DEWALT 210 Bath Road Slough, Berks. SL1 3YD. Tel: Fax: DE6242. Copyright DEWALT

Transcription

1 DEWALT 210 Bath Road Slough, Berks. SL1 3YD Tel: Fax: DE /06 Copyright DEWALT

2 IFU ADDITIONAL EQUIPMENT REQUIRED: Cutting to Length for 45 Joints only ELECTRIC HAND ROUTER 30mm ROUTER GUIDE BUSH TUNGSTEN CARBIDE ROUTER CUTTER mm DIA X 50mm (1/2 DIA X 2 ) MINIMUM OF 2 QUICK ACTION, G CLAMPS OR SCREW CLAMPS 1000mm When producing a male joint, left or right handed and where the worktop turns through 45, the position of the cut jig has to be calculated. It is easier if the female joint is cut first, leaving the gap intended for the male part of the worktop. Slot for screw clamp Holder for flush fitting location pegs Edge of jig to cut indicator For 500, 600, 616, , 720, 740, 900 & 920mm Wide Worktops FACE 1 Left & Right Hand 90 Joints Example The female joint has already been cut (see left diagram) and the length of the male worktop needed is 1000mm (1 metre). Position your worktop jig onto the laminate referring back to the instructions on 45 joints. Subtract 293mm from the intended length - (this dimension is engraved on the jig and relates to the distance from the bottom edge of the jig to where the edge of the cut will be). E.g. 1000mm 292 = 708mm Position the worktop jig 708mm from the opposite end of the laminate you re cutting (see bottom left diagram) After the cut, a 1000mm length laminate is left. Change the 1000mm figure used in this example for whatever length you require. Slot for screw clamp DE6289 FACE 2 Left & Right Hand 45 Edge of jig to cut indicator Carrying Handle Rout recesses for Worktop Connecting Bolts 708mm 1000mm Denotes Denotes Male Page 2 Page 15

3 1. MALE JOINT Prepare the male worktop with the laminate face up. 2. Insert 2 pins in holes marked Refer to the page on cutting to length on page 15 to find out where to mark the pencil line to determine the position of the jig along the length of the worktop. 4. Make sure the 2 pins in the holes marked 45 are firmly pushed against the post formed edge (see diagram X) 5. Clamp the jig to the worktop checking that both pins are still against the worktop. Make sure the clamps will not obstruct the router path. 6. Follow steps 6 to 10 for cutting the worktop. Right Hand 45 Male Joints DIAGRAM X MALE JOINT- LAMINATE FACE UP Protecting the Environment Separate Collection This product must not be disposed of with normal household waste. Should you find one day that your DEWALT product needs replacement, or it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows material to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. 7. CUTTING METHOD Position the router in the far left side of the slot. Set the router to cut a depth of 10mm. 8. IMPORTANT - Position the router in the slot and cut from left to right, pulling the router against the edge of the slot closest to you. 9. Remove the router, and start again from the far left of the central slot, but increase the depth a further 10mm. DIAGRAM Y 10. Follow steps 7 9, until cut is complete. For the final finishing cut, position the router again in the far left side of the slot, and set the router to cut at the full depth of the worktop. Again, cut from left to right but apply the pressure to the edge furthest away from you Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. DEWALT provides a facility for the collection and recycling of DEWALT products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent at the address indicated in this manual. Alternately, list of authorised DEWALT repair agents and full details of our after-sales service and contacts are available on the internet at: DIAGRAM Z MALE JOINT- LAMINATE FACE DOWN 11. MALE BOLT RECESSES Prepare the male worktop with the laminate face down. 12. Insert 3 pins in the holes marked B. 13. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop (see diagram Z). 14. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 15. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 16. Cut the bolt recesses out, each time clearing the waste material after each cut. Page 14 Page 3

