PI3C3126. Description. Features. 14-Pin Configuration. Applications. Block Diagram. 16-Pin Configuration. Truth Table (1) Pin Description.
|
|
- Randell Brendan Eaton
- 5 years ago
- Views:
Transcription
1 2./3.3, High Bandwidth, Hot Insertion,4-Bit, 2-Port Bus Switch with Individual Enables Features Near-Zero propagation delay -ohm switches connect inputs to outputs High Bandwidth (>400 MHz) 2./3.3 Supply oltage Operation Rail-to-Rail, or 2. or 3.3 Switching I/O Tolerant Permits Hot Insertion Packaging (Pb-free & Green available): 14-pin 170-mil wide plastic TSSOP (L) 16-pin 10-mil wide plastic QSOP (Q) Applications High Bandwidth Data Switching Hot Docking Block Diagram A0 B0 Description Pericom Semiconductor s is a 2. volt or 3.3 volt, 4-bit bus switch designed with four individual -ohm bus switches with fast indiviual enables in an industry standard 74XX12/126 pinout. When enabled via the associated Bus Enable pin, the A pin is directly connected to the B pin for that particular gate. The bus switch introduces no additional propagation delay or additional ground bounce noise. The has active HIGH enables. It is very useful in switching signals that have high bandwidth (>400 MHz). 14-Pin Configuration BE0 A0 B0 BE1 A1 B1 GND PIN L cc BE3 A3 B3 BE2 A2 B2 BE0 A1 BE1 A2 BE2 A3 BE3 B1 B2 B3 16-Pin Configuration NC BE0 A0 B0 BE1 A1 B1 GND PIN Q cc BE3 A3 B3 BE2 A2 B2 NC Pin Description Pin Name BEn A3 - A0 B3 - B0 CC GND Description Switch Enable Bus A Bus B Power Ground Truth Table (1) BEn An Bn CC Function X Hi-Z Hi-Z GND Disconnect L Hi-Z Hi-Z CC Disconnect H Bn An CC Connect Note: 1. H = High oltage Level, L = Low oltage Level HI-Z = High Impedance, X = Don t Care 1
2 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature... 6 C to +10 C Ambient Temperature with Power Applied C to +8 C Supply oltage to Ground Potential (Inputs & CC Only) to +4.6 Supply oltage to Ground Potential (Outputs & D/O Only) to +4.6 DC Input oltage to +. DC Output Current mA Power Dissipation... 0.W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over Operating Range, TA = 40 C to +8 C, CC = 3.3 ±10%) Parameters Description Test Conditions(1) Min. Typ.(2) Max Units IH Input HIGH oltage Guearanteed Logic HIGH Level 2.0 IL Input LOW oltage Guaranteed Logic LOW Level I IH Input HIGH current CC = Max., IN = CC ±1 I IL Input LOW Current CC = Max., IN = GND ±1 I OZH (3) High Impedance Output Current 0 A, B CC ±1 IK Clamp Diode oltage CC = Min., I IN = 18mA R ON Switch ON Resistance (4) CC = Min., IN = 0.0, I ON = 48mA or 60mA CC = Min., IN = 2.4, I ON = 1mA 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at CC = 3.3, TA = 2 C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins µa Ω Capacitance (TA = 2 C, f = 1 MHz) Parameters (1) Description Test Conditions Typ. Units C IN Input Capacitance IN = 0 3. C OFF A/B Capacitance, Switch Off IN = 0.0 C ON A/B Capacitance, Switch On IN = pf 1. This parameter is determined by device characterization but is not production tested. 2
3 Power Supply Characteristics Parameters Description Test Conditions Min. Typ. (2) Max. Units Quiescent Power I CC Supply Current CC = Max IN = GND or CC Supply Current per µa I CC Input HIGH CC = Max IN = 3.0 (3) For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at CC = 3.3, +2 C ambient. 3. Per driven input (control input only); A and B pins do not contribute to ΔICC. Switching Characteristics over 3.3 Operating Range Parameters Description Conditions t PLH Propogation Delay (1,2) t PHL A to B, B to A C L =0pF R L = 00Ω Min. Com. Max. 0.2 Units t PZH Bus Enable Time t C L =0pF PZL R L = 00Ω t PHZ Bus Disable Time R = 00Ω 1.. t PLZ 1. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.2ns for 0pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. ns Switching Characteristics over 2. Operating Range Parameters Description Conditions t PLH Propogation Delay (1,2) t PHL A to B, B to A C L =0pF R L = 00Ω Min. Com. Max. 0.2 Units t PZH Bus Enable Time t C L =0pF PZL R L = 00Ω t PHZ Bus Disable Time R = 00Ω t PLZ 1. This parameter is guaranteed but not tested on Propagation Delays. 2. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.2ns for 0pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. ns 3
4 4.0 CC O U T ) IN () Switch Output oltage vs. Input oltage over arious Supply oltages 4
5 Packaging Mechanical: 14-Pin TSSOP (L14)
6 Packaging Mechanical: 16-Pin QSOP (Q16) Note: For latest package info, please check: Ordering Information Ordering Code Packaging Code Package Type LE L 14-pin, 173mil Wide (TSSOP) LEX L 14-pin, 173mil Wide (TSSOP), Tape & Reel QE Q 16-pin, 10mil Wide (QSOP) QEX Q 16-pin, 10mil Wide (QSOP), Tape & Reel Thermal characteristics can be found on the company web site at E = Pb-free & Green Adding an X suffix = Tape/Reel 6
PI3C V/3.3V, High Bandwidth, Hot Insertion 8-Bit, 2-Port, Bus Switch. Description. Features. Pin Configuration. Block Diagram.
Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth Operation (>400 MHz) Permits Hot Insertion 5V I/O Tolerant Rail-to-Rail 3.3V or 2.5V Switching 2.5V Supply Voltage
More informationPI3C3125/PI3C3126. Description
.V/.V, High Bandwidth, Hot Insertion,-Bit, -Port Bus Switch with Individual Enables Features Near-Zero propagation delay -ohm switches connect inputs to outputs High Bandwidth (>00 MHz) Rail-to-Rail, or.v
More informationPI5C16861 PI5C (25Ω) 20-Bit, 2-Port Bus Switch
PI5C8 PI5C28 (25Ω) Features Near-Zero propagation delay 5Ω or 25Ω switches connect inputs to outputs Direct bus connection when switches are ON 32X384 function with flow through pinout make board layout
More informationPI3CH Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching
More informationPI3C V/3.3V, High Bandwidth, Hot Insertion 10-Bit, 2-Port, Bus Switch
2.5V/3., High Bandwidth, Hot Insertion Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High Bandwidth (>400 MHz) Permits Hot Insertion. Rail-to-Rail, 3. or 2.5V ing 5V I/O
More informationDescription IA 3 IA 2 IA 1 GND. Truth Table (1) H X X Hi-Z Disable S 0-1. L L L I0 S1-0 = 0 L L H I1 S1-0 = 1 Y A to Y B
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (300MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply 2.5V and 3.3V supply voltage
More informationPI5C3384 PI5C3384C PI5C32384 (25Ω)
PI5C3384 PI5C3384C PI5C32384 (25Ω) 0-Bit, 2-Port Bus Switch Features: Near-Zero propagation delay Low noise, 25Ω version (PI5C32384) 5Ω switches connect inputs to outputs (PI5C3384) Direct bus connection
More informationPI3C3245. Description. Features. Truth Table (1) Pin Description. Pin Name Description. Function BE A0-7. A product Line of. Diodes Incorporated
Pb Lead-free Green A product Line of 2.5V/3.3V, High Bandwidth, Hot Insertion 8-Bit, 2-Port, Bus Switch Features ÎÎNear-Zero propagation delay ÎÎ5-ohm switches connect inputs to outputs ÎÎHigh Bandwidth
More informationPI3CH200 2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail
More informationPI3V312. Low On-Resistance, 3.3V High-Bandwidth 4-Port, 2:1 Mux/DeMux VideoSwitch. Features. Description. Block Diagram. Pin Configuration S 1 Y A 4
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (500MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply 1.8V, 2.5V and 3.3V supply
More informationPI5C3253. Dual 4:1 Mux/DeMux Bus Switch
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2µA typical) Ideally suited for notebook applications
More informationPI3CH360 3-Channel 2:1 Mux/DeMux, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug
1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching - 0 to 5V switching
More informationPI3C3305/PI3C3306. Features. Description. Applications. PI3C3306 Block Diagram. PI3C3305 Block Diagram. PI3C Pin Configuration
2.5V/3., High-Bandwidth, Hot-Insertion, 2-Bit, 2-Port Bus Switch w/ Individual Enables Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High Bandwidth (>400 MHz) Rail-to-Rail,
More informationPI5C Bit, 2-Port Bus Switch. Features. Description. Pin Configuration. Block Diagram. Pin Description. Truth Table (1) Pin Name Description
Features ÎÎNear-Zero propagation delay ÎÎ5-ohm switches connect inputs to outputs ÎÎDirect bus connection when switches are on ÎÎUltra Low Quiescent Power (0.2μA typical) Ideally suited for notebook applications
More informationPI5C32X384/32X384C. 20-Bit, 2-Port Bus Switch. Features. Description. Pin Configuration. Block Diagram. Pin Description
PI5C32X384/32X384C Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power 32X384 (0.2µA typical) Ideally suited
More informationPI5C3384 PI5C3384C. 10-Bit, 2-Port Bus Switch
PI5C3384 PI5C3384C 0-Bit, 2-Port Bus Switch Features: Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power (0.2μA typical)
More informationPI5C Bit Bus Switch with Individual Enables A 1 B 1 GND. Features. Description. Pin Configuration. Block Diagram.
