KF-510 Series Turbine Flow transducer user's manual

Transcription

1 TM KF-0 Series Turbine Flow transducer NINGBO KIO FLOW INSTRUMENTS CO.,LTD ISO

2 content. Digital paddlewheel meters. Range.External dimension. lectotype.installation requirements.terminal Description.)Terminal Description.)Electric current output.)pulse, frequency output.function of communication 7.Operations.)Panel construction and key definition.)function instructions.) construction.)detail parameter instructions.)detail instructions. Unit of flow. Instantaneous flow Resolution. Unit of total. Cumulative total flow resolution. Damping time(s)..7 Scale flow (m/h).8 Small flow termination%(low %).9 Frequency upper limit Hz.0 Liter/pulse(L/P). Cumulate Clear. Preset total positive P0 P0 P0 P0 P0 P0 P0 P0 P07 P07 P07 P08 P09 P0 P P P P P P P7 P8 P9 P0 P

3 . Digital paddlewheel meters series is as a speed flow metering,used to measure the full closure of pipeline and continuous flow of volume liquid.it is good for low viscosity liquids that can with high accuracy of instant and totalizer flow. Features: High accuracy digital paddlewheel technology Rate and total flow display Easy to operations and read,eight large digital LCD display Install quickly on existing pipe No pressure drop Corrosion resistant PVDF sensor Minimal maintenance required Long-life lithium battery Stopped-flow instructions Diversification installation Totalizer :can be reset and the permanent preservation User set security password Paddlewheel flow sensor Item paddlewheel flow sensor Velocity range 0.~m/s DN0-DN0 (with PVDF triplet) Diameter DN-00(insert type) Wetted material Sensor:PVDF Impeller:PVDF Shaft lever:ceramics Seal ring Viton,EPDM Working temperature PVDF: -0~ +0ºC Working pressure.0mpa, 0.8MPa Technical parameter Item Model Full scale accuracy Repeatability Temperature External dimension Installation method Power supply Output signal Communication Alarm Protection class Consumption Flow Convertor ±%,±.% ±0.% -0~ +ºC 00x00mm Panel mount compact type(dn0~dn0) DCV, battery power supply, AC0V ~0mA, Passive pulse RS8 Upper limit,lower limit,totalizer IP W Http: //

4 TM. Range Technical parameter DN(mm) Range (m³/h) Male 0 0.~.8 G/8 0.~ G/ 0 0.~ G/ 0.~ G 0.~ G½ Press (MPa) temp. (ºC).0 80ºC 0.8 A mm B mm G/8 G/ G½ ~0 G 8 7 A 0 B Insert type technical parameter DN(mm) Range (m/h) Press (MPa) temp. (ºC) Application Water treatment systems 0 ~0 ~0 80 8~ ~00 ~0 0 ~0 Counter-infiltration 00 0~00 Process flow monitor 0 80~800 Ultra-pure water delivery 00 00~000 Http: // Process treatment/ distribution Irrigation system Filtration system ºC Swimming pool and hot spring Groundwater packing Desalination and recycle Process cooling water

5 . External dimension 00mm 8mm 9 x 9mm 00mm. lectotype A: Compact Construction{ B: Remote Sensor Diameter Type of flow transmitter { AT: instantaneous delivery, flow totalizer AF: instantaneous delivery, flow totalizer,-0ma output signal AC: instantaneous delivery, flow totalizer,pulse output signal AD: instantaneous delivery, flow totalizer,rs8 {. L/S. L/min. L/h Flow unit. m³/s. m³/min. m³/h B:Battery power Power supply D: DCV { A B DN:0~0 AT AF AC AD B D 选型示例 - A AF B Http: //

6 . installation requirements Minimum straight pipe length requirements The digital paddlewheel meters accuracy is affected by disturbances such as pumps,elbows,tees,valves,etc.in the flow stream,install the meter in a straight run of pipe as far as possible from any disturbances.the distance required for accuracy will depend on the type of flange reducing 90 elbow xi.d. xi.d. xi.d. xi.d. 0xI.D. xi.d. x90 elbow division plane x90 elbow pump/valve xi.d. xi.d. 0xI.D. xi.d. 0xI.D. xi.d. Mounting location The digital paddlewheel meters is designed to withstand outdoor recommended vertical conditions.a cool,dry location,where the unit can be easilyl serviced is recommended.the meter can be mounted on horizontal or vertical runs of pipe.mounting at the vertical(twelve o clock)position on horizontal pipe is recommended.mounting anywhere around the diameter of vertical pipe is acceptable,however,the pipe must be completely full of water at all times.back pressure is essential on downward flows.see the minimum straight length of pipe requirement chart above.the meter can accurately o acceptable measure flow from either direction. Http: //

