DRIV-ZT-24V-90W LED 0-10V Dimming Driver, Wet Location

Transcription

1 LED 010V Dimming Driver, Wet Location SPECIFICATION OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE PWM FREQUENCY (Typ.) VOLTAGE TOLERANCE SETUP, RISE TIME Note.2 HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER LOAD SHORT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS MTBF DIMENSION PACKING 24V 3.7A 90W 0 ~ 100% 300Hz ±3.0% 00ms, ms 11VAC / 230VAC at full load 16ms/230VAC 90 ~ 30VAC 127 ~ 431VDC 47 ~ 63Hz 16ms/11VAC at full load PF>0.98/11VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION THD< 20% when output loading 60% at 11VAC/230VAC input and output loading 7% at 277VAC input WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY 90.% 0.9A / 11VAC 0.A / 230VAC 0.4A / 277VAC COLD START 60A(twidth=0 μs measured at 0% Ipeak) at 230VAC <0.2mA / 277VAC 108 ~ 120% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 28 ~ 34V Protection type : Shut down o/p voltage, repower on to recover Shut down o/p voltage, repower on to recover 40 ~ 70 (Refer to "Derating Curve") 20 ~ 9% RH noncondensing 40 ~, 10 ~ 9% RH ±0.03%/ (0 ~ 0 ) 10 ~ 00Hz, G 12min./1cycle, period for 72min. each along X, Y, Z axes UL870, CSA C22.2 No , ENEC EN613471, EN , EN62384 independent, IP67 approved ; Design refer to EN60331 I/PO/P:3.7KVAC I/PO/P:100M Ohms / 00VDC / 2 / 70% RH Compliance to EN01, EN Class C ( 60% load) ; EN Compliance to EN ,3,4,,6,8,11; EN6147, light industry level(surge L N : 2KV), criteria A 224.2K hrs min. MILHDBK217F (2 ) 171*63*37.mm (L*W*H) 0.77Kg; 18pcs/14.9Kg/0.82CUFT

2 LED 010V Dimming Driver, Wet Location Block Diagram PFC fosc : 0~120KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS V & DIMMING V FILTER O.L.P. DETECTION DIM DIM O.V.P. Derating Curve Static Characteristics LOAD (%) VAC Input only LOAD (%) AMBIENT TEMPERATURE ( ) (HORIZONTAL) INPUT VOLTAGE (V) 60Hz Power Factor Characteristic PF Constant Voltage Mode % 20% 30% 40% 0% 60% 70% % 90% 100% LOAD (90W) 277V 230V 11V

3 LED 010V Dimming Driver, Wet Location EFFICIENCY vs LOAD PWM90 series possess superior working efficiency that up to 90.% can be reached in field applications. EFFICIENCY (%) % 20% 30% 40% 0% 60% 70% % 90% 100% LOAD 277V 230V 11V DIMMING OPERATION The PWM style output is a simple switching of supply ON/OFF at a rate so fast that the human eye cannot see led flickering. Duty cycle describes the proportion of time when output voltage is on relative to the entire period of time. It is expressed in percentage, 100% being fully on (maximal brightness) and a low duty cycle corresponding to lower brightness. Builtin 3 in 1 dimming function. The duty of the PWM style output can be adjusted through output cable by connecting a 0~10Vdc or 10V PWM signal or resistance between DIM and DIM. Connection V LED Strips V DIM 0~10Vdc or 10V PWM or resistance control dimmer DIM DO NOT connect "DIM to V"

4 LED 010V Dimming Driver, Wet Location Duty cycle of output current VS Dimming input 100% when DIM/DIM are open circuit. 100% 90% % 70% NonLinear 60% Duty cycle of output current 0% 40% 30% 20% 10% 0% 0V 1V 2V 3V 4V V 6V 7V 8V 9V 10V 0~10Vdc 0% 10% 20% 30% 40% 0% 60% 70% % 90% 100% Duty cycle of 10V PWM (frequency range = 100~3KHz) 0K 10K 20K 30K 40K 0K 60K 70K K 90K 100K 0~100KΩresistance Dimming input PWM Style Output Output DC current ON TON Duty cycle(%) = 100% T OFF Output PWM frequency : 300Hz fixed (Typ.) TON T Mechanical Specification Case No. PWM90P ±20 300±20 Unit:mm AC/L(Brown) AC/N(Blue) SJTW 18AWG 2C 63 T case: Max. Case Temperature. SJTW 16AWG 2C UL AWG 2C 37. 2ψ V(Red) V(Black) DIM(Blue) DIM(White) Recommend Mounting Direction

5 LED 010V Dimming Driver, Wet Location Installation Manual Connection AC/L(BROWN) AC/N(BLUE) V(RED) V(BLACK) LED Strip DIM(BLUE) DIM(WHITE) 0~10Vdc or 10V PWM or resistance Dimmer Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be reconnected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 101 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a derating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. For LED power supplies with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the system. For dimmable LED power supplies, make sure that your dimming controller is capable of driving these units.pwm series require 0.1mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect "DIM to V". Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes.