DX-DRTVM114. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations

Size: px

Start display at page:

Download "DX-DRTVM114. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations"

Buddy Miller
5 years ago
Views:

1 ASSEMBLY GUIDE DX-DRTVM11 Low-Profile TV Wall Mount F either wood-stud concrete wall installations Safety infmation and specifications...2 Tools needed Package contents Installation instructions Befe using your new product, please read these instructions to prevent any damage.

2 2 Safety infmation and specifications IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS CAUTION: Do not use this product f any purpose not explicitly specified by Dynex. Maximum TV weight: 120 lbs. (5. kg) Screen size: 37 in. to 70 in. diagonal Overall dimensions (H W ): in. ( cm) Wall-mount weight: 7.5 lbs. (3. kg) We re here f you F customer service, call: (U.S. and Canada) (Mexico) Improper installation may cause property damage personal injury. If you do not understand these directions, have doubts about the safety of the installation, contact Customer Service call a qualified contract. Dynex is not responsible f damage injury caused by increct installation use. The weight of your TV must not exceed 120 lbs. (5. kg). The wall must be capable of suppting five times the weight of your TV and wall mount combined. This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children! 5 Tilt range Maximum VESA pattern Max 800mm (31.9 in.) Max 00mm (15.7 in.)

3 Tools Needed Outils nécessaires Herramientas requeridas Top / Dessus / Vista superi DX-DRTVM11 Wall Plate Template Gabarit de la plaque murale Plantilla de la placa de pared Top / Dessus / Vista superi Note: F wood frame installations, use Remarque : Pour des installations sur des structures en bois, utiliser d'abd un localisateur de montants pour détecter un montant en bois. Nota: para las instalaciones en marcos de madera, use primero un localizad de viga para ubicar las vigas de pared. Imptant: Make sure that the lag bolts are inserted into a wood stud. The distance between two studs is typically 16". V DX-DRTVM11 3 Tools needed You will need the following tools to assemble your new TV wall mount: ardware Level Edge-to-edge stud finder Pencil Drill Phillips driver Socket wrench with 1/2" (13 mm) socket adjustable wrench 7/32" (5.5 mm) wood drill bit f wood stud wall OR 3/8" (10 mm) masonry drill bit (concrete only) Measuring tape Tape Hammer Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount: A Wall Plate (1) C Right TV Bracket (1) B Left TV Bracket (1) D Wall plate template (1) A B C D

4 DX-DRTVM11_ _MAN_V1_ENG.fm Page Monday, July 22, :26 AM TV Hardware Bag Label Hardware M 12 mm E M 30 mm F Label N Hardware Qty. M6 35 mm M8 16 mm O P M6/M8 washer H I 8 M/M5 washer G Qty. M8 0 mm Q M/M5 spacers M8 60 mm M5 12 mm J M5 30 mm K M6 12 mm L 20 S Lag bolt washer T U Concrete anch /16" 2 3/" lag bolt 1 10 M6/M8 spacers M6 20 mm M R 70 in mm

5 DX-DRTVM11 5 Installation instructions STEP 1- Determine whether your TV has a flat back an irregular obstructed back 1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. 2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV f instructions. 3 Temparily lay the TV brackets (B and C) on the back of your TV. Align the holes in the TV brackets with the mounting holes on your TV. 5 Identify which type of back your TV may have: Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers when assembling the wall mount. Obstructed back: The brackets block one me of the jacks on the back of your TV. You will need spacers when assembling the wall mount. Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You will need spacers when assembling the wall mount. 6 Remove the TV brackets.

6 6 STEP 2 - Select s, washers, and spacers 1 Select the hardware f your TV (s, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are s that came with the TV, they are almost always in the holes on the back of the TV.) If you don't know the crect length of the mounting s your TV requires, test various sizes by hand threading the s. Select one of the following types of s: Flat back M 12 mm s (E) M5 12 mm s (J) M6 12 mm s (L) M6 20 mm s (M) M8 16 mm s (O) M 30 mm s (F) M5 30 mm s (K) M6 35 mm s (N) M8 0 mm s (P) M8 60mm s (Q) Obstructed back Select from the following washers: M/M5 washer (G) M6/M8 washer(h) F an irregular obstructed TV back, use the following spacers: M/M5 spacer (I) M6 /M8 spacer (R) Screw fits crectly CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Use the shtest and spacer combination to accommodate your TV. Using hardware that is too long may damage your TV. However, using a that is too sht may cause your TV to fall from the mount. Screw is too long Screw is too sht Note: If you plan to use a 5 tilt with a larger TV (2 +), we suggest using spacers with the mounting brackets so that the bottom of the TV does not touch the wall. 2 Remove the s. 3 F a flat back TV, go to STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back on page 7. -OR- F an irregular obstructed back, go to STEP 3 - Option 2: Attaching the mounting hardware to TVs with irregular obstructed backs on page 8.

