High-sensitivity with vertical hole. PFA 2.6/cm (260/m) C 1.0 MPa or less Approx. 19kg Approx. 10kg (L: 500) Outdoor installation Rainproof type

Transcription

1 High Sensitivity Type Electromagnetic Conductivity Detector ME-6 /7 /T Series These products are conductivity sensors that function based on electromagnetism. Combined with a dedicated converter, they provide accurate measurement of the conductivity of a solution. They can measure highly corrosive or conductive acid or alkaline solutions and seawater, which cannot be measured with electrode type devices. PF or PVC is used as the liquid contact material. There are multiple mounting methods available: pipeinsertion types, immersion types, throw-in types, and flow liquid types. ME-6T ME-7T Features For hydrochloric acid, sulfuric acid, and caustic soda, conductivity and temperature can be measured and converted into concentrations. This means the product can be manufactured as a concentration meter. wide range of measurements is possible. The minimum measurement range (maximum sensitivity) is 5µS/cm (.5 ms/cm). The maximum measurement range is S/cm ( ms/cm). There are two series a high-sensitivity type with diameter of ø (ME-T/6/7 model; cell constant.6/cm) and a small lightweight type with a diameter of ø.5 (ME- model; cell constant 9./cm). Either type can be selected depending on the usage and installation conditions. The devices are installed beneath a drip-proof structure and can be set up outdoors. Representative sensors and basic specifications Model Category Shape / Use Process connection Contact liquid component material Cell constant Working temperature Working pressure Weight Construction ME-6T ME-7T High-sensitivity with vertical hole Flow liquid type Immersion type 5 JIS K RF JIS K RF PF.6/cm (6/m) - C. MPa or less pprox. 9kg pprox. kg (L: 5) Outdoor installation Rainproof type System configuration Detector Transmitter MM-6/6 Field Instrument room Receiver Detector cable 5m Transmission output DC - m DCS Recorder Controller,etc Flow liquid type Immersion type larm contact ( points) output C power supply C - V, 5/6 Hz Power shutdown contact output (optional)

2 Measurement principle The detection component comprises two stacked transformers that are molded or lined with insulators. The component is immersed in a sample liquid to perform conductivity measurement by using the electromagnetic current flowing in the liquid. s shown in the main diagram, two toroidal transformer coils T and T are fitted, forming an equivalent single-coil circuit, C, which is cross-linked with T and T. When an alternating current is sent to primary coil C, then current i, which is relative to the conductivity of the solution, flows to C. On the other hand, voltage e, which is proportional to the current flowing to coil C, is generated in secondary coil C in transformer T, which uses C as its primary coil. This voltage value is proportional to the conductivity of the solution, thus enabling the conductivity of a solution to be determined by measuring voltage e.. Conditions for concentration meters Electromagnetic type concentration meters function based on the principle of conductivity measurement. When the conductivity of solution concentrations is graphed, maximum or minimum points are apparent for most high-concentration inorganic salts. Thus, no concentration meter should be manufactured that includes these points within the measurement range. For example, with HNO, maximum conductivity is at a concentration of around %. nitric acid concentration meter therefore must have a measurement range of, for instance, % 5% or, to exclude maximum points, 5% 6%. If changes in conductivity in response to concentrations of impurities or coexisting components in the sample liquid are negligible in comparison with conductivity changes in response to concentrations of measured components, then it is possible to measure concentrations; however, measurement errors will increase if the former changes are too great to be ignored. Excitation current S/cm Conductivity Principle diagram Lead wire Detection transformer Excitation transformer Insulator Structure of detection component HF NaCl HCl NaOH HNO HSO. Minimum and maximum conductivity measurement ranges () Minimum range (highest sensitivity) - 5µS/cm () Maximum - S/cm 6 8 wt Concentrations in solutions Relations between concentrations in solutions and conductivity (8 C) Electromagnetic conductivity sensor In your request for a quotation or order placement, please specify the following: Measurement item.name of solution:.fluctuation range:.presence / absence and percentage of coexisting elements:.temperature ( C) Maximum: Normal: Minimum: 5.Pressure (MPa) Maximum: Normal: Minimum: Requested specifications.classification : High-sensitivity type Compact lightweight type.mounting : Screw insertion type (screw standards: ) method Flange-insertion type Flow liquid type with case Immersion type with flange (length: ) (flange standards: ) Immersion type for open tank Throw-in immersion type.liquid contact material : Hard PVC heat-resistant 6 C Heat-resistant PVC heat-resistant 7 C PF heat-resistant C PVDF heat-resistant C.Special specifications:

