General Specifications

Transcription

1 General Specifications GS 1E2C1-1E AXFA11G Magnetic Flowmeter Remote Converter The AXFA11 magnetic flowmeter high grade remote converter is a sophisticated product with outstanding reliability and ease of operation, developed on the basis of decades of field-proven experience. The AXFA11 employs an LCD indicar, infra-red switches, and Easy Setup parameters ensure substantially improved ease of maintenance. The combination of a replaceable electrode type flowtube and diagnostics detect the adhesion level on the electrodes dramatically improves maintainability. The AXFA11 also employs the fluid noise free Dual Frequency Excitation Method and the newly added Enhanced Dual Frequency Excitation Method as an option for more difficult applications ensure greater stability and quicker response. Note: The Dual Frequency Excitation Method is Yokogawa s unique technology. FEATURES User-oriented Functionality Fluid Adhesion Level Diagnosis By constantly moniring the level of insulating substance on the electrodes, it is possible determine when maintenance is required. With the utilization of an optional replaceable electrode type flowtube, in cases of severe adhesion, the electrodes can be easily removed from the flowmeter and cleaned. Clear and Versatile Indications The LCD indicar employs a large, backlit full dotmatrix, that can facilitate various displays. One three lines are available. When there is an alarm condition, a full description of the countermeasure is indicated. Easy Setup Parameters The most frequently used parameters are arranged in a group at the p. The infra-red switches enable the users set parameters without opening the cover. Operation Immediately after Installation The AXFA11 is shipped with the main parameters completely set. Therefore, the AXFA11 can be operated immediately after installation and wiring. Compact and Light-weight Amplifier The AXFA11 is equipped with a compact and lightweight amplifier. Expansion of Product Lineup Improve Accuracy Specification The standard accuracy is.35% of reading. Also available is an optional high accuracy calibration rated at.2% of reading. Enhanced Performance and Specifications Enhanced Dual Frequency Excitation Method The Enhanced Dual Frequency Excitation Method can be optionally selected. For difficult applications such as for high concentration slurries or low conductivity fluid, extremely stable measurements can be realized. Improved Minimum Conductivity The newly designed AXF converter permits the measurement of fluids with conductivity as low as 1µS/cm. High-Speed Pulse Output The pulse rate now goes up 1, pps (pulse/ second) for use with high speed applications such as in short time batch processes. Versatile Input/ouput Function Now Available The functions of one current output, one pulse output, one alarm output, two status inputs, and two status outputs are available. CONTENTS Features P. 1 Standard Specifications P. 2 Standard Performance P. 4 Normal Operating Conditions P. 5 Accessories P. 5 Model and Suffix Code P. 6 Optional Specifications for AXFA11 Remote Converter P. 7 Terminal Configuration, Terminal Wiring P. 7 External Dimensions P. 8 Ordering Information P.1 Yokogawa Electric Corporation Nakacho, Musashino-shi, Tokyo 18, Japan Tel.: Fax.: GS 1E2C1-1E Copyright June 23 7th Edition Nov. 29

