PI3C3125/PI3C3126. Description
|
|
- Cornelia Melton
- 5 years ago
- Views:
Transcription
1 .V/.V, High Bandwidth, Hot Insertion,-Bit, -Port Bus Switch with Individual Enables Features Near-Zero propagation delay -ohm switches connect inputs to outputs High Bandwidth (>00 MHz) Rail-to-Rail, or.v or.v Switching V I/O Tolerant.V Supply Voltage Operation Permits Hot Insertion Packaging (Pb-free & Green available): -pin 0-mil wide plastic SOIC (W) -pin 0-mil wide plastic TSSOP (L) -pin 0-mil wide plastic QSOP (Q) Description Diodes PIC and PIC are. volt or. volt, -bit bus switches designed with four individual -ohm bus switches with fast indiviual enables in an industry standard XX/ pinout. When enabled via the associated Bus Enable pin, the A pin is directly connected to the B pin for that particular gate. The bus switch introduces no additional propagation delay or additional ground bounce noise. The PIC device has active LOW enables, and the PIC has active HIGH enables. It is very useful in switching signals that have high bandwidth (>00 MHz). Applications High Bandwidth Data Switching Hot Docking PIC Block Diagram PIC Block Diagram
2 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature... C to +0 C Ambient Temperature with Power Applied... 0 C to + C Supply Voltage to Ground Potential (Inputs & VCC Only)... 0.V to +.V Supply Voltage to Ground Potential (Outputs & D/O Only)... 0.V to +.V DC Input Voltage... 0.V to +.V DC Output Current... 0mA Junction Temperature... C Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. PIC -Pin Configuration PIC -Pin Configuration -PIN W L 0 9 Vcc -PIN W L 0 9 Vcc PIC -Pin Configuration PIC -Pin Configuration NC -PIN Q 0 9 Vcc NC NC -PIN Q 0 9 Vcc NC Pin Description Pin Name Description BEn Switch Enable (PIC) BEn Switch Enable (PIC) - Bus A - Bus B V CC Power Ground Truth Table () PIC BEn PIC BEn An Bn V CC Function X* X Hi-Z Hi-Z Disconnect H L Hi-Z Hi-Z V CC Disconnect L H Bn An V CC Disconnect Note:. H = High Voltage Level, L = Low Voltage Level HI-Z = High Impedance, X = Don t Care * A pull-up resistor should be provided for power-up protection.
3 DC Electrical Characteristics (Over Operating Range, TA = 0 C to + C, VCC =.V ±0%) Parameters Description Test Conditions () Min. Typ. () Max Units V IH Input HIGH Voltage Guearanteed Logic HIGH Level.0 V V IL Input LOW Voltage Guaranteed Logic LOW Level I IH Input HIGH current V CC = Max., V IN = V CC ± µa I IL Input LOW Current V CC = Max., V IN = ± µa I () OZH High Impedance Output 0 A, B V CC ± Current V IK Clamp Diode Voltage V CC = Min., I IN = ma 0.. V R ON Switch ON Resistance () V CC = Min., V IN = 0.0V, I ON = ma or 0mA Ω V CC = Min., V IN =.V, I ON = ma. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.. Typical values are at VCC =.V, TA = C ambient and maximum loading.. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. Capacitance (TA = C, f = MHz) Parameters () Description Test Conditions Typ. Units C IN Input Capacitance VIN = 0V. C OFF A/B Capacitance, Switch Off VIN = 0V.0 pf C ON A/B Capacitance, Switch On VIN = 0V 0.0. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters Description Test Conditions Min. Typ. () Max. Units I CC Quiescent Power Supply V CC = Max V IN = or V CC 0 00 Current µa I CC Supply Current per Input HIGH V CC = Max V IN =.0V () 0. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.. Typical values are at VCC =.V, + C ambient.. Per driven input (control input only); A and B pins do not contribute to ΔICC.
