Assembly instructions
|
|
- Cassandra Nash
- 5 years ago
- Views:
Transcription
1 Nerdy Gurdy Assembly instructions This manual describes how to assemble a Nerdy Gurdy kit. Go to for more info about these instruments. Jaap Brand The Netherlands January 2018 General directions: The parts are glued together with regular wood glue (not included in the kit). Don t glue the bridge or any part that s adjustable. Make sure that all surfaces that touch are fully glued together. This prevents undesirable vibration when you re playing. When removing parts from the plate that are still attached, it s best to cut the attached points with a sharp knife, to avoid splintering. Before gluing, it is wise to assemble the parts without glue, so that you re sure how they fit together. You can assemble most of the instrument without glue, to get an idea of how the parts go together. It s best to read through the whole sequence, before starting. If you do something wrong, it is possible to release wood glue by heating it (e.g. with a pressing iron)
2 Parts Included wood sheet 3mm 4x sheet 6 mm 2x Loose parts pegs 5x threaded rod M8 6cm 1x threaded rod M8 24cm 1x nut 8mm 11x nut M3 4x shaft bush-ring 1x bolt M2,5 x 10 48x bolt M3 x 10 4x bearing 8x22 3x screw 2,5 x 13 4x screws back plate/strap pins 3.5 x 17 6x spacer ring 8,4 mm 5x felt 1x ground ring terminal 2x strings chantarelle (viola) 2x trompet 1x bourdon (cello) 1x printed parts Knob (A) 1x tangent high (B) 28x tangent low (C) 20x shaft nut (D) 1x bearing ring (E) 2x strap pin (F) 2x Front bearing assy (G) 1x backplate glueing jig (H) 1x Finished parts wheel 1x
3 Not included in kit You will need the following materials to build your Nerdy Gurdy (not included in the kit): Standard wood glue (retractable) knife A number of gluing clamps Varnish (optional, but recommended) Sand paper Some tools (screw drivers, 13 mm spanner, etc.) Some basic woodworking skill and patience :)
4 1) Glue the borders to the top and bottom of the Nerdy Gurdy Notes: Make sure that you glue the border to the correct side of the top plate: it s not symmetric (red circle) The two borders are symmetric and identical Make sure that the parts are nicely centered. You can use mating parts to check alignment (picture below) You can use some books to press the parts together
5 2) Assemble the head and front bearing support head Front bearing support
6 3) Mount the head between the top, pillar and rear between the top plate and bottom plate. Notes: Make sure that the opening at the rear side is at the top of the Gurdy (red circle).
7 Front bearing The shaft is screwed into a bush at the front bearing, to avoid it from rattling. It s most easy to assemble this before you attach the sides to the instrument. There is a hole in the bush to prevent it from rotating, when you re assembling the shaft. Attach the bearing holder with 2 x [screw, 2.5 x 13]
8 3) Mount the sides, starting from the head Notes: You can glue the parts in steps, if you don t have enough clamps (like me). I use the machine heads to clamp the head plates together. Complete the head, assemble the bridge Notes: You don t need to glue the bridge: it may be nice to be able to replace it. A spare part is included. Some spacers are included (red circle)
9 Assemble the tailpiece Make sure these parts are on the correct side, as shown Notes: Make sure that you insert the nuts, before you glue everything together. I use the top plate as a mold, to ensure the spacing of the bridge parts is correct.
10 Place the bolts, wedge parts and bridge segments There are two types of tuning peg. For the other positions both will fit ok. For the tail piece you need to use the correct version.
11 Glue the rear cover pieces together A tool is included to align the pieces for gluing Assemble the key box
12 Glue the lid pieces together Notes: A blank plate is included in the kit, if you don t want to have the lettering on top. Glue the buzzing bridge support together
13 Apply lacquer You may want to lacquer or paint your parts at this point in the assembly. Glue an extra layer on top of the short keys Notes: The numbers are on the top of the keys. That s the side on which you need to stick the extra layer.
14 Glue the key box to the body, and assemble keys and tangents Assemble the bourdon support and buzzing bridge support Don t glue these parts, just place them!
15 Assemble the shaft Notes: The printed ring is screwed to the back plate, to secure the bearing (2 x [screw, 2.5 x 13]). You may need to add some glue to lock the thread of the nut that secures the knob. Else it may come loose while turning. Alternatively you can use a locking nut (included in newest kits).