4 GUARANTEE Right Hand 45 Joints ONE YEAR FULL WARRANTY If your DEWALT product becomes defective due to faulty materials or workmanship within 12 months of the date of purchase, we will guarantee to replace all defective parts free of charge or, at our discretion, replace the unit free of charge provided that: The products was not misused. Repairs have not been attempted by unauthorised persons. Proof of purchase date is produced. This guarantee is offered as an extra benefit and is additional to consumers statuary rights. 1. FEMALE JOINT Refer to the diagrams on the different joints available. 2. Prepare the female worktop with the laminate face down and the post formed (curved edge) towards the left. 3. Insert 2 or 3 pins in the holes marked 45 (see diagram T) 4. Slide the jig along the length of the worktop so that when cut is made, the joint face is a little longer than the worktop width. Once the jointing face has been cut, there will be enough length for the male worktop to fit (minor adjustment may be necessary (see diagram P). Worktop Width DIAGRAM T FEMALE JOINT- LAMINATE FACE DOWN For the locations of your nearest authorised DEWALT repair agent, please use the appropriate telephone number on the back of this manual. Alternatively, a list of authorised repair agents are available on the internet at DIAGRAM U 5. Make sure the 2 or 3 pins in the holes marked 45 are firmly pushed against the front post formed edge. 6. Clamp the jig to the worktop checking that both pins are still against the worktop. Make sure the clamps will not obstruct the router path. 7. Once the cut is complete, cut off the excess (Diagram V), so that the distance from point 1 to point 2 is equal to your worktop width. Cut off DIAGRAM V FEMALE JOINT TRIM WORKTOP 8. CUTTING Position the router in the far left side of the central slot. Set the router to cut a depth of 10mm. 9. IMPORTANT - Position the router in the slot and cut from left to right, pulling the router against the edge of the slot closest to you. 10. Remove the router, and start again from the far left of the central slot, but increase the depth a further 10mm. 11. Follow steps 8 10, until cut is complete. 12. For the final finishing cut, position the router again in the far left side of the central slot, and set the router to cut at the full depth of the worktop. Again, cut from left to right but apply the pressure to the edge furthest away from you. Page 4 Point 1 Point FEMALE BOLT RECESSES Prepare DIAGRAM W the female worktop with the laminate FEMALE BOLT RECESS - face down. 14. Insert 3 pins in the holes marked B (see diagram W). 15. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop. 16. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 17. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 18. Cut the bolt recesses out, each time clearing the waste material after each cut.. Page 13

5 Left Hand 45 Male Joints Safety Notes 1. MALE JOINT Prepare the male worktop with the laminate face down. 2. Insert 2 pins in holes marked Refer to the page on cutting to length on page 15 to find out where to mark the pencil line to determine the position of the jig along the length of the worktop. 4. Make sure the 2 pins in the holes marked 45 are firmly pushed against the post formed edge (see diagram Q) 5. Clamp the jig to the worktop checking that both pins are still against the worktop. Make sure the clamps will not obstruct the router path. 6. Follow steps 6 to 10 for cutting the worktop. DIAGRAM R DIAGRAM Q MALE JOINT - 7. CUTTING METHOD Position the router in the far left side of the slot. Set the router to cut a depth of 10mm. 8. IMPORTANT - Position the router in the slot and cut from left to right, pulling the router against the edge of the slot closest to you. 9. Remove the router, and start again from the far left of the central slot, but increase the depth a further 10mm. 10. Follow steps 7 9, until cut is complete. 11. For the final finishing cut, position the router again in the far left side of the slot, and set the router to cut at the full depth of the worktop. Again, cut from left to right but apply the pressure to the edge furthest away from you. Before starting... Never cut worktop to length until all joints are complete and have been checked for correct fit. Make sure the worktop is secured firmly to the bench or trestle. Ensure that the jig is firmly secured to the worktop. Ensure there are no obstructions in the path of the router e.g. clamps or bench. Always use good quality sharp router bits Always wear eye protection when cutting. Always wear ear protection if cutting for long periods Always cut from left to right. Always cut into post formed edge to avoid breakout or chipping. Always keep the router vertical to the jig and worktop. Never exceed 10mm depth of cut in one pass. Never remove the router from the jig or position the router whilst cutter is still rotating. The cutter may cut into the jig and damage the bush location faces. This jig will enable you to cut. STANDARD LEFT & RIGHT HAND 90 JOINTS DIAGRAM S MALE BOLT RECESS MALE BOLT RECESSES Prepare the male worktop with the laminate face down. 13. Insert 3 pins in the holes marked B. 14. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop (see diagram S). 15. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 16. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 17. Cut the bolt recesses out, each time clearing the waste material after each cut. Male Male 45 JOINTS - RIGHT AND LEFT HAND Male Male Male CORNER JOINT - USING THE RIGHT HAND AND LEFT HAND 45 JOINTS Page 12 Page 5

