TRIMLIGHT SELECT WIRING INSTRUCTION MANUAL
|
|
- Morgan Bryant
- 5 years ago
- Views:
Transcription
1 TRIMLIGHT SELECT WIRING INSTRUCTION MANUAL
2 Single Strand System (Entire system will be 1 color at a time)
3 Double Strand System (Entire system will can have 2 colors at a time)
4 When placing diode wires, ensure that the male plug side of the diode strings are always facing towards the controller. Towards the RGB controller Female Connector Male Connector
5 Input Output Single Strand System Wiring at an AMPLIFIER (Every 40 diodes) RGB Wire from Controller RGB Wire away from Controller Amplifier Towards the controller Away from the controller Power from Power Supply Power from Power Supply Continue amp wire to next amplifier location Maximum 4 amplifiers per 16/2 Wire (Maximum 200 length of light strings)
6 Input Output Single Strand System Wiring at an AMPLIFIER (Every 40 diodes) For last set of amplifiers on a line RGB Wire from Controller RGB Wire away from Controller Amplifier Towards the controller Away from the controller Power from Power Supply Power from Power Supply Maximum 4 amplifiers per 16/2 Wire (Maximum 200 length of light strings)
7 Input Input Output Output Double Strand System Wiring at an AMPLIFIER (Every 40 s) RGB Wire from Controller RGB Wire away from Controller Amplifier Towards the controller Away from the controller Power from Power Source Continue amp wire to next amplifier location Power from Power Source RGB Wire from Controller RGB Wire away from Controller Amplifier Towards the controller Maximum 4 amplifiers per 16/2 Wire (Maximum 120 length on 1 single 16/2 wire) Away from the controller
8 Input Input Output Output Double Strand System Wiring at an AMPLIFIER (Every 40 s) For last set of amplifiers on a line RGB Wire from Controller RGB Wire away from Amplifier Towards the controller Away from the controller Power from Power Source Power from Power Source RGB Wire from Controller RGB Wire away from Controller Amplifier Towards the controller Maximum 4 amplifiers per 16/2 Wire (Maximum 120 length on 1 single 16/2 wire) Away from the controller
9 Centrally Located Control Box Layout Jump with 18/4 Solid Copper Wire Power Connection and Controllers Amplifier Locations (Approximately 40 from power source or previous amplifier) Trimlight with s Amplifier 16/2 Wire
10 One Sided Location Control Box Layout Jump with 18/4 Solid Copper Wire Power Connection and Controllers Amplifier Locations (Approximately 40 from power source or previous amplifier) Trimlight with s Amplifier 16/2 Wire LIMITATION: On a 2 strand system, with 2 amplifiers at each location with a maximum of 4 on a single 16/2 Amplifier wire. Do not exceed past 4 amplifiers on a single run of 16/2 power wire.
11 Multiple Power Location Control Box Layout Jump with 18/4 Solid Copper Wire Power Connection and Controllers Amplifier Locations (Approximately 40 from power source) Trimlight with s Amplifier 16/2 Wire Secondary Power Supply LIMITATION: On a 2 strand system, with 2 amplifiers at each location with a maximum of 4 on a single 16/2 Amplifier wire. Do not exceed past 4 amplifiers on a single run of 16/2 power wire.
12 Ensuring Proper Voltage to the Power Supply 100 Watt Power Supply On a 100 Watt power supply the voltage switch is internal and difficult to see or access. Using a small screwdriver or tool. Gently insert through the perforated holes to switch the controller to the correct power being supplied. 200 Watt Power Supply On a 200 Watt power supply the voltage switch is external and easy to see and access. Gently switch the controller to the correct power being supplied. The 300 Watt power supply includes this same feature.
