1 2 3 D D C B GND V CCA V CCB. CSP-12 (Bottom View) Description. Features. Pin Configuration PI4ULS5V104

Transcription

1 4-Bit Bi-directional Level Shifter with Automatic Direction Controller Features Description Pin Configuration D C B D C B A B4 GND A4 B3 OE A3 B2 CCA A2 B1 CCB A1 A1 A2 A3 A4 NC RGY PACKAGE (TOP IEW) CCA 1 CCB B1 B2 B3 B4 NC A CSP-12 (Bottom iew) 7 8 GND NC - No internal connection OE QFN3.5x3.5-14L PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

2 Pin Description Pin Name Description CCA A-port supply voltage 1.2 CCA 3.6 and CCA CCB. A1 Input/output 1. Referenced to CCA. A2 Input/output 2. Referenced to CCA. A3 Input/output 3. Referenced to CCA. A4 Input/output 4. Referenced to CCA. GND Ground OE 3-State output. Pull OE low to place all outputs in 3-state mode. Referenced to CCA. B4 Input/output 4. Referenced to CCB. B3 Input/output 3. Referenced to CCB. B2 Input/output 2. Referenced to CCB. B1 Input/output 1. Referenced to CCB. CCB B-port supply voltage 1.65 CCB 5.5. Maximum Ratings *1 Min. Max. CCA Supply voltage range CCB I Input voltage range A port B port O oltage range applied to any output in the high-impedance or A port power-off state B port O oltage range applied to any output in the high or low state *2 A port -0.5 CCA B port -0.5 CCB I IK Input clamp current, I < ma I OK Output clamp current, O < ma I O Continuous output current - ±50 ma I O Continuous current through CCA, CCB, or GND - ±100 ma T stg Storage temperature range *1 Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. *2 The value of CCA and CCB are provided in the recommended operating conditions table. PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

3 Recommend Operation Conditions (1)(2) Parameter Description CCA CCB Min. Max. CCA Supply voltage CCB IH High-level input voltage Data 1.2 to 1.65 to CCI * inputs (3) CCI 1.2 to 1.65 to OE input CCA * IL Low-level input voltage Data 1.2 to 1.65 to 0 CCI * inputs (3) 1.2 to 1.65 to OE input 0 CCA * O oltage range applied to any output in the A port 1.2 to 1.65 to high-impedance or power-off state B port A port 1.2 to 1.65 to inputs t/ v Input transition rise or fall rate 1.65 to B port 1.2 to ns/ inputs to T A Operating free-air temperature (1) The A and B sides of an unused data I/O pair must be held in the same state, i.e., both at CCI or both at GND. (2) CCA must be less than or equal to CCB and must not exceed 3.6. (3) CCI is the supply voltage associated with the input port. PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

4 DC Electrical Characteristics (1)(2) Parameter Test Conditions CCA CCB I I I off I OZ T A = to 85 Min Typ Max Min Max OHA I OH = -20μA to CCA OLA I OL = 20μA to OHB I OH = -20μA to CCB OLB I OL = 20μA to OE I = CCI or GND 1.2 to to ±1 - ±2 μa A port I or O = 0 to to ±1 - ±2 B port I or O = 0 to to ±1 - ±2 μa A or B port OE = GND 1.2 to to ±1 - ±2 μa I CCA I CCB I CCA + I CCB I CCZA I CCZB I = CCI or GND, Io = 0 I = CCI or GND, Io = 0 I = CCI or GND, Io = 0 I = CCI or GND, Io = 0, OE = GND I = CCI or GND, Io = 0, OE = GND to to to to to to to to to to to to to to to Ci OE to to pf A port Cio to to 5.5 pf B port (1) CCI is the supply voltage associated with the input port. (2) CCO is the supply voltage associated with the output port. μa μa μa μa μa PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

5 AC Electrical Characteristics Timing requirements a. T A = 25, CCA = 1.2 CCB = 1.8 CCB = 2.5 CCB = 3.3 CCB = 5 TYP TYP TYP TYP Data rate Mbps t W Pulse duration Data inputs ns b. T A = 25, CCA = 1.5±0.1 CCB =1.8±0.15 CCB =2.5±0.2 CCB =3.3±0.3 CCB =5±0.5 MIN MAX MIN MAX MIN MAX MIN MAX Data rate Mbps t W Pulse duration Data inputs ns c. T A = 25, CCA = 1.8±0.15 CCB =1.8±0.15 CCB =2.5±0.2 CCB =3.3±0.3 CCB =5±0.5 MIN MAX MIN MAX MIN MAX MIN MAX Data rate Mbps t W Pulse duration Data inputs ns d. T A = 25, CCA = 2.5±0.2 CCB =2.5±0.2 CCB =3.3±0.3 CCB =5±0.5 MIN MAX MIN MAX MIN MAX Data rate Mbps t W Pulse duration Data inputs ns e. T A = 25, CCA = 3.3±0.3 CCB =3.3±0.3 CCB =5±0.5 MIN MAX MIN MAX Data rate Mbps t W ns Switching characteristics a. T A = 25, CCA = 1.2 Parameter From To CCB =1.8 CCB =2.5 CCB =3.3 CCB =5 (INPUT) (OUTPUT) TYP TYP TYP TYP t pd A B B A ns t en OE A B t dis OE A B t ra, t fa A-port rise and fall ns t rb, t fb B-port rise and fall ns t SK(O) Channel-to-channel skew ns Max data rate Mbps PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