4 Switching Characteristics over.v Operating Range Parameters Description Conditions t PLH Propogation Delay (,) t PHL A to B, B to A C L =0pF R L = 00Ω Com. Min. Max. Bus Enable Time C =0pF.. t PZH.. t PZL t PHZ Bus Disable Time L R L = 00Ω R = 00Ω t PLZ. This parameter is guaranteed but not tested on Propagation Delays.. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.ns for 0pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Switching Characteristics over.v Operating Range Parameters Description Conditions t PLH Propogation Delay (,) t PHL A to B, B to A C L =0pF R L = 00Ω 0. Com. Min. Max. 0. Bus Enable Time C =0pF.. t PZH. 9. t PZL t PHZ Bus Disable Time L R L = 00Ω R = 00Ω t PLZ. This parameter is guaranteed but not tested on Propagation Delays.. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.ns for 0pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Units ns Units ns.0 V CC V.V.9V.V.V.V.V.V.V.V.0V.V V O U T ) VIN (V) Switch Output Voltage vs. Input Voltage over Various Supply Voltages
5 Packaging Mechanical: -SOIC (W) -00
6 Packaging Mechanical: -TSSOP (L) -000
7 Packaging Mechanical: -QSOP (Q) -00 For latest package info. please check: Ordering Information Ordering Code Packaging Code Description PICLEX L -pin, mil Wide (TSSOP) PICWEX W -pin, 0mil Wide (SOIC) PICLEX L -pin, mil Wide (TSSOP) PICQEX Q -pin, 0mil Wide (QSOP) Thermal characteristics can be found on the company web site at E = Pb-free and Green X suffix = Tape/Reel
8 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. does not assume any liability arising out of the application or use of this document or any product described herein; neither does convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold and all the companies whose products are represented on website, harmless against all damages. does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use products for any unintended or unauthorized application, Customers shall indemnify and hold and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by. LIFE SUPPORT products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of. As used herein: A. Life support devices or systems are devices or systems which:. are intended to implant into the body, or. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by. Further, Customers must fully indemnify and its representatives against any damages arising out of the use of products in such safety-critical, life support devices or systems. Copyright 0,
PI3C3305/PI3C3306. Features. Description. Applications. PI3C3306 Block Diagram. PI3C3305 Block Diagram. PI3C Pin Configuration
2.5V/3., High-Bandwidth, Hot-Insertion, 2-Bit, 2-Port Bus Switch w/ Individual Enables Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High Bandwidth (>400 MHz) Rail-to-Rail,
More informationPI3C3245. Description. Features. Truth Table (1) Pin Description. Pin Name Description. Function BE A0-7. A product Line of. Diodes Incorporated
Pb Lead-free Green A product Line of 2.5V/3.3V, High Bandwidth, Hot Insertion 8-Bit, 2-Port, Bus Switch Features ÎÎNear-Zero propagation delay ÎÎ5-ohm switches connect inputs to outputs ÎÎHigh Bandwidth
More informationPI3B3125/PI3B3126. Description. Features. A product Line of. Diodes Incorporated. 3.3V, 4-Bit, 2-Port Nanoswitchw/Individual Enables
.V, -Bit, -Port Nanoswitchw/Individual Enables Features ¼¼Near zero propagation delay ¼¼5 Ohm switches connect inputs to outputs ¼¼Fast Switching Speed - ns max. ¼¼Ultra Low Quiescent Power (0.µA Typical)
More informationPI3C3126. Description. Features. 14-Pin Configuration. Applications. Block Diagram. 16-Pin Configuration. Truth Table (1) Pin Description.
2./3.3, High Bandwidth, Hot Insertion,4-Bit, 2-Port Bus Switch with Individual Enables Features Near-Zero propagation delay -ohm switches connect inputs to outputs High Bandwidth (>400 MHz) 2./3.3 Supply
More informationDescription. Applications
8-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description - - Applications Pin Configuration Block Diagram TSSOP QSOP TQFN Pin Description Pin No Pin Name Description 19
More informationFeatures. Description. Pin Configuration. Block Diagram. Truth Table (1) PI3CH480. TSSOP/QSOP Top View. UQFN3x3-16 Top View
4-Channel 2:1 Mux/DeMux, Enable Low 1.8V / 2.5V / 3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond
More informationPI3C V/3.3V, High Bandwidth, Hot Insertion 8-Bit, 2-Port, Bus Switch. Description. Features. Pin Configuration. Block Diagram.
Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth Operation (>400 MHz) Permits Hot Insertion 5V I/O Tolerant Rail-to-Rail 3.3V or 2.5V Switching 2.5V Supply Voltage
More informationDescription. Features. Pin Description. Pin Configuration PI4GTL bit GTL to GTL Transceiver
4-bit GTL to GTL Transceiver Features Operates as a 4-bit GTL /GTL/GTL+ to GTL /GTL/GTL+ bus buffer 2.3 V to 3.6 V operation GTL input and output 3.6 V tolerant Vref adjustable from 0.5 V to VCC/2 Partial
More informationDescription. Pin Description
4-bit LVTTL to GTL transceiver Features Operates as a 4-bit GTL /GTL/GTL+ sampling receiver or as a LVTTL to GTL /GTL/GTL+ driver 2.3 V to 3.6 V operation with 5 V tolerant LVTTL input GTL input and output
More informationA product Line of Diodes Incorporated. Description EN S 1 IA 3 IA 2 IA 1 GND. Note: 1. N.C. = No internal connection.
Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Features ÎÎNear-Zero propagation delay ÎÎ5Ω switches connect inputs to outputs ÎÎHigh signal passing bandwidth (-3dB BW is 815MHz)
More informationSOTiny TM Low Resistance, Low-Voltage Single-Supply SPDT Switch
SOTiny TM Low Resistance, Low-Voltage Single-Supply SPDT Switch Features Description Pin Assignment Applications Pin Description PI5A4599B Pin No Pin Name Description 1 Logic control 2 Positive Power Supply
More informationDescription. Features. Applications. Pin Assignment. Pin Description Pin No Pin Name. Logic Function Table Logic Inputs(S) PI5A4157
Low Voltage SPDT 0.8Ω Analog Switch Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.8Ω at 3.0V Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage
More information74LVC125A. Pin Assignments. Description. Features. Applications QUADRUPLE 3-STATE BUFFERS 74LVC125A
QUADRUPLE 3-STATE BUFFERS Description Pin Assignments The provides four independent buffers with three state outputs. Each output is independently controlled by an associated output enable pin (OE) which
More informationA product Line of Diodes Incorporated. Description. Applications. Truth Table. Note: 1. IEC
2:1 Mux/DeMux Gigabit Ethernet LAN Switch with Power-down Mode Features 1:2 Gigabit LAN Switch Power-down support Low bit-to-bit skew: 200ps Very Low Crosstalk: 75dB @ 250MHz Status Indicator LEDs Switched
More informationPI6C49X0204B Low Skew, 1-TO-4 LVCMOS/LVTTL Fanout Buffer Features Description Block Diagram Pin Assignment
Low Skew, 1-TO-4 LVCMOS/LVTTL Fanout Buffer Features Four LVCMOS / LVTTL outputs LVCMOS / LVTTL clock input CLK can accept the following input levels: LVCMOS, LVTTL Maximum output frequency: Additive phase
More informationPI90LV01/PI90LVB01. Features ÎMeets Î or Exceeds ANSI TIA/EIA Standard ÎSignaling Î rates up to 660 Mbps
SOTiny LVDS High-Speed Differential Line Driver Features ÎMeets Î or Exceeds ANSI TIA/EIA-644-1955 Standard ÎSignaling Î rates up to 660 Mbps ÎBus-Terminal Î ESD exceeds 2kV ÎLow-Voltage Î Differential
More information1 2 3 D D C B GND V CCA V CCB. CSP-12 (Bottom View) Description. Features. Pin Configuration PI4ULS5V104
4-Bit Bi-directional Level Shifter with Automatic Direction Controller Features Description Pin Configuration 1 2 3 D C B D C B A 1 2 3 B4 GND A4 B3 OE A3 B2 CCA A2 B1 CCB A1 A1 A2 A3 A4 NC 2 3 4 5 6 RGY
More informationFeatures. Description. Pin Configuration PT7M CL/CH/NL. Low Power Voltage Detector
Low Power Voltage Detector Features Highly accurate: 1.5% (25 C) Low power consumption: 1μA @ 3.6V Vcc Detect voltage range: 1.8 to 5V in 100mV increments Operating voltage range: 1.2V ~ 5.5V Operating
More informationFeatures. Description PI6ULS5V9515A
I2C Bus/SMBus Repeater Features 2 channel, bidirectional buffer I 2 C-bus and SMBus compatible Operating supply voltage range of 2.3 V to 3.6 V Active HIGH repeater enable input Open-drain input/outputs
More informationDescription. Applications. Truth Table
3.3V, PCI Express 3.0, 1-Lane, 2-Channel, 8Gbps, 2:1 Mux/DeMux Switch w/ Single Enable Features ÎÎ2 Differential Channel, 2:1 Mux/DeMux ÎÎPCI Express 3.0 performance, 8.0Gbps ÎÎBi-directional operation
More informationDescription. Features. Pin Assignment. Function Block Diagram. Pin Description PI4ULS5V102
PI4ULS5102 2-Bit Universal Bi-directional Level Shifter with Automatic Direction Control & Advance Package Solution Features 1.2 to 3.6 on A Port and 1.65 to 5.5 on B Port (CCA CCB) CC Isolation Feature
More information74LVCE1G126 SINGLE BUFFER GATE WITH 3-STATE OUTPUT. Pin Assignments. Description NEW PRODUCT. Features. Applications
Description Pin Assignments The is a single non-inverting buffer/bus driver with a 3-state output. The output enters a high impedance state when a LOW-level is applied to the output enable (OE) pin. The
More informationPI3C V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch
2.5V/3., High Bandwidth, Hot Insertion Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth (>400 MHz) Permits Hot Insertion. Rail-to-Rail, 3. or 2.5V ing 5V I/O
More informationPI5C3384 PI5C3384C PI5C32384 (25Ω)
PI5C3384 PI5C3384C PI5C32384 (25Ω) 0-Bit, 2-Port Bus Switch Features: Near-Zero propagation delay Low noise, 25Ω version (PI5C32384) 5Ω switches connect inputs to outputs (PI5C3384) Direct bus connection
More informationDescription. Applications
2:1 MIPI 4-Data Lane Switch Features ÎÎ4-lane, 2:1 switches that support DHY ÎÎData rate: 2. Gbps ÎÎSupports 2:1 clock differential signal ÎÎ-3 db Bandwidth: 4. GHz Typical ÎÎLow Crosstalk: -30 db@1.2
More information74LVC08A. Description. Pin Assignments. Features. Applications QUADRUPLE 2-INPUT AND GATES 74LVC08A. (Top View) Vcc 4B 4A 4Y 3B 3A 3Y
QUADRUPLE 2-INPUT AND GATES Description Pin Assignments The provides four independent 2-input AND gates. The device is designed for operation with a power supply range of 1.65V to 5.5V. The inputs are
More informationPI5C16861 PI5C (25Ω) 20-Bit, 2-Port Bus Switch
PI5C8 PI5C28 (25Ω) Features Near-Zero propagation delay 5Ω or 25Ω switches connect inputs to outputs Direct bus connection when switches are ON 32X384 function with flow through pinout make board layout
More informationPin Configuration. Pin Description PT7M (CL/CH /NL) Name Type Description. Voltage Detector with Adjustable Delay Time
Voltage Detector with Adjustable Delay Time Features Operate from VCC of 1.2V to 5.5V Capacitor-Adjustable Delay Active-High/-Low Output Options Open-Drain /Push-Pull Output Options Detect Voltage Threshold
More information74HCT138. Description. Pin Assignments. Features. Applications 3 TO 8 LINE DECODER DEMULTIPLEXER 74HCT138
3 TO 8 LINE DECODER DEMULTIPLEXER Description Pin Assignments The is a high speed CMOS device that is designed to be pin compatable with 74LS low power Schottky types. The device accepts a three bit binary
More informationPI3CH Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching
More information74LVCE1G00 SINGLE 2 INPUT POSITIVE NAND GATE. Description. Pin Assignments NEW PRODUCT. Features. Applications
Description Pin Assignments The is a single 2-input positive NAND gate with a standard totem pole output. The device is designed for operation with a power supply range of 1.4V to 5.5V. The inputs are
More informationPin Configuration Pin Description PI4MSD5V9540B. 2 Channel I2C bus Multiplexer. Pin No Pin Name Type Description. 1 SCL I/O serial clock line
2 Channel I2C bus Multiplexer Features 1-of-2 bidirectional translating multiplexer I2C-bus interface logic Operating power supply voltage:1.65 V to 5.5 V Allows voltage level translation between 1.2V,
More informationPI5C3253. Dual 4:1 Mux/DeMux Bus Switch
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2µA typical) Ideally suited for notebook applications
More informationFeatures. Description. Pin Description. Pin Configuration PI6ULS5V9517A. MSOP-8 and SOIC-8. UQFN1.6x1.6-8L(Top view) DFN2x3-8L(Top view)
Level Translating I2C Bus/SMBus Repeater Features 2 channel, bidirectional buffer I 2 C-bus and SMBus compatible Port A operating supply voltage range of 0.8 V to 5.5 V Port B operating supply voltage
More informationPI5C3384 PI5C3384C. 10-Bit, 2-Port Bus Switch
PI5C3384 PI5C3384C 0-Bit, 2-Port Bus Switch Features: Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power (0.2μA typical)
More informationPI3USB221. Features. Applications. Pin Configuration. TDFN Package (Top View) A product Line of Diodes Incorporated
High-peed UB2.0 1:2 Multiplexer/eMultiplexer witch with ignal Enable Features V Operation at 2.5 V and 3.3 V V I/O Accepts ignals up to 5.5 V 1.8-V Compatible Control-Pin Inputs Low-Power Mode When OE
More informationPI3CH200 2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail
More informationPI3HDMI1210-A. Pin Description. Block Diagram. A product Line of. Diodes Incorporated
High-performance HDMI TM Signal Switch w/ Integrated Side-band Signal Support Features 4-Differential Channel 2:1 Mux/DeMux + 2-Channel 2:1 Mux/DeMux Deep Color TM Support Data Rate: 4.0Gbps for high data
More informationDescription. Applications
μp Supervisor Circuits Features Precision supply-voltage monitor - 4.63V (PT7A7511, 7521, 7531) - 4.38V (PT7A7512, 7522, 7532) - 3.08V (PT7A7513, 7523, 7533) - 2.93V (PT7A7514, 7524, 7534) - 2.63V (PT7A7515,
More informationPI4ULS3V Mb/s Bi-directional Level Translator for Push-Pull Applications Features Description Applications Pin Description Pin Configuration
140Mb/s Bi-directional Level Tralator for Push-Pull Applicatio Features Description Applicatio Pin Configuration UDFN1.2*1.6-8L(Top View) Pin Description Pin No. Pin Name Type 1 V CC(A) Power 2 A1 I/O
More informationPI5C Bit Bus Switch with Individual Enables A 1 B 1 GND. Features. Description. Pin Configuration. Block Diagram.
2-Bit Bus Switch with Individual Enables Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2μA typical)
More information( Top View ) OUT1 OUT2 OUT3 OUT4 IN1 IN2 IN3 IN4 IN5 IN6 OUT5 OUT6 OUT7 GND COM ULN2003V12, ULN2003F12. Description. Pin Assignments.
