13243 INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0 MAKE: LAND ROVER MODEL: RANGE ROVER SPORT STYLE: SUV WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY For more information log onto & for helpful towing tips log onto WEIGHT CARRYING: TRAILER WEIGHT: TONGUE WEIGHT: 8, LBS. LBS. WARNING: WE RECOMMEND THE USE OF 800 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT FOR FURTHER INFORMATION. PRO INSTALL TIME: NOVICE INSTALL TIME: INSTALLATION REQUIRES: MIN. 90 MIN. IF YOU ARE HESITANT TO UNDERTAKE THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED CURT INSTALLER FOR ADDITIONAL ASSISTANCE. 0mm /6 INSTALLATION TIPS:. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY.. TO EASE INSTALLATION, PEOPLE MAY BE REQUIRED.. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED.. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT LEVEL OF DIFFICULTY: MODERATE VEHICLE PHOTO: SAFETY GLASSES SOCKET TORQUE WRENCH EASY MODERATE CHALLENGING NO DRILLING REPRESENTATIVE PHOTO SCREW DRIVER ROTARY TOOL BOXED END WRENCH /6 TRIMMING REQUIRED HITCH ILLUSTRATION: RATCHET SCAN FOR MORE INFO MAKE SURE YOUR HITCH MATCHES PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V- and SAE J68. 7/8/0

2 INSTALLATION WALKTHROUGH: Parts List ITEM QTY PART NUMBER DESCRIPTION M-.7 x 0mm HEX BOLT /" CONICAL TOOTHED WASHER /8- x HEX BOLT. Remove upper panel cover secured by () quarter turn fasteners. Remove lower panel cover by removing the () screws using a 0mm socket and phillips screwdriver. Save for reinstallation in Step. 9/6 WASHER FLAT WASHER /8- HEX FLANGE NUT VEHICLE CROSS SUPPORT EXISTING WELDNUTS (BOTH SIDES) REAR BUMPER BEAM. Raise hitch over exhaust and into position and loosely secure hitch with () M bolts and conical washers. Slide flat washers into position then /8" bolt through washer, bumper beam, and hitch securing with hex flange nut.

3 INSTALLATION WALKTHROUGH:. Torque M bolts to 79 ft-lbs, and /8" bolt to 80 ft-lbs.. Reinstall upper and lower panel covers removed in Step.. Trim lower panel cover using diagrams below for reference. USE CONTOUR AS GUIDE USE CONTOUR AS GUIDE.0 in 6.0 in.0 in.00 in

4

5 7/8/0 LAND ROVER RANGE ROVER SPORT GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 8,000 LBS. TRAILER WEIGHT & 800 LBS. TONGUE WEIGHT. WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 800 STABILIZING STRAPS. WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY ** WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY *** FOR MORE INFORMATION LOG ONTO & FOR HELPFUL TOWING TIPS LOG ONTO HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT Parts List ITEM QTY PART NUMBER DESCRIPTION M-.7 x 0mm HEX BOLT /" /8- x 9/6 WASHER /8-.0 in CONICAL TOOTHED WASHER HEX BOLT FLAT WASHER HEX FLANGE NUT USE CONTOURS AS GUIDES VEHICLE CROSS SUPPORT.00 in EXISTING WELDNUTS (BOTH SIDES) 6.0 in.0 in REAR BUMPER BEAM TOOLS REQUIRED SAFETY GLASSES 0mm & /6 SOCKETS /6 WRENCH RATCHET FLAT & PHILLIPS SCREW DRIVER TORQUE WRENCH ROTARY TOOL HITCH WEIGHT: LBS. INSTALL TIME PROFESSIONAL: MINUTES NOVICE (DIY): 90 MINUTES INSTALL NOTES: - No drilling - Fascia trimming required INSTALLATION STEPS. Remove upper panel cover secured by () quarter turn fasteners. Remove lower panel cover by removing the () screws using a 0mm socket and phillips screwdriver. Save for reinstallation in Step.. Raise hitch over exhaust and into position and loosely secure hitch with () M bolts and conical washers. Slide flat washer into position then /8" bolt through washer, bumper beam, and hitch securing with hex flange nut.. Torque M bolts to 79 ft-lbs, and /8" bolt to 80 ft-lbs.. Trim lower panel cover using diagram above for reference.. Reinstall upper and lower panel covers removed in Step. PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND. CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. Scan If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, for more with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to information repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V- and SAE J68.