6 90 Joints - Left Side 1. FEMALE JOINT Refer to the diagrams on the different joints available. 2. Prepare the female worktop with the laminate or sealed prepared surface, face up and the post formed (curved edge) towards you. 3. For all 90 joints, the jig should be placed with the logo uppermost. 4. Insert 3 pins in the holes marked. DIAGRAM A FEMALE JOINT - LAMINATE FACE UP 5. Insert the 4th pin in the hole dependant on your worktop width. e.g. As in the example shown, if your worktop is 700mm wide then insert the 3rd pin in the hole marked 700 (see diagram A). 6. Make sure the 3 pins in the holes marked with are firmly pushed against the front post formed edge and the pin in the hole marked with the worktop width is pushed firmly against the edge of the worktop (see diagram A) 7. Clamp the jig to the worktop checking that all 3 pins have not moved away from the worktop. Make sure the Using Screw clamp DE6289 DIAGRAM B Using G-clamp 8. CUTTING METHOD Position the router in the far left side of the slot. Set the router to cut a depth of 10mm. 9. IMPORTANT - Position the router in the slot and cut from left to right, pulling the router against the edge of the slot closest to you. 10. Remove the router, and start again from the far left of the central slot, but increase the depth a further 10mm. 11. Follow steps 8 9, until cut is complete. 13. FEMALE BOLT RECESSES DIAGRAM C Prepare the female worktop with FEMALE BOLT RECESS - the laminate or prepared surface. face down. 14. Insert 3 pins in the holes which are marked B. 15. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop (see diagram C). 16. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 17. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 18. Cut the bolt recesses out, each time clearing the waste material after each cut. 1. FEMALE JOINT Refer to the diagrams on the different joints available. For 45 joints the jig should always be placed with the logo facing down. 2. Prepare the female worktop with the laminate face up and the post formed (curved edge) towards the left. 3. Insert 2 or 3 pins in the holes marked 45 (see diagram M) 4. Slide the jig along the length of the worktop so that when cut is made, the joint face is a little longer than the worktop width. Once the jointing face has been cut, there will be enough length for the male worktop to fit (minor adjustment may be necessary (see diagram O). 9. IMPORTANT - Position the router in the slot and cut from left to right, pulling the router against the edge of the slot closest to you. 10. Remove the router, and start again from the far left of the central slot, but increase the depth a further 10mm. 11. Follow steps 8 10, until cut is complete. 12. For the final finishing cut, position the router again in the far left side of the central slot, and set the router to cut at the full depth of the worktop. Again, cut from left to right but apply the pressure to the edge furthest away from you. 13. FEMALE BOLT RECESSES Prepare the female worktop with the laminate face down. DIAGRAM P FEMALE BOLT RECESS - Left Hand 45 Joints DIAGRAM N Worktop Width 5. Make sure the 2 or 3 pins in the holes marked 45 are firmly pushed against the front post formed edge. 6. Clamp the jig to the worktop checking that both pins are still against the worktop. Make sure the clamps will not obstruct the router path. 7. Once the cut is complete, cut off the excess (Diagram O), so that the distance from point 1 to point 2 is equal to your worktop width. 8. CUTTING Position the router in the far left side of the central slot. Set the router to cut a depth of 10mm. DIAGRAM O FEMALE JOINT TRIM WORKTOP DIAGRAM M FEMALE JOINT- LAMINATE FACE UP Point 1 Point 2 Cut off 14. Insert 2 pins in the holes marked B and 1 pin into the hole marked with a B and 45. (see diagram P). 15. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop. 16. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 17. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 18. Cut the bolt recesses out, each time clearing the waste material.after each cut. Page 6 Page 11