13 AMPLIFIER WIRE JUMPER WIRE TO TRIMLIGHT CHANNEL JUMPER WIRE TO TRIMLIGHT CHANNEL Control Box Layout Double Strand Strings Strings RGB Controller RGB Controller R G B R G B 120 Volt Plug L N 5 Volt Power Supply
14 AMPLIFIER WIRE JUMPER WIRE TO TRIMLIGHT CHANNEL Control Box Layout Single Strand Strings RGB Controller R G B 120 Volt Plug L N 5 Volt Power Supply
15 Jumper Wire Example on a single strand system v
16 Jumper Wire Example on a DOUBLE strand system v
17 AMPLIFIER WIRE JUMPER WIRE TO TRIMLIGHT CHANNEL JUMPER WIRE TO TRIMLIGHT CHANNEL Control Box Layout For WiFi Systems Strings Strings WiFi-104-SSID W B G R Volt Plug with Transformer RGB Controller W B G R RGB Controller W B G R 120 Volt Plug L N 5 Volt Power Supply
TRIMLIGHT SELF-INSTALL TRAINING MANUAL
1 TRIMLIGHT SELF-INSTALL TRAINING MANUAL 2 Double Strand System (Entire system will can have 2 colors at a time) 3 One Sided Location Control Box Layout TO NOTE: Control Boxes mounted far from the living
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationAlternating Current Power
Chapter 4 Alternating Current Power MElec-Ch4-1 Overview What is Alternating Current AC Hazards AC Power Requirements Shoreside Utility System On-Board Generators MElec-Ch4-2 What is Alternating Current
More informationBoard Of Education, Revision C (28150)
599 Menlo Drive, Suite 00 Rocklin, California 95765, USA Office: (96) 624-8333 Fax: (96) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Board Of Education,
More informationProduct overview. Features. Product specifications. Order codes. 1kΩ Resistance Output Module
Product overview The AX-ROM135 and the AX-ROM1000 Modules enable an Analogue, Pulse or Floating point signal and convert to either a 0-135Ω or a 1KΩ Proportional Resistive output signal. The output resistance
More informationFlagShip. Installation Guide / User Manual Effective: January 1 st, Table of contents. 1. FlagShip Preconfiguration
FlagShip Installation Guide / User Manual Effective: January 1 st, 2016 Please go to our website for the most current version of the FlagShip Installation and Instruction Manual at www.schaller-electronic.com,
More informationHow To Install Weather Pack Bulkhead Wire Connectors
How To Install Weather Pack Bulkhead Wire Connectors Weather Pack wire connectors are the premium line of environmentally sealed connectors from Delphi/Packard. The bulkhead series creates a secure and
More informationScaleRCHelis.com V Light Controller Kit
Thank you for purchasing the ScaleRCHelis.com V1.1 450 Light Controller Kit. This is something you can build in under a hour with some simple soldering equipment. Your kit will include all the parts necessary
More informationTOA PROFESSIONAL POWER AMP
Operating Instruction Manual TOA PROFESSIONAL POWER AMP Model P-150M, P-300M TOA ELECTRIC CO, LTD. KOBE, JAPAN Contents Precautions... 2 General Description... 2 Features... 3 Specifications... 4~5 Performance
More informationS&T GeoTronics LLC Open DSKY with AGC Assembly Instructions
S&T GeoTronics LLC Open DSKY with AGC Assembly Instructions First, make sure you have all the required components: HARDWARE Qty Item 1 DSKY PCB v1.0d 1 Arduino Nano 1 VA RTC 1 IMU 1 Buck StepDown 1 SKM53
More informationLITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
More informationTerminal Replacement Procedures
HOW TO REPLACE CONNECTOR TERMINALS The terminal repair kits provide necessary tools and materials (terminals, wire seals, and splice connectors) to repair many damaged or faulty connector terminals. However,
More informationLC31L-BAT Link Coupler
Instruction Manual For the LC31L-BAT Link Coupler 09 March 2018 2012-2018 by Ralph Hartwell Spectrotek Services All rights reserved 2 RADIO FREQUENCY WARNING NOTICE If the LC31L-BAT is installed incorrectly
More informationLED Infinity Mirror Controller, 32 LEDs, Multiple Patterns.
http://wwwinstructablescom/id/led-infinity-mirror-controller-32-leds-multiple-/ Food Living Outside Play Technology Workshop LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns by ChromationSystems
More informationBEGINNER'S GUIDE TO AUDIO CONNECTIONS Copyright 2011 by Bruce Bartlett
BEGINNER'S GUIDE TO AUDIO CONNECTIONS Copyright 2011 by Bruce Bartlett An audio system has so many cables and connectors, it's easy to become confused. What plugs into what? This article will help you
More informationPatton Robotics, LLC.
