PI5L200. Description. Features. Pin Configuration. Applications. Block Diagram. Pin Description. Truth Table. A product Line of. Diodes Incorporated

Transcription

1 Precision Wide Bandwidth Lanwitch Quad 2:1 Mux/DeMux Features ingle 3.3V/5V supply operation Rail-To-Rail Operation Very Low Distortion: 2% Replaces mechanical relays High-performance, low-cost solution for switching between different LAN signals Low crosstalk: 30 Mbps Low insertion loss and On-Resistance: 6-ohms typical Off isolation: 30 Mbps Wide bandwidth data rates >135 Mbps Low Quiescent upply Current (100nA typical) Packaging (Pb-free & Green available): 16-pin 150-mil wide plastic QOP (Q) 16-pin 150-mil wide plastic OIC (W) 16-pin 173-mil wide plastic TOP (L) Applications 10/100 Base-TX/T4 100VG-AnyLAN Token Ring 4/16 Mbps ATM25 NIC Adapter and Hubs ONT OCI 51.8Mbps T1/1 Description Diodes' is a Rail-to-Rail Quad 2:1 multiplexer/demultiplexer Lanwitch with 3-state outputs. The On-Resistance typically varies from 5 ohms to 7 ohms with data inputs of 0V to 5V. Generally, this part can be used to replace mechanical relays in low voltage (3.3V/5V systems) LAN applications. With a wide bandwidth of 135 MHz, the can switch Fast thernet and ATM25 signals. Into 100-ohm UTP cables, the switch distortion is typically less than two percent. MHz is 70dB. The operates from a single 3.3V/5V supply and interface to TTL logic. Pin Configuration IA0 IA1 YA IB0 IB1 YB GND VCC ID0 ID1 YD IC0 IC1 YC Block Diagram IA0 IA1 YA Pin Description Pin Name IAn-IDn Description Data Inputs elect Inputs IB0 IB1 YB YA-YD nable Data Outputs IC0 IC1 YC GND V CC Ground Power ID0 ID1 YD Truth Table YA YB YC YD Function H X Hi-Z Hi-Z Hi-Z Hi-Z Disable L L IA 0 I B 0 I C 0 I D 0 = 0 Decoder/Driver L H IA 1 I B 1 I C 1 I D 1 = 1 Note: H = High Voltage Level, L = Low Voltage Level, witches are shown with logic "0" input (elect and nable) 1

2 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) torage Temperature C to +150 C Ambient Temperature with Power Applied C to +85 C upply Voltage to Ground Potential V to +7.0V DC Input Voltage V to V CC +0.5V DC Output Current ma Power Dissipation W Note: tresses greater than those listed under MAXIMUM RAT- ING may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. xposure to absolute maximum rating conditions for extended periods may affect reliability. ingle 5.0V upply DC lectrical Characteristics (Over the Operating Range, T A = -40 C to +85 C, V CC = 5V ±10%, GND = 0V) Parameters Description Test Conditions (1) Min. Typ. (2) Max. Units V ANALOG Analog ignal Range 0 - V CC V R ON ON-Resistance I ON = 10mA to 30mA R ON Match Between Channels Ω R FLAT(ON) R ON Flatness I ON = 1mA, V NO, V NC = 0V to 5V I NO(OFF), I NO(ON) On/Off Leakage Current V NO, V NC = 4.5V na I CC Quiescent upply Current V CC = 5.5V, V IN = 0V or V CC µa I O Output Current V NO, V NC or V COM = 0V to 5V ma V IH Input HIGH Voltage Guaranteed Logic HIGH Level V IL Input LOW Voltage Guaranteed Logic LOW Level V I IH Input HIGH Current V CC = Max., V IN = V CC - - ±1 I IL Input LOW Current V CC = Max., V IN = GND - - ±1 µa Dynamic lectrical Characteristics (Over the Operating Range, T A = -40 C to +85 C, V CC = 5V ±10%, GND = 0V) Parameters Description Test Conditions (1) Min. Typ. (2) Max. Units t ON Turn-on Time V ON or V NC = 3.0V, see Fig t OFF Turn-off Time V ON or V NC = 3.0V, see Fig X TALK Crosstalk R L = 100 ohms, f = 30 MHz, see Fig db C (OFF) NC or NO Capacitance f = 1 khz pf O IRR Off Isolation R L = 100 ohms, f = 30 MHz, see Fig db BW Bandwidth -3dB R L = 100 ohms, see Fig MHz D Distortion DR ON /RL R L = 100 ohms % Note: 1. For Max. or Min. conditions, use appropriate value specified under lectrical Characteristics for applicable device type. 2. Guaranteed by design. ns 2

