MP 08 V. USER s MANUAL. Paseo Miramón Donostia - San Sebastián, Guipúzcoa /Spain -
|
|
- Antony Wood
- 5 years ago
- Views:
Transcription
1 MP 08 V USER s MNUL Paseo Miramón Donostia - San Sebastián, Guipúzcoa /Spain - tlc@ikusi.com
2 0- SFETY INSTRUCTIONS These instructions must be read carefully in order to install and use the set properly and to keep it in perfect working condition and to reduce the risks of misuse. Do not use this set on machines in potentially explosive atmospheres, except the models certified TEX/RTEX to work in that conditions. a) Strictly adhere to the instructions for installation contained in this manual. b) Make sure that professional and competent personnel carry out the installation. c) Ensure that all site and prevailing safety regulations are fully respected. d) Make sure that this manual is permanently available to the operator and maintenance personnel. e) Keep the transmitter out of reach of unauthorised personnel. f) Remove the transmission key when the set is not in use. g) On starting each working day, check to make sure that the STOP button and other safety measures are working. h) When in doubt, press the STOP button. i) Whenever several sets have been installed, make sure the transmitter you are going to use is the right one. Identify the machine controlled on the label for this purpose on the transmitter or by using the display (in case it has one). j) Service the equipment periodically. k) When carrying out repairs, only use spare parts supplied by IKUSI dealers. WRNING The devices muts be used with the manufacturers battery and battery charger. The equipment must be operated by quialified personnel. fter use, never leave the equipment ON (one or several transmitters). lways set the contact key and the STOP button to switch off position of the equipment to avoid accidentally to activate manoeuvres specially in crane maintenance purposes-. Do not use the set when visibility is limited. void knocking or dropping the set. Do not use the set if failure is detected. REMEMER Changes or modifications not expressly approved by IKUSI could void the user s authority to operate this equipment. 0 Cr Remove the transmission key only when the set is not in use or to deny the access When in doubt, press the STOP button Tx Cr Make sure the transmitter works with the machine to be handled 0 fter use set the contact key and the STOP button Do not use the set when visibility is limited void knocking or dropping the set 0- SFETY INSTRUCTIONS
3 0- TECHNICL DESCRIPTION Fixing slots (fixed assembly or anti-vibration).- Deustch Connector 3.-External ntenna 0 (433) or 70 (870) 4.- Removable internal EEPROM 5.- TR800-CE MCX Radio.- External signalling LEDs 7.-Deutsch Connector Pinout 8.- Switches for the control of voltage options 0- TECHNICL DESCRIPTION
4 03- RECEIVER s INSTLLTION WRNING Manage the complete shut down of the machine throughout the whole installation of the receiver, following the legislation on occupational risk presention in force. Check the power supply and shut down the main switch, disconnecting the interface cable between the receiver and the machine s electrical box. Remember that the receiver has more than one circuit of low tension. Even if the power supply of the receiver is not connected, there is still risk of electric shock. HOW TO LOCTE THE RECEIVER. Find a easily accesible and clear location, if possible with a direct vision between the receiver s antenna and the transmitter s working area.. In case it is difficult to achieve a direct vision between the receiver s antenna and the transmitter s working area, it is recommended the use of an extern antenna and the location of this antenna in clear areas with the antenna extension (in those models that allow an antenna). In areas where there s expected a high vibration level of the machine, the use of dampers is adviced. 3 PIUT MP08 7 IN 8 IN 9 MNUL 0 K PW K-4 S4 3 S3 4 S 5 S IN3 5 IN4 4 3 IN 0-0V IN 0-0m K4 K STOP +/4V S-4 S-3 S- S- PIUT MP08 V K. KSTOP. CNL 3. Proceed the connection of the power supply. Use the connection block diagram provided with the system, 5 where it is detailed the correspondence between the transmitter maneuvres 4 3 and the receiver s outputs. In 0-0 K8 K4 K Power K K-8 K. KSTOP. +/4V CNH S S Diferencias entre MP08 y MP08V 4. Check the electrical installarion and verify if there s an option to connect the neutral or the ground cable. In that case, don t forget to connect the ground cable. The use of fireproof or flame retardant cables is recommended for the connection. 7 IN 8 IN 9 K7 0 K5 K 3 4 S4 5 S 03- RECEIVER INSTLLTION
