JFR Series FMCW Radar Level Transmitter.

Transcription

1 JFR Series FMCW Radar Level Transmitter

2 PRODUCT INTRODUCTION FMCW Radar level transmitter is a non contact measuring device, which is suitable for high temp., high pressure, and corrosive applications. It is easy to install and free of maintenance, especially for the high accuracy requirement environment. PRINCIPLE FMCW radar adopts a high frequency signal, which is emitted via an antenna and swipe frequency increment by 0.5GHz during the measurement, reflected by the target surface and received at a time delay. The frequency difference, which is calculated from the transmitting frequency and the received frequency, which is directly proportional to the measured distance (or material surface). The frequency difference then is processed by Fast Fourier Transformation (FFT) to identify the signal in Intermedium Frequency (IF). This FMCW radar is innate with signal / noise enhancement and filtering of echo-back via Phase-Lock Loop (PLL) circuit that is the best solution for complex environment and high accuracy measurement. Design formula FEATURES Non contact measuring Corrosive and toxic liquid, hydrocarbons, slurries Not affected by specific gravity, pressure, temperature, viscosity, foam, and dust 5 digits LCM display Indicate signal wave inside the silo. Selection of Different Measurement unit(m, cm, mm, inch, ft, %, ma) Measuring distance and actual level. Language selection of traditional Chinese, simplified Chinese, English. 4-0mA/ 4 lead wires Modbus RS-485 to enhance isolation and easy for remote control. CE standards for isolation(eft 000V, B class or better) Suitable for mid-range signal 4mA, 0mA output Set functions to the continuous measuring device via FAS software. Isolated circuit design. 10GHz JFR1 series could measure liquid material. 6GHz JFR series could measure all kinds of material. LINEARITY DIAGRAM Accuracy cm A30mm A0mm A10mm A5mm A3mm A0.4% A0.4% A0.4% A0.% A0.% 0.5m 5m 15m 0m Distance to flange 1 TEST STANDARDS High voltage : IEC Isolated resistance : IEC Power supply change : IEC Power supply failure : IEC Electrical burst testing : IEC Voltage DIPS : IEC Humidity : IEC High/Low temperature test : IEC IP protection rating : IEC6059

3 SPECIFICATION (6GHz 4-wire) f98 f98 Dimensions (Unit:mm) 1/"PF "10K SUS /"PF PTFE f /"PF -1/"10K PTFE "PF PTFE f Model Medium Min. Dielectric constant (solid) Min. Dielectric constant (liquid) Measuring range Accuracy Repeatability JFR-04 General liquid and solid Liquid 30m Solid 0m A3 mm A1 mm JFR-14 General liquid /suitable for acid and alkaline in liquid Liquid 30m Digital communication Ambient temperature Operating temperature Operating pressure Frequency Analog output Protection rating Power supply Local display Housing material RS485 (Isolated) -40~90 BC -40~00 BC 0~40 bar K Band 4~0mA / 4 Wire IP67 9.5~30Vdc 5 digits LCM display Aluminum Antenna type Horn (43D) Lens (56D) Half-power beam width ±9 Antenna material SUS316+PTFE PTFE Blind distance 500mm

4 SPECIFICATION (6GHz 4-wire) f98 f98 f98 1/" PF Compressed air input 1/" PF Compressed air input 1/" PF 1-1/" PF 190 Dimensions (Unit:mm) 4" 10K " 10K " 10K f4.5 f100 f140 Model JFR-4 JFR-34 JFR-44 Medium Suitable For Min. Dielectric constant (solid) Measuring range Accuracy Repeatability Long dlstance measurement A3 mm General liquid and solid Min. Dielectric constant (liquid) 1.4 Liquid 30m Solid 0m Super dlstance measurement 1.5 A1 mm Corrosion type acid and alkaline liquid Liquid 70m Solid 50m Liquid 0m Solid 15m A3 mm Digital communication RS485 (Isolated) Ambient temperature -40~90 BC Operating temperature -40~00 BC Operating pressure 0~40 bar Frequency K Band Analog output 4~0mA / 4 Wire Protection rating IP67 Power supply 9.5~30 Vdc Local display 5 digits LCM display Housing material Aluminum Antenna type High gain horn (100) High gain horn (140) Lens(43DS) Half-power beam width ±5 ±3 ±10 Antenna material Blind distance SUS mm PTFE P.S. For JFR-4 and JFR-34, customer can connect the compressed air with 1/8"PT thread connector to avoid dust adhered. 3

5 SPECIFICATION (10GHz 4-wire) f117 f /"PF 03 1/"PF Dimensions (Unit:mm) 6"10K 0 4"10K 16 f140 f100 Model JFR-10 JFR-11 Medium Min. dielectric constant Accuracy (1m~5m) Repeatability General liquid, corrosion liquid (coating).5 A5mm A1mm Measuring range 30m 0m Digital communication Ambient temperature Operating temperature Operating pressure Frequency Analog output Power consumption Protection rating Power supply Local display Housing material RS485(Isolated) -40~70BC -40~00BC 0~40 bar X Band 4~0mA / 4 Wire 100mA/ 4Vdc IP65 4VdcA10% 5 digits LCM display Aluminum Antenna type Horn(140D) Horn(100D) Half-power beam width ±10 ±8 Antenna material Sampling rate Blind distance SUS 316/ ETFE Coating 1 sec. 500 mm 4