Patton Robotics LLC Patton Robotics T3 Motherboard Assembly Instructions Version 1.1 Patton Robotics, LLC. 61 Hagan Drive New Hope, PA 18938 Phone: 609-977-5525 Email: pattonrobotics@gmail.com Copyright
More informationWhat you should have. 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring. 3. Numbered bars or spokes(8) 4. Center plate (1)
20 ft RGB Pole Tree What you should have 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring 3. Numbered bars or spokes(8) 4. Center plate (1) 5. Top Ring (1) 6. Hardware and wrenchs a. Hardware i.
More informationDual Band Filter Assembly Manual
Dual Band Filter Assembly Manual 12 January 2018 Rev D Version Theory of Operation: The purpose of a Bandpass Filter is to filter out or reject all unwanted signals. The original KN-Q7A Receive Filter
More informationTOA 900 SERIES POWER AMPLIFIER P-924A
Operation Instruction Manual TOA 900 SERIES POWER AMPLIFIER P-924A Features General Descriptions 1 Wide frequency response; 20 20,000 Hz, ±1dB 2 Low distortion and noise level 3 Excellent output regulation
More informationPoke-Home: Horizontal AWG: WTB INTER CONNECT APPLICATIONS FEATURES AND BENEFITS ELECTRICAL MECHANICAL ENVIRONMENTAL HOW TO ORDER 00X
The new 9276 series connector provides a quick and reliable wire-toboard termination in a sleek 2.5mm pitch SMT package for a broad range of industrial and commercial markets. With almost every product
More informationTechnical Service Bulletin DCX AGC Setup Procedure for ADAPT IV Exciters
Technical Service Bulletin 110427 DCX AGC Setup Procedure for ADAPT IV Exciters This service bulletin provides the procedure to properly install and align the total system automatic gain control (AGC)
More informationLabs. Introduction. Specialty Family
INC. Labs Introduction Specialty Family Features K-Jumper: Affordable, High Performance Interconnect up to 35 GHz Sta-Put: Zero Loading Test Cable Space-Flex : Semi-Rigid and Flexible Cable Assemblies
More informationTYPICAL FLEX TAPE ASSEMBLY
TYPICAL FLEX TAPE ASSEMBLY Basic Specifications to Install Tresco Lights Basic Specifications to Install Tresco Lights With With a PLug-In a PLUG-IN To control each light individually, use Option 1. To
More informationQUICKSILVER MX-190 OPERATING INSTRUCTIONS ,,-
QUICKSILVER MX-190 OPERATING INSTRUCTIONS -------..,,- INPUT CONNECTIONS To maintain a short and concise signal path, the input connectors are mounted directly on the plug-in front-end circuit boards.
More informationLabs. Introduction. Specialty Family
INC. Labs Introduction Specialty Family Features K-Jumper: Affordable, High Performance Interconnect up to 35 GHz Space-Flex : Semi-Rigid and Flexible Cable Assemblies for S-Level Space T-Flex : Flexible
More informationContents. Warranty and Disclaimer 2
Contents Warranty and Disclaimer 2 Physical Dimensions Board Layout 3 Usage Using the PWM board 4 Setting the start address 4 Dimming LED s 5,6 Typical hookup 7 Terminator 8 Troubleshooting Ground, termination,
More informationLab #1: Electrical Measurements I Resistance
Lab #: Electrical Measurements I esistance Goal: Learn to measure basic electrical quantities; study the effect of measurement apparatus on the quantities being measured by investigating the internal resistances
More informationThe Instructions should be read, prior to commencing the installation, failure to follow these instructions will void your warranty.
