Compliance Certification Services Inc. Report No: MIL(CE101) Date of Issue: August 25, 2009 MIL STD 461E/ F TEST REPORT.

Transcription

1 Hccs MIL STD 461E/ F TEST REPORT For 20.1 Multimedia LCD Monitor Model Number: WMRM920-PIP Trade Name: itech Issued to itech Company LLC Christy Street, Fremont CA USA Issued by No. 11, Wugong 6 th Rd., Wugu Industrial Park Taipei Hsien 248, Taiwan service@tw.ccsemc.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 18 Rev. 00

2 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION 3 2. EUT DESCRIPTION 4 3. TEST METHODOLOGY 5 4. INSTRUMENT AND CALIBRATION MEASURING INSTRUMENT CALIBRATION MEASUREMENT EQUIPMENT USED 5 5. FACILITIES AND ACCREDITATIONS FACILITIES 6 6. SETUP OF EQUIPMENT UNDER TEST SETUP CONFIGURATION OF EUT PHOTOGRAPHS OF EUT SUPPORT EQUIPMENT TEST SETUP 7 7. MIL STD 461E/ F REQUIREMENTS CE101, CONDUCTED EMISSIONS, POWER LEADS, 30 HZ TO 10 KHZ 8 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP 18 Page 2 Rev. 00

3 xcs Report No: MIL(CE101) Dale of Issue: August 25, TEST RESULT CERTIFICATION Applicant: Equipment Under Test: Trade Name: Model Number: itech Company LLC Christy Street, Fremont CA USA 20.1 Multimedia LCD Monitor itech WMRM920-PIP Date of Test: August 24, 2009 STANDARD MILSTD461E/F APPLICABLE STANDARDS TEST RESULT No non-compliance noted ' Applicable Standard MIL STD 461E/F CE101, conducted emissions, power leads, 30 Hz to 10 khz. Deviation from Applicable Standard Test Result No non-compliance noted N/A The above equipment was tested by for compliance with the requirements set forth in MIL STD 46 IE/ F. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Note: During the test, Dell PC and VGA cable are sealed by copper foil tape. Approved by: Reviewed by: )->ua James Lee Section Manager 9 1st d CK L^tlAlA Bruce Chen Senior Engineer Page 3 Rev. 00

4 2. EUT DESCRIPTION Product Trade Name Model Number 20.1 Multimedia LCD Monitor itech WMRM920-PIP Model Discrepancy MB: itech/ R2A EUT Power Panel LCD: 20.1 AUO / M201UN02-V6 Rating Power Board: Wearnes/ WDS RS232 Port: Link PC /Touch Remark: for more details, please refer to the User's manual of the EUT. Page 4 Rev. 00

5 3. TEST METHODOLOGY All tests were performed in accordance with the procedure documented in MIL STD 461E/ F. 4. INSTRUMENT AND CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer s recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement CE101 (966 Chamber B) Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A MY /25/2010 Coaxial Cable Huber Suhner SUCOFLEX /01/2010 LISN R&S AT/A /27/2009 RF Current Probe FCC F /10/2010 Site NSA CCS N/A N/A 01/02/2010 Software Turbo C++ Page 5 Rev. 00

6 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.199, Chunghsen Road, Hsintien City, Taipei Hsien, Taiwan, R.O.C. Tel: / Fax: G No.11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan Tel: / Fax: G No.81-1, Lane 210, Bade 2nd Rd., Luchu Hsiang, Taoyuan Hsien 338, Taiwan Tel: / Fax: The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. Page 6 Rev. 00

7 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 PHOTOGRAPHS OF EUT See test photographs attached in Appendix 2 for the EUT s internal structure. 6.3 SUPPORT EQUIPMENT No. Device Ty pe Brand Model Series No. FCC ID Data Cable Power Cord 1 Notebook PC DELL PP19L GH645 A03 E2KWM3945ABG N/A N/A Remarks: 1. All the above equipment/cables were placed in worse case positions to maximize emission signals during emission test. 2. Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use. 6.4 TEST SETUP The equipment under test was configured in normal operation continuously. EUT tends to maximize its emission characteristics in a typical application for conducted emission measurement. The EUT was active during the conducted emission measurements. Page 7 Rev. 00

8 ccs 7. MIL STD 461E/ F REQUIREMENTS 7.1 CE101, conducted emissions, power leads, 30 Hz to 10 khz This requirement is applicable for power leads, including returns, that obtain power from other sources not part of the EUT for surface ships, submarines, Army aircraft& (including flight line) and Navy aircraft *& *For equipment intended to be installed on Navy aircraft, this requirement is applicable only for aircraft with Anti-Submarine Warfare (ASW) capability. & For AC applications, this requirement is applicable starting at the second harmonic of the EUT power frequency. Conducted emissions on power leads shall not exceed the applicable values shown on Figures CE101-1 through CE101-3, as appropriate, for submarines and Figure CE101-4 for Army aircraft (including flight line) and Navy ASW aircraft. LIMIT FIGURE CE CE101 limit for submarine applications, DC. Page 8 Rev. 00