Multi-Channel Relay and Inductive Load Sink Driver Description Pin Assignments The ULN2003V2 and ULN2003F2 are multi-channel sink drivers comprised of 7-channel and 4-channel output stages respectively.
More informationDescription IA 3 IA 2 IA 1 GND. Truth Table (1) H X X Hi-Z Disable S 0-1. L L L I0 S1-0 = 0 L L H I1 S1-0 = 1 Y A to Y B
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (300MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply 2.5V and 3.3V supply voltage
More informationPI3CH360 3-Channel 2:1 Mux/DeMux, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching - 0 to 5V switching
More informationPI5C Bit, 2-Port Bus Switch. Features. Description. Pin Configuration. Block Diagram. Pin Description. Truth Table (1) Pin Name Description
Features ÎÎNear-Zero propagation delay ÎÎ5-ohm switches connect inputs to outputs ÎÎDirect bus connection when switches are on ÎÎUltra Low Quiescent Power (0.2μA typical) Ideally suited for notebook applications
More informationCBT bit 1-of-2 multiplexer/demultiplexer with precharged outputs and Schottky undershoot protection for live insertion
INTEGRATED CIRCUITS 16-bit 1-of-2 multiplexer/demultiplexer with precharged outputs and Schottky undershoot protection for live insertion 2000 Jul 18 FEATURES 5 Ω typical r on Pull-up on B ports Undershoot
More informationPI3V312. Low On-Resistance, 3.3V High-Bandwidth 4-Port, 2:1 Mux/DeMux VideoSwitch. Features. Description. Block Diagram. Pin Configuration S 1 Y A 4
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (500MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply 1.8V, 2.5V and 3.3V supply
More informationAZV358. Pin Assignments. Description DATA SHEET. Applications. Features. Functional Block Diagram. A Product Line of. Diodes Incorporated
DUAL LOW VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS Description Pin Assignments The is dual low voltage (2.7V to 5.5V) operational amplifiers which have rail-to-rail output swing capability. The
More informationAS339/339A. Description. Pin Assignments. Features. Applications LOW POWER LOW OFFSET VOLTAGE QUAD COMPARATORS AS339/339A
LOW POWER LOW OFFSET VOLTAGE QUAD COMPARATORS Description Pin Assignments The consist of four independent precision voltage comparators with a typical offset voltage of 2.0mV and high gain. They are specifically
More informationPI5C32X384/32X384C. 20-Bit, 2-Port Bus Switch. Features. Description. Pin Configuration. Block Diagram. Pin Description
PI5C32X384/32X384C Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power 32X384 (0.2µA typical) Ideally suited
More information74LVC2G00. Pin Assignments. Description NEW PRODUCT. Features. Applications DUAL 2-INPUT NAND GATE 74LVC2G00. (Top View) VCC GND
DUAL 2-INPUT NAND GATE Description Pin Assignments The is a dual, two input NAND gate. Both gates have push-pull outputs designed for operation over a power supply range of 1.65 to 5.5. The device is fully
More informationIN1 GND IN0. Applications
Description Pin Assignments The is a single 3-input positive configurable multiple function gate with a standard push-pull output. The output state is determined by eight patterns of 3-bit input. The user
More informationAS393/393A. Description. Pin Assignments. Features. Applications. Typical Applications Circuit LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS
LOW POWER LOW OFFSET VOLTAGE DUAL COMPARATORS Description Pin Assignments The consist of two independent precision voltage comparators with a typical offset voltage of 1.0mV and high gain. They are specifically
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationApplications AP7350 GND
150mA ULTRA-LOW QUIESCENT CURRENT LDO with ENABLE Description The is a low dropout regulator with high output voltage accuracy. The includes a voltage reference, error amplifier, current limit circuit
More informationAN431. Pin Assignments. Description. Features. Applications. Typical Applications Circuit. A Product Line of. Diodes Incorporated
ADJUSTABLE PRECISION SHUNT REGULATORS Description The series ICs are three-terminal adjustable shunt regulators with guaranteed thermal stability over a full operation range. These ICs feature sharp turn-on
More informationFeatures. Description. Functional Block Diagram. Applications. Pin Assignment PI3A6386. USB Type-C Ultra-Low-THD Audio and Data Switch Array
USB Type-C Ultra-Low-THD Audio and Data Switch Array Features Description : Functional Block Diagram Applications Pin Assignment Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS),
More informationGreen. Case Material: Molded Plastic. UL Flammability Classification 3.3V - 200V Nominal Zener Voltage Range
Green 3.W SURFACE MOUNT POWER ENER DIODE Features Mechanical Data 3.W Power Dissipation Case: SMB Ideally Suited for Automated Assembly Case Material: Molded Plastic. UL Flammability Classification 3.3V
More informationFeatures. Product Marking Reel Size (inch) Tape Width (mm) Quantity per Reel DGD2103MS8-13 DGD2103M ,500
HALF-BRIDGE GATE DRIVER IN SO-8 Description The is a high-voltage / high-speed gate driver capable of driving N-channel MOSFETs and IGBTs in a half-bridge configuration. High voltage processing techniques
More informationFeatures. Part Number Marking Reel Size (inches) Tape Width (mm) Quantity Per Reel DGD2101MS8-13 DGD ,500
HIGH-SIDE AND LOW-SIDE GATE DRIVER IN SO-8 (Type TH) Description The is a high-voltage / high-speed gate driver capable of driving N-Channel MOSFETs and IGBTs in a high-side/low-side configuration. High-voltage
More information74LVC2G125. Description. Pin Assignments. Features. Applications DUAL BUFFER GATE WITH 3-STATE OUTPUTS 74LVC2G125. (Top View) 1OE VCC 2OE GND
DUAL BUFFER GATE WITH 3-STATE OUTPUTS Description Pin Assignments The is a dual buffer gate with 3-state outputs. The (Top iew) device is designed for operation over a power supply range of 1.65 to 5.5.