5 03.- INPUTS / OUTPUTS CONFIGURTION The MP08 includes a 7.5 internal fuse. This receiver has one analogue input IN 0-0V (without isolation) or IN 0-0m (without isolation). These inputs share the same hardware/pins and each one is selected by an internal jumper. The two inputs can not be live together at the same time DIGITL OUTPUTS MP08V The digital outputs k-k8 have a common contact at pin of the connector. Maximun per output. It is recommended to use K for by-pass valve. Pin Emergency Stop Output external connection K K K4 K5 K K7 K8 Pin Pin Pin Pin Pin 3 Pin 0 Pin 4 Pin 9 Pin 5 Deutsch Connector NLOGUE OUTPUTS MP08V MP08V allows to choose the control voltage to set up the output power, throughout the selection of switch. Control voltaje options: 0-5V 0-0V 0-Vcc SLID NLÓGIC 7 SLID NLÓGIC 5 SLID NLÓGIC 3 8 SLID NLÓGIC RECEIVER INSTLLTION
6 STOP Category 3 PLd (only in MP08V): Stop function is performed with relays in serie or in parallel. SERIE PRLLEL PRLELO conexi n externa 0 Vdc 0 Vdc conexi n externa STOP +IN +IN STOP STOP +OUT STOP +IN alimentaci n salidas digitales -8 STOP +OUT alimentaci n salidas digitales -8 STOP +OUT PIUT 7 IN 8 IN 9 K7 0 K5 K 3 K. KSTOP. CNL 4 S4 5 S In K8 K K4 K Power K-8 K. KSTOP /4V CNH S S 03- RECEIVER INSTLLTION
7 04- TROULESHOOTING ORDER RELY ID DT SIGNL HRDOK POWER CNRUN* CNERR* LED COLOUR CONDICIONES REMRKS PROPOSED CTION POWER GREEN Switch ON if powered. Power supply OK. Check the power supply. GREEN Solid green LED if no error detected linking during start up process Receiver hardware OK OK Please wait to finish the startup process HRDOK RED If there s an error of: - Watchdog activated / oscillator stopped / wrong EEPROM checksum - Reset activated. Electronic board hardware breakdown Replace electronic -linking if checksum EEPROM error/ Data corrupted / bus CN error detected-> CN-ERR Reprogram EEPROM SIGNL GREEN LED Off if no radio signal detected (Squelch). - LED On and the transmitter switched Off indicates occupied radio channel - LED On and DT switched Off indicates radio channel occupied by a non IKUSI system Change Transmitters Frequency Channel DT GREEN Switch off if the received frame has an error linking if receiving good frames Switch off and LED SIGNL switched on: Radio error Replace radio ID GREEN linking if a correct ID is received Switched Off and DT LED switched On: no valid ID (ikusi system nearby) SIGNL; DT and ID LED On, indicates valid frames from the transmitter. Correct link. If channel not occupied: Check chosen ID in the transmitter or reset the receiver. OK. RELY GREEN STOP relay activated ORDER GREEN TROULESHOOTING
English RACON SERIES II RADIO CONTROL SERVICE MANUAL
English 22.2.2007 RACON SERIES II RADIO CONTROL SERVICE MANUAL Read the instructions supplied with the product before installation and commissioning. Keep the instructions in a safe place for future reference.
More informationRF Remote Control Unit SEAV
RF Remote Control Unit SEAV for LINAK TECH-systems Installation instructions Foreword Dear producer, Thank you for choosing an actuator system from LINAK. LINAK systems consist of high-tech products based
More informationTM70 PUSHBUTTON TRANSMITTERS
OPERATION & INSTALLATION MANUAL TM70 PUSHBUTTON TRANSMITTERS TM70 PUSH BUTTON V11.doc (01/07) IKUSI reserves the right to modify this information without prior notification. I N DEX PAGE. 1.- DECLARATION
More informationINSTRUCTION MANUAL. IBRit - rf1 - usb PC - Station for wireless Data transmission. M e s s t e c h n i k. Messtechnik GmbH & Co.
M e s s t e c h n i k INSTRUCTION MANUAL PC - Station for wireless Data transmission Document No. : D1F604 001 Version : April 2006 Copyright : IBR Messtechnik GmbH & Co. KG Contents 1. Introduction 1.1
More informationI-syon MR11. Radio remote system for hoisting applications
I-syon MR11 Radio remote system for hoisting applications CHARACTERISTICS: Radio remote system for hoisting applications -overhead cranes- NON COMPATIBLE with safety standard Cat.3 CE EN-954-1 or EN 13849.