Low Voltage System The Platinum Low Voltage lighting system can power up to 120 candle pods depending on the length of cables used during the installation this can reduce the number of pods to 24 per outlet
More informationR12V 12-VOLT STANDARD OUTPUT 12V INDOOR STANDARD OUTPUT LED RIBBON 12V WET LOCATION STANDARD OUTPUT LED RIBBON WESTGATE MFG
RIBBO LIGHTIG I 12V RIBBO R12V 12-VOLT STADARD OUTPUT R12V-5M-D3-CW TECHICAL SPECIFICATIOS: :: : chip spaced 5/8 on center, per foot,.08 watts each chip :: Dimmable using a magnetic driver :: Cutting increment:
More informationTechnical Service Bulletin DCX AGC Setup Procedure for MODAP Exciters
Technical Service Bulletin 030624 DCX AGC Setup Procedure for MODAP Exciters This service bulletin provides the procedure to properly install and align the total system automatic gain control (AGC) upgrade
More informationPi-Cars Factory Tool Kit
Pi-Cars Factory Tool Kit Posted on January 24, 2013 Welcome to the factory: Welcome to where you will learn how to build a Pi-Car, we call it the Pi-Cars Factory. We hope that this page contains all you
More informationSpecimen Products Single Ended Stereo Amp Instruction Book
Specimen Products Single Ended Stereo Amp Instruction Book Specimen tube amplifier designs are informed by decades of servicing and building musical instrument amps. As a result of being subjected to the
More informationUser Manual for Polybass-R
User Manual for Polybass-R (RMC/Godin Multiac version) V6 17.2.2018 about this manual the Polybass board serves for any guitar if there is a polyphonic (hexaphonic) pickup and enough space for the board
More informationPacific Antenna Simple Keyer Kit
Pacific Antenna Simple Keyer Kit Specifications and Features: Speed range of 5 to 30 wpm Operates in either iambic A or B mode, with B being the default 2 message memories Tune and Beacon modes Built on
More informationD.I.Y L.E.D CUBE 4X4X4. Level: Intermediate
EN D.I.Y L.E.D CUBE 4X4X4 Level: Intermediate AK-125 TABLE OF CONTENTS Parts List... 2 Soldering Guide (Part A)... 3 Soldering Guide (Part B)... 5 Soldering Guide Without Recommend Products... 8 Appendix...
More informationLESLIE CONSOLE CONNECTOR KIT 7043 INSTALLATION INSTRUCTIONS
LESLIE CONSOLE CONNECTOR KIT 7043 INSTALLATION INSTRUCTIONS FOR USE WITH: LESLIE Speaker Models: 125, 225, 145, 147, 147RV, 247, 247RV WURLITZER Organ Models: 4300, 4500, 4520 MULTIPLE SPEAKER INSTALLATION:
More informationREAD THIS BEFORE ATTEMPTING TO COMBINE
HANDBOOK FM SERIES 2000W POWER COMBINER READ THIS BEFORE ATTEMPTING TO COMBINE 4 s PTEK Contents Theory of operation...2 Specifications...3 Safety Notice...4 Rear Panel Layout...5 Installation...8 Schematic
More informationBrewsBySmith.com STC DIY Kit
BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)
More informationPLEASE READ THIS MANUAL BEFORE ATTEMPTING TO OPERATE EQUIPMENT!!
PLEASE READ THIS MANUAL BEFORE ATTEMPTING TO OPERATE EQUIPMENT!! UNPACKING INSTRUCTIONS 1. Carefully lift the amplifier by the bottom cabinet edge out of the shipping carton. Place the amplifier on a firm,
More informationLED Modifications. Below are directions on how I modify LED strings for repairs, upgrade to full wave rectification, or custom lengths/number of LEDs.
