Presentation Outline Pipe types and Standards
|
|
- Jeffry Lloyd
- 5 years ago
- Views:
Transcription
1 Pipe Joint Assembly and Restraint Considerations Jeff Fischer Fischer, Harris and Associates Presentation Outline Pipe types and Standards Pipe Joint Assembly Joint Restraint and Thrust Blocks Products for Joint Restraint Joint Restraint Applications 1
2 Wood Pipe Circa 1900 More wood pipe. 2
3 Wood Pipe Today 3
4 UL-FM ASTM NSF EPA DIPRA UNI-BELL Manufacturer Engineer You AWWA/ANSI C110/A21.10: Ductile Iron and Gray Iron Fittings, 3 in. through 48 in. For Water and Other Liquids AWWA/ANSI C153/A21.53: Ductile Iron Compact Fittings, 3 in. through 24 in. and 54 in. through 64 in. for Water Service AWWA/ANSI C111/A21.11: Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings AWWA/ANSI C104/A21.4: Cement-Mortar Lining for Ductile-Iron Pipe and Fittings for Water AWWA/ANSI C116/A21.16: Protective Fusion Bonded Epoxy Coatings for the Interior and Exterior Surfaces of Ductile-Iron and Gray-Iron Fittings for Water Supply Service AWWA/ANSI C105/A21.5: Polyethylene Encasement for Ductile- Iron Pipe Systems AWWA/ANSI C600: Installation of Ductile-Iron Water Mains and their Appurtenances 4
5 Standard Pipe Joints Ductile Iron Push On 5
6 PVC Push On Water and Sewer Standards AWWA C900 AWWA C905 AWWA C909 ASTM D2241 ASTM D3034 6
7 Installation 7
8 Bell Stress Research Analytical Model of Stresses Caused by Over-Belling PVC Pipe Steven L. Folkman, Associate Professor, Utah State University A. P. Moser, Emeritus Associate Dean and Emeritus Professor, Utah State University Thomas Fronk, Associate Professor, Utah State University Manufacturers of large diameter PVC pipe place a mark on the spigot of the pipe to indicate the proper insertion depth into the adjoining bell during installation. If proper installation procedures are followed, inserting the spigot into the bell does not create significant stresses in the pipe. Additionally, small angle changes between two joined pipes may be accommodated in the joint without inducing pipe stresses. When pipe joint failures occur, in most instances the pipe was inserted well beyond the manufacturers recommended mark. This is referred to as Over-Belled pipe. Recommended Bar Assembly 8
9 Assembly Force Joint Stacking Even this method can over-insert previously assembled joints 9
10 5/4/ :33 PM 20 10
11 Standard Pipe Joints Flanged Normally Installed Above Ground Inherently Restrained Most pipe types offer a flanged joint of some kind. Jargon confusion by many pipe- fitters Other Flanged Pipe Materials Stainless Steel PVC HDPE Industrial Applications 11
12 1866 First Cast Iron Pipe in US History 1894 First Flange Standard 1894 (steam) 1918 Flange bolt patterns standardized 1957 Introduction of Ductile Iron Pipe and Flanges AWWA ANSI Standard adopted in 1974 Latest Revision 2005 Flange Materials For Water and Wastewater Cast Iron Threaded Ductile Iron Threaded Steel/Stainless Steel - Welded HDPE-Welded 12
13 Applicable Standards AWWA C110-C115-C207 ASME American Society of Mechanical Engineers MSS (Manufacturers Standards Society) UL-FM Flanges for Water Service Pipe and Fittings Valves Meters Tapping Sleeves Hydrants? 13
14 Thickness Flange Variations Varies from product to product Varies from manufacturer to manufacturer Serrations Cast and Ductile Iron, no AWWA standard Steel and Stainless, 32 per inch 1/64 deep spiral or concentric per AWWA Facing-Raised or Flat Cast and Ductile Iron no AWWA Standard Steel and Stainless Steel no raised face per AWWA Steel Flange Layback after welding of the flange has been completed, a draft or layback of the flange face may occur as shown in Figure 2 Total draft of layback shall not exceed 1-1/2 degrees...negative draft will not be permitted. Reference: AWWA C
15 Flange Fittings configurations Flange Gaskets Full Faced Red Rubber Cloth Inserted Rubber Ring Gaskets Hybrid Gaskets Linebacker 15
16 Bolting Carbon Steel Hex Head Grade Lubricant Recommended Stainless Steel Hex Head Grade Lubricant Required Pressure Ratings and Drillings Class 125/ for temps up to 100 df Class 250/ for temps up to 100 df 16
17 Flange Adaptors and Spool Sections Pipe can be cut in the field to exact length required Avoids long lead times and unused sections of pipe Speeds installation time resulting in lower job costs FCA Application 17
