105~150W Constant Current Mode LED Driver ELG-150-C series

Transcription

1 THOMAS SAMUEL THOMAS SAMUEL ~150W Constant Current Mode LED Driver ELG150C series IP65 IP67 IS 15885(Part 2/Sec13) R (for 700A,0A,700DA only) A Dx {

2 SPECIFICATION MODEL OUTPUT INPUT ~150W Constant Current Mode LED Driver ELG150C series RATED CURRENT RATED POWER SET UP TIME Note.4 VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) Note.3 INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY OTHERS NOTE CONSTANT CURRENT REGION Note ~ 300V OPEN CIRCUIT VOLTAGE(max.) 315V 225V 151V 115V 94V 80V Adjustable for A/ABType only (via builtin potentiometer) CURRENT ADJ. RANGE 250 ~ 500mA 0 ~ 700mA 525 ~ 0mA 700 ~ 1400mA 875 ~ 1750mA 0 ~ 2100mA CURRENT RIPPLE 5.0% current CURRENT TOLERANCE ±5.0% TOTAL HARMONIC DISTORTION SHORT CIRCUIT OVER TEMPERATURE MAX. CASE TEMP. TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS DALI STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING (For All the Types) (Except for BE Type) (For BE Type only) CONSTANT CURRENT REGION Note.2 (For BE Type only) AUXILIARY DC OUTPUT EFFICIENCY (Typ.)(for BE Type only) NO LOAD / STANDBY POWER CONSUMPTION ELG150C ms/115VAC ELG150C mA 700mA 100VAC ~ 180VAC W W 0VAC ~ 305VAC 107 ~ 214V 500ms/230VAC ELG150C0 0mA 72 ~ 143V Nominal 15V(deviation 11.5~15.5V)@0.3A for BEType only 100 ~ 305VAC 142 ~ 431VDC continue,3vac for 24Hrs; 360VAC for 1Hr (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ Hz 1.7A / 115VAC 0.9A / 230VAC 0.7A/277VAC COLD START 65A(twidth= 485μ s measured at 50% Ipeak)/230VAC; Per NEMA units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC No load power consumption <0.5W for Blank / A / Dx / D2Type Standby power consumption <0.5W for B / AB / DAType Hiccup mode, recovers automatically after fault condition is removed 3 ~ 360V 230 ~ 265V 155 ~ 180V 128 ~ 150V 96 ~ 106V 82 ~ 92V Shut down o/p voltage, repower on to recover Shut down o/p voltage, repower on to recover Tcase=40 ~ 90 (Please refer to OUTPUT LOAD vs TEMPERATURE section) Tcase=90 ~ 95% RH noncondensing 40 ~ 80, 10 ~ 95% RH ± 0.03%/ (0 ~ 60 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750 (type HL )(except for BEtype), CSA C22.2 No ;EN/AS/NZS ,EN/AS/NZS independent, EN62384; GB ,GB ,EAC TP TC 004,BIS IS15885(for 700A,0A,700DA only),ip65 or IP67; KC KN , KN approved I/PO/P:3.75KVAC I/PFG:2.0KVAC O/PFG:1.5KVAC ELG150C mA 54 ~ 107V PF 0.97/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) ELG150C mA 43 ~ 86V ELG150C mA 36 ~ 72V 92% 92% 92% 91% 91% 91% 90% 90% 90% 89% 89% 89% I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015,EN Class C (@load 60%) ; EN ; GB17743, GB ; EAC TP TC 0; KC KN15, KN61547 Compliance to EN ,3,4,5,6,8,11; EN61547, light industry level ( surge immunity LineEarth 6KV, LineLine 4KV ), EAC TP TC 0; KC KN15, KN K hrs min. Telcordia SR332 (Bellcore) 308.5Khrs min. MILHDBK217F (25 ) ** mm (L*W*H) 0.95Kg; 16pcs / 16.0kg / 0.77CUFT W W W W 150W 149.8W W 149.8W 150.5W 151.2W 1W 134.4W 134.4W 133W 133W 134.4W 150 ~ 270V 107 ~ 192V 72 ~ 128V 54 ~ 95V 43 ~ 76V 36 ~ 64V Compliance to IEC ,102,7 for DAType only

3 BLOCK DIAGRAM PFC fosc : 50~1KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT Vo Vo DIM DIM (B Type) O.V.P. CASE :Protective Earth DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. 100 Vo(%) 50 (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL Io(%) Typical output current normalized by rated current (%) This characteristic applies to Blank/A/B/AB/DX/D2/BEType, For DAType, the Constant Current area is 60%~100% Vo.