7 DX-DRTVM11 7 STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back Note: If you plan to use a 5 tilt with a larger TV (2 +), we suggest using spacers with the mounting brackets so that the bottom of the TV does not touch the wall. 1 Align the left and right TV brackets (B and C) with the holes on the back of the TV. Make sure that the brackets are level. 2 Install washers (G H), and s (E, J, L, M, O) into the holes in the back of the TV. 3 Tighten the s until they are snug against the TV brackets. Do not over tighten. H E J L M O You ll need Screws Washers E () L () J () G () H () M () O () Level Phillips driver B and C TV brackets

8 8 STEP 3 - Option 2: Attaching the mounting hardware to TVs with irregular obstructed backs Note: If you plan to use a 5 tilt with a larger TV (2 +), we suggest using spacers with the mounting brackets so that the bottom of the TV does not touch the wall. 1 Align the left and right TV brackets (B and C) with the holes on the back of the TV. Make sure that the brackets are level. 2 Place spacers (I R) behind the TV brackets. If you are using M/M5 washers (G), place them between the spacers and TV brackets and over the holes in the TV brackets. If you are using M6/M8 washers (H), place them over the holes in the TV brackets. Insert s (F, K, N, P, Q) through the washers, TV brackets, and spacers. 3 Tighten the s until they are snug against the TV brackets. Do not over tighten. I R K N P Q You ll need Screws F () K () N () P () Q () Level Phillips driver Washers G (8) H () Spacers I () R () B and C TV brackets

9 DX-DRTVM11 9 STEP - Attaching the tilt brackets Note: If you plan to use a 5 tilt with a larger TV (2 +), we suggest using spacers with the mounting brackets so that the bottom of the TV does not touch the wall. 1 Remove the s holding the tilt brackets to the TV brackets (B and C). 2 Align the tilt bracket so that the 5 shows on the bracket f a 5 tilt. -OR- Align the tilt bracket so that the 0 shows on the bracket f a 0 tilt. 3 Do the same to the other TV bracket. Replace the s and tighten firmly. Option 1: -5 Tilt 1 B 2 & C B & C Option 2: No Tilt (0 ) 1 B 2 & C B & C You ll need Phillips driver

10 10 STEP 5 - Determine wall-mount location Notes: F me detailed infmation on determining where to drill your holes, visit our online height-finder at: Your TV should be high enough so your eyes are level with the middle of the screen. Nmally, 0 to 60 inches from the ground. The center of your TV will match the center of the wall plate (A). Befe you drill holes in the wall: 1 Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is measurement a. 2 Measure the distance from the flo to where you want the bottom of the TV to be placed on the wall. Keep in mind that the bottom of the TV should be placed above any furniture (such as entertainment centers TV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray player cable box). This measurement is b. 3 Add a + b. The total measurement is the height where you want the center of the wall plate to be on the wall. Use a pencil to mark this spot on the wall. Aa bb You ll need Measuring tape Pencil