16 Assemble the wheel The wheel slides into the slot on top, and you screw the shaft into the wheel. In the end, the shaft needs to be screwed into the bush with the front bearing. Insert a pin into the bush, to prevent it from rotating: You may need to tweak the locations of the nuts on the shaft a bit, to get the shaft properly aligned and straight. The shaft may not be perfectly straight, so you will need to true the wheel after you assemble it. Rotate it by hand and apply a scraping iron or horizontal chisel, until it is perfectly round. Afterwards, finish with fine sanding paper.
17 Mount the strap pins Mount the strings
18 Notes: You need to tie a short string from the machine head at the rear, to the string. With this knob you can adjust the trumpet effect. You may need to tweak the location of the string a bit, to get a good buzzing effect.
19 Final notes I ve designed this instrument with the purpose of making a Hurdy Gurdy with an acceptable sound, for a very good price. I hope that it enables people to start playing the instrument who would not have had the means otherwise, or are hesitant to invest thousands of dollars straight away. The design is unconventional: it was designed from scratch with the above purpose in mind. Therefore the construction method is in many ways different from traditional instruments. It does however sound pretty good, and it is very playable. And because of the material and the method of construction, it is very stable New players will still need to learn how to properly apply rosin to the wheel, and cotton to the strings. But there are many tutorials online, if you don t have experienced players who can teach you. Enschede, January 2018 Ps. This manual and the Nerdy Gurdy itself are an ongoing project. Please let me know how they can be further improved.
Assembly instructions
Nerdy Gurdy Assembly instructions This manual describes how to assemble a Nerdy Gurdy. Go to http://www.nerdygurdy.nl for more info about these instruments. Jaap Brand The Netherlands January 2018 General
More informationParts & Tools. O'Cello printing and assembly instructions. o-cello.com
The O'Cello is a 3D-printable cello developed by Conor O'Kane, which is free to download and print for personal use. This document will show you how to print and assemble your own O'Cello. For the latest
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationTool 3-1 A2 Bushing 6 Check if the bushing supports (angle iron) are properly welded with the upper part of the structure pipes. welded bushing suppor
Rope Pump MANUFACTURING checklist for quality control A Welding General 1 Check if welding jigs are used for welding of the main parts (wheel, structure frame and bushings) 2 Check if the pump parts are
More informationInstallation Instructions for FC2 & FC15 Forward Controls for the Super Magna
Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationCopyright MLCS 1
Copyright 2007. MLCS 1 WORKING WITH BOX JOINTS Box joints (AKA "Finger Joints") provide a simple, yet equally effective, alternative to dovetail joinery. In particular, they serve well for applications
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationNew Jersey Electric Guitar DIY Kit
New Jersey Electric Guitar DIY Kit Thank you for purchasing this DIY Guitar Kit. The following instructions specify how to assemble your guitar. There are a variety of finishes that can be applied to the
More informationMODEL H9565 BALL BEARING GUIDE FOR G0513/G0514 INSTRUCTION SHEET
MODEL H9565 BALL BEARING GUIDE FOR G0513/G0514 INSTRUCTION SHEET Introduction The Model H9565 replaces the upper and lower Euro-style guides on your G0513 or G0514 Bandsaw. Inventory (Figure 1) A. Upper
More informationU-bass Kit Assembly Instructions
U-bass Kit Assembly Instructions Compiled by playubass.com This guide is built from the instructions found here: http://kalabrand.com/ubass-kit/index.html Tools Needed 5/8 (16 mm) Wrench 7/16 (~11 mm)
More informationCHAPTER 11 3/4" Box (Finger) Joints
53 RTJ400 OPERTION CHPTER 11 3/4" ox (Finger) Joints IMPORTNT SFETY NOTE efore using your Leigh RTJ400 you must have completed the preparatory steps listed in the previous pages, including reading the
More informationAdjustable Hammered Dulcimer Stand
Adjustable Hammered Dulcimer Stand Musicmaker s Kits (Hwy 36 behind Joseph s Restaurant) P.O. Box 2117 Stillwater MN 55082 651 439 9120 www.harpkit.com PARTS LIST: 1 Set of Assembly Instructions A. 2 front
More informationHQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1
HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included
More information1) Place the reactor stand on a sturdy bench with the bottom plate facing toward the front.
