VDM-2X1-WM & VDM-3X1-WM MONITOR WALL MOUNTS

Transcription

1 Instruction Sheet VDM-2X1-WM & VDM-3X1-WM MONITOR WALL MOUNTS VDM-2X1-WM VDM-3X1-WM THANK YOU Thank you for purchasing the VDM-2X1-WM or VDM-3X1-WM monitor wall mounts. Please read these instructions thoroughly before installing or assembling these products. PRODUCT FEATURES Supports up to 55 monitors VDM-2X1-WM = 300 lb. weight capacity VDM-3X1-WM = 350 lb. weight capacity I Rev -

2 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Heed all warnings. Clean only with dry cloth. Keep these instructions. Follow all instructions. Only use attachments/accessories specified by the manufacturer. DANGER HAZARDOUS VOLTAGE: The lightning flash with the arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING: A warning alerts you to a situation that could result in serious personal injury or death. CAUTION: A caution alerts you to a situation that may result in minor personal injury or damage to the product and/or property. NOTE: A note is used to highlight procedures pertaining to the installation, operation, or maintenance of the product. WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to specifications. WARNING: Failure to provide correct structural strength for the component may result in serious personal injury or damage the equipment. The wood studs to which the component is being attached must be a minimum of a 2x4 and may have a maximum drywall thickness of 5/8 (1.6 cm). WARNING: Exceeding the weight capacity may result in personal injury or equipment damage. The combined weight of all components attached to the mount must not exceed weights listed on page 3. WARNING: Be aware of pinch points and do not place fingers in between moving parts. WARNING: Use this product for its intended use and only use attachments recommended by the manufacturer. WARNING: Do not use a damaged product. Return damaged products to a qualified service center for repair. WARNING: Not intended for outdoor use. INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ Lire ces instructions. Respectez tous les avertissements. Nettoyer uniquement avec un chiffon sec. Conservez ces instructions. Suivez toutes les instructions. N'utilisez que des accessoires spécifiés par le fabricant. DANGER TENSION DANGEREUSE: Le symbole de la pointe de flèche, dans un triangle équilatéral, est destiné à alerter l'utilisateur sur la présence de tension dangereuse non isolée dans l'enceinte du produit qui peut être d'une ampleur suffisante pour constituer un risque d'électrocution. AVERTISSEMENT: Un avertissement vous avertit d'une situation pouvant entraîner des blessures graves ou la mort. ATTENTION: Une attention vous avertit d'une situation pouvant entraîner des blessures mineures ou des dommages au produit et/ou à la propriété. REMARQUE: Une remarque est utilisée pour mettre en évidence les procédures relatives à l'installation, au fonctionnement ou à l'entretien du produit. AVERTISSEMENT: Refus de lire, comprendre et suivre la renseignements suivants peut traduire par de graves blessures, des dommages à l'équipement ou invalider la garantie. Il est la responsabilité de l'installateur / utilisateur de s'assurer que ce produit est chargé conformément aux spécifications. AVERTISSEMENT: Le défaut de fournir une résistance structurelle correcte pour le composant peut entraîner des blessures graves ou endommager l'équipement. Les poutrelles de bois dans laquelle le composant est connecté doit être au minimum d'un 2x4 et peuvent avoir une épaisseur de cloison sèche maximale de (1.6 cm (5/8"). AVERTISSEMENT: Dépasser la capacité de poids peut entraîner des blessures ou des dommages matériels. Le poids combiné de tous les composants reliés au support de montage ne doit pas dépasser les grammages indiqués à la page 3. AVERTISSEMENT: Soyez conscient des points de pincement et de ne pas placer les doigts entre les pièces mobiles. AVERTISSEMENT: Utilisez ce produit pour son utilisation prévue et utiliser uniquement les accessoires recommandés par le fabricant. AVERTISSEMENT: Ne pas utiliser un produit endommagé. Retour produits endommagés à un centre de service qualifié pour la réparation. AVERTISSEMENT: Non destiné à une utilisation en extérieur. Page 2