6 SPECIFICATION (10GHz 4-wire) f /"PF Dimensions (Unit:mm) f4 L=45/65/85 f16 Model Medium Min. dielectric constant Accuracy (1m~5m) Repeatability Measuring range Digital communication Ambient temperature Operating temperature Operating pressure Frequency Analog output Power consumption Protection rating Power supply Local display Housing material Antenna type JFR-13F / JFR-14F/ JFR-15F General liquid, corrosion liquid (coating) 4 A0mm A1mm 10m RS485(Isolated) -40~70BC -40~150BC 0~16 bar X Band 4~0mA/ 4 Wire 100mA/ 4Vdc IP65 4VdcA10% 5 digits LCM display Aluminum Rod antenna Half-power beam width ±11 Antenna material Sampling rate Blind distance PTFE 1sec. 600mm 5

7 WIRING/CALIBRATION WIRING INFORMATION CALIBRATION RS485 wiring TR- TR+ V+ V- POWER DC4V Two ways to calibrate the JFR Series: 1. With display/adjustment module. By PC based FAS software Adjustment module is an adjustment tool with 4 buttons to click on. It also has a transparent window to allow display reading. RS3/485 Converter RS3 Interface/ USB Interface JFR Series and Indicator(External Power) V+ V- POWER DC4V 5 digits LCM display I+ I- Panel Meter JFR Series and Indicator(Powered by panel meter) [ ] Button -Enter Edit status -Confirm Edit -Confirm parameter modification [ ] Button -Select Edit -Select parameter -Parameter V+ V- I+ I- Panel Meter [ ] Button -Return -Cancel [ ] Button -Increase -Select WIRING DIAGRAM JFR-1 JFR Power Supply: V+ Power Supply: V- Analog Output: I+ (4~0mA) Analog Output: I- (4~0mA) Communication : TR+ (RS485) Communication : TR- (RS485) 6

8 PARAMETER SETTING Measurement bench-mark starts at contact surface of connection. Low level calibration High level calibration Blind Distance Measuring Distance Setup Note: Be aware of blind distance when measuring material high level.(shown in ) 100% 0% 7

9 SOFTWARE SETUP CALIBRATION Software Setup Calibration(FAS) FAS calibration software can be utilized with JFR Series via RS485/RS3 to allow tank data reading and setup from PC. Parameter Description Low Point: Low point(4ma), measuring range from flange to low level. High Point: High point(0ma), measuring range from flange to high level. Blind Area: Blind distance, distance starts from flange surface. Max. Distance: Measuring range between low point nd high point. FAS Operation Instruction 1. Turn on FAS software. Go to Address, then choose 9600, COM5 from baudrate 3. Click on Connect. 4. Press "Stop Sync" to change parameter. 5. Press "GetFFT" to read wave reflection diagram. Press "Stop Sync" to change preset parameter. 8

10 INSTALLATION 1. Installation in the extension tube 1-1 JFR-13 series installation with extension tubes inside the tank, extension tube length and diameter is required to meet the requirements. 1-5 JFR-4 and JFR-34 can be hidden in the extension tube, the recommendation of the tube diameter D and length L are shown in the table. H L L Model JFR-13F JFR-14F Antenna length L 50mm min. Extension tube length 45 mm H mm H 360 JFR-15F 85 mm H JFR-10 and JFR-11 series horn antenna can be hidden in the extension tube the recommendation of the tube diameter D and length L are shown in the table. Model JFR-4 JFR-34 Diameter D (mm) Length L (mm) D>100 L 140 D>140 L JFR-44 can be hidden in the extension tube, the recommendation of the tube diameter D and length L are shown in the table. D Model JFR-10 JFR-11 D L Diameter D (mm) Length L (mm) D>140 L 70 D>100 L 140 Diameter D (mm) Length L (mm) D " L 100-3/4" L /8" L /8" L 380 L 1-3 JFR-04 can be hidden in the extension tube, the recommendation of the tube diameter D and length L are shown in the table. Diameter D (mm) Length L (mm) D 50 L L 0 85 L L JFR-14 can be hidden in the extension tube, the recommendation of the tube diameter D and length L are shown in the table. L 1-7 Installation recommendations are as follows : 1. Antenna installation angle to be perpendicular to the Horizontal.. JFR installation position with the drum wall suggestions Are as follows : Installation location A should be less than 1/6D Range with A relation is as follows : a.h<10m, A>300mm b.10m<h<0m, A >600mm c.h>0m, A>900mm H A Diameter D (mm) D L Length L (mm) 70 L L L D