Assembly Instructions for ChemRxnHub Reactor Systems 1) Place the reactor stand on a sturdy bench with the bottom plate facing toward the front. Loosen knobs on the right and left using 2 hands of the
More informationKIT. Assembly Instructions. HayDay, LLC
KIT Assembly Instructions HayDay, LLC 1-800-732-1654 www.stablegrazer.com Read completely through the assembly instructions before starting assembly. The Stable Grazer Kit comes in two boxes. Remove all
More information25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
More informationElectric Guitar Kit DC Style electric guitar kit
Electric Guitar Kit DC Style electric guitar kit user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet:
More informationBrooklyn DIY Guitar Kit
Brooklyn DIY Guitar Kit Thank you for purchasing this DIY Guitar Kit. The following instructions specify how to assemble your guitar. There are a variety of finishes that can be applied to the guitar,
More informationKromski Minstrel Assembly Instructions
Kromski Minstrel Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU
More informationShoulder Plane. dovetailed. fine tools. Make an heirloom tool and learn the secret to creating double dovetails in metal it s easier than you think.
fine tools dovetailed Shoulder Plane Make an heirloom tool and learn the secret to creating double dovetails in metal it s easier than you think. I ve always been fascinated by old, metal hand planes.
More informationASSEMBLY INSTRUCTIONS
WWW.NUKE.ROCKS ASSEMBLY INSTRUCTIONS 1 Let s begin our satisfying journey to 3D Printed music by downloading a copy of Nuke s 3D model from www.nuke.rocks. You will obtain a ZIP file which you must decompress,
More informationHow to install backchecks
How to install backchecks Note: All pictures can be enlarged for better clarification. Revision 7 8/2009 Backchecks wear out in a piano much like brake pads in an automobile. While wear is a valid reason
More informationKossel Rev B Build Guide V1.0
Kossel Rev B Build Guide V1.0 1 Table of Contents: Step 1: BASE ASSEMBLY Gathering parts: Building the Corners and Base: Step 2: UPPER ASSEMBLY Building Upper: Step 3: VERTICAL RAIL INSTALLATION Building
More informationTools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More informationKromski Fantasia. Assembly Instructions
Kromski Fantasia Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU
More informationABM International, Inc.
ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket
More informationSolo AD Style DIY Acoustic Guitar Kit
Solo AD Style DIY Acoustic Guitar Kit Assembly Manual ADK-1 V 2.0 Copyright 2017 Solo Music Gear. All rights reserved Show Off Your Custom Built Guitar! When you have your guitar finished, please take
More informationHow to Build a Fretless, Acoustic Cigar Box Guitar
How to Build a Fretless, Acoustic Cigar Box Guitar Introduction Welcome to the fun and world of building Cigar Box Guitars. It is unlikely that you will build only one - it is addictive. Regardless of
More informationDYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0
DYNATRAC PRODUCTS 2007-2018 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0 WARNING: Improper use or installation of this product can cause major failures that
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationAdjustable Box Joint Jig. Richard Hicks on 8/24/2015. Box or Finger Joints
Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box or Finger Joints Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box Joints are also called Finger Joints Because they have interlocking fingers
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationModel PLM5113N PETROL LAWN MOWER
Strana 1 / 2 Strana 2 / 2 Strana 1 / 4 001 671006065 "BLADE TIGHTEN BOLT 3/8""24" 1 002 671010730 LID SHAPE WASHER 1 003 DA00000973 BLADE 510MM 1 004 671015252 BLADE SUPPORT 1 005 DA00000535 FLAT KEY 1
More informationINSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY
INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½
More informationExtendable Large Dovetail Jig
Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.
More informationNew Jersey Jr Electric Guitar DIY Kit
New Jersey Jr Electric Guitar DIY Kit Thank you for purchasing this DIY Guitar Kit. The following instructions specify how to assemble your guitar. There are a variety of finishes that can be applied to
More informationSERVICE MANUAL AND PARTSLIST
SERVICE MANUAL AND PARTSLIST Next 20 CONTENTS WHAT TO DO WHEN... 1~3 SERVICE ACCESS FACE COVER... 4 TOP COVER... 4 BASE COVER... 5 REAR COVER... 6 FRONT COVER... 7 MECHANICAL ADJUSTMENT NEEDLE THREAD TENSION...
