Sydney Opera House (Australia): Assembly Instructions

Size: px

Start display at page:

Download "Sydney Opera House (Australia): Assembly Instructions"

Nigel Allison
6 years ago
Views:

http://www.canon.com/c-park/en/ Before starting assembly:writing the number of each section on its back side before cutting out the sections is highly recommended.

1 Before starting assembly:writing the number of each section on its back side before cutting out the sections is highly recommended. (* This way, you can be sure which section is which even after cutting out the sections.) Indicates where sections should be glued together. (1) Build the base. 2 1 View of completed model *This model was designed for Papercraft and may differ from the original in some respects. Assembly Instructions: Six A4 sheets (No.1 to No.6) *Build the model by carefully reading the Assembly Instructions, in the parts sheet page order. 4 *Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold. 6 8 Assembly Instructions Mountain fold(dotted line) Make a mountain fold. Valley fold(dashed and dotted line) Make a valley fold. Glue The glue spot(colored dot) shows where to apply the glue. Glue spot(red dot) Glue parts with the same number together. 5 Sydney Opera House Sydney, Australia Scissors line(solid line) Cut along the line. Cut in line(solid line) Cut along the line. Glue spot(green dot) Glue within the same part. Glue spot(blue dot) Glue to the rear of the other part. Insert. 7 3 Tools and materials Assembly tip Caution Scissors, set square, glue(we recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children. 1

2 (2) Build the fan-shaped foundation

3 (3) Build the lower level of the structure. 25 Insert between the folded sides. 21 Insert between the folded sides. 24 Fold each of parts 21, 22, 24, and 25 before gluing them to part 17. * Since folding these parts after gluing them to part 17 may cause the paper on the exterior to stick out or tear, be sure to glue these parts in place after folding them. Match the borders of the coloring when gluing these pieces together. Insert between the folded sides Match the borders of the coloring when gluing these pieces together When assembling this section, first attach parts 21, 22, 24, and 25 to part 17, then connect the parts together by adjusting the location of the connection between each part. Insert between the folded sides. 3

4 41 Glue along the dotted line Large hall Glue in the same way as part 29. (4) Build the large and small halls and the restaurant. Assemble parts 33, 35, 38, 45, 52, 55, and 56 in the same general way Glue together Glue in the same way as on the opposite side Glue one side to part 38 and one side to part 32. Assemble parts 30, 32, 34, 39, 44, 50, 53, 54, 57, and 59 in the same general way. Glue parts 28, 29, 40, and 41 in place last, adjusting the assembled parts while doing so. 4

5 42 44 Small hall Glue in the same way as part Glue one side to the rear side of part 44 and one side to part Restaurant Glue parts 46, 47, 48, 49, and 61 in place last, after assembling all these parts together, adjusting the assembled parts while doing so. (5) Glue the large and small halls and the restaurant to (3) the lower section of the structure (3). Large hall Small hall Restaurant (3) Lower section of structure 5

6 (6) Complete the model by gluing the base assembled in step (1) to the foundation assembled in step (2) and the structure assembled in step (5). (5) Structure (2) Foundation (1) Base Finished! 6

Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C

Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C http://www.canon.com/c-park/en/ Before starting assembly:writing the number of each section on its back side before cutting out the sections is highly recommended. (* This way, you can be sure which section