18 Flange Coupling Adaptor Attached to Pipe Plain End Pipe is lowered into postion 18
19 Gap Flange Adaptor Side by Side with a Traditional Flange 19
20 Flange Adaptor Types UniFlange, EZ Flange, Quick Flange Dismantling Joint Fittings Couplings Glue On (PVC) Fuse On (HDPE) Serrated Clamp (PVC) Megaflange Restraint Considerations Reference: Smith-Blair.com 20
21 Flange Coupling Adapter (EZ-Flange/Uni-Flange TM ) Fischer, Harris & Associat es Dismantling Joints Reference: Smith-Blair.com Provide adjustability to equipment installations by combining a flange coupling adaptor and a flanged spigot into one assembly Applications include valves, pumps, meters or other flanged equipment that may need to be removed periodically Longitudinal adjustment is provided by the telescoping action of the spigot inside the flanged coupling adaptor. Restrained model available. 21
22 FCA for Poly Reference: Coupling Type Adaptor Smith Blair 912 Epoxy Coated Ductile Insulating Option Available Short laying length Anchor studs for restraint Reference: Smith-Blair.com 22
23 Mega-Flange Type Restrained Flange Adaptor Available through 48 Allowable Gap Can be used as a dismantling joint Pipe need not be cut perfectly square Deflection up to 5% Can use above or below ground Reference: EBAA Iron.com Cross Section Reference: EBAA Iron.com 23
24 For Buried Flanged Valves Tank Connections 24
25 Standard Pipe Joints Mechanical Joint Mechanical Joint Cross Section 25
26 ANSI/AWWA C600-05, Mechanical Joint Assembly 1.Clean the socket and the plain end. Lubrication and additional cleaning should be provided by brushing both the gasket and the plain end with soapy water or an approved pipe lubricant meeting the requirements of ANSI/AWWA C111/A21.11 just prior to slipping the gasket onto the plain end for joint assembly. Place the gland on the plain end with the lip extension toward the plain end, followed by the gasket with the narrow edge of the gasket toward the plain end. NOTE: In cold weather it is preferable to warm the gasket to facilitate assembly of the joint ANSI/AWWA C600-05, Joint Assembly 2. Insert the pipe into the socket and press the gasket firmly and evenly into the gasket recess. Keep the joint straight during assembly. 3. Push the gland toward the socket and center it around the pipe with the lip against the gasket. Insert bolts and hand tighten nuts. Make deflection after joint assembly but before tightening bolts. 26
27 ANSI/AWWA C600-05, Joint Assembly 4. Tighten the bolts to the normal range of bolt torque [see table] while at all times maintaining approximately the same distance between the gland and the face of the flange at all points around the socket. This can be accomplished by partially tightening the bottom bolt first, then the top bolt, next the bolts at either side, finally the remaining bolts. Repeat the process until all bolts are within the appropriate range of the torque. ANSI/AWWA C
28 Lubrication of Mechanical Joints Friction Fischer, Harris & Associat es 28
29 29
30 Joint Restraint why do we use it? Balanced Forces Unbalanced Forces 30
31 31
32 How much thrust force is generated by a Water Pipeline? 12 DIP End Cap-150 psi Pi x Radius Squared 3.14 X 36=113 Area x pressure (PSI) 113 x 150 = 17,000 pounds of force How do we resist that force? Concrete Thrust Blocks Threaded Steel Rod Mechanical Restrainers Combinations of the above Fischer, Harris & Associat es 32
33 Fischer, Harris & Associat es 60 sq. ft. Building Thrust Blocks 33
34 Thrust Block Limitations Undisturbed soil? Contractor skill? Future connections? Concrete cure time? Vertical offsets? Sand and Swamp? Fischer, Harris & Associat es Threaded Rod Limitations High Cost Materials and Labor Corrosion Concerns Friction Clamps Fischer, Harris & Associat es 34
35 Fischer, Harris & Associat es Mechanical Restrainers Locking a pipe/fitting joint(s) together with a mechanical device designed to withstand pressures higher than normally expected to insure will not pull out at typical pressure. Fischer, Harris & Associat es 35
36 Using a high quality joint restraint device will ensure That the pipe will not pull out of the fitting. Making thrust blocks optional! Fischer, Harris & Associat es If you lock together a sufficient length of pipe, in essence it becomes it s own thrust block. 36