More information12. Wings, Flaps, Ailerons and Struts
12. Wings, Flaps, Ailerons and Struts Fit Aileron Hinges Reference: Drawing 20270K2 Photo 12.1 Parts Required: 2007092 Aileron LS 200809N Aileron RS 2001394 Hinge 3/16 A1 (4) 2001694 Hinge Pin (4) PH0059N
More informationASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND GM FLUSH TAILGATE WITH HANDLE
ASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND 41-53 GM FLUSH TAILGATE WITH HANDLE Build the box assembly according to the MAR-K assembly instructions. When installing the tailgate and latching mechanisms
More informationINSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT
INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results
More informationDYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0
DYNATRAC PRODUCTS 2007-2016 4X4 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 WARNING: Improper use or installation of this product can cause major failures
More informationClock 35 - Toyland. Construction instructions for Clock 35
This clock has been designed for children, it is a stand-alone unit and can be positioned on a shelf or cabinet out of the reach of very young hands who may be tempted to touch. The clock is shown in two
More informationOwner s Manual e-guitar Kit sg-style Harley Benton E-Guitar Kit SG-Style
Owner s Manual E-Guitar Kit SG-Style Contents Introduction... 3 Body finish... 4 Neck finish... 4 Assembling of tuners... 5 Neck... 6 Wiring... 7 Bridge assembly... 10 Strap buttons... 11 Setting up...
More informationWARNING! ETCHED PARTS CONTAINED IN THIS KIT HAVE SHARP POINTS, EDGES AND CORNERS.
MPD18 chassis build instructions K A (see below for details) J I G H L C D F E B M Parts list: Ident Quantity A Etched Nickel/Silver fret 1 B Wheel sets 2 C Worms 2 D Worm gears 2 E Shaft adapters 2 F
More informationMODEL NO.: MI PARTS BREAKDOWN
MODEL NO.: MI-76350 PARTS BREAKDOWN MAGNUM DRILL PRESS ASSEMBLY INSTRUCTIONS MODEL MI-76350 Before you begin to assemble your drill press, review the parts breakdown and keep it ready for reference. Start
More informationFlush Trimmer Jig By Santanu Lahiri
Flush Trimmer Jig By Santanu Lahiri I found this jig in a book published by the Fine Woodworking people: Ingenious Jigs And Shop Accessories, publisher Taunton Press, ISBN# 1-56158-296-4. The Author is
More informationSatNOGS. SatNOGS Rotator v3 Mechanical Assembly. This is the assembly guide for the third version of the SatNOGS Rotator.
SatNOGS SatNOGS Rotator v3 Mechanical Assembly This is the assembly guide for the third version of the SatNOGS Rotator. Written By: Pierros Papadeas 2017 satnogs.dozuki.com Page 1 of 19 INTRODUCTION Notes:
More informationRACER TECH COMMANDER HD TIE ROD INSTALLATION
RACER TECH COMMANDER HD TIE ROD INSTALLATION NOTE: These instructions are a universal explanation of how to install our HD Tie Rods. All kits are identical for all inner joints and nearly identical for
More informationPrecision Steel Car s 100 T Steel Coil Car
Precision Steel Car s 100 T Steel Coil Car Precision Steel Car www.precisionsteelcar.com info@precisionsteelcar.com Paul Vernon: (513) 571-5739 Revised 4/30/2009 Contents of Kit Main Tube Side Frame 2
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationAUTO STABILIZING AND LEVELLING SYSTEM
Installation Manual Make sure the caravan is parked in a safe place. Make sure the caravan brake is on. Remove all 4 corner steady legs from the caravan. Remove the corner steady legs by removing the 3
More informationWant to make a travel scope but too lazy to read the whole thing? Read this:
My 114mm Travel Scope by Cyrille de Brebisson of Rhône-Alpes, France cyrille.de.brebisson@gmail.com During my last trip in the US, I was able to pick a 114mm/25.4mm primary/secondary mirror pair for 18$
More informationPROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0
DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could
More informationOwner s Manual. Bass-Guitar Kit J-Style
Owner s Manual Bass-Guitar Kit J-Style Contents Introduction... 3 Body finish... 4 Neck finish... 4 Assembling of tuners... 5 Neck... 6 Wiring... 6 Bridge assembly... 8 Strap buttons... 8 Setting up...
More informationAstro-Physics Inc. 400QMD Lubrication/Maintenance Guide
Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.
More information3D PRINTER. Pack 11. Anything you can imagine, you can make! 3D technology is now available for you at home! BUILD YOUR OWN
BUILD YOUR OWN Pack 11 Anything you can imagine, you can make! 3D PRINTER Compatible with Windows 7 & 8 Mac OS X 3D technology is now available for you at home! BUILD YOUR OWN 3D PRINTER CONTENTS PACK
More informationTHIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE
Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER
More informationthe wire, less is better. And make sure the bends on each truss wire are in line with the other. See the next photo.