3 WEIGHT RATINGS Model Weight Rating VDM-2X1-WM 300 lbs. (136.0 kg) Maximum Total Rated Load VDM-3X1-WM 350 lbs. ( kg) Maximum Total Rated Load CAUTION: Weight must be distributed evenly and maximum capacity of pair of Display Mounts must not exceed 125 lbs (56.7 kg). ATTENTION: Le poids doit être réparti uniformément et capacité maximale de paire de supports d'affichage ne doit pas dépasser 56.7 kg (125 lbs). SUPPLIED COMPONENTS AND HARDWARE Tilt Bracket B Wall Mount A Model VDM-2X1-WM VDM-3X1-WM (2x) End Cap E Qty. 2 3 Model VDM-2X1-WM VDM-3X1-WM (4x) Flat Head Screw F Button Head Socket Screw L Model Qty. VDM-2X1-WM 6 VDM-3X1-WM 9 Display Mount D Extrusion C Model VDM-2X1-WM VDM-3X1-WM Qty. 2 3 (6x) Hex Head Screw G (6x) Wall Anchor H Cable Clamp T Model VDM-2X1-WM VDM-3X1-WM 5/32 Hex Key U Qty. 4 6 Page 3 (6x) Flat Washer J Qty. 4 6 Long Pan Head Screw K Model Qty. VDM-2X1-WM 4 VDM-3X1-WM 6 (4x) Short Pan Head Screw V (4x) Square Nut W

4 SUPPLIED COMPONENTS (CONTINUED) Below display mount hardware supplied in kits. Model VDM-2X1-WM VDM-3X1-WM Kit Qty. 2 3 Display Mount Screws M4 x 12 M4 x 20 (M-B) (M-A) M5 x 12 (M-C) Combo Washer N M5 x 30 (M-D) M6 x 12 (M-E) M6 x 20 (M-F) (8) Small Spacer P M6 x 30 (M-G) Large Spacer R M8 x 16 (M-H) M8 x 20 (M-J) M8 x 40 (M-K) 5MM Hex Key S REQUIRED TOOLS #2 Phillips Screwdriver Drill Protective Eyewear Level 7/32 Wood Bit 3/8 Cement Bit 1/2 Hex Socket Hammer 5MM Hex Wrench (Supplied) 5/32 Hex Wrench (Supplied) WARNING: Use tools with caution and follow all necessary safety protocols. AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité nécessaires. Page 4

5 16 OR 24 CENTER WOOD STUD INSTALLATION (VDM-2X1-WM) 1. Determine wall center location for mount and find center of stud closest to desired position on the wall and draw a 8 line. Locate the center of the second stud to the left or right of desired location 48 apart and draw a 8 line down the center of the second stud. (FIGURE A) 2. Using a straight edge and a level, place a center mark on both which will be for the top mounting holes on the wall mount. (FIGURE B) Centers FIGURE A Centers FIGURE B Page 5

6 16 OR 24 CENTER WOOD STUD INSTALLATION (VDM-2X1-WM) (CONTINUED) 3. Using the wall mount (A), align top hole and mark the center of the mounting slot on the bottom of each of the two wall mount locations. (FIGURE C) FIGURE C 4. Remove wall mount and using a 7/32 drill bit, drill a 2.5 deep pilot hole in each of the 4 marked center points. (FIGURE D) FIGURE D Page 6

7 16 OR 24 CENTER WOOD STUD INSTALLATION (VDM-2X1-WM) (CONTINUED) 5. Install (2x) wall mount (A) using (2x) hex head screw (G) and (2x) flat washer (J) for each wall mount. (FIGURE E) Keyhole must face up. A J G FIGURE E BLOCK OR CEMENT WALL INSTALLATION (VDM-2X1-WM) 1. Determine the location for mount and draw a 8 vertical line. Locate the center of the second mount position 48 to the left or right of the first line and draw a 8 vertical line down the wall. (FIGURE F) 2. Using a straight edge and a level, place a center mark on both which will be for the top mounting holes on each wall mount. (FIGURE F) 48 FIGURE F Page 7