37 Calculating Restrained Length EBAA L Fischer, Harris & Associat es Fitting Types Supported by EBAA Design Software Tees Reducers Bends Dead Ends Vertical Offsets 37
38 38
39 39
40 40
41 Retainer Glands Pipe Joint Restraint Devices for DIP Pipe Company built-ins Wedge Action Restrainers Bell Joint Restraints Fischer, Harris & Associat es Retainer Glands Inexpensive Minimum pipe class required by some MFG Drills small hole in pipe Rigid joint will not accommodate pipe movement Low pressure rating on large diameters Cumbersome installation procedure. Fischer, Harris & A ssoc ia tes 41
42 Pipe Companies Restraints US Pipe TR Flex Field Lok Field Lok 350 HD Lok Pac States - Thrust Lock PVC Pipe Certa Lock Bulldog Clow - Super Lock ACIPCO Fastite Flex Ring Lock Ring Fast Grip Field Flex Ring MJ Coupled Joint Griffin Snap Lok Mech Lok Bolt Lok 5/4/2012 Fischer, Harris & Associat es Non-Pipe Company Wedge Action Mechanical Joint Restraints EBAA Iron Megalug Ford Blockbuster Star Stargrip Tyler-Tuf Grip Romac Romagrip Sigma One Lock Smith Blair Cam Lock Sigma - PV Loc Fischer, Harris & Associat es 42
43 Mueller AquaGrip Tyler MJ Field Lock JCM 600 Series Smith Blair - Maxi Grip Romac Grip Ring One Bolt Friction Clamps Non - Wedge Action Restrainers All Trademarked names Fischer, Harris & Associat es How many different joint ways are there to restrain a joint? 43
44 Price Availability 44
45 Ease of Assembly Fischer, Harris & Associat es Quality Ductile Iron Ductile Iron is a composite metal that has special properties Ductile Iron Grey/Cast Iron A Little of both 45
46 Country of Origin From the Chelvis Website For the first time, the magnificent home of Chelvis has been made available to tour by the public. This 16 Acre estate which Chelvis has named Riceland, houses a full service laundromat, a 2 story rickshaw garage, as well as of course an all you can eat Chinese buffet. Riceland attracts 5 to 10 visitors a year from all over the world. 46
47 Reliable and Repeatable Installations Friction can interfere with the contact pressure of the wedge to pipe interface if the threaded parts are corroded or coated with thick asphaltic coatings Joint Restraints for for Ductile Iron Pipe Installation ease - Use AWWA C-600 to make seal then twist off lug bolt heads to restrain. Color Coded - Black Body, Blue Wedges Quality - Date and Production Coded-Proof of Metallurgy on Every Product (Made in USA?) Strength psi through above that Reliability Powder coatings on casting and Flourocarbon Coated Threaded Parts. 47
48 Joint Restraints for PVC pipe Installation ease - Use AWWA C-600 to make seal then twist off lug bolt heads to restrain. Color Coded Red Body, Blue Wedges Quality - Made in USA- Date and Production Coded-Proof of Metallurgy on Every Product Strength Rated the same as the pipe itself Reliability -Standard MEGABOND coating including Xylan Coated Threaded Parts. Joint Restraints for Push on Pipe EBAA Bell Harness Series
49 Joint Restraint for Couplings Hybrid-Coupling/Sleeve Restrained Sleeve for either Ductile Iron, PVC or Steel Pipe 49
50 1100 series Megalug Cast Iron-Grey Iron Pipe Restraint Needs to be structurally sound pipe Can ordered for oversized pipe Coated Gray for identification Technical Paper Available SPLIT Restraints 50
51 Polyethylene Pipe Restraint Considerations Expansion, Contraction and the Poisson effect can cause significant pipe movement. Fischer, Harris & Associat es Pipe on Bridge Crossings 51
Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe
Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe INFORMATION The Stargrip Mechanical Joint Restraint System is a unique product with a proven design that provides an exceptional
More informationJoint Restraints/ Bell & Spigot Joint/ New & In-Service Installations (2" IPS PVC Pipe)
C 1 C 1.1 Joint Restraints/ Bell & Spigot Joint/ New & In-Service Installations (2" IPS PVC Pipe) Joint Restraints/ Bell & Spigot Joint/ New & In-Service Installations (AWWA C-900 PVC Pipe) C 1.1.1 Joint
More informationSection COUPLINGS AND COUPLING ADAPTERS. This Section covers couplings and coupling adapters for ductile iron and steel pipe.