The following information and photographs are what I did to build the kit. Your methods and needs may differ from this which is fine. There is no right or wrong way if you are used to scratch building.
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationCap frame (Shaft-less type)
Cap frame (Shaft-less type) Installation manual ** Model : XT-CAII / XT-CBII / XT-CII / XY-CII / XS-C ** 1: Wide cap frame -------------------------------------------------------------Page 2 2: Semi-wide
More informationCORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.
CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:
More informationTOOLS You will need some tools. Mostly, they re tools you probably have around the house, anyway.
INTRODUCTION Congratulations on your purchase of your RAS Kit. While it can be a great challenge for an inexperienced builder, with care and attention to details, it can produce an excellent instrument
More informationSECTION 9: PARTS Main
SECTION 9: PARTS Main 58 63 67 66 65 67 66 59 58 49 58 48 49 61A 61 64 62 55 50 35-3 34 35-1 57 56 41 42 151 51 50 33A 35-2 30A 30A-1 35 38 39 31 32 18 40 43 44 68 51 41 45 46 57 56 55 47 152 153 20 21
More informationPost-Paint>Fuselage>Interior>Controls>Fit rudder pedals
Post-Paint>Fuselage>Interior>Controls>Fit rudder pedals Objectives of this task: To fit the rudder pedals and steering links to the aircraft, and fit the rudder cable to the rudder pedals and set the deflection
More informationChain Drive Vise. Installation Instructions. (revised 05/04/2016)
Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationTOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.
THIS KIT INCLUDES: 16 M8-1.25X30MM BOLTS WITH WASHERS 2 SHOCKS 565 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 7/23, 10MM,
More information(2) 25mm x 20mm x 5mm Adhesive Backed Foam Pads. 100mm x 50mm x 1.0mm Adhesive Backed Foam. (2) Spacer Plates. Passenger/Right Side Frame Mounting
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Frame Mounting 16 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Frame Mounting 8 12mm Hex Nuts 1 Driver/Left Side Top Support 2 10-1.50mm
More informationTHE PODIUM MUSIC STAND
THE PODIUM MUSIC STAND 1 Set Assembly Instructions Wooden Parts: a. 1 Column b. 2 Long Slide Pieces c. 2 Slide Spacers (1 long & 1 short) d. 4 Feet e. 2 Fork Pieces f. 1 Fork Spacer g. 2 Long Desk Frame
More informationTROLLA LEAVY 97 CM Lawn sweeper
TROLLA LEAVY 97 CM Lawn sweeper Artikel nr.: 1008 EN Operating manual 014/1 Dear Customer, Congratulations on your new Trolla product. We hope you will enjoy it. Checkout with your new Trolla product may
More informationMP573 Assembly guide. Soldering. MP573 Assembly guide PCB split PCB split. Document revision 2.2 Last modification : 22/08/17
MP573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationINSTRUCTIONS AND PARTS LIST POWER HAMMER
INSTRUCTIONS AND PARTS LIST POWER HAMMER DAKE (Division of JSJ) 724 Robbins Road Grand Haven, Michigan 49417 616.842.7110 Phone 800-937-3253 616.842.0859 Fax 800-846-3253 Web: www.dakecorp.com E-mail :
More informationCHIPPER SHREDDER H524H, HS24W AHS24H, AHS24W Parts Catalog
R Ingersoll CHIPPER SHREDDER H524H, HS24W AHS24H, AHS24W Parts Catalog 8-3291 HOME TRACTORS ATTACHMENTS PAINT GENERAL INFO ALPHABETICAL Body, Hopper and Shredder Hammers...5 Chipper Assembly...7 Trailer
More informationBefore use please read & understand this manual, paying particular attention to the safety instructions.