2 STANDARD SPECIFICATIONS Excitation Method: (Combined with AXF Remote Flowtube) Standard dual frequency excitation: Size mm (.1 16 in.) Enhanced dual frequency excitation: Size 25 2 mm (1. 8. in.) (Optional code HF1 or HF2) Pulsed DC excitation: Size 5 26 mm (2 14 in.) Input Signal: Two Status Inputs: Dry contact Load resistance: 2 or less (ON), 1 kω or more (OFF) Output Signals: One Current Output: 4 2 ma DC (load resistance: 1kΩ maximum, including cable resistance) One Pulse Output: Transisr contact output (open collecr) Contact capacity: 3 V DC (OFF), 2 ma (ON) Output rate:.1 1, pps (pulse/second) One Alarm Output: Transisr contact output (open collecr) Contact capacity: 3 V DC (OFF), 2 ma (ON) Two Status Outputs: Transisr contact output (open collecr) Contact capacity: 3 V DC (OFF), 2 ma (ON) Communication Signals: BRAIN or HART communication signal (Superimposed on the 4 2 ma DC signal) Distance from Power Line: 15 cm (6 in.) or more (Parallel wiring should be avoided.) BRAIN: Communication Distance: Up 1.5 km (.93 miles), when polyethylene insulated PVC-sheathed cables (CEV cables) are used. Communication distance varies depending on the type of cable and wiring used. Load Resistance: Ω (including cable resistance) Load Capacitance:.22 µf or less Load Inductance: 3.3 mh or less Input Impedance of Communicating Device: 1 kω or more (at 2.4 khz) HART: Load Resistance: 25 6 Ω (including cable resistance) Note: HART is a registered trademark of the HART Communication Foundation. 2 Data Security During Power Failure: Data (parameters, talizer value, etc.) srage by EEPROM. No back-up battery required. Indicar: Full dot-matrix LCD ( pixels) Lightning Protecr: The lightning protecr is built in the excitation current output, the current output, the signal common, and the pulse/alarm/status input and output terminals. When optional code A is selected, the lightning protecr is built in the power terminals. Protection: IP66, IP67, JIS C92 immersion-proof type Coating: Case and Cover: Corrosion-resistant coating Coating Color; Silver gray (Munsell 3.2PB 7.4/1.2 or its equivalent) Cover Mounting Screws: Polyurethane corrosion-resistant Coating Color: Mint green (Munsell 5.6BG 3.3/2.9 or its equivalent) Converter Material: Case and Cover: Aluminum alloy Mounting/Shapes: Mounting: 2-inch pipe, panel or surface mounting Electrical Connection: ANSI 1/2 NPT female ISO M2 1.5 female JIS G1/2 (PF1/2) female Terminal Connection: M4 size screw terminal Grounding: Grounding resistance 1 Ω or less When optional code A is selected, grounding resistance 1 Ω or less shall be applied. Combined Remote Flowtube: AXFA11 Converter can be combined with size mm (.1 14 in.) of AXF Remote Flowtube. However, the AXFA11 converter cannot combine with AXF Remote Flowtube of TIIS flame proof type (In this case, use the AXFA14 converter). If a combined converter is changed from AXFA11 AXFA14 or vice versa, a new meter facr must be adjusted by flow calibrations.

3 Functions How Set Parameters: The indicar s LCD and three infra-red switches enable users set parameters without opening the case cover. Parameters can also be set by means of the HHT(Handheld terminal). Displayed Languages: Users can choose a language from among English, Japanese, German, French, Italian, Spanish. Instantaneous Flow Rate/Totalized Value Display Functions: The full dot-matrix LCD enables user selections of displays from one line three lines for: Instantaneous flow rate Instantaneous flow rate (%) Instantaneous flow rate (bar graph) Current output value (ma) Totalized forward-direction flow rate Totalized reverse-direction flow rate Totalized differential flow rate Tag No. Results of electrode adhesion diagnostics Communication type Totalizer Display Function: The flow rate is counted one pulse at a time according the setting of talization pulse weights. For forward and reverse flow measurement functions, the talized values of the flow direction (forward or reverse) and the flow direction are displayed on the indicar gether with the units. The difference of talized values between the forward and reverse flow rate can be