3 Model name manufacturing specifications High-sensitivity flow-liquid model ME-6 T E N T S G N H Shape of detection end Horizontal hole type Vertical hole type Slanting hole type Material used for liquid contact components Fluorine resin (PF) Hard PVC Thermistor structure Internal in the detector end External (PF) External (SUS6) External (glass) With/without case Not Provided Provided. The horizontal hole type is appropriate for measuring horizontal flows of sample water, while the vertical hole type is better for measuring vertical flows (to prevent stain adhesion and to prevent air bubbles from being mixed in sample water). High-sensitivity immersion model ME-7 T E Shape of detection end Horizontal hole type Vertical hole type Slanting hole type Material used for liquid contact components Fluorine resin (PF) Hard PVC High-sensitivity multi-use model (PF) ME-T Screw type IDF flange (ferule) type Throw-in type. Heat-resistant to C with PF, C with PVDF, 65 C with heat-resistant PVC, and 6 C with hard PVC. Withstand voltage varies according to material and shape (structure). Please see the specifications (product code) for each model.. If the sample water temperature is subject to fast and violent changes, the external thermistor type is recommended because it responds more rapidly to temperature fluctuations. Sensor selection based on measuring solutions and measurement conditions Solution Sodium chloride (NaCl) Hydrochloric acid (HCl) Nitric acid (HNO) Caustic soda (NaOH) Sulfuric acid (HSO) Conductivity Measurement range - 5% - % - % - 5% - % - 5% 5 - % - % - % 6-7% - 5% - % - 5% - % - 5% - % - % - 8% 6-8% % -.5mS/cm - 5mS/cm - ms/cm - ms/cm - 5mS/cm - ms/cm - ms/cm - 5mS/cm - S/cm Working temperature: - 6(65) C Pressure: -.MPa Working temperature: 6 - () C Pressure:. -.5(.)MPa ME-6E / 7E ME-6 T / 7 T / T ME-6E / 7E ME-6 T / 7 T / T ME-6E / 7E ME- H ME-6 T / 7 T / T ME-6 T / 7 T / T ME-6E / 7E ME-6 T / 7 T / T ME-6E / 7E ME-6 T / 7 T / T ME-6 T / 7 T / T ME-6E / 7E ME-6 T / 7 T / T Note: For measurement to -.5 ms/cm (5 µs/cm) or less, select a double-electrode type conductivity meter.

4 High-sensitivity flow-liquid type Dimensions Unit : mm ME-6TNH PF, vertical hole type, ( internal thermistor ) Sample inlet ø Sample outlet -ø ± (9) ø5 ø9 9 9 Case ø5 ø9 -ø ME-6TTH PF, vertical hole type, ( external thermistor ) Product code Fluorine resin (PF), vertical hole type, cell constant.6/cm ME6T-- 8 lphabet: Z ME-6T N ME-6T H ME-6TN ME-6TT With/without casing material Not provided FCD/liquid contact surface PF lining provided Standards for case connection (flange) 5 JIS K RF equivalent "NSI 5L RF equivalent No applicable: (without case) Thermistor mounting method Internal detection end type (standard) External type Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM- model Japanese(standard) N/ ± (9) Thermistor 9 Sample inlet ø Sample outlet 9 Case ø5 ø9 -ø ø5 ø9 -ø. For case-free models, inform us of the mounting conditions (whether you are using our proprietary case or your own measurement tank). If you intend to mount this unit on your own measurement tank, you will need an internal diameter of or more to comply with the cell coefficient.. The temperature compensation thermistor is usually built into the detection end (internal type). If the sample water temperature is prone to sharp fluctuations over short periods, select an external type because it responds more rapidly to temperature fluctuations. The withstand voltage of the external thermistor type is. MPa.. The standard cable length (external diameter 8 mm) is 5 m. If you require a cable of more than 5 m in length, select (Specify) and enter the necessary length (up to maximum m).. If a transmitter is indicated as Not provided, inform us of the model name and production number of the transmitter that you are using. Note : The liquid contact material of this sensor is made from PF and its maximum withstand voltage is. MPa. The maximum sample water temperature is C. However, for the external thermistor type, the withstand voltage is. MPa. Note : The detection end of the ME-6T model is a vertical hole type, making it appropriate for measurement of sample water flowing vertically. The detection end is designed to prevent the effect of air bubbles. Even if air bubbles are mixed in sample water, they do not mount to the detection end. The detection end of the ME-6T model is a horizontal hole type, making it appropriate for measurement of sample water flowing horizontally. Thus, when choosing a unit with case, the ME-6T H model or a vertical hole type is recommended because this type of unit is less affected by air bubbles.

