PWM-120 series. 120W PWM Output LED Driver. IS 15885(Part 2/Sec13) IP67. R ( for PWM ,24 only) File Name:PWM-120-SPEC

Transcription

1 THOMAS SAMUEL THOMAS SAMUEL IS 188(Part 2/Sec13) IP67 R ( for PWM112,24 only) 0 except for 12DA type ~

2 SPECIFICATION MODEL OUTPUT INPUT PROTECTION DC VOLTAGE RATED CURRENT RATED POWER SETUP, RISE TIME Note.2 HOLD UP TIME (Typ.) VOLTAGE RANGE Note.3 FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT WORKING TEMP. WORKING HUMIDITY ~ 9% RH noncondensing ENVIRONMENT STORAGE TEMP., HUMIDITY 40 ~, 10 ~ 9% RH SAFETY & EMC OTHERS NOTE DIMMING RANGE PWM FREQUENCY (Typ.) TOTAL HARMONIC DISTORTION MAX. NO. of PSUs on 16A CIRCUIT BREAKER NO LOAD/STANDBY POWER CONSUMPTION OVERLOAD SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE MAX. CASE TEMP. TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS Note. DALI STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note.6 EMC IMMUNITY MTBF DIMENSION PACKING 12V 24V 36V 48V PWM112 PWM124 PWM136 PWM148 10A A 3.4A 2.A 1W 1W 122.4W 1W 0 ~ 100% 1.47kHz 00ms, ms/ 230VAC or 11VAC 16ms/230VAC or 11VAC 90 ~ 30VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF>0.97/11VAC, PF>0.96/230VAC, full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< %(@load 60%/11VAC, 7%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION section) 88% 90% 90% 90.% 1.3A / 11VAC 0.6A / 230VAC 0.A / 277VAC COLD START 60A(twidth= μs measured at 0% Ipeak) at 230VAC ; Per NEMA units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC <0.2mA / 277VAC No load power consumption<0.w for blanktype;standby power consumption<0.w for DAtype 108 ~ 1% rated output power Hiccup mode, recovers automatically after fault condition is removed Shut down o/p voltage, repower on to recover 1 ~ 17V 28 ~ 34V 41 ~ 46V 4 ~ 60V Shut down o/p voltage, repower on to recover Shut down o/p voltage, repower on to recover Tcase=40 ~ 90 (Please refer to OUTPUT LOAD vs TEMPERATURE section) Tcase=90 ±0.03%/ (0 ~ 4,except 0 ~ 40 for 12V) 10 ~ 00Hz, G 12min./1cycle, period for 72min. each along X, Y, Z axes UL870( type HL )(except for 12DA type), CSA C22.2 No ; ENEC EN613471, EN ,EN62384 independent, IP67,BIS IS188( for PWM112,24 only), EAC TP TC 004,GB1910.1,GB approved; Design refer to EN60331 Comply with IEC , 102, 7 for DAType only I/PO/P:3.7KVAC I/PO/P:100M Ohms / 00VDC / 2 / 70% RH Compliance to EN01, EN Class C (@load 60%) ; EN ,GB17743 and GB1762.1,EAC TP TC 0 Compliance to EN ,3,4,,6,8,11; EN6147, light industry level (surge immunity LineLine 2KV),EAC TP TC K hrs min. Telcordia SR332 (Bellcore) ; 228.7K hrs min. MILHDBK217F (2 ) 191*63*37.mm (L*W*H) 0.97Kg; 1pcs/1.6Kg/0.87CUFT