More informationTM70 CONSOLE TRANSMITTER
OPERATION & INSTALLATION MANUAL TM70 CONSOLE TRANSMITTER TM70 JOYSTICK V23.doc (01/07) IKUSI reserves the right to modify this information without prior notification.. I N DEX 1.- DECLARATION OF CONFORMITY...1
More informationCCR24T CCR24R. User s Guide WIRELESS TRANSMITTER SYSTEM WARRANTY SERVICE CARD WARRANTY CARD
WARRANTY SERVICE CARD WARRANTY CARD PRODUCT NAME Wireless Transceiver System PERIOD MODEL NAME CCR24GEN YEAR PURCHASE DATE.. 200_ From the date of WARRANTY PERIOD.. 200_ purchase. CUSTOMER S ADDRESS :
More informationPULSE/FREQUENCY/CONDITIONER USER GUIDE
PULSE/FREQUENCY/CONDITIONER USER GUIDE D2560-02-02 CN5220 1600F USER GUIDE Page 1 of 13 PULSE/FREQUENCY/CONDITIONER USER GUIDE FREQUENCY INPUT PSU 1 2 + - SUPPLY (to4) Vdc (to32) Vac UNIVERSL Excitation
More informationFCC ID: SAGA1-L8 IC: 2802A-SAGAL8 CE0470
FCC ID: SAGA1-L8 IC: 2802A-SAGAL8 CE0470 WARRANTY INMOTION Controls, Inc. guarantees that this product meets its published specification at the time of shipment from the factory. Under proper installation,
More informationCoin control unit. Operating instructions C 4065
Operating instructions Coin control unit C 4065 G To avoid the risk of accidents or damage to the machine it is essential to read these instructions before installing, commissioning and using it for the
More informationBlue Point Engineering Inc.
Engineering Inc. ireless Radio Control of Puppets Setup Overview RF Control C Pointing the ay to Solutions! Hardware Setup Overview Page 1 Servo No.1 Servo No.2 Control Signal Line RX8ch1,2 Servo Board
More informationC-Bus 8 Channel Low Voltage Relay
SLC5108RELVP Instruction Bulletin Retain for future use. 63249-420-325A1 Instruction Bulletin 07/2009 HAZARD CATEGORIES AND SPECIAL SYMBOLS Read these instructions carefully and look at the equipment to
More informationINSTALLATION AND OPERATION MANUAL
RADIO/CAN REMOTE CONTROL SYSTEM -PRELIMINARY- INSTALLATION AND OPERATION MANUAL SDP GREEN 3B1151AJ.doc September 3, 2009 AP INDEX DESCRIPTION... 2 TRANSMITTER AND RECEIVER SYNCHRONIZATION... 3 INDICATOR
More informationVFSC9 ELECTRONIC SPEED CONTROLLER. Mounting and operating instructions
ELECTRONIC SPEED CONTROLLER Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5 WIRING
More informationElectric Crane Remote
Manual Part # 99904431 Electric Crane Remote Revised 20080423 Version 2 IOWA MOLD TOOLING CO., INC. PO Box 189 Garner, IA 50438 Tel: 641-923-3711 FAX: 641-923-2424 Website: http://www.imt.com Copyright
More informationTelescopic Crane. Installation / Configuration Manual. T150 Transmitter R160 Receiver. March 20, Revision 6
Telescopic Crane Installation / Configuration Manual T150 Transmitter R160 Receiver March 20, 2006 99903661 Revision 6 This page is intentionally left blank. 2 Table of Contents System Overview... 4 Features...
More informationGENERIC. Installation / Configuration Manual. T110 Transmitter R130 Receiver. Revised May 23, Version 4. DMAN - xxxx - xx
GENERIC Installation / Configuration Manual T110 Transmitter R130 Receiver Revised May 23, 2006 Version 4 DMAN - xxxx - xx #74-1833 Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604) 944-9247
More informationPower Genius XL User Manual rev 10.
Power Genius X User Manual rev 10. 1/23 Table of Contents 0. Important notice...3 1. Unpacking...5 1.1. Front Panel...5 1.2. Back Panel...6 1.3. BCD/PTP connector pinout...8 2. Using with Radios...9 2.1.
More informationIS7705. Installation & Operation Manual AUDIO INTEGRATION KIT. TranzIt LINK
GET CONNECTED Installation & Operation Manual AUDIO INTEGRATION KIT IS7705 Note to Readers, The information contained within the following documentation is subject to change without notice. Features discussed
More informationw w w. p r o l i g h t. c o. u k
w w w. p r o l i g h t. c o. u k Order code: MIC45 Voco Artist (863.13MHz) MIC45A Voco Artist (863.65MHz) MIC45B Voco Artist (864.05MHz) MIC45C Voco Artist (864.82MHz) Order code: MIC46 - Voco Presenter
More information- Wiring Brochure Universal Reset Module 423e
- Wiring Brochure Universal Reset Module 4e W 4e 0/08 Information Brochure Choose controls to match application Application Brochure Design your mechanical applications Rough In Wiring Rough-in wiring
More informationMEGA REMOTE RADIO REMOTE CONTROL SYSTEM
RADIO REMOTE CONTROL SYSTEM -PRELIMINARY- INSTALLATION AND OPERATION MANUAL NORWOOD 3A2481CJ.doc April 15, 2014 BJ INDEX DESCRIPTION... 2 TRANSMITTER AND RECEIVER SYNCHRONIZATION... 3 CLONING TRANSMITTERS...
More informationeguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards
eguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards A. Primary Technical Data: Transmitter Operating voltage DC 24V Operating current. < 450mA
More informationCOD GB / 1.0 RBAND/UMS - RBAND/CSM
INTRODUCTION DESCRIPTION The RadioBand system is designed of Industrial, Commercial and Domestic door and gate applications where a safety edge is used. The system provides a wireless system replacing
More informationPRO 4 CHANNEL MULTI CHANNEL WIRELESS SYSTEM WITH DM4/DM4D DISTRIBUTION MODULE. OPERATING INSTRUCTIONS and trouble-shooting guide LECTROSONICS, INC.
PRO 4 CHNNEL MULTI CHNNEL WIRELESS SYSTEM WITH DM4/DM4D DISTRIUTION MODULE OPERTING INSTRUCTIONS and trouble-shooting guide LECTROSONICS, INC. Rio Rancho, NM INTRODUCTION The PRO 4 CHNNEL system is a high
More informationRADIOBAND V3 Programming & Installation Manual
RADIOBAND V3 Programming & Installation Manual Radioband V3 User s Manual Introduction The RadioBand system is designed for Automatic Gates, Commercial and Domestic door applications where a safety edge
More informationWiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers.
Wiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers. 92220.02E 1 1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5
More informationXARS8D18p / XARS12D18p / XARS8L12p Quick Start Guide
Quick Start Guide Harmony www.schneiderelectric.com www.schneiderelectric.com/control TM XARS8D18W / XARS8D18H / XARS12D18W / XARS12D18H exlhoist XARS8L12W / XARS8L12H DANGER HAZARD OF ELECTRIC SHOCK,
More informationGENERIC. User Installation / Configuration Manual. T110 Transmitter R170 Receiver. Revised February 9, Version 2 DMAN - XXXX-XX
GENERIC User Installation / Configuration Manual T110 Transmitter R170 Receiver Revised February 9, 2007 Version 2 DMAN - XXXX-XX #74-1833 Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604)
More information- Wiring Brochure Universal Reset Module 423
- Wiring Brochure Universal Reset Module 423 W 423 03/09 1 Information Brochure Choose controls to match application Application Brochure Design your mechanical applications 2 3 Rough-in Wiring Rough-in
More informationGENERIC. Installation / Configuration Manual. T110E Transmitter R100 Receiver. Revised May 23, Version 3. DMAN - xxxx - xx
GENERIC Installation / Configuration Manual T110E Transmitter R100 Receiver Revised May 23, 2006 Version 3 DMAN - xxxx - xx #74-1833 Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604) 944-9247
More informationKeychain Radio Remote Control System
Innovation in Mobility Keychain Radio Remote Control System Operator Manual 04/23/02 95-2002 RICON CORPORATION All Rights Reserved U.S. and foreign patents pending Printed in the United States of America
More informationBlue Point Engineering Inc.
nc. Wireless Radio Control of Puppets Setup Overview RF Control C Hardware Setup Overview Servo No.1 Servo No.2 Control Signal Line RX8-ch1,2 Servo Board WZ-12 RX8-ch3,4 Servo Board WZ-12 Power Line DC
More informationPRetrans Table of contents
HART TRANSPARENT REPEATER PRetrans 5106 Table of contents Warnings 16 Safety instructions 17 EC Declaration of Conformity 19 How to demount SYSTEM 5000 20 Application 21 Technical characteristics 21 Mounting
More informationAUDIO MODE SELECTOR MODEL AMS-6000
AUDIO MODE SELECTOR MODEL AMS-6000 Installation and Operating Instructions Til Document No. 03RE325 Rev. n/c Issue 4 August 2007 Technisonic Industries Limited 240 Traders Boulevard, Mississauga, Ontario
More informationInstallation & Operation Manual SAGA1-K Series Industrial Radio Remote Control
Installation & Operation Manual SAGA1-K Series Industrial Radio Remote Control Gain Electronic Co. Ltd. Table Of Contents Safety Considerations ------------------------------------------------------------2
More informationRADIOBAND 3G RB3 T868 RB3 R868 USER'S MANUAL
RADIOBAND 3G RB3 T868 RB3 R868 USER'S MANUAL Index INTRODUCTION... 3 Operating... 3 Receiver RB3 R868... 4 Transmitter RB3 T868... 5 ASSEMBLY AND INSTALLATION... 6 1 Installation of the equipment... 6
More informationFomotech International Corp.