PART 1 GENERAL 1.01 SUMMARY Section 15155 This Section covers couplings and coupling adapters for ductile iron and steel pipe. 1.02 MEASUREMENT AND PAYMENT A. No separate payment for Work performed under
More informationONE-LOK Series SLC/SLCE Pipe Restraint for AWWA C909 PVC Pipe
ONE-LOK Series SLC/SLCE Restraint for AWWA Use the SIGMA ONE-LOK Series SLC/SLCE restraint for AWWA pipe at mechanical or push-on joint ductile iron fittings. The ONE-LOK Restraint Systems can successfully
More informationPipe Restrainers series C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings
Pipe Restrainers series 1000 1000C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings INFORMATION Restrainers for restraining mechanical joint or push-on fittings
More informationPipe Restraints and Adapter Flanges. Section U. For PVC, Ductile Iron and Steel Pipe. 09/2017 Web Revision
DQS Inc. THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Section U 09/2017 Web Revision 11-29-17 Restraints and Adapter Flanges For PVC, Ductile Iron and Steel Contents Applications
More informationAMERICAN Ductile Iron Flex-Ring Joint Pipe Centrifugally Cast for Water, Sewage, or Other Liquids
AMERICAN Ductile Iron Flex-Ring Joint Pipe Centrifugally Cast for Water, Sewage, or Other Liquids 4-12 Flex-Ring Joint 14-54 Flex-Ring Joint AMERICAN Flex-Ring Restrained Joint Ductile Iron pipe, utilizing
More informationFIELD LOK 350 Gasket 4" 24"
FIELD LOK 350 Gasket JOINT RESTRAINT FOR WATER & WASTEWATER, FIRE PROTECTION & INDUSTRIAL APPLICATIONS NSF P 2 Table of Contents FIELD LOK 350 Gasket 3 Assembly 4 Alternative Assembly Methods 7 Pipe Diameters
More informationFIELD LOK 350. Gasket 4" 24" JOINT RESTRAINT NSF FOR WATER & WASTEWATER, FIRE PROTECTION & INDUSTRIAL APPLICATIONS. Certified to ANSI/NSF 61
4" 24" FIELD LOK 350 JOINT RESTRAINT Gasket FOR WATER & WASTEWATER, FIRE ROTECTION & INDUSTRIAL ALICATIONS 4" 24" FIELD LOK 350 Gasket 2 Table of Contents FIELD LOK 350 Gasket 3 Assembly 4 Alternative
More informationDUCTILE IRON PIPE JOINTS AND THEIR USES
DUCTILE IRON PIPE JOINTS AND THEIR USES Ductile Iron Pipe Joints and Their Uses By Richard W. Bonds, P.E. DIPRA Research and Technical Director Introduction Joints for Iron pipe have come a long way. About
More informationFOR WATER & WASTEWATER, FIRE PROTECTION & INDUSTRIAL APPLICATIONS
JOINT RESTRAINT (4" - 24") Gasket FOR WATER & WASTEWATER, FIRE ROTECTION & INDUSTRIAL ALICATIONS 866.DI.IE 2 Table of Contents Gasket 3 Assembly 4 Alternative Assembly Methods 7 ipe Diameters 8 Assembly
More informationSection 9 AMERICAN. Restrained Joint Pipe
Section 9 AMERICAN Restrained Joint Pipe AMERICAN Restrained Joint Pipe The principal standards relating to applicable features of AMERICAN Restrained Joint Pipe and Fittings are ANSI/AWWA C151/A21.51,
More informationThe Redi-Flange Method. How It Works. Services. Engineering & Costing Assistance
... g n ldi ng... e i W No hread ing! T oov o N Gr o N The Redi-Flange Method Redi-Flange is a method of joining valves, fi ttings and equipment with integral fl anged ends to plain-ended pipe, with all
More informationGENERAL PROVISIONS OF THE SPECIFICATIONS MATERIAL SPECIFICATIONS LIST
GENERAL PROVISIONS OF THE SPECIFICATIONS MATERIAL SPECIFICATIONS LIST 1a. PIPE (PVCO): P.W. Eagle 200 PSI in accordance with AWWA C909. Use class 200 unless otherwise approved. Water Pipe Main Diameter
More informationMANHOLES PART I: GENERAL. A. Precast Concrete Manholes
MANHOLES PART I: GENERAL A. Precast Concrete Manholes 1) Manholes shall be made of precast concrete sections of which the top section shall be eccentric or flat slab top. The bottom section shall be a
More informationSPECIFICATION STEEL COUPLING MODEL 411
Sleeve Bolt Nut Follower Gasket 1/2 2 TWO BOLT 3 12 HIGH STRENGTH 2 12 SMALL O.D. 14 60 LARGE O.D. APPLICATIONS Typical Uses Joining plain-end pipe of same outside diameters Replace split or excessively
More informationAF-4 Grooved Flange Adapter
SUBMITTAL INFORMATION PROJECT NAME: ENGINEER: CONTRACTOR: SPEC. SECTION: MEMBER FEATURES & ADVANTAGES Designed for connecting ANSI/AWWA C110/A21.10 and ASME/ANSI B16.1 Class 125/ flanged end components
More informationSECTION 2. AMERICAN Pipe Joints
SECTION 2 AMERICAN Pipe Joints The AMERICAN Fastite Joint is a pushon type joint meeting all the rigorous requirements of AWWA C111. The ANSI/AWWA C600 Standard covers in detail the installation of ductile
More informationSAUSALITO-MARIN CITY SANITARY DISTRICT MISCELLANEOUS UPGRADES PROJECT. Addendum No. 2
SAUSALITO-MARIN CITY SANITARY DISTRICT MISCELLANEOUS UPGRADES PROJECT Addendum No. 2 The following shall modify the Contract Documents. The work shall be accomplished in accordance with such modifications.