displayed. Totalization for the reverse flow rate is carried out only when Forward and reverse flow measurement functions is selected. Damping Time Constant: Time constant can be set from.1 second 2. seconds (63% response). Span Setting Function: Span flows can be set in units such as volume flow rate, mass flow rate, time, or flow rate value. The velocity unit can also be set. Volume Flow Rate Unit: kcf, cf, mcf, Mgal (US), kgal (US), gal (US), mgal (US), kbbl (US)*, bbl (US)*, mbbl (US)*, µbbl (US)*, Ml (megaliter), m 3, kl (kiloliter), l (liter), cm 3 Mass Flow Rate Unit (Density must be set.): klb (US), lb (US), t (n), kg, g Velocity Unit: ft, m (meter) Time Unit: s (sec), min, h (hour), d (day) * US Oil or US Beer can be selected. Pulse Output: Scaled pulse can be output by setting a pulse weight. Pulse Width:Duty 5% or fixed pulse width (.5,.1,.5, 1, 2, 33, 5, 1 ms) can be selected. Output Rate:.1 1, pps (pulse/second) 3 Multi-range Function: Range switching via status input Status input enables the switching of up four ranges. Aumatic range switching When the flow rate exceeds 1 % of the range, transition the next range (up four ranges) is carried out aumatically. Range switching can be confirmed by status outputs and indicar. Forward and Reverse Flow Measurement Functions: Flows in both forward and reverse directions can be measured. The reverse flow measurement can be confirmed by status output and indicar. Totalization Switch: The status output is carried out when a talized value becomes equal or greater than the set value. Preset Totalization: The parameter setting or status input enables a talized value be preset a setting value or zero. % Signal Lock: Status input forcibly fixes the instantaneous flow rate display, current output, pulse output, and flow rate talization %. Alarm Selection Function: Alarms are classified in System Alarms (hard failures), Process Alarms (such as Empty Pipe, Signal Overflow and Adhesion Alarm ), Setting Alarms, and Warnings. Whether alarms should be generated or not can be selected for each item. The current output generated for an alarm can be selected from among 2.4 ma or less, fixed 4 ma, 21.6 ma or more, or HOLD. Alarm Output: Alarms are generated only for the items selected via the Alarm Selection Function if relevant failures occur. Self Diagnostics Functions: If alarms are generated, details of the System Alarms, Process Alarms, Setting Alarms and Warnings are displayed gether with concrete descriptions of countermeasures. Flow Upper/Lower Limit Alarms: If a flow rate becomes greater or smaller than the set value, this alarm is generated. In addition, two upper limits (H, HH) and two lower limits (L, LL) can be set. If a flow rate becomes greater or smaller than any of the set values, the status is output. Electrode Adhesion Diagnostics Function: This function enables moniring of the adhesion level of insulating substances the electrodes. Depending on the status of adhesion, users are notified by a warning or an alarm via status outputs. If replaceable electrodes are used, they can be removed and cleaned when adhesion occurs.

4 STANDARD PERFORMANCE Accuracy (Combined with AXF Remote Flowtube) Note: The accuracy of a product before shipment is defined as talized value at the result of calibration test in our water actual flow test facility. Calibrated conditions in our water actual test facility are as follows: Fluid temperature; 2 ± 1 C Ambient temperature; 2 ± 5 C Length of straight runs;1 D or more on the upstream side; 5 D or more on the downstream side Reference conditions; Similar BS EN2914 (1993); ISO 914 (1991) Pulse Output: PFA/Ceramics Lining: Size mm (in.) 2.5 (.1) 15 (.5) 25 (1.) 2 (8.) 