Alpha 600 Series I n d u s t r i a l R a d i o R e m o t e C o n t r o l S y s t e m Operation & Parts Manual Fomotech International Corp. TABLE OF CONTENTS Page 1. SAFETY INSTRUCTION... 2 2. PUSHBUTTON
More informationParts and Service. Manual
Parts and Service Manual Manual # 99905492 16000SIII Radio Remote Control Revision Date: 05-03-2012 Table of Contents 1 G2B System Overview 3 2 CU Installa on and Wiring 4 2.A Loca ng the CU. 4 2.B Grease
More informationTele Radio 860. Manual. Rev. IM A1_MULTI
Tele Radio 860 Manual Rev. IM-860-005-A1_MULTI 1 CONTENTS 2-3 5-23 24-42 43-61 62-81 82-100 101-120 121-140 141-159 160-180............... 860TX/860RX............... Dansk............... Norsk...............
More informationFeatures. Rechargeable and waterproof. Controller
Rechargeable and waterproof Controller Features 1.100 levels of vibration. 2.100 levels of static(optional). 3.The levels can be altered by use of up & down button. 4.A tone button activates a tone on
More informationHAWK5000 Operators Manual
HAWK5000 Operators Manual Keison Products P.O. Box 2124, Chelmsford CM1 3UP, England Tel: +44 (0) 1245 600560 Fax: +44 (0) 1245 600030 Email: sales@keison.co.uk www.keison.co.uk KANE INTERNATIONAL LIMITED
More informationPanther. Installation instructions. Receivers PN-R15-1 PN-R15-2 PN-R15-13 PN-R IM-PN-RX103-A03-EN Language: English (original)
Panther Installation instructions Receivers IM-PN-RX0-A0-EN Language: English (original) PN-R5- PN-R5-2 PN-R5- PN-R5-4 CONTENTS Chapter : CUSTOMER INFORMATION Chapter 2: FUNCTIONAL SAFETY 6 Chapter : PRODUCT
More informationReceiver Type /Version Factory No. Frequency. Transmitter Type /Version Factory No. Frequency
Receiver Type /Version Factory No. Frequency Transmitter Type /Version Factory No. Frequency 1. STANDARD SPECIFICATION Portable transmitter. Receiver with integrated mounting holes. Multi-pin connecting
More informationD.C. BRUSHLESS MOTORS DRIVE. BLD07-IT Service Manual
D.C. BRUSHLESS MOTORS DRIVE BLD07-IT Service Manual INTECNO s.r.l. Via Caduti di Sabbiuno n. 9/E 40011 Anzola Emilia (BO) - Italy tel. 051.19985350 fax 051.19985360 www.intecno-srl.com INDEX Description
More informationS-COR. FIGURE 1 Wiring Diagram NOTE: To reset S-COR to factory settings, press and! hold < and > buttons upon power up. INSTALLATION INSTRUCTIONS
Section 1 General Description The ClearPath Spectrum Wireless System is comprised of two devices; a Coordinator () that functions in a similar role as traditional wireless system receivers, and a Transceiver
More informationERV-M ELECTRONIC FAN SPEED CONTROLLER. Mounting and operating instructions
ELECTRONIC FAN SPEED CONTROLLER Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5
More informationGENERIC 7SW. User Installation / Configuration Manual. T150 Transmitter R170 Receiver. June 15, Version 1 DMAN - XXXX-XX
GENERIC 7SW User Installation / Configuration Manual T150 Transmitter R170 Receiver June 15, 2006 Version 1 DMAN - XXXX-XX #74-1833 Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604) 944-9247
More informationMicromate User Manual
Microcoin Table of Contents Page Essential Information 2 1.0 Connection and Configuration 3 1.1 Connection 3 1.2 Switch On 4 1.3 Configuration for Use 4 2.0 Check the Configuration of a Validator 5 2.1
More informationET Water SmartWorks Panel Installation Guide
ET Water SmartWorks Panel Installation Guide You are installing a new piece of equipment that retrofits into an existing irrigation controller in order to create a weather-based irrigation control system.