LED Modifications Below are directions on how I modify LED strings for repairs, upgrade to full wave rectification, or custom lengths/number of LEDs. Caution! Working with electricity and modifying electrical
More informationBrief User Guide. Ghent s Amplifiers. Written by: Ghent Xu Verified by: Walton Huang Circulation: Ghent Xu Version: 1.
Page 1 of 11 Ghent DIY-Kits & Amplifier windowsxp@vip.163.com Ghent s Amplifiers Brief User Guide Written by: Ghent Xu Verified by: Walton Huang Circulation: Ghent Xu Version: 1.1 Date: 2012/3/5 Page 2
More informationBlue Point Engineering
DMX Data Analyzer Board nstruction Overview DMX Analyzer - Tester PC Board Design your own enclosure with an analyzer / tester display or add to your existing equipment or system. The DMX Analyzer is a
More informationQ107/Q107A State Variable Filter
Apr 28, 2017 The Q107 is dual-wide, full-featured State Variable filter. The Q107A is a single-wide version without the Notch output and input mixer attenuator. These two models share the same circuit
More informationWritten By: Chad Facciolo
HTC One Mini 2 Charging Port Replacement These instructions will show you how to replace your charging port. Written By: Chad Facciolo ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION The charging
More informationIRAC1150-D2 Control Board User s Guide
Computing & Communications SBU - AC-DC Applications Group 222 Kansas Street, El Segundo CA90245, California, USA IRAC1150-D2 Control Board User s Guide Rev. 2.0 7/6/2005 Rev. 2.0 7/6/2005 International
More informationTHE TOOLS RECOMMENDED Phillips Screwdriver Stripper/Crimper Electrician Pliers ½ open end wrench or ratchet wrench with ½ deep socket Utility knife
16 X 20 HEATER ELEMENT WIRE CONNECTION REPAIR DK20/A/S/SP The following instructions are on the repair of a potentially faulty wire connection in your 16 x 20 heat platen. It is recommended that only those
More informationTVC-1 TABLETOP STEREO VOLUME CONTROL
INSTALLATION & OPERATION GUIDE Niles Audio Corporation www.nilesaudio.com 12331 S.W. 130 Street Miami, Florida 33186 Tel: (305) 238-4373 Fax: (305) 238-0185 2004 Niles Audio Corporation. All rights reserved.
More informationPower Distribution Units
Power Distribution Units How to get the power around the Rack Made Simple 2005 IBM Corporation delivers resilient power quality solutions that minimize interruptions to business operation and helps improve
More informationELECTRONIC DESIGN & ENGINEERING. ICP_FM3 Versatile DC AC IEPE Signal Conditioning. 1 ICP_FM3 Introduction
1 ICP_FM3 Introduction ICP_FM3 is a versatile signal conditioning module for DC / AC or IEPE (ICP TM ) applications. The amplifying circuit is additionally equipped with a switchable constant current source,
More informationLoad Bank Design. Joshua Bardwell
Load Bank Design Joshua Bardwell http://www.fpvknowitall.com Finding the right parts is hard. I ve found the stuff that works. Here's a list of gear that you can trust is worth the price, whether your
More informationAssembly Instructions for the FRB FET FM 70 Watt Amp
Assembly Instructions for the FRB FET FM 70 Watt Amp 1.) Orient the circuit board with the diagram 2.) Use a narrow chisel tip 25-30 watt soldering iron for assembly 3.) All the small parts are taped onto
More informationHow to Wire an Inverting Amplifier Circuit
How to Wire an Inverting Amplifier Circuit Figure 1: Inverting Amplifier Schematic Introduction The purpose of this instruction set is to provide you with the ability to wire a simple inverting amplifier
More informationDigital Lighting Systems, Inc.
