcon Drive, Madera, CA
US RACK, Inc - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTALLATION AND USE INSTRUCTIONS for Long-John Extension Ladder Rack WARNING: Do NOT attempt to install or use this rack without following
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationINSTRUCTION MANUAL MANUAL DE INSTRUCCIONES
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Model Number/ No. de Modelo: WDB101 CLOTHES DRYER STACKING BRACKET CAUTION: BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Avanti
More informationFace Mount to Through-the-Post Mount
Face Mount to Through-the- Mount Cable Runs through Two Corners When going around two corners, it s necessary to tension the cable from both ends as shown in Deck 4. Use the 672 series The tensioning devices
More informationNo. 412, 414, 416 Operations Manual
No. 412, 414, 416 Operations Manual CARE: Occasional oiling of moving parts with machine oil will ease operation and extend the life of the brake. Occasionally check and tighten the lower beam bracket
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationMonoprice Adjustable Tilt/Swivel Flat Panel Wall Mount Model MLB-109B/RLB-102B (PID# 4926)
Monoprice Adjustable Tilt/Swivel Flat Panel Wall Mount Model MLB-109B/RLB-102B (PID# 4926) VESA Compliant up to 770x480 Max Weight: 125lbs UNPACKING INSTRUCTIONS Carefully open the carton, remove the contents
More informationMedium Flat Panel Dual Swing Arm Wall Mount JWD-V
INSTALLATION Medium Flat Panel Dual Swing Arm Wall Mount The single swing arm wall mount is designed for mounting a medium sized flat panel display. The can swing out from, or fold against, the wall depending
More informationItem # L-DN1856SST-E-SFLS SKU# Loveseat:
Stoneridge Loveseat & Sofa Assembly Instruction Item # L-DN1856SST-E-SFLS SKU# 810330969 Loveseat: Sofa: CAUTION: Chair is for setting purpose only. Standing on or misuse of sofa and loveseat may result
More informationModels CW and AW Installation Instructions
Models CW and AW Installation Instructions Please keep these instructions for future reference. Hiddenbed must be dis-assembled before moving. a product of WALLBEDS! MODELS AW and CW HIDDENBED COMPONENTS
More informationPlanar FWMG-MXL INSTALLATION INSTRUCTIONS
Planar FWMG-MXL INSTALLATION INSTRUCTIONS Fixed Wall Mount for Ultra Large Displays 50-98 weighing less than 300 lbs. Part Number: 955-0217-00 Planar, A Leyard 1195 NW Compton Drive Beaverton, OR 97006
More informationInstruction Sheet For: SCM-2
Instruction Sheet For: SCM-2 For more information, please contact us at: 345 Log Canoe Circle, Stevensville, Maryland 2666 Toll Free: 877.28.269 Phone: 40.643.6390 Fax: 40.643.665 www.videomount.com 27
More informationFull Motion LED, LCD TV Wall Mount
8. Adjustment INSTALLATION MANUAL Full Motion LED, LCD Wall Mount 120 +15-15 +5-5 CAUTION: DO NOT ECEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! Adjust to the desired location
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationThanks for shopping with Improvements! Deluxe 10 Closet Organizer (12 deep) Item #461609
Thanks for shopping with Improvements! Deluxe 10 Closet Organizer (12 deep) Item #461609 To order, call 1-800-642-2112 West Chester, OH 45069 0114 If you have questions regarding this product, call 1-800-642-2112
More informationPFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 100 lb. / 45.35 kg. Included Components Wall Mount (Qty 1) Extension Bracket (Qty 1 Pair) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More informationAssembly Instructions for Model: VMPR1
Assembly Instructions for Model: VMPR1 Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LC/LP
More informationsouthpaw enterprises, inc.
Store these instructions in a safe place or with the enclosed maintenance checklist In-FUN-ity Climbing System Assembly Examples This example sheet is intended to supplement the instruction sheets that
More informationAssembly InstructIons
tp50 FLAT PANEL TV MOUNTING SYSTEM OPTION OPTION 2 OPTION 3 Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount Assembly InstructIons for your safety, please follow these precautions:!
More informationPFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More informationSafety Guidelines and Assembly Instructions
Play Action Air Rider TM Safety Guidelines and Assembly Instructions Maximum Weight Limit: 210 pounds We re Here To Help! Call Toll Free 1-888-752-9782 Customer Service: Monday - Friday, 8:00 A.M. to 5:00
More informationKIT ASSEMBLY INSTRUCTIONS
JUMPING JACK TRAILER KIT KIT ASSEMBLY INSTRUCTIONS A torque wrench (provided in the in-store tool kit) is required to assemble this trailer kit. Torque is a twisting (ft.-lb.).copy force measured in foot-pounds
More informationAssembly Instructions for Model: VMPL3
Assembly Instructions for Model: VMPL3 Thank you for choosing a Sanus Systems VisionMount Wall Mount. The VMPL3 is designed to hold 27-84 Flat Panel LCD or Plasma Displays weighing up to 280 lbs. It will
More informationInstallation instruction: Step 1 Remove the bolts (H) with Allen key (F) to separate wall plate unit (A) into two pieces. Wall plate H TV plate Step 2 Step 3 Step 4 10mm (2/5") E D Concrete wall OR Use
More informationAssembly Instructions for Model: VMDD26
Assembly Instructions for Model: VM26 Thank you for choosing a Sanus Systems Vision Mount wall mount. The VM26 is designed to mount up to 63 lat panel televisions weighing up to 175 lb. to a vertical wall.
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm for 37 to 47 Flat Panels Model: AM80 NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888
More informationMM750 Installation Instructions
MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationInstallation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum
More information2 ADULTS REQUIRED FOR ASSEMBLING
2 ADULTS REQUIRED FOR ASSEMBLING If you have any questions regarding assembly or if you are missing parts, do not return this item to Retailer Store Please call our customer service number and have your
More information19 to 39 TV WALL MOUNT - FULL MOTION
19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationSave time! Read the entire manual before beginning Hoister installation.
7801BSZ: 60 (27 kg) System 7802BSZ: 90 (41 kg) System 7803BSZ: 145 (66 kg) System 7806BSZ: 200 (91 kg)system Suspenz 8725 Roswell Road, Suite O-220, Atlanta, GA USA 30350 Tel: 866-SUSPENZ or 770-518-0045
More informationGearBoss AirPro Locker
Installation and Owner s Instructions GearBoss AirPro Locker Wall Installation Island Installation Contents Important User Information...........................2 General...2 Manufacturer...2 Intended
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Short Throw Projector Arm Model: UNI-STA/UNI-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationDASHLEY COLLECTION GAZEBO
DASHLEY COLLECTION GAZEBO MODEL NO. 088-1760-6 INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future
More informationSOCCER TABLE. Assembly Instructions
Updated: 9/30/2015 SOCCER TABLE Assembly Instructions Table of Contents Parts Identifier... 3 Hardware Identifier. 4 Table Assembly Instructions... 5 Table Assembly Pictures..... 6, 7, 8 2 Page Parts Identifier
More informationCastle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA
Castle Frame Assembly Table AT-8 Diagnostics Manual Castle, Inc. Petaluma, CA 800-282-8338 Solutions Index Adjusting the Tabletop.. 8.01 Adjusting the Fence... 8.02 Aligning the Arm... 8.10 Adjusting Bracket..
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision C Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationMONKEY BARS OVERHEAD RACK INSTALLATION
MONKEY BARS OVERHEAD RACK INSTALLATION Thank you for purchasing the New Monkey Bars Overhead storage rack. The most innovative overhead rack on the market WARNING THE PROPER INSTALLATION OF THIS STORAGE
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationOwner s Manual and Assembly Instruction
Owner s Manual and Assembly Instruction Model #: 22-PS120 Model Name: Verona III Swing Set Manual Date: September, 2007 Important: Keep this owner s manual; do not discard in case you need to contact Pacific
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More information