2-Bit Bus Switch with Individual Enables Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2μA typical)
More informationPI3CH360. Low Voltage, High-Bandwidth, 3-Channel 2:1 Mux/DeMux, NanoSwitch. Features. Description. Block Diagram. Pin Configuration.
Low Voltage, High-Bandwidth, 3-Channel 2:1 Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching 5V I/O tolerant
More informationPI3B3125/PI3B3126. Description. Features. A product Line of. Diodes Incorporated. 3.3V, 4-Bit, 2-Port Nanoswitchw/Individual Enables
.V, -Bit, -Port Nanoswitchw/Individual Enables Features ¼¼Near zero propagation delay ¼¼5 Ohm switches connect inputs to outputs ¼¼Fast Switching Speed - ns max. ¼¼Ultra Low Quiescent Power (0.µA Typical)
More informationPI5C3253. Dual 4:1 Mux/DeMux Bus Switch
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Direct bus connection when switches are ON ESD Protection up to 2kV HBM Ultra Low Quiescent Power (0.2μA typical) Ideally suited
More informationPI3B V, Synchronous 16-Bit to 32-Bit FET Mux/DeMux NanoSwitch. Description. Features. Pin Configuration. Block Diagram.
PI363 3.3, Synchronous 6-it to 3-it FET Mux/DeMux NanoSwitch Features Near-Zero propagation delay. Ω Switches Connect etween Two Ports Packaging: - -pin 40mil Wide Thin Plastic TSSOP (A) - -pin 300mil
More informationPI3V314. Low On-Resistance, 3.3V High-Bandwidth 3-Port, 4:1 Mux/DeMux VideoSwitch. Features. Description. Pin Configuration.
3-Port, 4:1 Mux/DeMux VideoSwitch Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (375MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V
More informationFeatures. Description. Pin Configuration. Block Diagram. Truth Table (1) PI3CH480. TSSOP/QSOP Top View. UQFN3x3-16 Top View
4-Channel 2:1 Mux/DeMux, Enable Low 1.8V / 2.5V / 3.3V, High-Bandwidth, Hot Plug Features Near-Zero propagation delay 5-ohm switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond
More informationPI74LPT244. Fast CMOS 3.3V 8-Bit Buffer/Line Driver. Features. Description. Block Diagram. Pin Configuration
Fast CMOS 3.3V 8-Bit Buffer/Line Driver Features Compatible with LCX and LVT families of products Supports 5V Tolerant Mixed Signal Mode Operation Input can be 3V or 5V Output can be 3V or connected to
More informationPO3B10A. Truth Table. High Bandwidth Potato Chip. 2-Channel, 2:1 Mux/DeMux Switch w/ Single Enable GND V DD GND SEL
PO3B0A www.potatosemi.com FEATURES: Patented technology High signal -3db passing bandwidth at 3.5Gbps or.75ghz Near-Zero propagation delay CC =.65 to 3.6 Ultra-Low Quiescent Power: 0.µA typical Ideally
More informationDescription. Features. Application. Pin Assignment. Pin Description. Logic Function Table PI5A3158B
Low oltage Dual SPDT Analog Switch 2:1 Mux/Demux Bus Switch Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 8Ω at 3.0 Wide Range: 1.65 to 5.5 Rail-to-Rail Signal Range Control
More informationPI3V514. Low On-Resistance, 3.3V High-Bandwidth 5-port, 4:1 Mux/DeMux VideoSwitch. Description. Features. Pin Configuration.
Features Near-Zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (400 MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply 2.5V and 3.3V supply voltage
More informationDescription. Applications
8-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description - - Applications Pin Configuration Block Diagram TSSOP QSOP TQFN Pin Description Pin No Pin Name Description 19
More informationPO3B402A. High Bandwidth Potato Chip OE1 Y1+ Y1- GND SEL3 SEL1 D3- D3+ OE2 Y2+ Y2- Y3+ M3- M3+ OE3 SEL2 OE3 Y3+ Y3- SEL3 OE4 Y4+ Y4- SEL4
FEATURES: Patented technology High signal -3db passing bandwidth at GHz Near-Zero propagation delay CC =.65 to 3.6 Ultra-Low Quiescent Power: 0.µA typical Ideally suited for low power applications Industrial
More informationPI3L V Quad, 2:1 Mux/DeMux Fast Ethernet LAN Switch w/ Single Enable. Description. Features. Applications. Pin Configuration.
Features R ON is 4Ω typical Low crosstalk: 27dB @ 250 MHz Near-Zero propagation delay: 250ps Switching speed: 9ns Channel On capacitance: 9pF (typical) Operating Range: +3.0V to +3.6V >2kV ESD protection
More informationFST Bit Bus Switch
Features 4 Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description December 2012
More informationFST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
More informationPI5A3158B Low Voltage Dual SPDT Analog Switch 2:1 Mux/Demux Bus Switch
2:1 Mux/Demux Bus Switch Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 8Ω at 3.0 Wide Range: 1.65 to 5.5 Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5(Min)
More informationCBT bit 1-of-2 multiplexer/demultiplexer with precharged outputs and Schottky undershoot protection for live insertion
INTEGRATED CIRCUITS 16-bit 1-of-2 multiplexer/demultiplexer with precharged outputs and Schottky undershoot protection for live insertion 2000 Jul 18 FEATURES 5 Ω typical r on Pull-up on B ports Undershoot
More informationPI3USB10LP-A. USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications. Description. Features.
Features USB 2.0 compliant (high speed and full speed) R ON is 5.5Ω typical @ V CC = 3.0V Low bit-to-bit skew Low Crosstalk: 40dB @ 500 Mbps Off Isolation: 35dB @ 500 Mbps Near-Zero propagation delay:
More informationFST Bit Low Power Bus Switch
FST3384 10-Bit Low Power Bus Switch General Description The Fairchild Switch FST3384 provides 10 bits of highspeed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to
More informationPI74LPT V, 16-Bit Buffer/Line Driver. Features. Description. Block Diagram
Features Compatible with LCX and LVT families of products Supports 5V Tolerant Mixed Signal Mode Operation Input can be 3V or 5V Output can be 3V or connected to 5V bus Advanced Low Power CMOS Operation
More informationFST32X Bit Bus Switch
FST32X245 16-Bit Bus Switch General Description The Fairchild Switch FST32X245 provides 16-bits of high speed CMOS TTL-compatible bus switching in a standard flow-through mode. The low On Resistance of
More informationFST Bit Bus Switch
FST3126 4-Bit Bus Switch General Description The Fairchild Switch FST3126 provides four high-speed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to be connected to
More informationFST Bit Bus Switch
24-Bit Bus Switch General Description The Fairchild Switch FST16211 provides 24-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows inputs to be connected to
More informationPI2DBS GHz, Differential Broadband Signal Switch, 2-Differential Channel, 2:1 Mux/DeMux Switch
Features SAS, SATA2, XAUI Switch 2 Differential Channel, 2:1 Mux/DeMux Bandwidth of 2.0 GHz (3dB) Low Bit-to-Bit Skew :
More informationPI5V330A. Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux. Features: Description. Pin Diagram. Block Diagram. Pin Description.
Features: High-performance solution to switch between video sources Wide bandwidth: >360 MHz Low On-Resistance: 3Ω Low crosstalk at 0 MHz: 58dB Ultra-low quiescent power (0.µA typical) Single supply operation:
More informationA product Line of Diodes Incorporated. Description EN S 1 IA 3 IA 2 IA 1 GND. Note: 1. N.C. = No internal connection.
Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Features ÎÎNear-Zero propagation delay ÎÎ5Ω switches connect inputs to outputs ÎÎHigh signal passing bandwidth (-3dB BW is 815MHz)
More informationFST Bit to 32-Bit Multiplexer/Demultiplexer Bus Switch
September 1997 Revised November 2000 FST16233 16-Bit to 32-Bit Multiplexer/Demultiplexer Bus Switch General Description The Fairchild Switch FST16233 is a 16-bit to 32-bit highspeed CMOS TTL-compatible
More informationFST Bit Bus Switch
Features 4Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description March 2008 Fairchild
More informationPI3USB V, USB 2.0 High-Speed Signal Switch w/ Low THD Channels for Audio Signals. Features. Pin Description. Truth Table
w/ Low THD Channels for Audio Signals Features Bandwidth for USB ports > 1.2Gbps Low THD for Audio ports < 0.02% ESD > 2kV HBM Low I CC = 800µA Wide V CC operating range: 2.7V to 4.2V ±10% Packaging: Pb-free
More informationFSTU32160A 16-Bit to 32-Bit Multiplexer/Demultiplexer Bus Switch with 2V Undershoot Protection
June 1999 Revised December 2000 FSTU32160A 16-Bit to 32-Bit Multiplexer/Demultiplexer Bus Switch with 2V Undershoot Protection General Description The Fairchild Switch FSTU32160A is a 16-bit to 32-bit
More informationFST3253 Dual 4:1 Multiplexer/Demultiplexer Bus Switch
Dual 4:1 Multiplexer/Demultiplexer Bus Switch General Description The Fairchild Switch FST3253 is a dual 4:1 high-speed CMOS TTL-compatible multiplexer/demultiplexer bus switch. The low on resistance of
More informationPI6CL V/1.5V, 200MHz, 1:4 Networking Clock Buffer. Features. Description. Pin Description
Features High-speed, low-noise, non-inverting 1:4 buffer Maximum Frequency up to 200 MHz Low output skew < 100ps Low propagation delay < 3.5ns Optimized duty cycle 3.3 tolerent input 1.2 or 1.5 supply
More informationUNISONIC TECHNOLOGIES CO., LTD US5C3257 Preliminary CMOS IC
UNISONIC TECHNOLOGIES CO., LTD US5C3257 Preliminary CMOS IC QUAD 2:1 MUX/DEMUX BUS SWITCH DESCRIPTION The UTC US5C3257 is a QUAD 2:1 multiplexer/demultiplexer with low on-resistance and is pinout and function
More informationFSTD Bit Bus Switch with Level Shifting
FSTD16861 20-Bit Bus Switch with Level Shifting General Description The Fairchild Switch FSTD16861 provides 20-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows
More informationPI5V330S. Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux. Features. Description. Block Diagram. Pin Configuration.
Features High-performance solution to switch between video sources Wide bandwidth: 570 MHz (typical) Low On-Resistance: 5Ω (typical) Low crosstalk at 10 MHz: 80dB Ultra-low quiescent power (0.1µA typical)
More informationCBTS3253 Dual 1-of-4 FET multiplexer/demultiplexer with Schottky diode clamping
INTEGRATED CIRCUITS 2002 Nov 06 Philips Semiconductors FEATURES 5 Ω switch connection between two ports TTL-compatible input levels Schottky diodes on I/O clamp undershoot Minimal propagation delay through
More informationCBTS3306 Dual bus switch with Schottky diode clamping
INTEGRATED CIRCUITS Dual bus switch with Schottky diode clamping 2001 Nov 08 File under Integrated Circuits ICL03 FEATURES 5 Ω switch connection between two ports TTL-compatible input levels Package options
More informationPI3L V, Wide Bandwidth, Quad 2:1 Mux/DeMux LAN Switch
Features Replaces Mechanical Relays High-performance, Low-cost solution for switching between different LAN ignals Ultra-low Quiescent Power (0.1µA typical) Low Crosstalk: 100dB @ 10 MHz Low Insertion
More informationCBTD3257 Quad 1-of-2 multiplexer/demultiplexer with level shifting
INTEGRATED CIRCUITS 2002 Sep 09 FEATURES 5 Ω switch connection between two ports TTL-compatible input levels Designed to be used in level shifting applications Minimal propagation delay through the switch
More informationUNISONIC TECHNOLOGIES CO., LTD
U74CBT3257 4-BIT 1-OF-2 FET MULTIPLEXER/ DEMULTIPLEXER UNISONIC TECHNOLOGIES CO., LTD CMOS IC DESCRIPTION The U74CBT3257 is a 4-bit 1-of-2 high-speed TTL-compatible FET multiplexer/demultiplexer. The low
More informationQS54/74FCT373T, 2373T. High-Speed CMOS Bus Interface 8-Bit Latches MDSL QUALITY SEMICONDUCTOR, INC. 1 DECEMBER 28, 1998
Q QUALITY SEMICONDUCTOR, INC. QS54/74FCT373T, 2373T High-Speed CMOS Bus Interface 8-Bit Latches QS54/74FCT373T QS54/74FCT2373T FEATURES/BENEFITS Pin and function compatible to the 74F373 74FCT373 and 74ABT373
More informationNC7SB3257 TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch
TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch General Description The NC7SB3257 is a high performance, 2:1 NMOS passgate multiplexer/demultiplexer from Fairchild s Ultra High Speed Series of TinyLogic.
More informationUNISONIC TECHNOLOGIES CO., LTD U74CBTLV3125
UNISONIC TECHNOLOGIES CO., LTD U74CBTLV3125 LOW-VOLTAGE QUADRUPLE FET BUS SWITCH DESCRIPTION The U74CBTLV3125 quadruple FET bus switch features independent line switches. Each switch is disabled when the
More informationIn data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below.
Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic
More informationPI3PCIE V, PCI Express Lane, (4-Channel), Differential Mux/Demux with Bypass. Features. Description. Truth Table
3.3V, PCI Express 3.0 2-Lane, (4-Channel), Differential Mux/Demux with Bypass Features ÎÎ8 Differential Channel SPST switch with Mux/DeMux option ÎÎPCIe 3.0 performance ÎÎBi-directional operation ÎÎLow
More informationFSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input
April 2003 Revised July 2004 FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input General Description The FSAT66 is a high speed single pole/single throw normally
More informationNC7SZD384 1-Bit Low Power Bus Switch with Level Shifting
1-Bit Low Power Bus Switch with Level Shifting General Description The NC7SZD384 provides 1-bit of high-speed CMOS TTL-compatible bus switch. The low on resistance of the switch allows inputs to be connected
More informationNC7SZ66 Low Voltage Single SPST Normally Open Bus Switch
September 2013 NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch Features Broad V CC Operating Range: 1.65 V to 5.5 V Rail-to-Rail Signal Handling Power Down High-Impedance Inputs/Outputs 5 Ω Switch
More informationA product Line of Diodes Incorporated. Description. Applications. Truth Table. Note: 1. IEC
2:1 Mux/DeMux Gigabit Ethernet LAN Switch with Power-down Mode Features 1:2 Gigabit LAN Switch Power-down support Low bit-to-bit skew: 200ps Very Low Crosstalk: 75dB @ 250MHz Status Indicator LEDs Switched
More information74ALVC Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs
74ALVC162245 Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs General Description The ALVC162245 contains sixteen non-inverting
More informationIn data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below.
Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic
More informationINTEGRATED CIRCUITS. 74ABT125 Quad buffer (3-State) Product specification Supersedes data of 1996 Mar 05 IC23 Data Handbook.
INTEGRATED CIRCUITS Supersedes data of 1996 Mar 05 IC23 Data Handbook 1998 Jan 16 FEATURES Quad bus interface 3-State buffers Live insertion/extraction permitted Output capability: +64mA/ 32mA Latch-up
More informationUNISONIC TECHNOLOGIES CO., LTD U74HCT245
UNISONIC TECHNOLOGIES CO., LTD U74HCT245 OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS DIP-20 DESCRIPTION The U74HCT245 is designed for the asynchronous communication between data buses. While the direction-control(dir)
More informationINTEGRATED CIRCUITS. CBT3245 Octal bus switch. Product specification Supersedes data of 1998 Dec Jun 19
INTEGRATED CIRCUITS Supersedes data of 1998 Dec 8 2000 Jun 19 FEATURES Standard 245-type pinout 5 Ω switch connection between two ports TTL compatible control input levels Package options include plastic
More informationP54FCT373/74fct373 OCTAL TRANSPARENT LATCH WITH 3-STATE OUTPUTS FEATURES DESCRIPTION. Function, Pinout and Drive Compatible with the FCT and F Logic
P54FCT373/74fct373 OCTAL TRANSPARENT LATCH WITH 3-STATE OUTPUTS FEATURES Function, Pinout and Drive Compatible with the FCT and F Logic FCT-A speed at 5.6ns max (MIL) Output levels compatible with TTL
More informationHigh Speed, 3.3 V/5 V Quad 2:1 Mux/Demux (4-Bit, 1 of 2) Bus Switch ADG3257
High Speed, 3.3 V/5 V Quad 2:1 Mux/Demux (4-Bit, 1 of 2) Bus Switch ADG3257 FEATURES 100 ps propagation delay through the switch 2 Ω switches connect inputs to outputs Data rates up to 933 Mbps Single
More informationQUICKSWITCH PRODUCTS HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH
FEATURES: Enhanced N channel FET with no inherent diode to Vcc 5Ω bidirectional switches connect inputs to outputs Pin compatible with the 74F245, 74FCT245, and 74FCT245T Low power CMOS proprietary technology
More informationDM74LS126A Quad 3-STATE Buffer
DM74LS126A Quad 3-STATE Buffer General Description This device contains four independent gates each of which performs a non-inverting buffer function. The outputs have the 3-STATE feature. When enabled,
More information74LVT245 74LVTH245 Low Voltage Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs
74LVT245 74LVTH245 Low Voltage Octal Bidirectional Transceiver with 3-STATE Inputs/Outputs General Description The LVT245 and LVTH245 contain eight non-inverting bidirectional buffers with 3-STATE outputs
More informationPI2PCIE2422. PCI Express Gen II Compliant, 8-Differential Channel Switch with 8:4 Mux/DeMux Option. Features. Description. Truth Table.
Features 8 Differential Channel SPST switch with Mux/DeMux option PCI Express Gen II performance Low Bit-to-Bit Skew: 10ps (between +/- signals) Low Crosstalk: -15dB @ 3.0 GHz Low Off Isolation: -26db
More information74ABT bit buffer/line driver, non-inverting (3-State)
INTEGRATED CIRCUITS 0-bit buffer/line driver, non-inverting (3-State) Supersedes data of 995 Sep 06 IC23 Data Handbook 998 Jan 6 FEATURES Ideal where high speed, light loading, or increased fan-in are
More informationMM74HC4066 Quad Analog Switch
MM74HC4066 Quad Analog Switch General Description The MM74HC4066 devices are digitally controlled analog switches utilizing advanced silicon-gate CMOS technology. These switches have low ON resistance
More informationPI3HDMI412-B. 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard
Compliant Signal Switch based on TMDS Signaling Standard Features 3.3V 4-Differential Channel 2:1 Mux/DeMux DVI, HDMI, 1.2 +1.2 signal compatible Data Rate: 1.65Gbps Supports both AC coupled and DC coupled
More informationPI3VeDP212 2-lane DisplayPort Switch/Mux for DP Driven Panels with Triple Control Pins
Features 2 Differential Channel, 2:1 mux/demux that will support 2.7Gbps or 1.62Gbps DP signals 1-differential channel is used for AUX signaling Insertion Loss for high speed channels @ 2.7 Gbps: -1.5dB
More information54LVTH Memory FEATURES: DESCRIPTION: 16-Bit Buffers/Drivers with 3-State Outputs. Logic Diagram
16-Bit Buffers/Drivers with 3-State Outputs Logic Diagram FEATURES: RAD-PAK radiation-hardened against natural space radiation Total dose hardness: - > 100 krad (Si), depending upon space mission Output
More information74ABT2244 Octal buffer/line driver with 30Ω series termination resistors (3-State)
INTEGRATED CIRCUITS Supersedes data of 1996 Oct 23 IC23 Data Handbook 1998 Jan 16 FEATURES Octal bus interface 3-State buffers Live insertion/extraction permitted Outputs include series resistance of 30Ω,
More informationPI2PCIE V, PCI Express Gen2 Compliant, 4-Differential Channel, 2:1 Mux/DeMux Switch
Features 4 Differential Channel, 2:1 Mux/DeMux PCI Express, Gen 2 Performance, 5.0Gbps Low Bit-to-Bit Skew, 7ps max (between '+' and '-' bits) Low Crosstalk: -23dB@3 GHz Low Off Isolation: -23dB@3 GHz
More information54BCT244. Octal Buffers/Drivers. Memory DESCRIPTION: FEATURES: Logic Diagram
Logic Diagram FEATURES: 3-state outputs drive bus lines or buffer memory address registers RAD-PAK radiation-hardened against natural space radiation Total dose hardness: - >100 krad (Si), depending upon
More informationPI3PCIE V, PCI Express 3.0, 1-Lane, 2-Channel, 8Gbps, 2:1 Mux/DeMux Switch w/ Single Enable
Features ÎÎ2 Differential Channel, 2:1 Mux/DeMux ÎÎPCI Express 3.0 performance, 8.0Gbps ÎÎBi-directional operation ÎÎ3dB Bandwidth: 8.1GHz ÎÎLow Bit-to-Bit Skew, 10ps max ÎÎLow channel-to-channel skew:
More informationPI3HDMI412FT. 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch with Flow-through Pin Out
Features 4-Differential Channel 2:1 Mux/DeMux DVI, HDMI rev 1.1, and HDMI rev 1.2 signal compatible -3dB BW = 1.5 GHz (3.0Gbps) Crosstalk: -35dB@1.65Gbps Switching speed: 4ns Isolation: -37dB@1.65Gbps
More informationPI5L
Wide Bandwidth Low Voltage LanSwitch Quad 2:1 Mux/Demux Features Replaces mechanical relays High-performance, low-cost solution for switching between different LAN signals Ultra-low quiescent power (0.1