PD408-AN0-277 ANALOG 0-0 V 0-0V analog control 4 Channel x 2250 W Dimmer & Switch Packs 220/240/277 Volts operation PD408-AN0-277 4 circuit Analog -0V 4 x 8 A. Dimmer pack Serial Number Digital Lighting
More informationThe Art of Electrical Measurements
The Art of Electrical Measurements Purpose: Introduce fundamental electrical test and measurement tools and the art of making electrical measurements. Equipment Required Prelab 1 Digital Multimeter 1 -
More informationOpen DeviceNet Vendor Association, Inc. (ODVA) PMB State Road 7 #F6 Boca Raton, FL Phone: (1) Fax: (1)
Open DeviceNet Vendor Association, Inc. (ODVA) PMB 499 20423 State Road 7 #F6 Boca Raton, FL 33428-6797 Phone: (1) 954 340-5412 Fax: (1) 561 340-5413 e-mail: odva@powerinternet.com Web: www.odva.org 1
More informationENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC. Wire Gauge Size. Code Accepted Max Wire Gauge Insulation AWG Solid or Stranded
AVX continues to develop innovative connectors for the industrial electronics market that provide significant benefits over existing, outdated connector solutions. Listening to the design engineering community,
More informationC22 Vacuum Tube Preamplifier Complete User Manual Analog Metric
C22 Vacuum Tube Preamplifier Complete User Manual Analog Metric sales@analogmetric.com Copyright 2009 All Rights Reserved [C22 VACUUM TUBE PREAMPLIFIER COMPLETE USER Page 2 INTRODUCTION The circuit design
More informationEXAMPLE. Use this jack for the red test lead when measuring. current from 0 to 200mA. Figure P-1
Digital Multimeters ON / OFF power switch Continuity / Diode Test Function Resistance Function Ranges from 200Ω to 200MΩ Transistor Test Function DC Current Function Ranges from 2mA to 20A. AC Current
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationAntenna Disconnect THE INEXPENSIVE WAY TO PROTECT YOUR VALUABLE RADIO FROM LIGHTNING SURGES
Antenna Disconnect THE INEXPENSIVE WAY TO PROTECT YOUR VALUABLE RADIO FROM LIGHTNING SURGES -------------------------------------------------------------------------------------- Operating Manual May 2017
More informationunit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS
Electrical/Electronic Systems unit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS lesson 4: wire and connector repairs I. Connector repairs A. Connector repairs involve fixing damaged wires. Wires are marred due
More informationBeta-test ED1 PCB installed in I0CG s K1
K1 SSB Modification (Ed.2) This description provides the receiver (RX) modifications, assembly, alignment and operation as a first step. In a second step you can add the remaining transmitter (TX) modifications,
More informationQuantum LX Motor Current Testing
The Quantum LX control panel is capable of reading external analog devices, such as Current transformers (CT) or other external devices, such as a VFD. It uses these input signals for the purpose of monitoring
More informationExperiment #3: Micro-controlled Movement
Experiment #3: Micro-controlled Movement So we re already on Experiment #3 and all we ve done is blinked a few LED s on and off. Hang in there, something is about to move! As you know, an LED is an output
More informationInstruction Manual. SSQ-2F Controller Board. For the. v1.41 For Rife Plasma Tube Systems. Manual v by Ralph Hartwell Spectrotek Services
Instruction Manual For the SSQ-2F Controller Board v1.41 For Rife Plasma Tube Systems Manual v1.00 2012 by Ralph Hartwell Spectrotek Services This page intentionally blank. 2 Index and Table of Contents
More informationdiode led DAZZLE ACCENT LIGHTING SYSTEM POWERED BY INCEPTION LIGHTING TECHNOLOGY IP65 24VDC SPECIFICATIONS CHANNEL COVER AVAILABLE IN:
DAZZLE ACCENT LIGHTING SYSTEM SPECIFICATION SHEET ITEM # 24VDC RGB CHANNEL COVER AVAILABLE IN: STRIP COLOR LENGTH LUMENS¹ DI-IL-TAPE-BLK-0.5 Black 20 inches 84 DI-IL-TAPE-BLK-1.5 Black 59 inches 252 DI-IL-TAPE-BLK-5.0
More informationPRODUCT DATA SHEET. ColorBright Color Changing. RGB 300 Series. Year Warranty.