25 (1) 4 (16) Flow Velocity V m/s (ft/s) V.3 (1).3 V 1 (1) (33) V.15 (.5).15 V 1 (.5) (33) V.15 (.5).15 V 1 (.5) (33) Standard Accuracy (Calibration code B) 1. mm/s.35% of Rate.5 mm/s.35% of Rate.5 mm/s.35% of Rate Flow Velocity V m/s (ft/s) V.15 (.5).5 mm/s.15 V 1.18 (.5) (3.3).2mm/s 1 V 1 (3.3) (33) Enhanced dual frequency excitation (Option code HF2) : Standard accuracy 1 mm/ s Size 2.5 mm (.1 in.) 15 mm (.5 in.) Pulse Output Accuracy High Standard grade Accuracy High grade Accuracy (Calibration code C) Size 25 mm (1. in.) 4 mm (16 in.) Pulse Output Accuracy Standard Accuracy High grade Accuracy F1.EPS F2.EPS T1.EPS Polyurethane Rubber/Natural Soft Rubber/EPDM Rubber Lining Size mm (in.) 25 (1.) 4 (16) 5 (2) 1 (4) 11 (44) 2 (8) 22 (88) 26 (14) Flow Velocity V m/s (ft/s) Standard Accuracy (Calibration code B) V.3 (1.) 1. mm/s.3 V 1 (1.) (33).35 V.3 (1.) 1.75 mm/s.3 V 1 (1.) (3.3) 1 V 1 (3.3) (33).25 1 mm/s.35 V.3 (1.) 2.2 mm/s.3 V 1 (1.) (3.3).4 1 mm/s 1 V 1 (3.3) (33).5 V 1 (3.3) 1 V 1 (3.3) (33) 8.5 mm/s.85 T2.EPS Enhanced dual frequency excitation (Option code HF2) : Standard accuracy 1 mm/ s Size 25 mm (1. in.) 4 mm (16 in.) Pulse Output Accuracy High Standard grade Accuracy F1.EPS Size 5 mm (2 in.) 1 mm (4 in.) Pulse.6 Output Accuracy High Standard grade Accuracy F16-1.EPS Size 11 mm (44 in.) 2 mm (8 in.) Pulse.6 Output.5 Accuracy.4.2 High Standard grade Accuracy F16-2.EPS 4

5 Size 22 mm (88 in.) 26 mm (14 in.) Pulse 1.2 Output Accuracy High Standard grade Accuracy F16-3.EPS Current Output: Pulse output accuracy plus.5% of Span Repeatability:.1 (V 1 m/s (3.3 ft/s)).5.5 mm/s (V < 1 m/s (3.3 ft/s)) Maximum Power Consumption: Combined with AXF Remote Flowtube: 2 W Insulation Resistance(*1) : Between power supply terminals and ground terminal: 1MΩ at 5V DC Between power supply terminals and input/output/ excitation current terminals : 1MΩ at 5V DC Between ground terminal and input/output/excitation current terminals: 2MΩ at 1V DC Between input/output/excitation current terminal: 2MΩ at 1V DC Withstand Voltage(*1) : Between power supply terminals and ground terminal: 139V AC for 2 seconds Between power supply terminals and input/output terminals: 139V AC for 2 seconds Between excitation current terminal and ground terminal: 16V AC for 2 seconds Between excitation current terminal and input /output terminals: 2V AC for 2 seconds CAUTION *1: When performing the Insulation Resistance Test or the Withstand Voltage Test, please obey the following caution. Following the relevant test, wait for more than 1 seconds after the power supply has been turned off before removing the cover. Remove all wires from terminals before testing. When the power terminal has a lighting protecr (optional code A), remove the short bar at the ground terminal. After testing, be sure discharge by using a resistance and return all wires and the short bar its correct position. Screws must be tightened a rque of 1.18 N-m or more. After closing the cover, the power supply can be resred. Safety Requirement Standards: EN611-1 Altitude at installation site: Max. 2 m above sea level Installation category based on IEC11: Overvoltage category II ( II applies electrical equipment which is supplied from a fixed installation-like distribution board.) Pollution degree based on IEC11 Pollution degree 2 ( Pollution degree describes the degree which a solid, liquid, or gas which deteriorates dielectric strength or surface resistivity is adhering. 