7 . Terminal Description back light switch + -0mA KHz - + RS DATA - Vo+ SIN+ SIN- + BAT - + -VDC - OFF AMP ON.)Terminal Description Items Label Function Instructions Remarks -0mA + -0mA - 0~KHz+ 0~KHz- RS8date+ RS8date - 7 Vo+ 8 SIN+ 9 SIN- -0mA Output positive terminal -0mA Output negative terminal Frequency/pulse output positive terminal Frequency/pulse output negative terminal RS8 Communication positiveterminal RS8 Communication negativeterminal Hall parts supply signal + signal -, Load resistance:70q (with link), Hart Communications external VDC power supply Active Output Mode The output amplitude of V load current <=0mA RS8 communication function (n just for transmitter has this function When the signal sensing element is a coil,connect signal + and signal (hop cap connect AMP and ON) when signal sensing element is Hall Parts,hop cap connect AMP and OFF 0 -V + -V - VDC Power, positive terminal VDC Power, negative terminal Power range: VDC -VDC BAT+ BAT- battery supply+ battery supply- When power is battery,we suggest pull out the hop cap of SW for extend battery service life. Http: //

8 .)Electric current output -0mA + -0mA - Receive Instruments The converter current output electrical isolation has been achieved. Output to take an active approach. Current output mode -0mA, 0mA current output value from the corresponding traffic parameter item "scale flow of value" is determined (reference to factory nameplate on the instrument measuring range a value). The maximum current output load resistance of 70Q, the load resistance includes the cables used to connect the resistance. Current output cable is recommended RWPx/0 PVC insulated sheathed cable shield...)pulse, frequency output VDC+(VDC+) KΩ(KΩ) 0~KHz+ 0~KHz- + - Counter VDC-(VDC-) The Transmitter frequency, pulse output has been achieved electrical isolation, the output for the active mode (see above chart). Transmitter frequency, pulse output with transistor output mode. Maximum pulse output frequency KHZ, the output pulse amplitude of V. Active mode the maximum load current 0mA, passive mode the maximum load current 0.A. As the frequency and pulse output terminals are shared, it is not to choice two output modes. Users can set the parameter "frequency output" to select the work. Frequency output upper limit corresponding to the measured flow value by the parameter item "scale flow value" decision (reference instruments to measure the scope of a factory nameplate values). Pulse output equivalent by the parameter 'pulse equivalent L / P "decision. Http: //

9 .) Function of communication Transmitter communication with RS8, MODBUSASC, MODBUSRTU communications capabilities (requires a user specified when ordering). Available through the "8 output communication protocol" parameter is set to specify. Instrument Communication Interface specific technical note on "protocol." 7.Operations.) Panel construction and key definition m /h % m.) Function instructions set parameters confirmation and set key of exit sub- ( key) enter sub- and cancel set key( key) set item DOWN and data variables degression key( set item MOVE and data variables increase key ( key) key) Instructions: Instrument Display Interface. The first line shows an instantaneous flow rate, flow rate display units can be in the 'flow unit' function key to choose;. The second line shows the cumulative total amount and cumulative units;. The third line shows the percentage of traffic 7 Http: //

10 .) construction Mode of Measuree press Configuration Menu press Parameter item Press Secondary Parameter item. PV Units.. BASIC... Damping(s) 0.~ Language... Qmax(m/h).. Low Cutoff%.. Freq Direct.. Freq Max(Hz)... Liter/Pulse. SYSTEM.. Pulse Width(ms).. Pulse Level.. RS8 Ptotocol.. Baudrate. RS8 Output.. Data Bit.. Parity.. Stop Bit.. Dev Address. Total Set. Load Settings.. Clear Total.. FWD preset(m). CALIBRATION. ma Trim. 0mA Trim. TEST. Loop Test. Pulse Test Mode of Measuree Press Configuration Menu press Parameter item Press Secondary Parameter item Press 8 Http: //