11 INSTALLATION. Radar installation should not be too close to the drum wall, avoid the drum wall attachment material reflection interference. 6. If drum internal agitator will have a strong vortex and foam, drum must increase waveguide, the upper waveguide drill vent holes to ensure the correctness of the measured value. X X vent hole 3. Radar installation not too close to the drum bracket to avoid reflection is incorrect 7. Installation should be avoided in the feed inlet position, avoid material interference or obstacles interference. X X 4. When obstructions inside the tank, tank be fitted with eflectors, steer clear of the error echo reflected to the receiver, causing radar miscalculation. 8. Installation should be avoided in the top center of the arch or round barrel will cause multiple echo reflections. Reflector X X 5. Outdoor installation should take shade or rain-proof measures. 10

12 ORDERING INFORMATION(6GHz) Antenna type 0: Horn(43D) 1: Lens(56D) : High gain Horn(100D) 3: High gain Horn(140D) 4: Lens(43DS) Wiring JFR- 0 4: 4-Wire Accuracy P: A3mm A: A5mm B: A10mm Connection type 0: Flange 1: Thread Connection specification Size for flange or screw Pressure range or other E: 1-1/"(40A) F: " (50A) G: -1/"(65A) H: 3" (80A) I: 4"(100A) J: 5"(15A) K: 6"(150A) S: Others M: 5kg/cm JIS N: 10kg/cm JIS O: 150Lbs ANSI P : 300Lbs ANSI R : PF U : NPT W: PN10 (10Bar) X: PN16 (16Bar) Y: PN5 (5Bar) Z: PN40 (40Bar) S: Others (1)JFR-04 thread connection 1-1/" only ()JFR-14 thread connection " only (3)JFR-4 thread connection 1-1/" only (4)Please do check Radar antenna can be direct fitted in flange connection and nozzle Below is the suggestion Flange material Type Opening Flange size JFR-14 56mm -1/" JFR-4 100mm 4" JFR mm 6" JFR-44 44mm " Metal 0: SUS304 5: SS41 zinc coating 6: SUS316 Plastic P: PP E: PTFE 11

13 ORDERING INFORMATION(10GHz) Type Material Accuracy 0: Horn Antenna Type3 (Length 0mm,opening140mm) Standard 1: Horn Antenna Type (Length 16mm,opening100mm) 3: Rod Antenna (Length 45mm) Standard 4: Rod Antenna (Length 65mm) 5: Rod Antenna (Length 85mm) 0: SUS304---Horn Antenna 6: SUS316---Horn Antenna E: ETFE------Horn Antenna with ETFE coating F: PTFE------Rod Antenna A: A5mm B: A10mm C: A0mm D: A30mm Flang connection Size for flange or screw Pressure range or other G: -1/"(65A) H: 3" (80A) I: 4"(100A) J: 5"(15A) K: 6"(150A) S: Others M: 5kg/cm JIS N: 10kg/cm JIS O: 150Lbs ANSI P : 300Lbs ANSI Please do check Radar antenna can be direct fitted in flange connection and nozzle Below is the suggestion ( 1) Horn Antenna Type Opening Flange size Flange material Type3 Type 140mm 100mm ( ) Rod Antenna Minimum size of flange is -1/" W: PN10 (10Bar) X: PN16 (16Bar) Y: PN5 (5Bar) Z: PN40 (40Bar) S: Others Metal 0: SUS304 5: SS41 zinc coating 6: SUS316 Plastic P: PP E: PTFE JFR R01 6" 4" 1

14 Global Network Germany China Taiwan U.S. U.S. Singapore Asia North America Europe Taiwan FINETEK CO., LTD. - Taipei Head Quarter No.16, Tzuchiang St., Tucheng Industrial Park New Taipei City 36, Taiwan TEL: FAX: info@fine-tek.com California, U.S. APLUS FINETEK SENSOR INC. - US Office 355 S. Lemon Ave, Suite D, Walnut, CA TEL: FAX: info@aplusfine.com Germany FineTeK GmbH - Germany Office Frankfurter Str. 6, OG D-6548 Ruesselsheim, Germany TEL: +49-(0) FAX: +49-(0) info@fine-tek.de FINETEK CO., LTD. - I-Lan Factory TEL: FAX: FINETEK CO., LTD. - Taichung Brance TEL: FAX: Illinois, U.S. APLUS FINETEK SENSOR INC. TEL: FAX: info@aplusfine.com FINETEK CO., LTD. - Kaohsiung Branch TEL: FAX: China FINE AUTOMATION CO., LTD. - Shanghai Factory No.451 DuHui Rd, MinHang District, Shanghai, China TEL: FAX: info.sh@fine-tek.com Distributor: Singapore FINETEK PTE LTD. - Singapore Office No. 60 Kaki Bukit Place, #07-06 Eunos Techpark Lobby B, Singapore TEL: FAX: info.sg@fine-tek.com 08-JFR-B0-EP, 08/8/015