More informationGeneral Information...SA1-SA4
SECTION S INDEX Product Description Page Number General Information................................................................SA1-SA4 Type FSK Thruwall & Floor Seal For Conduit, Pipe or Tubing............................
More informationThru Wall Floor Seals For New Installation
The O-Z/Gedney Thruwall and Floor Seals provide a positive means of sealing pipe, conduit or tube where they pass through a concrete foundation of a structure below grade or below ground water level or
More informationSection 2. AMERICAN Pipe Joints
Section 2 AMERICAN Pipe Joints AMERICAN Joints for Pipe and Fittings AMERICAN Fastite Joint, 4-64 The AMERICAN Fastite Joint, furnished in sizes 4-64, is a flexible, rubber ring compression-type joint
More informationTerraBrute CR (4-12 ) Pipe Installation Guide
1.0 Introduction TerraBrute CR is an integral-bell restrained-joint PVC pipe that meets the performance requirements of AWWA C900 (1). It has a slight modification that allows the joints to be locked for
More information9. Construction Activities
9. Construction Activities DIABLO WATER DISTRICT STANDARD SPECIFICATIONS AND DRAWINGS CONSTRUCTION ACTIVITIES I. Construction Sequence and Requirements II. Construction Submittal Checklist DIABLO WATER
More informationThis specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface.
SPEC-3500 1/9 1.0 PURPOSE This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface. Note: This specification does
More informationSECTION BASIC MATERIALS AND METHODS
SECTION 15050 BASIC MATERIALS AND METHODS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe and Fittings. 1.02 RELATED SECTIONS A. Basic Mechanical Requirements: Section 15010. B. Supports, Anchors, and Seals:
More informationMATERIAL COMBINATION NUMBER 2: Corrosive environment requiring harder, wear-resistant seating faces and resistance to dezincification.
Cast Iron Slide Gates Spec Sheet General The contractor shall furnish and install the following cast iron slide gate assemblies as listed on the Gate Schedule and detailed on the manufacturer s drawings.
More informationSECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationS W E RV E RAC K. Simple Security. Simple Stability.
S W E RV E RAC K Simple Security. Simple Stability. The Swerve Rack is a proven design that provides high security and easy bike parking. The Swerve Rack uses thick pipe construction and the full radius
More informationThe MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. Hand or power. kpa/34.
MUELLER SMALL DRILLING MACHINES 2.1 Shaded area indicates change Rev. 9-09 MUELLER Co. manufactures several different small drilling machines for drilling holes from 7/16" to 2" in all types of pipe. Machines
More information.1 Materials and installation for steel piping, valves and fittings for hydronic systems in building services piping..2 Related Sections.
Issued 2006/08/01 Section 15183 Hydronic Systems: Steel Page 1 of 6 PART 1 GENERAL 1.1 SUMMARY.1 Section Includes..1 Materials and installation for steel piping, valves and fittings for hydronic systems
More informationEssex County College - West Essex Campus Addition And Renovations dlb # / SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART I - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationFigure 11 Flange Adapter and Back-Up Ring
Flange Adapters Standard back-up rings are Standard back-up rings are convoluted ductile iron with AWWA C207 150 lb drilling. One edge of the back-up ring bore must be radiused or chamfered. This edge
More informationSECTION MANHOLES
SECTION 02601 MANHOLES PART 1 GENERAL 1.01 SCOPE OF WORK A. WORK required under this section consists of all materials, accessories, equipment, tools, and labor required to install precast concrete standard
More informationThe MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. The main is drilled out under pressure.