PRODUCT DATA SHEET ColorBright Color Changing RGB 300 Series 5 Year Warranty www.flexfireleds.com Description The ColorBright Color Changing 300 LED strip light has double the amount of bright LEDs than
More informationHE Insert Series. Application Specification Apr 26 th, 2016 Rev. A. Table of contents
HE Insert Series Table of contents 1. INTRODUCTION... 2 2. SUPPORTING DOCUMENTS... 2 2.1. Customer drawings... 2 2.2. Product specification... 2 2.3. Application Specification... 2 2.4. Standards... 2
More informationTimes Microwave Systems Hermetically Sealed Assemblies
SCOPE This Specification details the Electrical, Mechanical and Environmental Characteristics of Times Microwave Systems MILTECH 480.48 Diameter Hermetically Sealed Coaxial Transmission Lines. This product
More informationR12V 12-VOLT STANDARD OUTPUT 12V INDOOR STANDARD OUTPUT LED RIBBON 12V WET LOCATION STANDARD OUTPUT LED RIBBON WESTGATE MFG
RIBBO LIGHTIG I 12V RIBBO R12V 12-VOLT STADARD OUTPUT R12V-5M-D3-CW TECHICAL SPECIFICATIOS: :: : chip spaced 5/8 on center, per foot,.08 watts each chip :: Dimmable using a magnetic driver :: Cutting increment:
More information12VDC SMD5050 RGBW 4in1 LED flexible strip, 300LED per 5meter per roll
Item Code LED Type LED QTY. Cuttable Input Voltage Wattage(max) 12VDC SMD5050 RGBW 4in1 LED flexible strip, 300LED per 5meter per roll HK-F5050RGBW4in1X30-X RGBW Color SMD5050 60LED/Meter, 300pcs 4in1
More informationWith Audible Detect Signal
T-100 SERIES SINGLE CHANNEL SHELF MOUNT DETECTOR Meets and exceeds NEMA TS 1 specification. Six front panel DIP switches provide: Seven levels of sensitivity plus off. Presence or Pulse mode. Four loop
More informationT-TRAK PowerPole Bus Wires
Glenn McLain & Steve Jackson, NVNTRAK T-TRAK Division Overview These Bus wires (feeders) are based on the NTRAK PowerPole RP. For additional information see the PowerPole information at www.ntrak.org or
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More information12V Dimmer Kit, version 2
12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control
More informationDigital temperature controllers
Digital Temperature Controller Using Thermocouple sunil kumar Adeeb Raza Digital temperature controllers are essential for temperature measurement and control of instrumentation in industries. These are
More informationVSOS VMOS. 100 WATT HIGH POWER STEREO VOLUME CONTROL w/override. 100 WATT HIGH POWER MONO VOLUME CONTROL w/override
VSOS 100 WATT HIGH POWER STEREO VOLUME CONTROL w/override VMOS 100 WATT HIGH POWER MONO VOLUME CONTROL w/override C US This ELAN Volume Control is NTRL certified to comply with local building codes. Use
More informationPoke-Home: Inverted Thru Board AWG: WTB INTER CONNECT FEATURES AND BENEFITS APPLICATIONS ELECTRICAL MECHANICAL ENVIRONMENTAL
AVX continues to develop innovative connectors for the industrial electronics market that provide significant benefits over existing, outdated connector solutions. Listening to the design engineering community,
More informationData Sheet GTD21148L SERIES 40W. (201) Switching Power Supplies
2. ELECTRICAL SPECIFICATIONS: INPUT VOLTAGE: INPUT CURRENT: OUTPUT VOLTAGE / CURRENT: MODEL: GTD21148L(M,H)-1703 GTD21148L(M,H)-2505 GTD21148L(M,H)-2506-X.X GTD21148L(M,H)-3009-X.X GTD21148L(M,H)-3512-X.X
More informationTroubleshooting Guide. MTS - type Systems for RV's
MOBILE THEATRE SYSTEM Troubleshooting Guide VERSION 1.1 For All MTS - type Systems for RV's River Park Inc. 21953 Protecta Dr Elkhart, In. 46516 (219) 522-7781 (219) 295-8780 www.riverparkinc.com 1 A.