5 ± 9 (9) ø5 Sample inlet ø9 -ø ± (9) ME-6TNH PF, horizontal hole ( type, internal thermistor ) 9 ø Sample outlet -ø 9 Case 9 Thermistor Case ø5 Sample inlet ø9 -ø ø5 ø9 ME-6TTH PF, horizontal hole ( type, external thermistor ) ø Sample outlet -ø ø5 ø9 Fluorine resin (PF), horizontal hole type, cell constant.6/cm ME6T-- 8 lphabet: Z With/without casing material ME-6T N Not provided ME-6T H FCD/liquid contact surface PF lining provided Standards for case connection (flange) 5 JIS K RF equivalent "NSI 5L RF equivalent No applicable: (without case) Thermistor mounting method ME-6TN Internal detection end type (standard) ME-6TT External type Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM- model Japanese(standard) N/. For case-free models, inform us of the mounting conditions (whether you are using our proprietary case or your own measurement tank). If you intend to mount this unit on your own measurement tank, you will need an internal diameter of or more to comply with the cell coefficient.. The temperature compensation thermistor is usually built into the detection end (internal type). If the sample water temperature is prone to sharp fluctuations over short periods, select an external type because it responds more rapidly to temperature fluctuations. The withstand voltage of the external thermistor type is. MPa.. The standard cable length (external diameter 8 mm) is 5 m. If you require a cable of more than 5 m in length, select (Specify) and enter the necessary length (up to maximum m).. If a transmitter is indicated as Not provided, inform us of the model name and production number of the transmitter that you are using. Note : The liquid contact material of this sensor is made from PF and its maximum withstand voltage is. MPa. The maximum sample water temperature is C. However, for the external thermistor type, the withstand voltage is. MPa. Note : The detection end of the ME-6T model is a vertical hole type, making it appropriate for measurement of sample water flowing vertically. The detection end is designed to prevent the effect of air bubbles. Even if air bubbles are mixed in sample water, they do not mount to the detection end. The detection end of the ME-6T model is a horizontal hole type, making it appropriate for measurement of sample water flowing horizontally. Thus, when choosing a unit with case, the ME-6T H model or a vertical hole type is recommended because this type of unit is less affected by air bubbles.

6 8± ME-6ENH PVC, slanting hole type, ( internal thermistor ) (9) 8 Sample inlet ø5 ø9 ø -ø9 8 Case Sample outlet ø5 ø9 -ø9 ME-6EGH / ME-6ESH (PVC, slanting-hole type, external thermistor) Fluorine resin (PF), vertical hole type, cell constant.6/cm ME6E-- C lphabet: Z ME-6E N ME-6E H ME-6EN ME-6EG ME-6ES Material used for liquid contact components Hard PVC (standard) Heat-resistant PVC (C-PVC) Presence/absence of a case and standards for connection (flange) Not provided Provided: 5 JIS K FF equivalent (standard) Provided; 5 JIS K RF equivalent Provided: "NSI 5L RF equivalent Thermistor mounting method Internal detection end type (standard) External type External tube: glass External type External tube: SUS6 Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM- model Japanese(standard) N/ 8± (9) Thermistor 8 Sample inlet ø Sample outlet 8 Case ø5 ø9 ø5 ø9 -ø9. For case-free models, inform us of the mounting conditions (whether you are using our proprietary case or your own measurement tank). If you intend to mount this unit on your own measurement tank, you will need an internal diameter of or more to comply with the cell coefficient.. The temperature compensation thermistor is usually built into the detection end (internal type). If the sample water temperature is prone to sharp fluctuations over short periods, select an external type because it responds more rapidly to temperature fluctuations. If the sample water is acidic, select an external glass tube. If the sample water is alkaline, select a SUS6 external tube.. The standard cable length (external diameter 8 mm) is 5 m. If you require a cable of more than 5 m in length, select (Specify) and enter the necessary length (up to maximum m).. If a transmitter is indicated as Not provided, inform us of the model name and production number of the transmitter that you are using. -Ø9 Note : The liquid contact material of this sensor is made from PVC or C-PVC. Its maximum withstand voltage is. MPa and the maximum sample water temperature is 6 C for hard PVC and 7 C for heat-resistant PVC. Note : This sensor serves as a concentration meter for measuring a wide range of substances, including sodium chloride (NaCl), hydrochloric acid (HCl), and caustic soda (NaOH). In addition, it can measure nitric acid (HNO) up to % and sulfuric acid (HSO) up to %. Note : The detection end is of a slanting-hole type. The slanting-hole type of sensor is less affected by air bubbles because it does not attract air bubbles in sample water.