2 applies a normal indoor atmosphere.) EMC Conformity Standards:, EN Class A, Table 2 (For use in industrial locations) EN EN Class A EN NORMAL OPERATING CONDITIONS Ambient Temperature: 4 C +6 C ( 4 F +14 F) Indicar s operating range: 2 C +6 C ( 4 F +14 F) Ambient Humidity: 1% Lengthy continuous operation at 95% or more is not recommended. Power Supply: Power supply code 1: AC specifications Rated power supply: 1 24 V AC, 5/6 Hz (Operating voltage range: V AC) DC specifications Rated power supply: 1 12 V DC (Operating voltage range: 9 13 V DC) Power supply code 2: AC specifications Rated power supply: 24 V AC, 5/6 Hz (Operating voltage range: V AC) DC specifications Rated power supply: 24 V DC (Operating voltage range: V DC) Allowable cable length m(ft) 42 (138) 28 ( 92) 2 ( 66) 1 ( 33) Supplied Power and Cable Length for Power Supply Code Usable range E (V) Cable cross section area: 1.25 mm 2 Cable cross section area: 2 mm 2 Vibration Conditions: Level of vibration in conformity with IEC (SAMA ) 4.9 m/s 2 or less (frequency of 5 Hz or less) Note: Avoid locations with much vibration (with a vibration frequency of 5 Hz or more), which may cause damage the equipment. F.EPS 5

6 ACCESSORIES Fuse (Time lag fuse): 1 pc. Power supply code 1; T2.5 A, 25 V Power supply code 2; T3.15A, 25 V Mounting bracket: 1 set MODEL AND SUFFIX CODE AXFA11 Magnetic Flowmeter Remote Converter: Model Suffix Code Description AXFA11 Magnetic Flowmeter Remote Converter General-Purpose Use Use G For AXF Remote Flowtube of size mm (.1 in. 14 in.) Output Signal and Communication Power Supply Electrical Connections Indicar Option -D -E ma DC, BRAIN Communication 4 2 ma DC, HART Communication 1 V 24 V AC or 1 12 V DC 24 V AC/DC (*1) JIS G1/2 female ANSI 1/2 NPT female ISO M2 1.5 female 1 With Indicar / Optional code (See the Table of Optional Specifications) *1: In case of power supply code 2 (24 V AC/DC), optional code A (lighting protecr) is mandary. T3.EPS Recommended Excitation, Power and Output Cable: Use Polyvinyl chloride insulated and sheathed control cable (JIS C341) or Polyvinyl chloride insulated and sheathed portable power cables (JIS C3312) or equivalents. Outer Diameter: mm ( in.) mm (.3.47 in.) for optional code EG, EU and EW 6 12 mm ( in.) for optional code EP Nominal Cross Section(single wire): mm 2 Nominal Cross Section(standard wire): mm 2 6 Signal Cable: Model Suffix Code Description AXFC Termination Cable Length Option L /C Magnetic Flowmeter Dedicated Signal cable for the ADMAG AXF series No Termination. A set of termination parts for M4 screws is attached. Terminated for the AXFA11/14 Converter. Designate the cable length, unit: m Following L, specify the cable in three digits as multiple of 1 meter (e.g., 1, 2, or 5) for a length up 5 m, or as a multiple of 5 meters (i.e., 5, 1, 15, or the like). The maximum cable length: 2 m for combined use with AXFA11 1 m for combined use with AXFA14 With termination parts sets. Following C, specify the q ty of sets of termination parts in one digits. T4.EPS Note: The cable is constructed with double shielding over the two conducrs, and uses heat-resistant vinyl as the outer covering material. Finished diameter: 1.5 mm (.413 in.) Maximum temperature: +8 C (+176 F) Unnecessary order the above cable for submersible type flowtube or for the optional code DHC flowtube because the flowtube is wired with 3 m (98 ft) cable. For excitation cable, prepare a two-core cable at the cusmer side.

7 7 OPTIONAL SPECIFICATIONS FOR AXFA11 REMOTE CONVERTER Item Specification Code Lightning Protecr DC Noise Cut Circuit Burn Out Down NAMUR NE43 Compliance Active Pulse Output G3/4 Female Waterproof Glands Waterproof Glands Waterproof Glands with Union Joints Plastic Glands Air Purge Fitting Stainless Steel Mounting Bracket AM11 Replacement Bracket Stainless Steel Tag Plate Painting Color Change Epoxy Resin Coating High Anti-corrosion Coating Calibration Certificate A lightning protecr is built in the power terminals. In case of power supply code 2 (24 V AC/DC), this optional code is mandary. The DC Noise Cut Circuit is