More informationInstallation and operating instructions manual
RADIOSAFE Series Wireless emergency stop system UDF RSRA URE SCI-B Installation and operating instructions manual - TRANSLATED IN ENGLISH FROM ORIGINAL FRENCH VERSION - Page 1 / 41 TABLE OF CONTENTS 1
More informationGENERIC. User Installation / Configuration Manual. T300 Transmitter R170 Receiver. Revised May 23, Version 4 DMAN
GENERIC User Installation / Configuration Manual T300 Transmitter R170 Receiver Revised May 23, 2006 Version 4 DMAN - 2866-01 #74-1833 Coast Meridian Road, Port Coquitlam, BC, Canada V3C 6G5 Ph# (604)
More informationV Pg. M1: V, V, V Pg. M1 R1: Relay 1 Pg. M1 R2: Relay 2 (three-phase only) output status output status KW Pg. M2:,, Pg. M2n: neutral Pg. M3: P1, P2, P
Via Vizzano 44-40044 Pontecchio Marconi (Bologna)Italy Tel. +39 051 6782006 - Fax +39 051 845544 http://www.elcontrol-energy.net - e-mail: Italia vendite@elcontrol-energy.net estero: sales@elcontrol-energy.net
More informationThe system (EF-7700) consists out of two parts: the transmitter (EF-7602) and the receiver including wiring (EF-7701).
PRODUCT DESCRIPTION IMPORTANT! In order to get the best out of your system it is important you take the time to read through the manual before you start to install/program your equipment. The system (EF-7700)
More informationEnrange Pre-engineered MLTX Transmitter
Enrange Pre-engineered MLTX Transmitter Wireless Controls Part Number: 198-50002-1000-R1 Copyright 2011 Magnetek Material Handling Your New Radio Remote Thank you for your purchase of Magnetek s Enrange
More informationFCC ID: AXI IC: 10239A Alignment
Introduction The VX-261 is carefully aligned at the factory for the specified performance across the frequency range specified for each version. Realignment should therefore not be necessary except in
More informationIMPORTANT! Please take the time to read through the manual before you start to install/program your equipment.
PRODUCT DESCRIPTION IMPORTANT! Please take the time to read through the manual before you start to install/program your equipment. The systems KRC11, 12, 13 and 14 consists of two parts: the transmitter
More informationPMR446 Radio Instruction Manual
Tectalk PRO PMR446 Radio Instruction Manual Thank you for purchasing this radio. All our products are built to offer excellent value by combining advanced features, great design and manufacturing quality.
More informationUSER MANUAL Table of Contents
USER MANUAL Table of Contents Safety Information 3 Specifications 4 Main Power Connection 5 DMX-512 Connection 5 Fixture Level 6 Set Up 6 Operation Options 7 Connection 8 Rigging the Fixture 9 Cleaning
More informationU S E R S M A N U A L
U S E R S M A N U A L T H E R M O R E G U L A T O R T R 5 0 0 / T R 5 0 1 S E R I E S HUNDREDTHS VERSION ENGLISH V.1.2 TABLE OF CONTENTS -1- Introduction... page 2-2- Technical specifications -3- Description
More informationInstallation instructions
Installation instructions T70RX-03AIB, T70RX-03AWB, T70TX-02TTB, T70TX-03STB, T70TX-06TTB LANGUAGE: English (original) IM-T70-RX001-A01-EN CONTENTS Chapter 1: CUSTOMER INFORMATION 3 Chapter 2: PRODUCT
More informationGROUP OF COMPANIES. MERLIN STEALTH Electric Fence Energizer INSTALLERS MANUAL
GROUP OF COMPANIES MERLIN STEALTH Electric Fence Energizer INSTALLERS MANUAL Revision 1.5 23 February 2007 : INSTALLERS MANUAL Table of Contents 2 INTRODUCTION.. 3 INSTALLER OPTIONS...... 4-11 ALARM SETTING
More informationXtreme Power Systems
Xtreme Power Systems XtremeLink NANO RECEIVER Installation And Usage Manual XtremeLink is a registered trademark of Xtreme Power Systems, LLC. Firmware v 1.9 Manual v 1.9 Revision Date: November 11 th,
More informationBlue Point Engineering
lue Point Engineering Wizard - I Interface oard http://www.pesolutions.com (303) 651.3794 Pointing the Way to Solutions! Talking / Eye Moving Skull Connectors pplication Examples 7805 Eyeball Jar nimatronic
More informationElectric Crane Proportional Remote (3203i-6000i) USA
Manual Part # 99905683 Electric Crane Proportional Remote (3203i-6000i) USA Revised 20090826 IOWA MOLD TOOLING CO., INC. PO Box 189 Garner, IA 50438 Tel: 641-923-3711 FAX: 641-923-2424 Website: http://www.imt.com
More informationSUPER TRAINER Micro-iDT SERIES
TM SUPER TRAINER Micro-iDT SERIES Electronic Dog Trainer Owner s Manual Micro-iDT Z3000 (One Dog Trainer) Micro-iDT Z3002 (Two Dog Trainer) Micro-iDT Z3003 (Three Dog Trainer) 2 TABLE OF CONTENTS Table
More informationUser Manual. ProRF Encoder Transmitter & Receiver
User Manual ProRF Encoder Transmitter & Receiver WARRANTY Accurate Technology, Inc. warrants the ProScale Systems against defective parts and workmanship for 1 year commencing from the date of original
More informationRosemount 753R Remote Web Based Monitoring Indicator
Rosemount 753R Remote Web Based Monitoring Indicator Product Discontinued February 2010 Start Overview Rosemount 753R with Integral 3051S Pressure Transmitter Rosemount 753R with Remote Mounted HART Transmitter
More informationRSMFX-2R MULTIFUNCTIONAL
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 4 OPERATIONAL DIAGRAMS 5 WIRING AND
More informationRMV25 / RMV50 RMU25 / RMU45
RMV25 / RMV50 RMU25 / RMU45 Owner's Manual TABLE OF CONTENTS INTRODUCTION... 3 FCC Requirements... 3 SAFETY WARNING INFORMATION... 3 CONTROLS and INDICATORS... 5 FRONT PANEL... 5 LCD Icons and Indicators...
More informationHB-25 Motor Controller (#29144)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationInstallation and user s guide H A. NCi-5 non-contact tool setting interface
Installation and user s guide H-5259-8500-05-A NCi-5 non-contact tool setting interface 1 English Installation and user s guide NCi-5 non-contact tool setting interface This page is intentionally left
More informationQuick Start Guide. Antenna Alignment Tool AIMWLLR0-35. QSG rev 7 AIMWLLR0-35 [NRB-0200] QSG.indd 1
Quick Start Guide Antenna Alignment Tool AIMWLLR0-35 QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.indd 1 Welcome This quick start guide is designed to familiarize you with the features and use of the NetComm
More informationBlue Point Engineering
Overview Blue Point Instruction Board 2-CH Boards, Terminal Block and Ribbon Cable I Type: RF Radio (315 MHz) 1-2 Channels (FCC Part 15 Compliant Components). Operating Voltage: 6-15 VDC @ 1 Amp (Wall
More informationIMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Model: RB-G-K10 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver system is intended to provide
More informationADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W
ADC5000 SERIES AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications 60W, 125W and 250 W Input voltage 230/115 VAC voltages 12, 24, 36 or 48 VDC Statistical MTBF >3 000
More informationInstallation Instructions
Installation Instructions Garage Door Opener Radio Controls Model 5010 (300 mhz) \ 5012 (310 mhz) Single Button Transmitters Model 5100-01 (300 mhz) \ 5102-01 (310 mhz) Receivers WARNING: Disconnect operator
More informationALACHUA ARES SIMPLEX REPEATER STATION INSTRUCTION MANUAL VERSION 1.0 MARCH
ALACHUA ARES SIMPLEX REPEATER STATION INSTRUCTION MANUAL VERSION 1.0 MARCH 23 2017 1 INTRODUCTION A simplex repeater is nothing more than a digital tape recorder that listens to an FM simplex transceiver,
More informationR PROFLAME Instruction Book Collection
9.956.028 R00 584 PROFLAME Instruction Book Collection 4-17 18-29 584 PROFLAME System 30-39 Appendix: DIP SWITCH NUMBER (0=ON 1=OFF) 40-41 4-17 Fig. 1 The SIT is a device that allows, in conjunction with
More informationCAN-2. Enrange Radio Receiver. September 2013 Part Number: R3 Copyright 2013 Magnetek Material Handling
CAN-2 Enrange Radio Receiver Part Number: 198-80100-0001 R3 Copyright 2013 Magnetek Material Handling Your New Radio Receiver Thank you for your purchase of Magnetek s Enrange TM CAN-2 Radio Receiver.
More informationVIKING VX UHF LTR 25W-110W Repeater
VIKING VX UHF LTR 25W-110W Repeater Part No. 242-20X4-213 Second Printing 1-00mwp Printed in U.S.A. 1-1 October 1995 Part No. 001-2008-202 October 1995 Part No. 001-2008-202 1-2 Copyright 1997 by the E.F.