3 DIMMING OPERATION AC/L(Brown) AC/N(Blue) PWM1 DIM(Blue)* DIM(White)** V(Red)(Brown for DAtype) V(Black)(Blue for DAtype) Dimming principle for PWM style output Dimming is achieved by varying the duty cycle of the output current. * DIM for BlankType DA for DAtype * *DIM for BlankType DA for DAtype Output DC current ON TON Duty cycle(%) = 100% T Io=0A TON OFF Output PWM frequency : 1.47KHz fixed (Typ.) T 3 in 1 dimming function (for BlankType) Apply one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Dimming source current from power supply: 100μA (typ.) Applying additive 0 ~ 10VDC 100% 90% V V DIM DIM Additive Voltage LED Strips 0.1% Duty cycle of output current (%) % 70% 60% 0% 40% 30% % DO NOT connect "DIM to V" 0.6V 1V 0% 0V 1V 2V 3V 4V V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): 100% V V DIM DIM LED Strips Additive PWM signal 0.1% Duty cycle of output current (%) 90% % 70% 60% 0% 40% 30% % DO NOT connect "DIM to V" 6% 0% % 30% 40% 0% 60% 70% % 90% 100% Duty cycle of additive 10V PWM signal dimming input

4 Applying additive resistance: 100% V V DIM DIM LED Strips Additive Resistance Duty cycle of output current (%) 90% % 70% 60% 0% 40% 30% % DO NOT connect "DIM to V" 0.1% 6K/N 10K/N 0% Short 10K/N K/N 30K/N 40K/N 0K/N 60K/N 70K/N K/N 90K/N 100K/N (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance Note : 1. Min. duty cycle of output current is about 0.1%, and the dimming input is about 6KΩ or 0.6VDC, or 10V PWM signal with 6% duty cycle. 2. The duty cycle of output current could drop down to 0% when dimming input is less than 6KΩ or less than 0.6VDC, or 10V PWM signal with duty cycle less than 6%. DALI Interface (primary side; for DAType) Apply DALI signal between DA and DA. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 6% of output

5 OUTPUT LOAD vs TEMPERATURE LOAD (%) VAC Input only 0 12V only LOAD (%) VAC Input only AMBIENT TEMPERATURE,Ta ( ) (HORIZONTAL) Tcase ( ) (HORIZONTAL) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at LOAD (%) INPUT VOLTAGE (V) 60Hz PF % 30% 40% 0% 60% 70% % 90% 100% (7W) LOAD 277V 230V 11V Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD possess superior working efficiency that up to 90.% can be reached in field applications. 48V Model, Tcase at 48V Model, Tcase at THD 30% 2% % 1% % 0% 0% 60% 70% % 90% 100% LOAD 277VAC 230VAC 11VAC EFFICIENCY(%) % 30% 40% 0% 60% 70% % 90% 100% LOAD 277V 230V 11V

6 LIFE TIME LIFETIME(Kh) Tc a s e ( )

7 Block Diagram PFC fosc : 0~1KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS V & DIMMING V FILTER CIRCUIT O.L.P. DETECTION CIRCUIT DIM DIM O.V.P. Mechanical Specification Case No. PWM1 Unit:mm BlankType 300± ± AC/L(Brown) AC/N(Blue) 0±3 SJTW 18AWG 2C 2ψ4. 63 T case tc tc : Max. Case Temperature UL AWG 2C SJTW 14AWG 2C 0±3 DIM(Blue) DIM(White) V(Red) V(Black) DAType 300± ± AC/L(Brown) AC/N(Blue) 0±3 SJOW 17AWG 2C 2 &H0RNF 1.0mm 2ψ4. 63 T case tc tc : Max. Case Temperature UL AWG 2C SJOW 17AWG 2C 2 &H0RNF 1.0mm 0±3 DA(Blue) DA(White) V(Brown) V(Blue) 3

8 Recommend Mounting Direction Installation Manual Connection for Blanktype AC/L(BROWN) AC/N(BLUE) V(BLACK) V(RED) DIM(WHITE) 0~10Vdc or 10V PWM or resistance Dimmer DIM(BLUE) LED Strip Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be reconnected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 101 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a derating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the system. For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.pwm series require 0.1mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect "DIM to V". Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must requalify EMC Directive on the complete installation again. For more information about installation, Please refer to : for details.