7 Cutting to Length for 90 Joints only 90 Male Joints - Left Side 1000mm Intended location of worktop with male cut When producing a male joint, left or right handed and where the worktop turns through 90, the position of the cut jig has to be calculated. It is easier if the female joint is cut first, leaving the gap intended for the male part of the worktop. Example The female joint has already been cut (see left diagram) and the length of the male worktop needed is 1000mm (1 metre). Position your worktop jig onto the laminate referring back to the instructions on 90 joints. Subtract 277mm from the intended length (this dimension is engraved on the jig and relates to the distance from the bottom edge of the jig to where the edge of the cut will be). E.g. 1000mm 277 = 723mm Position the worktop jig 723mm from the opposite end of the laminate you re cutting (see bottom left diagram) After the cut, a 1000mm length laminate is left. Change the 1000mm figure used in this example for whatever length you require. DIAGRAM D MALE JOINT LAMINATE FACE DOWN DIAGRAM E 1. MALE JOINT Prepare the male worktop with the laminate or prepared surface face down. 2. Insert 2 pins in holes marked Refer to the page on cutting to length on page 10 to find out where to mark the pencil line to determine the position of the jig along the length of the worktop. 4. Make sure the 2 pins in the holes marked 90 are firmly pushed against the post formed edge (see diagram D) 5. Clamp the jig to the worktop checking that both pins are still against the worktop. Make sure the clamps will not obstruct the router path. 6. CUTTING METHOD Position the router in the far left side of the slot. Set the router to cut a depth of 10mm. 7. IMPORTANT - Position the router in the slot and cut from left to right, pulling the router against the edge of the slot closest to you. 8. Remove the router, and start again from the far left of the central slot, but increase the depth a further 10mm. 9. Follow steps 6 8, until cut is complete. 10. For the final finishing cut, position the router again in the far left side of the slot, and set the router to cut at the full depth of the worktop. Again, cut from left to right but apply the pressure to the edge furthest away from you. 723mm 1000mm DIAGRAM F MALE BOLT RECESS MALE BOLT RECESSES Prepare the male worktop with the laminate or prepared surface face down. 12. Insert 2 pins in the holes marked B and 1 pin in the hole marked with both a B and 90. (see diagram F). 13. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop. 14. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 15. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 16. Cut the bolt recesses out, each time clearing the waste material after each cut. Page 10 Page 7

8 90 Joints - Right Side 1. FEMALE JOINT Refer to the diagrams on the different joints available. Prepare the female worktop with the laminate face down and the post formed (curved edge) towards you. DIAGRAM G FEMALE JOINT - 2. Insert 3 pins in the holes marked. 3. Insert the 4 th pin in the hole dependant on your worktop width, e.g. If your worktop is 700mm wide then insert the 4 th pin in the hole marked 700 (see diagram G). 4. Make sure the 3 pins in the holes marked F are firmly pushed against the front post formed edge and the pin in the hole marked with the worktop width is pushed firmly against the edge of the worktop. 5. Clamp the jig to the worktop double-checking that all 4 pins are still against the worktop. Make sure the clamps will not obstruct the router path. 90 Male Joints - Right Side 1. MALE JOINT Prepare the male worktop with the laminate face up. 2. Insert 2 pins in holes marked 90. (see diagram J) 3. Refer to the page on cutting to length to find out where to mark the pencil line to determine the position of the jig along the length of the worktop. 4. Make sure the 2 pins in the holes marked 90 are firmly pushed against the post formed edge. 5. Clamp the jig to the worktop checking that both pins are still against the worktop. 6. Make sure the clamps will not obstruct the router path. DIAGRAM J MALE JOINT LAMINATE FACE UP DIAGRAM K 7. CUTTING METHOD DIAGRAM H 6. CUTTING METHOD 8. Refer to the instructions on page 7 for cutting method. 7. Refer to the instructions on page 6 for cutting method. 8. FEMALE BOLT RECESSES Prepare the female worktop with the laminate face down. 9. Insert 3 pins in the holes marked B (see diagram C). 10. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop (see diagram I) 11. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 12. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 13. Cut the bolt recesses out, each time clearing the waste material after each cut. DIAGRAM I FEMALE BOLT RECESS MALE BOLT RECESSES Prepare the male worktop with the laminate face down. 10. Insert 2 pins in the holes marked B and 1 pin in the hole marked with both B and 90.(see diagram L). 11. Make sure the 3 pins are firmly pushed against the front cut out and the edge of the worktop. 12. Clamp the jig to the worktop checking that all 3 pins are still firmly against the worktop. Make sure the clamps will not obstruct the router path. 13. You will need a depth of 20mm for the worktop connectors. Do not exceed 10mm per cut. 14. Cut the bolt recesses out, each time clearing the waste material after each cut. DIAGRAM L MALE BOLT RECESS. Page 8 Page 9