More informationFeatures. Product Marking Reel Size (inches) Tape Width (mm) Quantity per Reel DGD21844S14-13 DGD ,500
HALF- BRIDGE GATE DRIVER IN SO-14 Description The is a high voltage / high speed gate driver capable of driving N-Channel MOSFETs and IGBTs in a half bridge configuration. High voltage processing techniques
More informationFeatures. Product Marking Reel Size (inches) Tape Width (mm) Quantity per Reel DGD2304S8-13 DGD ,500
HALF-BRIDGE GATE DRIVER IN SO-8 Description Features The is a high voltage / high speed gate driver capable of driving N-channel MOSFETs and IGBTs in a half bridge configuration. High voltage processing
More informationAL5811. Description. Pin Assignments. Features. Applications. Typical Applications Circuit. (Top View) V CC LED GND R SET 3 U-DFN
6V, LINEAR 75mA ADJUSTABLE CURRENT LED DRIVER Description Pin Assignments The is a Linear LED driver with an adjustable LED current up to 75mA offering excellent temperature stability and output handling
More informationAL5816Q. Description. Pin Assignments. Applications. Features VCC PWM GND AUTOMOTIVE COMPLIANT 60V LINEAR LED CONTROLLER AL5816Q
AUTOMOTIVE COMPLIANT 60V LINEAR LED CONTROLLER Description Pin Assignments The is a 5-terminal adjustable constant current linear LED controller offering excellent temperature stability and current (Top
More informationPI5C3253. Dual 4:1 Mux/DeMux Bus Switch
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON ESD Protection up to 2kV HBM Ultra Low Quiescent Power (0.2μA typical) Ideally suited
More informationPI3CH360. Low Voltage, High-Bandwidth, 3-Channel 2:1 Mux/DeMux, NanoSwitch. Features. Description. Block Diagram. Pin Configuration.
Low Voltage, High-Bandwidth, 3-Channel 2:1 Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching 5V I/O tolerant
More informationPI5L200. Description. Features. Pin Configuration. Applications. Block Diagram. Pin Description. Truth Table. A product Line of. Diodes Incorporated
Precision Wide Bandwidth Lanwitch Quad 2:1 Mux/DeMux Features ingle 3.3V/5V supply operation Rail-To-Rail Operation Very Low Distortion: 2% Replaces mechanical relays High-performance, low-cost solution
More informationSBR5E45P5. Features and Benefits. Product Summary A = +25 C) Description and Applications. Mechanical Data. Ordering Information (Note 4)
Green 5A SBR SUPER BARRIER RECTIFIER Product Summary (@T A = +25 C) Features and Benefits ADVANCED NEW NEW INFORMATION V RRM (V) I O (A) V F(MAX) (V) I R(MAX) (ma) 45 5 0.6 0.28 Description and Applications
More informationAP1688. Description. Features NEW PRODUCT. Pin Assignments. Applications. Typical Applications Circuit. A Product Line of. Diodes Incorporated
AC/DC, HIGH PF, HIGH EFFICIENCY, UNIVERSAL MAINS LED DRIVER CONTROLLER Description The is a high performance AC/DC PFC and constant current controller for universal mains LED driver applications. The device
More informationFeatures. Part Number Marking Reel Size (inches) Tape Width (mm) Quantity per Reel DGD2005S8-13 DGD
HIGH-SIDE AND LOW-SIDE GATE DRIVER IN SO-8 Description The is a mid-voltage/high-speed gate driver capable of driving N-channel MOSFETs in a half-bridge configuration. Highvoltage processing techniques
More informationPAM2861. Description. Pin Assignments. Features. Applications. A Product Line of. Diodes Incorporated 1A LED DRIVER WITH INTERNAL SWITCH PAM2861
1A LED DRIVER WITH INTERNAL SWITCH Description Pin Assignments The is a continuous mode inductive step-down converter, designed for driving single or multiple series connected LEDs efficiently from a voltage
More informationPart Number Case Packaging DMN2990UFO-7B X2-DFN k/Tape & Reel
20V N-CHANNEL ENHANCEMENT MODE MOSFET Product Summary Features and Benefits BV DSS 20V R DS(ON) max I D max T A = +25 C 0.99Ω @ V GS = 4.5V 750mA.2Ω @ V GS = 2.5V 680mA.8Ω @ V GS =.8V 555mA 2.4Ω @ V GS
More information74LVC273A. Description. Pin Assignments NEW PRODUCT. Features. Applications OCTAL D-TYPE FLIP-FLOP WITH CLEAR 74LVC273A
OCTAL D-TYPE FLIP-FLOP WITH CLEAR Description The provides eight positive-edge-triggered D-type flipflops with a direct clear (CLR) input. Pin Assignments The device is designed for operation with a power
More informationFeatures. Applications
1.5A ULTRA LOW DROPOUT LINEAR REGULATOR Description The is low dropout three-terminal regulator with a typical dropout of 375mV at 1.5A output current. The provides current limit and thermal shutdown.