MUELLER SMALL DRILLING MACHINES 2.1 Rev. 9-09 MUELLER Co. manufactures several different small drilling machines for drilling holes from 7/16" to 2" in all types of pipe. Machines are available in hand
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationREPAIR CLAMP PARTS H fax: MULTIPLIER
REPAIR CLAMP PARTS Part Number Component Description Model Number Product Size List Price Unit V001 Neoprene Sheet Gasket AS All Sizes Square Inch V002 Waffle Pattern Gasket (NBR) AS All Sizes Square Inch
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationUL / FM E-1 FIRE PROTECTION PRODUCTS INDICATOR POST FEATURES. *Applies to "ORDER LENGTH" codes B through F; code A has 22" adjustment.
UL / FM MUELLER Indicator Post are used in fire protection systems and perform several functions. The Indicator Post provides a means to operate a buried or otherwise inaccessible valve. Also, the Indicator
More informationThe Manitoba Water Services Board SECTION Standard Construction Specifications September 2013 Page 1 of 8
September 2013 Page 1 of 8 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work described herein shall consist of the construction of air release chambers, flushout chambers, valve chambers, meter chambers
More informationAppendix C Construction Details
7172 Kennedy Road Warrenton, Virginia 20187 Appendix C Construction Details November 2017 TABLE OF CONTENTS THRUST BLOCKS Anchorage for 11 1/4 o, 22 1/2 o & 45 o Upper Vertical Bends... AV 01 Buttresses
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationDrilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2
TOOLS Page Q 2 Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2 Page Q 3 Changeable carbide drill (WHM) Page Q 3/1 Drilling machine Tonisco
More informationADDENDUM NO. 1 TO THE CONTRACT DOCUMENTS AND SPECIFICATIONS DATED JULY 2017 FLORIDA GOVERNMENTAL UTILITY AUTHORITY PROJECT NO.
ADDENDUM NO. 1 TO THE CONTRACT DOCUMENTS AND SPECIFICATIONS DATED JULY 2017 FLORIDA GOVERNMENTAL UTILITY AUTHORITY PROJECT NO. PS 061 SEVEN SPRINGS WASTEWATER TREATMENT FACILITY IMPROVEMENTS PASCO COUNTY,
More informationGeberit Duofix. Installation Manual Montageanleitung Instructions de montage Istruzioni per il montaggio
Geberit Duofix Installation Manual Montageanleitung Instructions de montage Istruzioni per il montaggio Masse Geberit Duofix Element für Wand-WC, cm, mit Sigma Unterputzspülkasten cm 9¾" (500) 4¾" (0)
More informationRELINER INSIDE DROP SYSTEM SPECIFICATIONS
1. PRODUCT NAME RELINER INSIDE DROP SYSTEM U.S. Patent 6074130 Canadian Patent # 2269565 All RELINER Products are proudly made in the U.S.A. 2. MANUFACTURER RELINER /Duran Inc. 53 Mount Archer Rd. Lyme
More informationD. Thermally Sprayed Metallic Coating (Flame Spray): STD SPEC
STANDARD SPECIFICATION SECTION 05121 MISCELLANEOUS METALWORK PART 1 - GENERAL 1.01 DESCRIPTION This section includes materials, fabrication, and installation of structural steel, connecting bolts, pipes,
More information3.1 MUELLER LARGE DRILLING MACHINES
MUELLER LARGE DRILLING MACHINES 3.1 Shaded area indicates change Rev. 1-09 Large Drilling Machines are used for making 2" to 24" lateral connections on water mains under pressure. These machines are available
More information3.1 MUELLER LARGE DRILLING MACHINES
MUELLER LARGE DRILLING MACHINES 3.1 Shaded area indicates change Rev. 1-09 Large Drilling Machines are used for making 2" to 24" lateral connections on water mains under pressure. These machines are available
More informationCSS Central Mount System
CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3004 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Water Design Conditions Operating Conditions 10 PSIG @ 33 o F to
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationCIC 200 PLASTIC SCREW ANCHOR ASSORTMENT WITH PHILLIPS BINDING HEAD METAL SCREWS. 6 x 3/4 P/N x 1 METAL SCREW P/N x 3/4 METAL SCREW
A21-1 1160 CIC 200 PLASTIC SCREW ANCHOR ASSORTMENT WITH PHILLIPS BINDING HEAD S For light duty applications in solid materials Color coded diameters for easy identifi cation Acid resistant NYLON FLANGED:
More informationSIGHT GLASS. Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels.