3 ingle 3.3V upply DC lectrical Characteristics (Over the Operating Range, T A = -40 C to +85 C, V CC = 3.3V ±10%, GND = 0V) Parameters Description Test Conditions (1) Min. Typ. (2) Max. Units V ANALOG Analog ignal Range 0 - V CC V R ON ON-Resistance I ON = 10mA to 30mA R ON Match Between Channels Ω R FLAT(ON) R ON Flatness I ON = 1mA, V NO, V NC = 0V to 5V I NO(OFF), I NO(ON) On/Off Leakage Current V NO, V NC = 3.0V na I COM(ON) On Leakage Current V NO, V NC = 3.0V µa I O Output Current V NO, V NC or V COM = 0V ma V IH Input HIGH Voltage Guaranteed Logic HIGH Level V IL Input LOW Voltage Guaranteed Logic LOW Level V I IH Input HIGH Current V CC = Max., V IN = V CC - - ±1 I IL Input LOW Current V CC = Max., V IN = GND - - ±1 µa Dynamic lectrical Characteristics (Over the Operating Range, T A = -40 C to +85 C, V CC = 3.3V ±10%, GND = 0V) Parameters Description Test Conditions (1) Min. Typ. (2) Max. Units t ON Turn-on Time V ON or V NC = 1.5V, see Fig t OFF Turn-off Time V ON or V NC = 1.5V, see Fig ns X TALK Crosstalk R L = 50 ohms, f = 1 MHz, see Fig db C (OFF) NC or NO Capacitance f = 1 khz C COM(OFF) COM Off Capacitance f = 1 khz pf O IRR Off Isolation R L = 50 ohms, f = 1 MHz, see Fig db BW Bandwidth -3dB R L = 50 ohms, see Fig MHz D Distortion R L = 100 ohms % Dynamic lectrical Characteristics (Over the Operating Range, T A = -40 C to +85 C, V CC = 3.3V ±10%, GND = 0V) Parameters Description Test Conditions (1) Min. Typ. (2) Max. Units I CC Quiescent Positive Power upply Current V CC = 3.6V, V IN = 0V or V CC All Channesl ON or OFF Note: 1. For Max. or Min. conditions, use appropriate value specified under lectrical Characteristics for applicable device type. 2. Guaranteed by design µa 3

4 TRANMIT TX RX RCIV Figure 1a. Full Duplex Transceiver TX1 120Ω RX1 Test Circuits Figure 1b. Loop Back Figure 1c. Line Termination Figure 1d. Line Clamp Vcc 3V In Vcc Y VOUT DIGITAL INPUT 50% 50% GND 100W 35pF ANALOG OUTPUT t ON 90% 90% t OFF Figure 2. witching Time 4

5 ACTIV PROB HP4195 NTWORK ANALYZR VOUT 50Ω 1 +5V Figure 3. Bandwidth ACTIV PROB HP4195 NTWORK ANALYZR IA0 YA IC0 YA VOUT 50Ω Figure 4. Crosstalk ACTIV PROB HP4195 NTWORK ANALYZR I0 Y VOUT 50Ω I1 50Ω Figure 5. Off Isolation 5

6 RH = TA = 25 C 20 RIN = 1dBm RL = TA = 25 C 0 5V On-Resistance R ON (Ω) V 5V Insertion Loss BW (db) V InputV oltage (V ) -4 1K 1M 10M 100M 1G Frequency (H z) Figure 6. On-Resistance vs. Input Voltage Figure 7. Insertion Loss vs. Frequency PIN = 1dBm TA = 25 C RL = 0 PIN = 1dBm TA = 25 C RL = Off Isolation OIRR (db) V, 5V Crosstalk XTALK (db) V, 5V -90 1M 10M 100M 1G Frequency (Hz) Figure 8. Off Isolation vs. Frequency -80 1M 10M 100M 1G Frequency (Hz) Figure 9. Crosstalk vs. Frequency 6

7 Part Marking Q Package W Package L Package PI5L 200Q ZYWXX PI5L 200W BZYYWWXX PI5L 200L ZYWXX Z: Die Rev Code Y: Year W: Workweek 1st X: Assembly Code 2nd X: Fab Code B: Port Code Z: Die Rev YY: Year WW: Workweek 1st X: Assembly Code 2nd X: Fab Code Z: Die Rev Y: Year W: Workweek 1st X: Assembly Code 2nd X: Fab Code 7

8 Packaging Mechanical: 16-QOP (Q)

9 A product Line of Packaging Mechanical: 16-OIC (W) January 2018

10 Packaging Mechanical: 16-TOP (L) For latest package info. please check: Ordering Information Ordering Code Packaging Code Package Description QX Q 16-pin, 150mil Wide (QOP) WX W 16-pin, 150mil Wide (OIC) LX L 16-pin, 173mil Wide (TOP) Notes: 1. U Directive 2002/95/C (RoH), 2011/65/U (RoH 2) & 2015/863/U (RoH 3) compliant. All applicable RoH exemptions applied. 2. ee for more information about s definitions of Halogen- and Antimony-free, Green and Lead-free. Thermal characteristics can be found on the company web site at 3. = Pb-free and Green 4. X suffix = Tape/Reel 10

11 IMPORTANT NOTIC DIOD INCORPORATD MAK NO WARRANTY OF ANY KIND, XPR OR IMPLID, WITH RGARD TO THI DOCUMNT, INCLUDING, BUT NOT LIMITD TO, TH IMPLID WARRANTI OF MRCHANTABILITY AND FITN FOR A PARTICULAR PURPO (AND THIR QUIVALNT UNDR TH LAW OF ANY JURIDICTION). and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. does not assume any liability arising out of the application or use of this document or any product described herein; neither does convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold and all the companies whose products are represented on website, harmless against all damages. does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. hould Customers purchase or use products for any unintended or unauthorized application, Customers shall indemnify and hold and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United tates, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United tates, international or foreign trademarks. This document is written in nglish but may be translated into multiple languages for reference. Only the nglish version of this document is the final and determinative format released by. LIF UPPORT products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief xecutive Officer of. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by. Further, Customers must fully indemnify and its representatives against any damages arising out of the use of products in such safety-critical, life support devices or systems. Copyright 2016, 11