7 Specifications Model Liquid contact material / detection end / entire shape Flange standards Thermistor structure (material) Temp. Sample Conditions Pressure Flow rate Weight ME-6TNH PF / vertical hole type / with case 5 JIS K RF Internal detection end - C.MPa or less - L/m pprox.9kg ME-6TNN ME-6TTH ME-6TTN / without case / insertion length 9mm PF / vertical hole type / with case / without case / insertion length 9mm JIS 5K RF 5 JIS K RF JIS 5K RF External (PF) - C - C - C.MPa or less.mpa or less.mpa or less m/s or less - L/m m/s or less pprox.8kg pprox.9kg pprox.8kg ME-6TNH PF / horizontal hole type / with case 5 JIS K RF Internal detection end - C.MPa or less - L/m pprox.9kg ME-6TNN ME-6TTH ME-6TTN / without case / insertion length 9mm PF / horizontal hole type / with case / without case / insertion length 9mm JIS 5K RF 5 JIS K RF JIS 5K RF External (PF) - C - C - C.MPa or less.mpa or less.mpa or less m/s or less - L/m m/s or less pprox.8kg pprox.9kg pprox.8kg ME-6ENH PVC / slanting hole type / with case 5 JIS K FF Internal detection end - 6 C.MPa or less - L/m pprox.kg ME-6ENN ME-6ESH ME-6ESN ME-6EGH ME-6EGN / without case / insertion length 9mm PVC / slanting hole type / with case / without case / insertion length 9mm PVC / slanting hole type / with case / without case / insertion length 9mm JIS 5K FF 5 JIS K FF JIS 5K FF 5 JIS K FF JIS 5K FF External (SUS6 tube) External (glass tube) - 6 C - 6 C - 6 C - 6 C - 6 C.MPa or less.mpa or less.mpa or less.mpa or less.mpa or less m/s or less - L/m m/s or less - L/m m/s or less Note: For measurement sample water that fluctuates significantly in temperature, select an external thermistor type. pprox.kg pprox.kg pprox.kg pprox.kg pprox.kg