9 ccs FIGURE CE CE101 limit for submarine applications, 60Hz. Page 9 Rev. 00

10 ccs FIGURE CE CE101 limit for submarine applications, 400 Hz. Page 10 Rev. 00

11 ffc I \\^*\ 10D 1k Frequency (Hz) FIGURE CE CE101 limit for Navy ASW aircraft and Army aircraft (including flight line) applications. Page 11 Rev. 00

12 ffc I \\^*\ TEST CONFIGURATION FIGURE CE Measurement setup. TEST PROCEDURE The magnetic emission of EUT representative of its type shall be tested by the method(s) according to MIL STD 461E/ F. Page 12 Rev. 00

13 ccs TEST RESULTS No non-compliance noted Test Data 30Hz-lkHz-Ll Job No.: Polarization: N Standard: MIL-STD-461E/F CE101 Navy &army(above 28V) Power Source: AC 120V/60Hz Test item: Conduction Test Date: 2009/8/24 Temp.( C)/Hum.(%): 22( C)/51% Time: ±^f 11:24:20 Company: itech Company LLC Engineer Signature: Trade Name: itech Distance: 5cm Chris Model: WMRM920-PIP RBW: 0.01 khz VBW: 0.01 khz Description: Dell PC+ VGA cable are sealed by copper foil tape dkiia Limit: khz No. Frequency Reading Factor Result Limit Margin Detector P/F Remark (KHz) (dbua) (db) (dbua) (dbua) (db) peak -- Main wave peak P peak P peak P Page 13 Rev. 00

14 peak P peak P peak P peak P Note: For AC applications, this requirement is applicable starting at the second harmonic of the EUT power frequency. Page 14 Rev. 00

15 ccs Report No: MIL(CE101) Date of Issue: August 25,2009 lkhz-lokhz-ll Job No.: Polarization: N Standard: MIL-STD-461E/FCE101 Power Source: AC 120V/60Hz Navy &army(above 28V) Test item: Conduction Test Date: 2009/8/24 Temp.( C)/Hum.(%): 22( C)/51% Time: ±^f 11:29:25 Company: itech Company LLC Engineer Chris Signature: Trade Name: itech Distance: 5cm Model: WMRM920-PIP RBW: 0.1 khz VBW: 0.1kHz Description: Dell PC+ VGA cable are sealed by copper foil tape dbua Limit: ^r 1 1 f \ * 50 V \-~S \ ' L H^j W-J\M/W v l^vv \ GO Of khz No. Frequency Reading Factor Result Limit Margin Detector P/F Remark (KHz) (dbua) (db) (dbua) (dbua) (db) peak P peak P peak P peak P peak P peak P Paae 15 Rev. 00

16 ccs 30Hz-lkHz-L2 Job No.: Standard: Test item: Temp.( C)/Hum.(%): Company: MIL-STD-461E/F CE101 Navy &army(above 28V) Conduction Test 22( C)/51% itech Company LLC Polarization: Power Source: Date: Time: Engineer N AC 120V/60Hz 2009/8/24 _h^p 11:35:33 Chris Signature: Trade Name: Model: itech WMRM920-PIP Distance: RBW: 0.01kHz 5cm VBW: 0.01 khz Description: Dell PC+ VGA cable are sealed by copper foil tape dbua khz No. Frequency Reading Factor Result Limit Margin Detector P/F Remark (KHz) (dbua) (db) (dbua) (dbua) (db) peak Main wave * peak peak peak ll.i peak peak peak peak Note: For AC applications, this requirement is applicable starting at the second harmonic of the EUT power frequency. Page 16 Rev. 00

17 ccs lkhz-10khz-l2 Job No.: Polarization: N Standard: MIL-STD-461E/F CE101 Power Source: AC 120V/60Hz Navy &army(above 28V) Test item: Conduction Test Date: 2009/8/24 Temp.( C)/Hum (%): 22( C)/51% Time: ±*f 11:33:51 Company: itech Company LLC Engineer Chris Signature: Trade Name: itech Distance: 5cm Model: WMRM920-PD? RBW: 0.1kHz VBW: 0.1kHz Description: Dell PC+ VGA cable are sealed by copper foil tape dbua Limit: khz No. Frequency Reading Factor Result Limit Margin Detector P/F Remark (KHz) (dbua) (db) (dbua) (dbua) (db) peak P peak P peak P peak P peak P Page 17 Rev. 00

18 ffc I \\^*\ 8. APPENDIX I PHOTOGRAPHS OF TEST SETUP CE101, conducted emissions, power leads, 30 Hz to 10 khz ^^^^^W TTT-^^H^^ _» 1 ^ ^ J ^ B ^k ^^BI^^H 1 ^^ ^ ^^^^^^^^^^^^ I 1 J ) 1 j II T] l^kafl^h 9E3 ^f,3j -^ JH K i" ^ ^^ - ^^ ^ ^H ^ v^^h ^^S-. ^B^^l Page 18 Rev. 00