SIGHT GLASS Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels. SIGHT GLASS Sight flow indicator. A sight flow indicator is used in process pipelines
More informationAssembly Instructions for Key-Lock mechanical joints in sizes 2 to 40 inch ( mm)
Assembly Instructions for Key-Lock mechanical joints in sizes 2 to 40 inch (50-1000 mm) Introduction This guide provides recommendations for the installation of Bondstrand piping systems using the Key-Lock
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationHUSSEY GAY BELL SAVANNAH, GEORGIA
HUSSEY GAY BELL SAVANNAH, GEORGIA ------------------------------------------------------------------------------------------------------------ ADDENDUM NO. 3 TO THE CONTRACT DOCUMENTS AND TECHNICAL SPECIFICATIONS
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationTuf-Lite III Fans 5000K Series Hub
Tuf-Lite III Fans 5000K Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 20 thru 30 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced
More informationPVC PRESSURE PIPE TAPPING GUIDE
PVC PRESSURE PIPE TAPPING GUIDE TABLE OF CONTENTS FOREWORD 03 INTRODUCTION 04 DIRECT TAPPING 09 SADDLE TAPPING 17 SLEEVE TAPPING 24 MEMBERS 29 2 UNI-BELL PVC PIPE ASSOCIATION WWW.UNI-BELL.ORG FOREWORD
More informationTuf-Lite III Fans 5000K Series Hub
Tuf-Lite III Fans 5000K Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 20 thru 30 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced
More informationSYGEF Standard SYGEF Plus PVDF Flanges
Installation Instructions 2009 Volume, Rev 02 PM451 SYGEF Standard SYGEF Plus PVDF Flanges Please read all instructions before attempting to install flanges. Introduction When to Use a Flange Flanges may
More informationEvaluation of In-Pavement Light Fixture Designs and Performance
Evaluation of In-Pavement Light Fixture Designs and Performance Presented to: IES ALC Fall Technology Meeting By: Joseph Breen Date: Background In-Pavement Light Fixture Assemblies Utilize a Circle of
More informationFIRE PROTECTION PRODUCTS
FEATURES Rev. 7-11 Mueller Indicator Post are used in fire protection systems and perform several functions. The Indicator Post provides a means to operate a buried or otherwise inaccessible valve. Also,
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationMEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C
MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C Revised October 2007 Armtec reserves the right to alter designs. General The Armtec Sluice Gate is a quality and highly economical gate for a variety of
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationMax. Rec. Load. Wt. Per Inch lbs. kn lbs. kn lbs. kg. Wt. Per Inch lbs. kn lbs. kn lbs. kg 750 F (399 C)
FIG. 10 FIG. 15 & 15L Function: Designed for use in pipe hanger assemblies. (Type 304 or 316 Stainless Steel upon request) Ordering: Specify figure number, rod size, length (), material, and finish. 650
More informationSprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E".
Product Name Nordic Flow FM Thin Wall Pipes Application Sprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E". Manufacturing Standard
More informationUtility Structures. Utility vaults, trenches, transformer pads Electrical Pole Bases and switching cubicles
Utility Structures Utility vaults, trenches, transformer pads Electrical Pole Bases and switching cubicles PRODUCT GUIDE & TECHNICAL REFERENCE MANUAL Providing the right solutions. UTILITY STRUCTURES Perfect
More informationA. Compatibility: Products shall be suitable for piping service fluids, materials, working pressures, and temperatures.