More informationTELIKOU Intercom System
TELIKOU Intercom System DT-100 Desktop Station Instruction Manual 2006 TELIKOU Systems All Rights Reserved www.telikou.com While TELIKOU makes every attempt to maintain the accuracy of the information
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode (or SSB VOX mode) with no amplifier modifications. No amplifier T/R
More informationApplication Note #1245
Application Note #1245 ICM-1460-20W Interconnect Module with 20W Servo Drive The ICM-1460-20W (Rev D) Interconnect Module provides an on board 20W linear servo drive for the X-axis suitable for driving
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationCOPALUM Terminals and Splices (For Solid & Stranded Aluminum or Copper Wire)
Product Facts Bar Crimp Technique Terminals and Splices for aluminum-to-aluminum and aluminum-to-copper stripped wire applications Terminates stripped, stranded and solid (round or rectangular) aluminum
More informationPage 1 T O O L S A N D M AT E R I A L S R E Q U I R E D. 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T. A.
T O O L S A N D M AT E R I A L S R E Q U I R E D 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T A. Cabinet B. Wood Screw X4 C. Plastic wire connector x3 Page 1 I M P O R TA N T
More informationDigital Electronics & Chip Design
Digital Electronics & Chip Design Lab Manual I: The Utility Board 1999 David Harris The objective of this lab is to assemble your utility board. This board, containing LED displays, switches, and a clock,
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More informationFROM SCHEMATIC TO VEROBOARD
FROM SCHEMATIC TO VEROBOARD The circuit of a bench amplifier utilising a LM386 linear (integrated circuit) IC and a few other components is used for this tutorial. The schematic is shown below: First a
More informationRAM-34 RX Pre-amplifier System Installation and Operation Manual
RAM-34 RX Pre-amplifier System Installation and Operation Manual ( www.hamation.com ) RAM-34 Front and Rear Views Introduction The RAM-34 is a complete pre-amplifier system designed primarily for the low
More informationBOARD ASSEMBLY INSTRUCTION
BOARD ASSEMBLY INSTRUCTION Guide to the Evolution construction, I base model by Mauro Penasa Version 1.0. 08/07/2006 INTRODUCTION This document has the purpose to introduce some simple practical elements
More informationYana Dongles Tom Berger K1TRB (c)2016 v171227
Yana Dongles Tom Berger K1TRB (c)2016 v171227 These notes elaborate some items described in the Build notes, and add some more dongles enhancing Yana. Every effort has been exerted to save on the cost
More informationM-300 Mono power amplifier User s guide
M-300 Mono power amplifier User s guide M-300 Mono power amplifier User s guide Specifications: Contents: Power output: 8Ω: 290W, 0.01% THD SPECIFICATIONS Page 2 Input impedance: Gain: 4Ω: 580W, 0.01%
More informationConstruction of the "4 lines decoder for reading information contained in 406 beacon message
Construction of the "4 lines decoder for reading information contained in 406 beacon message Jean-Paul YONNET F1LVT / ADRASEC 38 F1LVT@yahoo.fr www.f1lvt.com We will describe the construction of the "four
More informationCloset Wall Drawer Unit
88 5531 751 Closet Wall Drawer Unit A. B. C. Shelf D. E. F. For assembly see instructions in carton 88 5531 752. 88 5531 752 Closet Wall Drawer Unit G. H. I. Plinth M. Bottom L. N. 2 pc. J. K. O. Drawer
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode (or SSB mode) with no amplifier modifications. No amplifier T/R relay
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationHendricks QRP Kits The Twofer Rev
Hendricks QRP Kits The Twofer Rev 1 11-15-06 1. Description The Twofer is a classic QRP transmitter that s easy to assemble and operate. It uses a JFET VXO (variable crystal oscillator), driver stage and
More information