8 t f t f High-sensitivity immersion type Dimensions ME-7T øc øg ød Unit : mm N-øh (L+)± - L±5.5 Product code Fluorine resin (PF) vertical hole type; cell constant.6/cm 5 5 lphabet: Z Standards for connecting flange 8 JIS K RF (Minimum size) JIS K RF (Standard) 5 JIS K RF 5 JIS K RF Flange-bottom length (nominal dimension) 9mm (minimum) 5mm (standard) mm 5mm mm Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM- model Japanese(standard) N/ ME-7T.5 ø (56.5) øg ød ø (5) 9 (L+)± - L±5.5 Fluorine resin (PF) horizontal hole type; cell constant.6/cm ME7T-- ME7T lphabet: Z Standards for connecting flange 5 JIS K RF (Minimum size) 65 JIS K RF 8 JIS K RF JIS K RF (standard) 5 JIS K RF 5 JIS K RF Flange-bottom length (nominal dimension) 9mm (minimum) 5mm (standard) mm 5mm mm Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM- model Japanese(standard) N/ Nominal pressure K flange N.D ød t f øg øc N - øh 5 ø55 6 ø96 ø - ø9 65 ø75 8 ø6 ø - ø9 8 ø85 8 ø6 ø5 8 - ø9 ø 8 ø5 ø ø9 5 ø5 ø8 ø 8 - ø 5 ø8 ø ø 8 - ø N.D.=Nominal Diameter. lthough the minimum size is 5, if the internal surface of the 5 pipe in the mounting component (counterpart) has a lining, the internal diameter may be too small, preventing insertion of the pipe. Thus, the flange size should be 65 or more.. The standard length of cable (external diameter of 8 mm) is 5 m. However, if the bottom length (nominal dimension) of sensor flange is, for example, mm, then effective length of cable is. m. When you need a length of more than 5 m, select Specify to inform us of the necessary length (maximum of m, including sensor length).. If a transmitter is indicated as Not provided, inform us of the model name and production number of the transmitter that you are using. Note : In this sensor, PF is used as the liquid contact material. The detection end incorporates a temperature compensation thermistor. Note : The detection end is a horizontal hole type and is appropriate for sample water flowing horizontally. If the presence of air bubbles in sample water is suspected, we recommend selecting the ME-7T model, which is a vertical hole type, which is less affected by air bubbles. Note : The maximum withstand voltage is. MPa, and the maximum sample water temperature is C. Note : SUS6 is used as the flange material. The liquid contact surface is protected with a PF sheet.

9 t Dimensions ME-7E ø 9 () øc Unit : mm ød N-øh L±5.5 Nominal pressure K flange N.D ød t øc N - øh 65 ø75 ø - ø9 8 ø85 ø5 8 - ø9 ø ø ø9 5 ø5 ø 8 - ø 5 ø8 6 ø 8 - ø (L+8)± Product code PVC slanting-hole type; cell constant.6/cm ME7E-- 5 lphabet: Z Standards for connecting flange 65 JIS K FF (Minimum size) 8 JIS K FF JIS K FF (Standard) 5 JIS K FF 5 JIS K FF Material used for liquid contact components Hard PVC (standard) C-PVC (Heat resistant PVC) Flange-bottom length (nominal dimension) 5mm (standard) mm 5mm mm Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM- model Japanese (standard) N/. If the flange bottom length (nominal dimension) is 5 mm or mm, weld a reinforcement rib onto the pipe (nominal ) and the bottom of the flange to enhance agitation resistance. This will give a connecting flange of or more. The standard length of the cable (external diameter 8 mm) is 5 m. However, if the bottom length (nominal dimension) of the sensor flange is, for example, mm, then the effective length of the cable will be. m. If you need a cable of more than 5 m in length, select Specify to inform us of the necessary length (up to m, including sensor length).. If a transmitter is indicated as Not provided, inform us of the model name and production number of the transmitter that you are using. Note : In this sensor, PVC or C-PVC is used as the liquid contact material temperature compensation thermistor is incorporated into the detection end. Note : The maximum withstand voltage is. MPa. The maximum sample water temperature is 6 C for PVC and 7 C for C-PVC. Note : This sensor serves as a concentration meter for measuring a wide range of substances, including sodium chloride (NaCl), hydrochloric acid (HCl), and caustic soda (NaOH). In addition, it can measure nitric acid (HNO) up to % and sulfuric acid (HSO) up to %. Note : The detection end is of a slanting-hole type. The slanting-hole type of sensor is less affected by air bubbles because it does not attract air bubbles in sample water. Specifications Model ME-7T ME-7T ME-7E Liquid contact material Shape of detection end PF vertical hole type PF horizontal hole type PVC slanting-hole type Flange standards JIS K RF JIS K FF Flange bottom length 5 - mm Thermistor structure Internal detection end Temp. - C - C - 6 C Sample Conditions Pressure.MPa or less.mpa or less.mpa or less Flow rate m/s or less m/s or less m/s or less Weight 5mm pprox.kg pprox.kg pprox.kg Flow rates are limited by the flange bottom length.