11 .) detail parameter instructions parameter item parameter setting range instructions flow unit totalizer unit flow display resolution totalizer display resolution language L/S L/m L/h m/s m/m m/h G/S G/m G/h L m,g chinese english S=second,M=minute, H=hour,L=liter, M=cubic meter,g=gallon set the instantaneous flow of decimal places displayed set the totalizer flow of decimal places displayed scale flow termination of small flow unit m/h this parameter can move small flow display,the percentage for the full range upper frequency limit pulse equivalent pulse width pulse level clear accumulation preset positive accumulation ma calibration 0mA calibration Hz larger than system s minimum is ok ms low effective,high effective No Yes maximum frequency output,it s effectual when pulse equivalent is ZERO one pulse on behalf of how many liters do not need under normal condition clear total accumulation If replace instrument,can input previous totalizer flow,continue to accumulation calibrate output signal without flow. calibrate output signal of full range 9 Http: //

12 ). detail instructions.) Unit of flow Adjust instant flow s unit, the setting rang L/S L/min L/h m/s m/min m/h G/S G/min G/h Steps Operation instructions Interface show In the measurement mode, press into configuration Basic System Calibration Test into Basic PV Units into PV Units PV Units L/h L/h Prees or set the Unit of flow PV Units L/h m /h Current value Modify value Press quit setup,lcd show confirm PV Units ENT ESC L/h m/h to confirm the change to give up modify PV Units 7 two times back to mesurement also you can continue other operation 0 Http: //

13 . )Instantaneous flow Resolution Adjust the instantaneous flow of small points indicate the medium, set the range of - Steps Operation instructions Interface show In the measurement mode, press into configuration Basic System Calibration Test Click into Basic to choice PV decimal PV Units Click into PV decimal Prees or set the nstantaneous flow Resolution Current value Modify value Press quit setup,lcd show confirm ENT ESC to confirm the change to give up modify PV Units 7 two times back to mesurement also you can continue other operation Http: //

14 .) Unit of total Adjust Total unit, setting range L,m,gal Steps Operation instructions Interface show In the measurement mode, press into configuration Basic System Calibration Test Click into Basic to choice l PV Units Click into L m Prees or set the Unit of total L m Current value Modify value Press quit setup,lcd show confirm ENT ESC L m to confirm the change to give up modify PV Units 7 two times back to mesurement also you can continue other operation Http: //

15 . )Cumulative total flow resolution Adjusted cumulative flow dots show the median, set the range of - decimal places Steps Operation instructions Interface show In the measurement mode, press into configuration Basic System Calibration Test Click into Basic to choice PV Units Click into Prees or set the Cumulative total flow resolution current value Modify value Press quit setup, LCD show confirm ENT ESC to confirm the change to give up modify PV Units 7 two times back to mesurement also you can continue other operation Http: //

16 .) Damping time S Damping time on the meter display and output. Set range o -99 9S (unit is "seconds"). Set as follows: Steps Operation instructions Interface show In the measurement mode, press into configuration Basic System Calibration Test Click into Basic to choice Damping(S) Damping(S) Click into Damping(S) Damping(S) Max: 99.9 Min: Prees or and set the Damping time Damping(S) Max: 99.9 Min: current value Modify value Press quit setup, LCD show confirm Damping(S) ENT ESC to confirm the change to give up modify Damping(S) 7 two times back to mesurement also you can continue other operation Http: //

17 . ) system constituent s initial password:000 Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item press the key of,show password interface,enter password,press the key of enter into system constituent Click into Basic System Calibration Test Language Prees or and set the current value Modify value Press quit setup, LCD show confirm ENT ESC to confirm the change to give up modify Language 7 two times back to mesurement also you can continue other operation Http: //