built in. Available for 15 mm (.5 in.) and larger sizes, and for fluids with the conductivity of 5 µs/cm or higher. Nullifies the empty check and electrode adhesion diagnostics function. The output level is set ma during a CPU failure and is set 2.4 ma (-1%) or less during an alarm. Standard products are delivered with a setting 25 ma during a CPU failure and 21.6 ma (11%) or more during an alarm. Output signal limits: ma Failure alarm down-scale: The output level is set ma during a CPU failure and is set 2.4 ma ( 1%) or less during an alarm. Failure alarm up-scale. The output level is set 25 ma during a CPU failure and is set 21.6 ma (11%) or more during an alarm. Active pulses are output in order drive an external electromagnetic or electronic counter directly using the converter s internal power supply. (Nullfies the standard transisr contact pulse output.) Output voltage: 24 V DC ±2% Pulse specifications: The drive current of 3 15 ma Pulse rate:.1 2 pps (pulse/second); Pulse width: 2, 33, 5, or 1 ms Waterproof glands for G3/4 conduits or flexible tubes are attached the electrical connections. Available only for JIS G1/2 female electric connections. Waterproof glands are attached the electrical connections. Available only for JIS G1/2 female electric connections. Waterproof glands with union joints are attached the electrical connections. Available only for JIS G1/2 electric connections. Plastic glands are attached the electrical connections. Available only for JIS G1/2 female electric connections. Provided with an air purge fitting (1.5 L/min air consumption) with purge air pressure at.14 MPa or less. 1/4 NPT female (when electrical conn. code is 2 or 4) or Rc1/4 (PT 1/4) female (when electrical conn. code is ). Provided with a JIS SUS34 (AISI 34 SS/EN equivalent) stainless steel mounting bracket in lieu of the standard carbon steel bracket. Provided with a special mounting bracket for replacing an AM11 converter with an AXFA11. Screwed JIS SUS34 (AISI 34 SS/EN equivalent) stainless steel tag plate. Choose this option when an SS tag plate is required in addition the standard nameplate with the tag number inscribed on it. Dimension (Height Width): Appr (4.92) 4 (15.7) mm (inch) Coated in black (Munsell N1.5 or its equivalent.) Coated in jade green (Munsell 7.5BG4/1.5 or its equivalent.) Coated in metallic silver. Epoxy resin coating which has alkali-resistance instead of standard polyurethane resin coating. The color is same as standard type. Three-layer coating (polyurethane coating on two-layer epoxy resin coating) in the same range as that for the standard coating. The color is same as standard type. Salt/alkali/acid/weather- Level 2: The Declaration and the Calibration Equipment List are issued. Level 3: The Declaration and the Primary Standard List are issued. Level 4: The Declaration and the Yokogawa Measuring Instruments Control System are issued. A ELC C1 C2 C3 EM EW EG EU EP APC SB RK SCT P1 P2 P7 X1 X2 L2 L3 L4 T5.EPS Terminal Configuration I+ I CURRENT OUT SO1+ SO2+ COM STATUS OUT N/ L/+ POWER SUPPLY SHORT BAR EX1 EX2 EXCIT ATION AL+ AL C SA A B SB ALARM OUT SIGNAL P+ P SI1+ SI2+ COM PULSE OUT STATUS IN T6.EPS Terminal Wiring Terminal Symbols SIGNAL ALARM OUT STATUS OUT CURRENT OUT C SA A B SB AL+ AL- SO1+ SO2+ COM I+ I- Description Flow signal input Alarm output Status output (Two output) Current output 4 2mA DC Terminal Symbols STATUS IN PULSE OUT EXCITATION POWER SUPPLY Sl1+ Sl2+ COM P+ P- EX1 EX2 L /+ N/- Description Status input (Two input) Pulse output Excitation current output Power supply Functional grounding Protective grounding (Outside of the terminal) T7.EPS