More informationAP4310A. Pin Assignments. Description. Features. Applications. Typical Applications Circuit. A Product Line of. Diodes Incorporated
DUAL OP AMP AND VOLTAGE REFERENCE Description The is a monolithic IC specifically designed to regulate the output current and voltage levels of switching battery chargers and power supplies Pin Assignments
More information74AUP2G34. Pin Assignments. Description ADVANCED INFORMATION. Features. Applications. (Top View) SOT363 X2-DFN X2-DFN X2-DFN1010-6
DUAL BUFFERS Description The Advanced Ultra Low Power (AUP) CMOS logic family is designed for low power and extended battery life in portable applications. The is composed of two buffers with standard
More informationFeatures. Gate. G C E Emitter. Product Marking Quantity DGTD65T50S1PT DGTD65T50S1 450 per Box in Tubes (Note 5)
650V FIELD STOP IGBT IN TO-247 Description The is produced using advanced Field Stop Trench IGBT Technology, which provides excellent quality and high-switching performance. Features High-Speed Switching
More informationPackage Pin Out Configuration. Part Number Compliance Marking Reel Size (inch) Tape Width (mm) Quantity per Reel UMC4NQ-7 Automotive NP ,000
YM DUAL COMPLEMENTARY PRE-BIASED TRANSISTORS Features Ultra-Small Surface Mount Package Surface Mount Package Suited for Automated Assembly Simplifies Circuit Design and Reduces Board Space Totally Lead-Free
More information74LVT245BB. Pin Assignments. Description NEW PRODUCT. Applications. Features 3.3 V OCTAL BUS TRANSCEIVER WITH 3 STATE OUTPUTS 74LVT245BB
3.3 V OCTAL BUS TRANSCEIVER WITH 3 STATE OUTPUTS Description Pin Assignments The is an octal transceiver designed for asynchronous communication between data buses. The device transmits data from the A
More informationNOT RECOMMENDED FOR NEW DESIGN USE AP2127N/K/
300mA ADJUSTABLE HIGH PSRR CMOS LINEAR REGULATOR Description Pin Assignments The is a positive, adjustable linear regulator. It features low quiescent current (65µA typ.) and low dropout voltage, making
More informationFST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
More informationFeatures. Typical Configuration ZXGD3113W6. Top View Pin-Out
SYNCHRONOUS MOSFET CONTROLLER IN Description The is intended to drive a MOSFET configured as an ideal diode replacement. The device is comprised of a differential amplifier detector stage and high current
More informationPAM3112. Description. Pin Assignments. Features. Applications. Typical Applications Circuit NOT RECOMMENDED FOR NEW DESIGN USE AP2127
300mA CMOS LINEAR REGULATOR Description The regulator features low quiescent current (65µA Typ) and excellent line/load regulation, making it ideal for battery powered applications. The output voltage
More informationDGD Features. Description. Mechanical Data. Applications. Ordering Information (Note 4) Marking Information YYWW DGD05463
HIGH FREQUENCY HALF-BRIDGE GATE DRIVER WITH PROGRAMMABLE DEADTIME IN W-DFN3030-10 (Type TH) Description The is a high-frequency half-bridge gate driver capable of driving N-channel MOSFETs in a half-bridge
More information1 OE 1D 2D 2Q 3Q 3D 4D 4Q GND 10
OCTAL D-TYPE FLIP-FLOP WITH 3 STATE OUTPUTS Description The provides eight edge-triggered D-type flip-flops featuring 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance
More informationDescription. Features. Pin Configuration. Pin Description PI4MSD5V9546A. 4 Channel I2C bus Switch with Reset
4 Channel I2C bus Switch with Reset Features Description 1-of-4 bidirectional translating multiplexer I2C-bus interface logic Operating power supply voltage:1.65 V to 5.5 V Allows voltage level translation
More informationZTL431AQ, ZTL431BQ ZTL432AQ, ZTL432BQ. Pin Assignments. Description. Features. Typical Application. Applications
AUTOMOTIVE COMPLIANT ADJUSTABLE PRECISION SHUNT REGULATOR Description The ZTL431AQ, ZTL431BQ, ZTL432AQ and ZTL432BQ are three terminal adjustable shunt regulators offering excellent temperature stability
More informationADC114YUQ. Mechanical Data. Features. Ordering Information (Notes 4 & 5) Marking Information NXX 1Y7 YM NXX YM
NXX YM NPN PRE-BIASED SMALL SIGNAL DUAL SURFACE MOUNT TRANSISTOR Features Mechanical Data Epitaxial Planar Die Construction Built-In Biasing Resistors Totally Lead-Free & Fully RoHS Compliant (Notes &
More informationFST Bit Low Power Bus Switch
FST3384 10-Bit Low Power Bus Switch General Description The Fairchild Switch FST3384 provides 10 bits of highspeed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to
More informationDGD Ordering Information (Note 4) Marking Information YYWW DGD05473 HIGH FREQUENCY HIGH-SIDE AND LOW-SIDE GATE DRIVER IN W-DFN
HIGH FREQUENCY HIGH-SIDE AND LOW-SIDE GATE DRIVER IN W-DFN3030-10 Description The is a high-frequency gate driver capable of driving N- channel MOSFETs. The floating high-side driver is rated up to 50V.