4 DIMMING OPERATION ELG150C DIM( Gray)* DIM(Black)** 3 in 1 dimming function (for B/ABType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) * DIM for B/ABType DA for DAType PROG for D2Type * *DIM for B/ABType DA for DAType PROG for D2Type Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 0% 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: Vo Applying additive 0 ~ 10VDC Vo Vo DIM Additive Voltage DIM DO NOT connect "DIM to Vo" Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): Vo Vo DIM Additive PWM signal DIM DO NOT connect "DIM to Vo" Vo DIM DIM Additive Resistance 10% DO NOT connect "DIM to Vo" 0% Short 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% %

5 DALI Interface (primary side; for DAType) Apply DALI signal between DA and DA. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output. Smart timer dimming function (for DxxType by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details. Ex : D01Type: the profile recommended for residential lighting Set up for D01Type in Smart timer dimming software program: Dimming Level(%) TIME** LEVEL** T1 T2 06:00 07:00 100% 70% T3 11:00 50% T4 70% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a residential lighting application adopts D01Type, when turning on the power supply at 6:00pm, for instance: [1] The power supply will swih to the constant current level at 100% starting from 6:00pm. [2] The power supply will swih to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will swih to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will swih to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 8:00am, which is 14:00 after the power supply turns on. Ex: D02Type: the profile recommended for street lighting Set up for D02Type in Smart timer dimming software program: Dimming Level(%) TIME** LEVEL** T1 01:00 50% T2 03:00 80% T3 T4 T5 8:00 11:00 100% 60% 80% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a street lighting application adopts D02Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will swih to the constant current level at 50% starting from 5:00pm. [2] The power supply will swih to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will swih to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will swih to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will swih to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.

6 Ex: D03Type: the profile recommended for tunnel lighting Set up for D03Type in Smart timer dimming software program: Dimming Level(%) T1 T2 T3 TIME** 01:30 11:00 LEVEL** 70% 100% 70% Operating Time(HH:MM) **: TIME mahes Operating Time in the diagram whereas LEVEL mahes Dimming Level. Example: If a tunnel lighting application adopts D03Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will swih to the constant current level at 70% starting from 4:30pm. [2] The power supply will swih to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will swih to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.

7 OUTPUT LOAD vs TEMPERATURE(Note.7) VAC input only for BE Type VAC input only LOAD (%) 40 LOAD (%) (HORIZONTAL) (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at LOAD (%) PF V(150W) 230V(150W) 115V(W) % 60% 70% 80% 90% 100% INPUT VOLTAGE (V) 60Hz LOAD Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD ELG150C series possess superior working efficiency that up to 92% can be reached in field applications. 500mA Model, Tcase at mA Model, Tcase at 75 THD 22% % 18% 16% 14% 12% 10% 8% 6% 4% 2% 50% 60% 70% 80% 90% 100% 277VAC(150W) 230VAC(150W) 115VAC(W) EFFICIENCY(%) % 60% 70% 80% 90% 100% 277V(150W) 230V(150W) 115V(W) LOAD LOAD

8 LIFE TIME LIFETIME(Kh) Tc a s e ( )

9 MECHANICAL SPECIFICATION BlankType CASE NO.: 237A Unit:mm 300± ± AType(except for 1750mA, 2100mA models) 300± ±

10 AType(for 1750mA, 2100mA models) 300± ± B/ DA/D2Type 300± ± DIM( Gray)* DIM(Black)** * DIM for BType DA for DAType PROG for D2Type * *DIM for BType DA for DAType PROG for D2Type

11 ABType(except for 1750mA, 2100mA models) 300± ± DIM( Gray) DIM(Black) ABType(for 1750mA, 2100mA models) 300± ± DIM( Gray) DIM(Black) 50

12 BEType 300± ± FG (Green/Yellow) SJOW 17AWGx3C SJOW 17AWGx4C 300± AUX( Red) AUX(White) DIM( Gray) DIM(Black) 3Y Model (3wire input) 300± PE (Green/Yellow) SJOW 17AWGx3C Note1: Please connect the case to PE for the complete EMC deliverance and safety use. Note2: Please contact MEAN WELL for input wiring option with PE. INSTALLATION MANUAL Please refer to :