8 8 EXTERNAL DIMENSIONS Remote Converter AXFA11G Pipe mounting 18(7.9) 4-ø6 Hole (Surface mounting hole) 12(4.72) Unit: mm (approx. inch) 65 (2.56) 21(8.27) 194(7.64) (1.22) (1.22) (1.22) (1.22) (67) (2.64) Panel mounting 1 1(.4.39) (Panel thickness) 1(3.94) Mounting Screw (M6 1(3.94)) 172(6.77) Panel cuut 23(7.99) 182(7.17) 15 (4.13) R3 MAX Surface mounting *1 Mounting Screw(M6) 18(.71) 65 (2.56) 24 (.94) (67) (2.64) 29 (1.14) 49 (1.93) Weight 3.3 kg (7.3 lb) *1: These screws must be provided by the user. 194(7.64) 62 (2.44) T8.EPS

9 9 Remote Converter AXFA11G /RK (AM11 Replacement Bracket) Pipe mounting 18(7.9) 4-ø6(.24) (Surface mounting hole) 133.5(5.26) (8.5) (3.17) 24 (.94) 29 (1.14) 65(2.56) 21(8.27) 194(7.64) (1.22) (1.22) (1.22) (1.22) 49 (1.93) (8.5) (3.17) Bracket for replacement (For pipe mounting) Surface mounting (19) (7.48) Mouting Screw *1 18(.71) (126.5) (4.98) *1: These screws must be * provided by the user. (62) (2.44) Bracket for replacement (For surface mounting) FFAXFA11E.EPS Unless otherwise specified, difference in the dimensions are refer the following table. Category of basic dimension Category of basic dimension Tolerance Above Equal or below Above Equal or below 3 (.12) 6 (.24) 1 (.39) 18 (.71) 3 (1.18) 5 (1.97) 8 (3.15) 12 (4.72) 18 (7.9) 25 (9.84) 315 (12.4) 4 (15.75) 3 (.12) 6 (.24) 1 (.39) 18 (.71) 3 (1.18) 5 (1.97) 8 (3.15) 12 (4.72) 18 (7.9) 25 (9.84) 315 (12.4) 4 (15.75) 5 (19.69) General lerance in the dimensional outline drawing..7 (.3).9 (.4) 1.1 (.4) 1.35 (.5) 1.65 (.6) 1.95 (.8) 2.3 (.9) 2.7 (.11) 3.15 (.12) 3.6 (.14) 4.5 (.16) 4.45 (.18) 4.85 (.19) 5 (19.69) 63 (24.8) 8 (31.5) 1 (39.37) 125 (49.21) 16 (62.99) 2 (78.74) 25 (98.43) Remarks: The numeric is based on criteria of lerance class IT18 in JIS B (24.8) 8 (31.5) 1 (39.37) 125 (49.21) 16 (62.99) 2 (78.74) 25 (98.43) 315 (124.2) Unit : mm (approx.inch) Tolerance 5.5 ( 2.17) 6.25 (.25) 7. (.28) 8.25 (.32) 9.75 (.38) 11.5 (.45) 14. (.55) 16.5 (.65)

10 1 Dedicated Signal Cable AXFC-4-L A 15 5 (5.91) 8(.31)Max (5.91) G 9(3.54) E B B 55(2.17) 9(3.54) F A Unit: mm (approx. inch) C SA SB C (WHITE) (BLACK) (RED) D (WHITE) (BLACK) (RED) 8(.31)Max. CONVERTER 2(.79) L(SPECIFIED LENGTH) AXFC ø1.5(.41) FLOW TUBE Model AXFC-4 D E F G 7(2.76) 25(.98) 5(1.97) 6(2.36) AXFC--L F4.EPS CAP ø1.5(.41) AXFC L(SPECIFIED LENGTH)+34(13.39)(LENGTH for END TREATMENT) F5.EPS ORDERING INFORMATION Note 1: When ordering in combination a remote flowtube and a remote converter, specify the flow span, unit, pulse weight, and talizer display pulse weight can be specified. These parameters will then be set in the combined converter before shipment. When ordering of a converter alone, these parameters cannot specify. Please refer GS1E2D1-1E ORDERING INFORMATION. Note 2: Some options, if ordered, require the relevant specifications be input when ordering. 1. Model, specification and option codes. 2. Tag number Each tag number can be specified in up 16 characters in a combination of letters (capital or small letters), numbers, - and.. For HART procol, up 8 characters can be specified. If specified, the tag number is inscribed on the product s name plate and tag plate (if optional code SCT is selected). The tag number is also set in the memory of converter. If the user wishes change only the tag number be set in a converter s memory, specify the software tag. If a tag number is not specified, the tag number is set as a blank. RELATED INSTRUMENTS Calibrar for Magnetic Flowmeter (AM12): GS 1E6K2-E BT2 Brain Terminal: GS 1CA11-E AXF Magnetic Flowmeter Integral Flowmeter/ Remote Flowtube: GS 1E2D1-1E AXFA14G/C Magnetic Flowmeter Remote Converter: GS 1E2C2-1E FieldMate: GS 1R1A1-1E REFERENCE Company names and product names used in this material are registered trademarks or trademarks of their respective owners. Subject change without notice.