OPERATOR S MANUAL AND PARTS LIST 12 HAND PUSH ROLLER MOWER - THHMR Sales & Helpline 01793 333220 www.thehandy.co.uk Before use please read & understand this manual, paying particular attention to the safety
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationAssembly instructions for Classic Cantabile DIY Ukulele
Assembly instructions for Classic Cantabile DIY Ukulele ArtNr.: 00036326 Sopranukulele / 00036327 Konzertukulele Musikhaus Kirstein GmbH Bernbeurener Strasse 11 D-86956 Schongau / Germany Tel.: 0049-8861-909494-0
More informationInstallation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100
Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationThe IntoPlay build. This section will show how to fill the components into the case halves, and also the case base, which will look like this:
The IntoPlay build Ok, I presume you have read the sections about cutting the holes in the case front, speaker holes and spray painting, modding components, preparing the case, etc. So far, the guides
More informationINSTALLATION INSTRUCTIONS CHEVY C-10 INDEPENDENT FRONT SUSPENSION
INSTALLATION INSTRUCTIONS 73-87 CHEVY C-10 INDEPENDENT FRONT SUSPENSION Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationSlicing Jig For Pen Inlays
Slicing Jig For Pen Inlays By Randall Smith (randyrls) May 2008 This article has been downloaded from the library of the International Association of Penturners. www.penturners.org You are welcome to reproduce
More informationSECTION 9: PARTS Jointer Breakdown
Model G0490/G0490X (Mfd. Since 8/12) -49-1 3 8 7 9 12 14 15 16 18 21 23 24 24 28 29 32 33 37 38 38 44 45 49 50 51 53 55 56 57 58 59 61 60 64 65 66 68 72 75 80 81 82 83 84 85 86 87 88 90 91 92 94 93 96
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationDesktop Trebuchet Kit Assembly Instructions
Desktop Trebuchet Kit Assembly Instructions Contents of package (drawings are not to scale for clarity, parts that have duplicates are indicated with total number of that part to be found, example: 2X
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationREPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationWOLF PUP LOOM TM & WOLF PUP LT LOOM TM
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212
More informationInterior CHAPTER 21. Phantom Roadster Instruction Manual 273
CHAPTER 21 Interior When you get to this chapter you are now starting on the finish that will make your car one that will be complete your hard work. This chapter will cover the installation of the door
More informationIt is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating loose.
Installation instructions for FC12 Forward Controls for Kawasaki Vulcan 750 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationMODEL T21973 METAL BLADE GUIDE SET INSTRUCTIONS
MODEL T21973 METAL BLADE GUIDE SET INSTRUCTIONS Introduction (Figure 1) These Euro-style blade guides replace the blade guides on the G0531, G0531B, G0566, G0568, and G0569 bandsaw. Tools Needed Wrench
More informationCopyright 2007 MLCS 1
Copyright 2007 MLCS 1 REFERENCE GUIDE and SPECIFICATIONS: Edge Guides: This 12 Dovetail Template comes complete with 2 Edge Guide Sets one set for Half Blind and one set for Rabbeted Half Blind Dovetails.
More informationMODEL NO.: MI / 42100
MODEL NO.: MI-50 / 00 MODEL NO.: MI-50 BOX 1 OF 6 ROUTER LIFT PARTS BREAKDOWN Router Lift Assembly 6 5 2 2 1 5 5 8 12 11 2 26 27 0 12 26 27 27 22 22 27 19 A 5 26 12 26 22 25 25 7 18 18 15 15 7 9 1 17 2
More informationSCHWERE PLATTFORMWAGON TYPE SSY 60TON
TWS 5094 SCHWERE PLATTFORMWAGON TYPE SSY 60TON Congratulations on purchasing one of the finer aftermarket resin kits sets available. The photo below is of the completed kit. The Panther tank is not included
More informationG0513X2 Main -87- G0513 Series Bandsaws 82V V2 82-6V2 95A V2 82-5V2 82-1V2 82-4V V A
G0513X2 Main 23 55 22 48 17 17-1 17-2 21 7 17-3 17-2 17-4 24 17-5 18-5 22 24 21 55A 50 8 9 49 11 12 13 14 15 47 16 10 46 45 3 44 43 39 38 37 39 40 32 33 36 42 34 35 2 25 28 18-4 18-2 18-3 31 30 29 18-1
More informationSolo JB Style DIY Electric Bass Guitar Kit
Solo JB Style DIY Electric Bass Guitar Kit Assembly Manual JBK-1 V 1.02 Copyright 2011 Solo Music Gear. All rights reserved Materials List Press-fit peghead bushings String Retainer (1 mounting screw included)
More informationINSTRUCTIONS FOR HIT LOCK MORTISER
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-200 LOCK MORTISER WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR
More informationCoil Winder Instructions.
Page Coil Winder Instructions. Before we can build our wind turbine there are a few tools we need to make. We ll need to make moulds for the magnet rotors and the stator, and we need to make a coil winder.
More information