FDL-65 series. 65W Constant Current Mode LED Driver IP65. File Name:FDL-65-SPEC

Transcription

1 IP65 ~

2 SPECIFICATION MODEL FDL RATED CURRENT RATED POWER 1550mA 65.1W CONSTANT CURRENT REGION Note ~ 42V OUTPUT OPEN CIRCUIT VOLTAGE(max.) 50V CURRENT ADJ. RANGE A CURRENT TOLERANCE ±5.0% INPUT OTHERS NOTE SET UP TIME Note.3 VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) TOTAL HARMONIC DISTORTION EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER EMC IMMUNITY MTBF DIMENSION PACKING 500ms/230VAC FDL mA 64.8W 21.6 ~ 36V 1 ~ 295VAC 254 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF 0.95/230VAC, PF 0.90/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) 0.48A / 230VAC 0.39A/277VAC COLD START 50A(twidth= 270μ s measured at 50% Ipeak)/230VAC; Per NEMA units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC <0.5W SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE 46 ~ 56V ~ 48V Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. Tcase=- ~ +90 (Please refer to OUTPUT vs TEMPERATURE section) MAX. CASE TEMP. Tcase=+90 WORKING HUMIDITY 20 ~ 95% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY - ~ +, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS LVD EN ,EN Independent, GB ,GB ,IP65 approved SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC EMC ISOLATION RESISTANCE I/P-O/P:M Ohms / 500VDC / 25 / 70% RH EMC EMISSION Compliance to EN55015, EN-3-2 Class C (load %) ; EN-3-3,GB17743,GB V 90% 90% Compliance to EN-4-2,3,4,5,6,8,11; EN61547, light industry level(surge immunity:line-earth:4kv,line-line:2kv) 594.9K hrs min. MIL-HDBK-217F (25 ) 151*53*31.5mm (L*W*H) 0.42Kg; 24pcs / 11.08Kg / 0.73CUFT 0.9~1.8A THD< 20%(@load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section)

3 BLOCK DIAGRAM PWM fosc : ~130KHz I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER +V -V O.V.P. O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT CASE GROUND DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. Vo(%) (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 Io(%) Typical output current normalized by rated current (%)

4 OUTPUT vs TEMPERATURE AMBIENT TEMPERATURE,Ta ( ) (HORIZONTAL) Tcase ( ) (HORIZONTAL) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at PF V 230V INPUT VOLTAGE (V) Hz 0.8 % 70% % 90% % TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs possess superior working efficiency that up to 90% can be reached in field applications. 10mA Model,Tcase at 10mA Model, Tcase at 25% THD 20% 15% 10% 5% 277VAC 230VAC EFFICIENCY(%) V 230V 0% 88.5 % 70% % 90% % 88 % 70% % 90% %

5 MECHANICAL SPECIFICATION ± ±20 CASE NO.: 246A Unit:mm AC/N(Blue) AC/L(Brown) H05RN 1.0mm²*2C 4xψ4.5 4xψ tc H05RN 1.0mm²*2C -V(Blue) +V(Brown) tc : Max. Case Temperature Note: Please connect the case to FG for the complete EMC deliverance. INSTALLATION MANUAL Please refer to :