8 BLOCK OR CEMENT WALL INSTALLATION (VDM-2X1-WM) (CONTINUED) 3. Using the wall mount (A), align top hole and mark the center of the mounting slot on the bottom of each of the two wall mount locations. (FIGURE G) FIGURE G 4. Remove wall mount and using a 3/8 drill bit, drill a 2.5 deep pilot hole in each of the 4 marked center points. (FIGURE H) FIGURE H Page 8

9 BLOCK OR CEMENT WALL INSTALLATION (VDM-2X1-WM) (CONTINUED) 5. Press a wall anchor (H) into each of the 4 drilled holes. (FIGURE J) NOTE: Wall anchors may require a hammer to install. H FIGURE J 6. Install (2x) wall mount (A) using (2x) hex head screw (G) and (2x) flat washer (J) for each wall mount. (FIGURE K) Keyhole must face up. A G FIGURE K Page 9 J

10 16 OR 24 CENTER WOOD STUD INSTALLATION (VDM-3X1-WM) 1. Determine wall center location for mount and find center of stud closest to desired position on the wall and draw a 8 line. Locate the center of the second and third studs to the left or right of desired location 48 apart, total 96 and draw a 8 line down the center of the studs. (FIGURE L) 2. Using a straight edge and a level, place a center mark on each of the two studs which will be for the top mounting holes on the wall mount. (FIGURE L) Centers Centers FIGURE L Page 10

11 16 OR 24 CENTER WOOD STUD INSTALLATION (VDM-3X1-WM) (CONTINUED) 3. Using the wall mount (A), align top hole and mark the center of the mounting slot on the bottom of each of the three wall mount locations. (FIGURE M) FIGURE M 4. Remove wall mount and using a 7/32 drill bit, drill a 2.5 deep pilot hole in each of the 6 marked center points. (FIGURE N) FIGURE N Page 11

12 16 OR 24 CENTER WOOD STUD INSTALLATION (VDM-3X1-WM) (CONTINUED) 5. Install (2x) wall mount (A) using (2x) hex head screw (G) and (2x) flat washer (J) for each wall mount. (FIGURE P) Keyhole must face up. A J G FIGURE P BLOCK OR CEMENT WALL INSTALLATION (VDM-3X1-WM) 1. Determine wall center location for mount and draw a 8 vertical line. Locate the center of the second and third mount locations to the left or right of desired location 48 apart, total 96 and draw a 8 vertical line down the each position. (FIGURE R) 2. Using a straight edge and a level, place a center mark on each of the two positions which will be for the top mounting holes on the wall mounts. (FIGURE R) FIGURE R Page 12

13 BLOCK OR CEMENT WALL INSTALLATION (VDM-3X1-WM) (CONTINUED) 3. Using the wall mount (A), align top hole and mark the center of the mounting slot on the bottom of each wall mount location. (FIGURE S) FIGURE S 4. Remove wall mount and using a 3/8 drill bit, drill a 2.5 deep pilot hole in each of the 6 marked center points. (FIGURE T) FIGURE T Page 13

14 BLOCK OR CEMENT WALL INSTALLATION (VDM-3X1-WM) (CONTINUED) 5. Press a wall anchor (H) into each of the 6 drilled holes. (FIGURE U) NOTE: Wall anchors may require a hammer to install. H FIGURE U 6. Install (2x) wall mount (A) using (2x) hex head screw (G) and (2x) flat washer (J) for each wall mount. (FIGURE V) Keyhole must face up. A J G FIGURE V Page 14