SECTION 22 05 16 LOOPS FOR PLUMBING PIPING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationFord Water Meter Couplings & Accessories
Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationRodney Hunt. A GA Industries Company Glydaseal Gates
Rodney Hunt A GA Industries Company Glydaseal Gates GUIDE BRONZE GUIDE BAR FRAME NUT POCKET SEAT FACING RESILIENT INVERT SEAT DISC GUIDE BAR ADJUSTMENT BOLT WITH LOCK NUT GUIDE BAR ATTACHING BOLT The Glydaseal
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationHOOP RACK HEAVY DUTY Setbacks WALL 36" WALL 42" 36" STREET 59" STREET Dero
Setbacks WALL 36" WALL 42" STREET 36" 59" STREET Installation Instructions Tape Measure Marker or Pencil Masonry Drill Bit Drill (Hammer drill recommended) Hammer Wrench 9/16 Level RECOMMENDED BASE MATERIAL
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/01/13 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Air Design Conditions Operating Conditions Blast Air (see Note 1)
More informationTuf-Lite III Fans 3000K Series Hub
Tuf-Lite III Fans 3000K Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 11 thru 15 Diameter Hudson Tuf-Lite III fan blades Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced
More information5.1 MUELLER CORPORATION VALVES. MUELLER 300 Ball Type Corporation Valves
MUELLER CORPORATION VALVES 5.1 Shaded area indicates changes Rev. 4-14 Machine inserted corporation stops were developed by Hieronymus Mueller in conjunction with his development of the drilling and tapping
More informationTuf-Lite II Fans 3000H Series Hub
Tuf-Lite II Fans 3000H Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 5 through 14 Diameter Hudson Tuf-Lite II Fan Blades Hudson Tuf-Lite II (white, prev. Blue**) are made from fiberglass
More informationAssembly instruction. for push-in joint pipe DN mm with internal restrained joint Fig. 2807A / 2807B
Assembly instruction for push-in joint pipe DN 80-500 mm with internal restrained joint Fig. 2807A / 2807B 1. General remarks Following the instructions below will guarantee correct and professional assembly.
More informationAssmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS
Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS General Information Assmann polyethylene storage tanks are manufactured to give you the toughest, most reliable
More informationINSTALLATION INSTRUCTIONS. March 2016 FOR FURTHER QUESTIONS, PLEASE CALL
March 2016 INSTALLATION INSTRUCTIONS FOR FURTHER QUESTIONS, PLEASE CALL 775 440 2025 JENSEN WATER RESOURCES 521 Dunn Circle, Sparks, NV 89431 JensenPumps.com Figure 1: This illustration shows a complete
More informationTuf-Lite and Tuf-Lite II Fans 4000 Series Hub
Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub INSTALLATION MANUAL Hudson Tuf-Lite and Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 15 thru 20 Diameter Hudson Tuf-Lite (black) fan blades are made
More informationTuf-Lite II Fans 3000H Series Hub
Tuf-Lite II Fans 3000H Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 5 through 14 Diameter Hudson Tuf-Lite II Fan Blades Hudson Tuf-Lite II (white, prev. blue**) fan blades are made from
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationTuf-Lite II Fans 3000HC Series Hub
Tuf-Lite II Fans 3000HC Series Hub INSTALLATION MANUAL Hudson Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 8 through 10 Diameter Hudson Tuf-Lite II (White) are made from fiberglass reinforced vinyl-ester
More informationAmerican Safe Room. Explosion Resistant Blast Hatch with Integrated Riser
American Safe Room Explosion Resistant Blast Hatch with Integrated Riser Drawing: ASR-50-RBH Revision: H May 17, 2012 Table of Contents Description... 3 Options... 4 Order form... 5 Option: left or right
More informationTuf-Lite and Tuf-Lite II Fans 4000 Series Hub
Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub INSTALLATION MANUAL Hudson Tuf-Lite and Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 15 thru 20 Diameter Hudson Tuf-Lite (black) fan blades are made
More informationANSI ORIFICE FLANGES METAL-KOREA
METAL-KOREA ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding
More informationUPDATE LOG FOR STANDARD DRAWINGS Item(s) Changed 6/1/18 STANDARD DRAWINGS
Date 6/1/18 STANDARD DRAWINGS UPDATE LOG FOR STANDARD DRAWINGS Item(s) Changed WATER STANDARD DRAWINGS Title Drawing Number Current Date Fire Hydrant and Appurtenance Locations, Improved Streets with Curb
More informationTYPHOON ASSEMBLY AND INSTALLATION INSTRUCTIONS
TYPHOON ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503) 266-4334
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.
Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationTuf-Lite III Fans K Hi Temp 3000KHT Series Hub
Tuf-Lite III Fans K Hi Temp 3000KHT Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 11 thru 15 Diameter Hudson Tuf-Lite III fan blades Hudson Tuf-Lite III Hi Temp (Red) fan blades are of single
More informationTHE AquaBlast & RocketRide FUNSLIDES
THE AquaBlast & RocketRide FUNSLIDES ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * S.R. SMITH AquaBlast TM & RocketRide TM FUNSLIDES TM ARE MANUFACTURED FOR INSTALLATION AND USE ON RESIDENTIAL
More informationSECTION PRECAST CONCRETE SECTIONAL MANHOLES
SECTION 02545 PRECAST CONCRETE SECTIONAL MANHOLES PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: 1. Precast reinforced concrete cylindrical sectional manholes, complete with openings, inserts, hardware,
More information