More informationOperating Manual. isolate501
Operating Manual isolate501 Document Number 413569 (See Last Page for Revision Details). Copyright Extronics Ltd, 2015 Page 2 of 21 Contents 1 Introduction... 4 2 Safety Information and Notes... 5 2.1
More informationPage 1 of 6 Page 1 of 12 Yaesu FT-5100/FT-5200 MODS Rev B (14 Apr 1993) This is a collection of hardware and software mods for the Yaesu 5100/5200 pair. I have the 5100, so I can't verify these for the
More informationHeadset Intercom System. Operating Instructions
Headset Intercom System Model C1025 Operating Instructions Headset and Transceiver Pack Base Station Model C1025 Table of Contents Intended Use...iii FCC Information...iii Service...iii System Descriptions...1
More informationCPAT AFDD Operation Manual
CPAT AFDD Operation Manual v 2.0 / 2008.08.12 Contents 1. FCC and IC Compliance Statements 3 2. System Components 4 3. AFDD Unit Physical Installation 5 4. Antennas Installation 6 5. Electrical Installation
More informationPULSE TRANSDUCER K816 / IWe2. Operating Instructions
PULSE TRNSDUCER K816 / IWe2 Operating Instructions Operating Instructions s per: 10/10/2003 Copyright by FTL 2001-2003 K816_IWe2_Bed_2003-1010_engl.doc GENERL INFORMTION With this two-stage transducer
More informationPRODUCT MANUAL VHF & UHF Pocket Paging Transmitter. Version 1.00 April 2017
11-85-0000 VHF & UHF Pocket Paging Transmitter PRODUCT MANUAL Version 1.00 April 2017 Copyright 2017 Sea Air and Land Communications Ltd. All rights reserved. P a g e 1 Salcom Product Documentation This
More informationDTMF decoder kit with 8 outputs and Morse transpond. 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs
DJS Electronics Ltd cstech.co.uk DTMF decoder kit with 8 outputs and Morse transpond Features 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs Each output can be
More informationM2 Antenna Systems, Inc. Model No: S3 Sequencer. Operating Instructions
WARRANTY ADDENDUM TROUBLESHOOTING INSTALLATION OVERVIEW M2 Antenna Systems, Inc. Model No: S3 Sequencer Operating Instructions PLEASE READ BEFORE USE AND SAVE M2 Antenna Systems, Inc. 4402 N. Selland Ave.
More informationLPTDX CHANNEL DIMMER PACK
12-CHANNEL DIMMER PACK 1. Introduction To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of
More informationChapter 9: Troubleshooting
AFC1500 Operations Manual Chapter 9: Troubleshooting (Rev. 6: 10/09) Chapter 9: Troubleshooting Page 9-1 Chapter 9: Troubleshooting 9.1 Abnormal Conditions. When an abnormal condition is detected by the
More informationINSTALLATION AND OPERATING MANUAL
INSTALLATION AND OPERATING MANUAL FOR RBDA-PCS-1/25W-90-A INDOOR REPEATER TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW 3 BDA BLOCK DIAGRAM DESCRIPTION 3 FCC INFORMATION FOR USER 3 BDA BLOCK DIAGRAM
More informationFlex EX2. Radio Control Equipment (CE) Quick Reference Manual. Part Number: M000C R00 May 2018 Copyright 2018 Magnetek Material Handling
Flex EX2 Radio Control Equipment (CE) Quick Reference Manual Part Number: 191-50000-M000C R00 Copyright 2018 Magnetek Material Handling Table of Contents Service Information...3 Your New Radio Remote Control
More informationGUIDE SPECIFICATIONS CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP GENERAL DESCRIPTION
GUIDE SPECIFICATIONS 256920-UGS-A-0506 Simplicity Intelli-Comfort Optional Control in 3-25 Ton Packaged Units GENERAL DESCRIPTION CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP Equipment with Simplicity
More information802.11n, 2.4G 1T1R Wireless LAN PCI Express Half Mini Card
802.11n, 2.4G 1T1R Wireless LAN PCI Express Half Mini Card WN6605LH Realtek RTL8191SE User s Manual Ben J. Chen 3/4/2010 Federal Communication Commission Interference Statement This equipment has been
More informationCRUX II/BTGPS USER GUIDE. Model:D1598
CRUX II/BTGPS USER GUIDE Model:D1598 0 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
More informationDTR Frequently Asked Questions (FAQ) LEAFLET
DIGITAL TWO-WAY RADIO DTR Frequently Asked Questions (FAQ) LEAFLET April 2019 2019 Motorola Solutions, Inc. All rights reserved. *MN005512A01* MN005512A01-AA Contents Product Safety and RF Exposure Compliance...3
More informationField Hub Installation Guide. P/N Rev. C 05/15
Field Hub Installation Guide P/N016-0171-380 Rev. C 05/15 E21714 Copyright 2015 Disclaimer While every effort has been made to ensure the accuracy of this document, Raven Industries assumes no responsibility
More informationMODEL: Duo Product id:duomk214f Duo OWNER S MANUAL
MODEL: Product id:duomk214f OWNER S MANUAL Introduction We thank you for purchasing our amplifiers. Your decision to be part of something different is what we strive for. Our products reflects who we are,
More informationEnrange Engineered MLTX Transmitter
Enrange Engineered MLTX Transmitter Wireless Controls Instruction Manual Part Number: 198-50002-100-R1 Copyright 2011 Magnetek Material Handling Your New Radio Remote Thank you for your purchase of Magnetek
More information