15 EXTRUSION INSTALLATION 1. Slide extrusion brackets (B) onto extrusion (C) oriented as shown. (FIGURE W) Model Extrusion Bracket (B) Qty. VDM-2X1-WM 2 VDM-3X1-WM 3 Top C B FIGURE W 2. Hook extrusion assembly onto each wall bracket (A) as shown. (FIGURE X) VDM-2X1-WM Pre-mounted Wall Brackets A VDM-3X1-WM Pre-mounted Wall Brackets FIGURE X Page 15

16 TILT ADJUSTMENT 1. Tilt bracket (B) is designed with 20 full range adjustment or preset holes in 5 increments. If angle is already known set all tilt brackets to the preset angle by installing (2x) short pan head srews (K) into preset hole on each side of tilt bracket. (FIGURE Y) 2. Insert and tighten (2x) button head socket screws (L) into adjustment slots on both sides of bracket using hex key (U). (FIGURE Y) 3. Repeat steps 1 and 2 for each tilt bracket. B NOTE: Extrusion removed for clarity. K L U Preset Tilt Holes NOTE: If angle is not known, assemble tilt bracket so extrusion is vertical. Once installation is complete, tilt angle can then be set. FIGURE Y Page 16

17 FLUSH DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack. (FIGURE Z) 2. Align display mount bracket (D) with mounting holes on the back of display. Using (4x) display mount screws (M-A - M-K) and (4x) combo washers (N) to secure the display mount brackets to your display. (FIGURE Z) TV TV TV TV D M-A - M-K N FIGURE Z Page 17

18 RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack. (FIGURE AA) 2. Align display mount bracket (D) with mounting holes on the back of display. Using (4x) display mount screws (M-A - M-K), (4x) combo washers (N) and (4x) spacers (P - R) to secure the display mount brackets to your display. (FIGURE AA) TV TV TV TV D P-R M-A - M-K N FIGURE AA Page 18

19 HANGING DISPLAY 1. Tilt display and hook display bracket onto flange of tilt bracket (B). (FIGURE AB) 2.Push along the bottom of display until the mount clicks into place. (FIGURE AB) 3. To remove display from the extrusion, pull both release cord rings down while pulling bottom of display away from wall and lift display off flange of extrusion. (FIGURE AB) NOTE: When installing monitors on VDM-3X1-WM, start with the center display first before installing monitors on ends of extrusion. B Release Cord FIGURE AB Page 19

20 Micro Adjustments 1. If the display is uptilted, rotate the adjustment screws as shown in figure below using hex wrench (S). (FIGURE AC) S S FIGURE AC 2. Rotate the adjustment screws as shown below to make adjustments to align displays using hex wrench (S). (FIGURE AD) S S S FIGURE AD Page 20

21 FINAL ASSEMBLY 1. With extrusion evenly spaced between brackets, install button head socket screw (L) into back of each tilt bracket (B) (either left or right side of bracket) to secure extrusion in place using hex key (U). (FIGURE AE) Model Screw (K) Qty. VDM-2X1-WM 2 3 VDM-3X1-WM B U L FIGURE AE 2. Install safety stops by sliding (2x) square nut (W) into front slots in extrusion as shown and install (2x) short pan head screw (V). Tighten both screws flush with end of extrusion. Repeat both ends. (FIGURE AF) 3. Install end cap (E) with (2x) flat head screw (F), both ends. (FIGURE AF) NOTE: If assembly needs to be tilted, follow Tilt Adjustment procedure on page 16. E F W V Square nuts flush with end of extrusion FIGURE AF Page 21

22 Cable Management 1. Insert the cable clamps (T) horizontally into the extrusion slots, then turn the cable clamps to the vertical to secure in place. (FIGURE AG) T FIGURE AG WARRANTY For warranty information, refer to Corporate Headquarters Corporate Voice: Fax: / International Voice: Fax: info@middleatlantic.com Middle Atlantic Canada Voice: Fax: ca.middleatlantic.com - customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO Registered Company. Page 22