11 DX-DRTVM11_ _MAN_V1_ENG.fm Page 11 Monday, July 22, :26 AM 11 DX-DRTVM11 STEP 6 - Option 1: Installing on a wood stud wall Note: Any drywall covering the wall must not exceed 5/8" (16 mm). 1 Locate the stud. Verify the center of the stud* with an edge-to-edge stud finder. 2 Align the wall plate template (D) at the height you determined in the previous step, make sure that it is level, then tape it to the wall. Use a pencil to mark the lag bolt hole locations () on the stud centers. 3 Drill pilot holes to a depth of 3 in. (75 mm) using a 7/32 in. (5.5 mm) diameter drill bit. Remove the wall plate template. Align the wall plate (A) with the pilot holes, insert the lag bolts (T) through the lag bolt washers (S), then through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall plate. CAUTION: Avoid potential injuries property damage! DO NOT over-tighten the lag bolts (T). - Minimum wood stud size: common 51 x 102 mm (2 x in.) nominal 38 x 89 mm (11/2 x 31/2 in.). - Minimum spacing between hizontal fasteners cannot be less than16 in. 3 in. (75 mm) You ll need Pencil Wall plate (A) Top / Dessus / Vista superi Tools Needed Outils nécessaires Herramientas requeridas DX-DRTVM11 Wall Plate Template Gabarit de la plaque murale Plantilla de la placa de pared Drill Edge-to edge stud finder 7/32" wood drill 1/2" socket wrench bit Top / Dessus / Vista superi Note: F wood frame installations, use Remarque : Pour des installations sur des structures en bois, utiliser d'abd un localisateur de montants pour détecter un montant en bois. Nota: para las instalaciones en marcos de madera, use primero un localizad de viga para ubicar las vigas de pared. Imptant: Make sure that the lag bolts are inserted into a wood stud. The distance between two studs is typically 16". V Wall plate template (D) S () T () Level Tape

12 DX-DRTVM11_ _MAN_V1_ENG.fm Page 12 Monday, July 22, :26 AM 12 STEP 6 - Option 2: Installing on a solid concrete concrete block wall* CAUTION: To prevent property damage personal injury, never drill into mtar between blocks. Mount wall plate directly onto the concrete surface. Align the wall plate template (D) at the height you determined in the previous step, make sure that it is level, then tape it to the wall. Use a pencil to mark the lag bolt hole locations (). Drill pilot holes to a depth of 3 in. (75 mm) using a 3/8 in. (10 mm) diameter masonry drill bit. Remove the template. Insert the concrete wall anchs (U) into the pilot holes and use a hammer to make sure the anchs are flush with the concrete surface. Align the wall plate (A) with the anchs, insert the lag bolts (T) through the lag bolt washers (S), then through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall plate. CAUTION: Avoid potential injuries property damage! DO NOT over-tighten the lag bolts (T). * Minimum solid concrete thickness: 8 in. (203mm). * Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 06 mm). The minimum distance between the top two fasteners cannot be less than 16 in. 3 in. (75 mm) You ll need Top / Dessus / Vista superi Tools Needed Outils nécessaires Herramientas requeridas DX-DRTVM11 Wall Plate Template Gabarit de la plaque murale Plantilla de la placa de pared 3/8" masonry drill bit Pencil Wall plate (A) Edge-to edge stud finder Top / Dessus / Vista superi Note: F wood frame installations, use Remarque : Pour des installations sur des structures en bois, utiliser d'abd un localisateur de montants pour détecter un montant en bois. Nota: para las instalaciones en marcos de madera, use primero un localizad de viga para ubicar las vigas de pared. Drill 1/2" socket wrench Imptant: Make sure that the lag bolts are inserted into a wood stud. The distance between two studs is typically 16". V Wall plate template (D) S () U () T () Level Tape

13 DX-DRTVM11 13 STEP 7 - Mounting the TV to the wall plate 1 Place the TV brackets (B and C) into the slotted flanges of the wall plate (A). 2 Push the bottom of the TV toward the wall until the latch mechanism clicks into place. HEAVY! You will need assistance with this step. B and C A

14 1 Removing the TV from the wall plate 1 Grasp the TV by the bottom edge, then pull down on the locking cds and pull the bottom of the TV out from the wall. 2 Release the locking cds and lift the top of the TV from the wall bracket. HEAVY! You will need assistance with this step. Pull down to unlatch.

15 (U.S. and Canada) (Mexico) Distributed by Best Buy Purchasing, LLC 7601 Penn Ave. South, Richfield, MN 5523 U.S.A BBY Solutions, Inc. All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners V1 ENGLISH

DX-DRTVM102. Medium Low Profile Wall Mount with Optional 5 Tilt ASSEMBLY GUIDE

DX-DRTVM102. Medium Low Profile Wall Mount with Optional 5 Tilt ASSEMBLY GUIDE ASSEMBLY GUIDE DX-DRTVM102 Medium Low Profile Wall Mount with Optional 5 Tilt Safety infmation and specifications... 2 TVs the wall mount fits... 3 Tools needed... Parts... Hardware... 5 Assembly instructions...