More informationGreen. Top View Pin Diagram Internal Schematic. Part Number Case Packaging MSB12M-13 MSB 3,000/Tape & Reel
Green.2A SURFACE MOUNT GLASS PASSIVATED BRIDGE RECTIFIER Product Summary (@T A = +25 C) V RRM (V) I O (A) V F (V) I R (µa),000.2. 5 Features and Benefits Glass Passivated Die Construction Compact, Thin
More informationV CC RESET. Applications
MICRO POWER VOLTAGE DETECTOR Description Pin Assignments The is brand new micro-power voltage detector series developed by Diodes Inc. with target to be used for microprocessor (µp) supervisory circuits
More informationFeatures. Drain SOT23 D. Gate. Source. Part Number Case Packaging DMG3414UQ-7 SOT23 3,000/Tape & Reel DMG3414UQ-13 SOT23 10,000/Tape & Reel
N-CHANNEL ENHANCEMENT MODE MOSFET Product Summary Features V (BR)DSS 2V Description R DS(ON) max 25mΩ @ V GS = 4.5V I D max T A = +25 C 9A 29mΩ @ V GS = 2.5V 5.5A 37mΩ @ V GS = 1.8V 4.8A This MOSFET is
More informationGreen. Features DO-214AC
Green SCHOTTKY BARRIER RECTIFIERS Product Summary V RRM (V) I O (A) V F (MAX) (V) I R (MAX) (ma) @ +25 C @ +25 C 40 3 0.5 0.5 Description The is a low voltage dual Schottky rectifier suited for switch
More informationGreen. Features. Equivalent Circuit. Top View Pin Out Configuration. Part Number Case Packaging DMTH10H005SCT TO220AB 50 Pieces/Tube
Green V +75 C N-CHANNEL ENHANCEMENT MODE MOSFET Product Summary R DS(ON) I D T C = +25 C V 5mΩ @V GS = V 4A BV DSS Description This new generation MOSFET features low on-resistance and fast switching,
More informationAP4320. Description. Pin Assignments. Features. Applications. Typical Applications Circuit. A Product Line of. Diodes Incorporated
CONSTANT OLTAGE AND CONSTANT CURRENT CONTROLLER Description The is a highly integrated solution for a constant voltage/constant current mode SMPS application. Pin Assignments (Top iew) The contains one.
More informationB3XXAE B320AE-B345AE. Product Summary. Features and Benefits. Mechanical Data. Description and Applications NEW PRODUCT. Ordering Information (Note 4)
Green 3.0A SCHOTTKY BARRIER RECTIFIER Product Summary B320AE/B330AE/B340AE/B345AE V RRM (V) I O (A) V F(MAX) (V) I R(MAX) (ma) @ +25 C @ +25 C 20 3 0.5 0. 30 3 0.5 0.15 40 3 0.5 0.20 45 3 0.5 0.30 Features
More informationAS431H. Description. Pin Assignments NEW PRODUCT. Features. Applications ADJUSTABLE PRECISION SHUNT REGULATORS AS431H ANODE CATHODE ANODE CATHODE REF
ADJUSTABLE PRECISION SHUNT REGULATORS Description Pin Assignments The is a three-terminal adjustable shunt regulator with guaranteed thermal stability over a full operation range. It features sharp turn-on
More informationAP4305. Description. Pin Assignments. Features. Applications. Typical Applications Circuit AP4305. A Product Line of. Diodes Incorporated
CONSTANT OLTAGE AND CONSTANT CURRENT CONTROLLER Description Pin Assignments The is a highly integrated solution for a constant voltage/constant current mode SMPS application. (Top iew) The contains one
More information