HBG-100 series. 100W Constant Current Mode LED Driver IP65 IP67. File Name:HBG-100-SPEC

Transcription

1 IP65 IP67 Ⅰ A E

2 SPECIFICATION MODEL HBG10024 HBG10036 HBG10048 HBG10060 RATED CURRENT 4A 2.7A 2A 1.6A RATED POWER 96W 97.2W 96W 96W CONSTANT CURRENT REGION Note ~ 24V 21.6 ~ 36V 28.8 ~ 48V 36 ~ 60V OPEN CIRCUIT VOLTAGE(max.) 25V 37V 49V 62V OUTPUT Adjustable for AType (via builtin potentiometer) CURRENT ADJ. RANGE 2.4 ~ 4A 1.62 ~ 2.7A 1.2 ~ 2A 1.0 ~ 1.6A CURRENT RIPPLE 5.0% current CURRENT TOLERANCE ±5.0% SETUP TIME Note.4 00ms / 115VAC 500ms / 230VAC VOLTAGE RANGE Note.3 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR PF>0.96/115VAC, PF>0.96/230VAC, PF>0.94/277VAC@ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@load 75%/277VAC) INPUT TOTAL HARMONIC DISTORTION (Please refer to TOTAL HARMONIC DISTORTION(THD) section) EFFICIENCY (Typ.) 90.5% 91% 91% 91.5% AC CURRENT (Typ.) 1.1A / 115VAC 0.5A / 230VAC 0.45A / 277VAC INRUSH CURRENT (Typ.) COLD START 60A(twidth=415μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 MAX. No. of PSUs on 16A CIRCUIT BREAKER 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC OVER CURRENT 95 ~ 108% Constant current limiting PROTECTION OVER VOLTAGE 28 ~ 35V 41 ~ 49V 54 ~ 63V 65 ~ 75V Shut down o/p voltage repower on to recovery OVER TEMPERATURE Shut down o/p voltage repower on to recovery WORKING TEMP. Tcase=40 ~ 85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=85 ENVIRONMENT WORKING HUMIDITY ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY & EMC OTHERS NOTE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note. 8 UL8750(type HL ),CSA C22.2 No , ENEC EN613471, EN independent, EN62384; IP65 or IP67 approved I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:0.5KVAC I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN Class C (@load 60%) ; EN EMC IMMUNITY Compliance to EN ,3,4,5,6,8,11, EN61547,light industry level ( surge immunity:lineearth:4kv,lineline:2kv) MTBF 985.6K hrs min. Telcordia SR332 (Bellcore) ; 300 Khrs min. MILHDBK217F (25 ) DIMENSION ψ130mm *66.5mm (D * H) PACKING 1.18Kg; 12pcs/15.7Kg/1.43CUFT(Blank/A/B Type),1.89CUFT(E Type)

3 BLOCK DIAGRAM fosc : 100KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.C.P. V V FG O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. 100 Vo(%) 60 (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL Io(%) Typical output current normalized by rated current (%)

4 DIMMING OPERATION AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG*3C SJTW 18AWG*2C V(Red) V(Black) DIM(White) DIM(Blue) UL AWG*2C 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 1 ~ 10VDC 100% 90% V V DIM DIM Additive Voltage Output current (%) 80% 70% 60% 50% 40% 30% % DO NOT connect "DIM to V" 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Applying additive resistance: Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input V 100% 90% V DIM DIM DO NOT connect "DIM to V" Additive Resistance Output current (%) 80% 70% 60% 50% 40% 30% % 10% 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HBG100CSPEC

5 Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HBG100 BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture.

6 OUTPUT LOAD vs TEMPERATURE VAC Input only VAC Input only LOAD (%) LOAD (%) (HORIZONTAL) (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at LOAD (%) PF V 230V 115V INPUT VOLTAGE (V) 60Hz Derating is needed under low input voltage % 60% 70% 80% 90% 100% (100W) LOAD TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 75 EFFICIENCY vs LOAD possess superior working efficiency that up to 91% can be reached in field applications. 48V Model, Tcase at 75 18% 16% 14% THD 12% 10% 8% 6% 4% 2% 0% 50% 60% 70% 80% 90% 100% 277VAC 230VAC 115VAC EFFICIENCY(%) % % 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V LOAD LOAD

7 LIFE TIME LIFETIME(Kh) Tc a s e ( )

8 MECHANICAL SPECIFICATION Case No.217 Unit:mm BlankType ψ ± M10*P1.5*18h 3 tc AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG*3C 0± SJTW 18AWG*2C V(Red) V(Black) ψ6.0 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point Ta AType ψ M10*P1.5*18h 3 tc AC/L(Brown) AC/N(Blue) FG (Green/Yellow) 300± SJTW 18AWG*3C 0± SJTW 18AWG*2C V(Red) V(Black) ψ6.0 Ta tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point BType ψ ± M10*P1.5*18h 3 tc AC/L(Brown) AC/N(Blue) FG (Green/Yellow) DIM(White) DIM(Blue) SJTW 18AWG*3C 300± UL AWG*2C 0± SJTW 18AWG*2C V(Red) V(Black) ψ6.0 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point Ta

9 EType ψ ± 130 M10*P1.5*18h 3 tc AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG*3C 0± SJTW 18AWG*2C V(Red) V(Black) ψ6.0 Ta 160 tc : Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point INSTALLATIONS Hanger Chain Spot Light High Bay Light Stage Light Caution Please inspect the appearance of the driver if the package is damaged. There should not be any cracks. Please do not drop or bump the driver. All screws including the suspension screw should be paired with a spring washer and locked tight. The entire luminaire, including the driver, should be limited to 10Kg or less. The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation. Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.

10 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Mean Well: HBG10048B HBG10036 HBG10048A HBG10060B HBG10060A HBG10024B HBG10048 HBG10024 HBG10036A HBG10060 HBG10024A HBG10036B