10 High-sensitivity ME-T (multi-use) model Product code Fluorine resin (PF), horizontal hole type, cell constant.6/cm MET-- C D E 5 8 lphabet: Z 8 C D Mounting methods Sensor body (G/ screw type) Immersion type with extension tube (PF) Screw type (R R screw) IDF flange (ferule) type Throw-in type (holder material PVC) Length of immersion type extendable tube (PF) 8 mm (total length L: 9) 9 mm (total length L: 5) 89 mm (total length L: ) 9 mm (total length L: 5) 89 mm (total length L: ) Not applicable (sensor body, screw, IDF flange, throw-in type) Screw material for screw type SUS6 C-PVC Not applicable (sensor body, immersion type, IDF flange, throw-in type) Screw size of screw type R R / R Not applicable (sensor body, immersion type, IDF flange, throw-in type) Size of IDF flange type IDF / IDF IDF / IDF Not applicable (sensor body, immersion type, screw, throw-in type) Cable length Specified (maximum m) For MDM-, MM-, and MM-6 models For MDM-/ models Japanese (standard) N/. Only in the immersion type, an extension tube (PF) can be welded and connected to the detection end. If the R screw type or the IDF flange type needs an extension tube, the ME- Series is recommended.. Only SUS6L is used as the material for the IDF flange (ferule).. The standard cable length from the sensor body is 5 m. If the total length of the extension tube is m, then the effective cable length will be m. s a special case, it is possible to manufacture a cable of up to m including the length of the sensor.. If a transmitter is indicated as Not provided, inform us of the model name and production number of the transmitter that you are using. Note: This sensor can be used in various styles; mounted with a screw (G/R)/IDF flange, immersed in an open tank, or thrown in.

11 Dimensions Unit : mm Sensor unit type Dedicated cable Immersion type with extension tube Throw-in type Cable support Mounting component Fixing nut Packing Detecting element Thermistor ø (ø) 5 G/ ±5.5 Extension tube L±5.5 (L+)± Main body (PVC) Wire 55±5.5 Max.: approx. 8 Storage tube (PVC) ø ø6 IDF flange (ferule) type ø ø Screw type Dedicated cable (D) Clamp ( /=K) Ferule Plug size R C R 8 R R R (E) (G) Ferule gasket 5±5.5 -surface Plug R C 5±5.5 ( /S=F) (F) (øc) Electromagnetic concentration detector Nominal IDF /S IDF S IDF /S IDF S ø ø øc ø 77.5 ø 6.5 ø59.7 ø 9 ø6 ø9 ø 76. ø7.5 ø 89. ø85. ø.6 ø97.8 Clamp joint dimension ød ø 88 ø6 E 5 8 F ø K 6 K 6 K ø G 8 K

12 Combination electromagnetic conductivity meter/concentration meter transmitter Field installation type (-cable type) MDM-5 / MDM-7 Field installation type (-cable type) MM-6/ MM-6 Compact solid aluminum casting structure (IP55); simple field installation type unit Two-cable power supply DC V djustable transmission output range (DC m) Transmission output maintained during maintenance Measurement value shift; cell constant settings; temperature display function provided as standard Measurement range MDM-5: minimum - 5µS/cm maximum - ms/cm MDM-7: - 5%HCl, %HSO, - %NaOH, - %NaCl etc Panel mounting type MM- / MM- Compact solid aluminum die cast structure (IP65); field installation type unit C V free power supply djustable transmission output range (DC m) Transmission output of sample water temperature (DC m) Threshold alarm contact output Transmission output maintained during maintenance Measurement value shift; cell constant settings; a temperature display function provided as standard Measurement range MM-6: minimum - 5µS/cm maximum - ms/cm MM-6: - 5%HCl, %HSO, - %NaOH, - %NaCl etc Compact DIN96 size; lightweight (.5 kg) panel type unit C V free power supply djustable transmission output range (DC m) Threshold alarm contact output Transmission output maintained during maintenance Measurement value shift; cell constant settings; a temperature display function provided as standard Measurement range MM-: minimum - 5µS/cm maximum - ms/cm MM-: - 5%HCl, %HSO, - %NaOH, - %NaCl etc Please read the operation manual carefully before using producuts. Overseas Sales Division: DKK-TO Corporation 9-, -Chome, Takadanobaba, Shinjuku-ku, Tokyo Japan Tel : Fax : Information and specifications are subject to change without nofice. Issued on 8//6