6 b. T A = 25, CCA = 1.5±0.1 Parameter From To CCB =1.8±0.15 CCB = 2.5±0.2 CCB =3.3±0.3 CCB = 5±0.5 (INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX MIN MAX t pd A B B A ns t en OE A B t dis OE A B t ra, t fa A-port rise and fall ns t rb, t fb B-port rise and fall ns t SK(O) Channel-to-channel skew ns Max data rate Mbps c. T A = 25, CCA = 1.8±0.15 Parameter From To CCB =1.8±0.15 CCB =2.5±0.2 CCB =3.3±0.3 CCB =5±0.5 (INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX MIN MAX t pd A B B A ns t en OE A B t dis OE A B t ra, t fa A-port rise and fall ns t rb, t fb B-port rise and fall ns t SK(O) Channel-to-channel skew ns Max data rate Mbps d. T A = 25, CCA = 2.5±0.2 Parameter From To CCB =2.5±0.2 CCB =3.3±0.3 CCB =5±0.5 (INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX t pd A B B A ns t en OE A B t dis OE A B t ra, t fa A-port rise and fall ns t rb, t fb B-port rise and fall ns t SK(O) Channel-to-channel skew ns Max data rate Mbps PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

7 e. T A = 25, CCA = 3.3±0.3 Parameter From To CCB =3.3±0.3 CCB =5±0.5 (INPUT) (OUTPUT) MIN MAX MIN MAX t pd A B B A ns t en OE A B t dis OE A B t ra, t fa A-port rise and fall ns t rb, t fb B-port rise and fall ns t SK(O) Channel-to-channel skew ns Max data rate Mbps Operating Characteristics C pda C pdb C pda C pdb CCA Parameter Test Conditions to 5.5 TYP TYP TYP TYP TYP TYP TYP A-port input, B-port output. C L =0, f=10 MHz, B-port input, A-port output. tr = t f =1ns, A-port input, B-port output. OE= CCA B-port input, A-port output. (outputs enabled) A-port input, B-port output. C L =0, f =10 MHz, B-port input, A-port output. tr = t f =1ns, A-port input, B-port output. OE=GND B-port input, A-port output. (outputs disabled) CCB pf Test Circuit 1> Load circuit for Max data rate, pulse duration propagation delay output rise and fall time measurement From Output Under Test 15pF 1MΩ 2> Load circuit for enable/disable time measurement From Output Under Test 50kΩ S1 2*cco Open TEST tpzl/tplz tphl/tphz S1 2*cco Open 15pF 50kΩ 3> Timing Definitions for Propagation Delays and Enable/Disable Measurement PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

8 4> oltage waveforms pulse duration tw Input CCI/2 CCI/2 CCI 0 5> Notes A. C L includes probe and jig capacitance. B. All input pulses are supplied by generators having the following characteristics: PRR_10 MHz, Z O = 50 W, dv/dt 1 /ns. C. The outputs are measured one at a time, with one transition per measurement. D. t PLH and t PHL are the same as tpd. E. CCI is the CC associated with the input port. F. CCO is the CC associated with the output port. G. All parameters and waveforms are not applicable to all devices. Block Diagram OE A4 Channel 4 B4 A3 Channel 3 B3 A2 Channel 2 B2 A1 Channel 1 B1 PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

9 Principles of operation PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

10 Figure1. Architecture of PI4ULS5104 I/O Cell Figure2. Typical I IN vs. IN Curve Note: A. T is the input threshold voltage of the PI4ULS5104 (typically CCI /2). B. D is the supply voltage of the external driver. PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

11 Mechanical Information TQFN3.5x PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

12 CSP-12 TOP IEW Ordering Information Notes: Part Number Package Code Package PI4ULS5104ZBEX ZB 14-pin, 3.5X3.5 (TQFN) PI4ULS5104GAEX GA 12-pin, 1.37X1.87 Wafer Level (CSP) Thermal characteristics can be found on the company web site at E = Pb-free and Green X suffix = Tape/Reel PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated

13 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more ed States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more ed States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright 2016, Diodes Incorporated PI4ULS September 2017 Document Number DS40173 Rev Diodes Incorporated