18 7. )Scale flow (m/h) Meter-scale flow (QMAX) range depending on the caliber meter. Scale flow units: m/h. Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item press the key of,show password interface,enter password,press the key of enter into system constituent Press item to choice Basic System Calibration Test Language Language into Qmax(m/h) Low Cutoff% Press into Qmax(m/h),Prees or and set the Scale flow Qmax(m/h) current value 00.0 Max: Min: Modify value 0.0 Press quit setup, LCD show confirm Qmax(m/h) ENT ESC to confirm the change to give up modify Qmax(m/h Low Cutoff% 8 three times back to mesurement also you can continue other operation Http: //

19 8.) Small flow termination%(low %) The parameters on the display and output are valid. When the traffic signal to terminate below the low flow rate (unit%) of the settings to set the value of the The signal will be removed, display and output to zero. The termination of the small percentage is relative to the scale in terms of flow rate settings. Set As follows Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item press the key of,show password interface,enter password,press the key of enter into system constituent Basic System Calibration Test Language Press item to choice Language Press into Press to choice Low Cutoff item Qmax(m/h) Low Cutoff% Press into Low Cutoff%,Prees or and set the Small flow Low Cutoff% Max: 9.9 Min: current value Modify value Press quit setup, LCD show confirm Low Cutoff% ENT ESC to confirm the change to give up modify Qmax(m/h Low Cutoff% 8 three times back to mesurement also you can continue other operation 7 Http: //

20 9.) Frequency upper limit Hz (output frequency range of the instrument Hz) When the Liter/ pulse = 0.0, the case "frequency cap Hz" setting determines the frequency of the output When the Liter/pulse >0.0, the setting of L/P determines the frequency output Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item Basic System Calibration Test press the key of,show password interface,enter password,press the key of enter into system constituent Language Press to choice item Language Press into,press to choice Freq Max(Hz) item Freq Direct Freq Max(Hz) Liter/Pulse PulseWidth(ms Press into Freq Max(Hz),Prees or and set the Frequency upper limit Freq Max(Hz) Max: Min: current value Modify value Press quit setup, LCD show confirm Freq Max(Hz) ENT ESC to confirm the change to give up modify Freq Direct Freq Max(Hz) Liter/Pulse PulseWidth(ms 8 three times back to mesurement also you can continue other operation 8 Http: //

21 0.) Liter/pulse(L/P) Scale corresponding to the current flow of output frequency Current Flow(m/h) /. Current Flow(L/s) Output Frq(Hz) = Liter/pulse(L/P) Liter/pulse(L/P) Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item Basic System Calibration Test press the key of,show password interface,enter password,press the key of enter into system constituent Language Press to choice item Language Press into,press to choice Liter/Pulse item Freq Direct Freq Max(Hz) Liter/Pulse PulseWidth(ms Press into Liter/Pulse,Prees or and set the Liter/Pulse Liter/Pulse Max: Min: current value Modify value Press quit setup, LCD show confirm Liter/Pulse ENT ESC to confirm the change to give up modify Freq Direct Freq Max(Hz) Liter/Pulse PulseWidth(ms 8 three times back to mesurement also you can continue other operation 9 Http: //

22 . ) Cumulate Clear Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item press the key of,show password interface,enter password,press the key of enter into system constituent Press to choice Total Set item Basic System Calibration Test Language RS8 Output Total Set Press into Clear Total Clear Total FWD Preset(m) Press into Clear Total,Prees or set the YES or NO Clear Total NO Yes current value Modify value Press quit setup, LCD show confirm Clear Total ENT ESC NO Yes 7 two times to Clear Total to give up modify Clear Total FWD Preset(m) 8 three times back to mesurement also you can continue other operation 0 Http: //

23 . )Preset total positive Steps Operation instructions Interface show In the measurement mode, press into configuration,click to choice System item press the key of,show password interface,enter password,press the key of enter into system constituent Press to choice Total Set item Basic System Calibration Test Language RS8 Output Total Set Press into Clear Total FWD Preset(m) Press to choice FWD Preset(m) item Clear Total FWD Preset(m) Press into Clear Total,Prees or set the YES or NO FWD Preset(m) Max: Min: Press quit setup Clear Total FWD Preset(m) 7 three times back to mesurement also you can continue other operation Http: //

24 NINGBO KIO FLOW INSTRUMENTS CO.,LTD Add:No.0 Xingye Road Yangming Sci.& Tech.Park,P.R.China Tel: Fax: Post Code:00 Http: //