More information54LVTH244A. 3.3V ABT 8-Bit Octal Buffers/Drivers FEATURES: DESCRIPTION: Logic Diagram
54LVTH244A 3.3V ABT 8-Bit Octal Buffers/Drivers FEATURES: Logic Diagram DESCRIPTION: 3.3V ABT octal buffers/drivers with 3-state outputs RAD-PAK radiation-hardened against natural space radiation Package:
More information74ABT245 Octal Bi-Directional Transceiver with 3-STATE Outputs
September 1991 Revised November 1999 74ABT245 Octal Bi-Directional Transceiver with 3-STATE Outputs General Description The ABT245 contains eight non-inverting bidirectional buffers with 3-STATE outputs
More information74LVC16245A/ 74LVCH16245A 16-bit bus transceiver with direction pin; 5V tolerant (3-State)
INTEGRATED CIRCUITS 16-bit bus transceiver with direction pin; 5V tolerant Supersedes data of 1997 Aug 1 IC24 Data Handbook 1997 Sep 25 FEATURES 5 volt tolerant inputs/outputs for interfacing with 5V logic
More information74ABT Bit Transparent D-Type Latch with 3-STATE Outputs
March 1994 Revised November 1999 74ABT16373 16-Bit Traparent D-Type Latch with 3-STATE Outputs General Description The ABT16373 contai sixteen non-inverting latches with 3-STATE outputs and is intended
More informationPI3VDP Lane DisplayPort Rev 1.2 Compliant Switch. Description. Features. Application. Block Diagram
Features ÎÎ2-lane, 1:2 mux/demux that will support RBR, HBR1, or HBR2 ÎÎ1-channel 1:2 mux/demux for DP_HPD signal ÎÎ1-differential channel 1:2 mux/demux for DP_Aux signal with support up to 720Mbps ÎÎInsertion
More information74LVT LVTH16374 Low Voltage 16-Bit D-Type Flip-Flop with 3-STATE Outputs
74LVT16374 74LVTH16374 Low Voltage 16-Bit D-Type Flip-Flop with 3-STATE Outputs General Description The LVT16374 and LVTH16374 contain sixteen non-inverting D-type flip-flops with 3-STATE outputs and is
More informationIn data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below.
Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic
More informationP54FCT240/74fct240 INVERTING OCTAL BUFFER/LINE DRIVER WITH 3-STATE OUTPUTS FEATURES DESCRIPTION
P54FCT240/74fct240 INVERTING OCTAL BUFFER/LINE DRIVER WITH 3-STATE OUTPUTS FEATURES Function, Pinout and Drive Compatible with the FCT and F Logic FCT-A speed at 5.1ns max (MIL) Output levels compatible
More informationCD54/74AC245, CD54/74ACT245
CD54/74AC245, CD54/74ACT245 Data sheet acquired from Harris Semiconductor SCHS245B September 1998 - Revised October 2000 Octal-Bus Transceiver, Three-State, Non-Inverting Features Description [ /Title
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DUAL 4-CHANNEL ANALOG MULTIPLEXER, DEMULTIPLEXER DESCRIPTION The provides common select logic. Each multiplexer has four independent inputs/outputs and a common input/output.
More informationDM74ALS652 Octal 3-STATE Bus Transceiver and Register
DM74LS652 Octal 3-STTE us Transceiver and Register General Description This device incorporates an octal transceiver and an octal D-type register configured to enable transmission of data from bus to bus
More information74VHC VHC VHC Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer
April 1994 Revised April 1999 74VHC4051 74VHC4052 74VHC4053 8-Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer General Description These multiplexers are
More information