User s Guide. MWTC/MWTC-D SERIES The Smart Connector TM. Wireless Thermocouple/ Connector/Transmitter/ Logger and Receivers

Transcription

1 RoHS 2 Compliant User s Guide Shop online at omega.com SM info@omega.com For latest product manuals: MWTC/MWTC-D SERIES The Smart Connector TM Wireless Thermocouple/ Connector/Transmitter/ Logger and Receivers

2 omega.com U.S.A. Headquarters: Servicing North America: Omega Engineering, Inc. Toll-Free: (USA & Canada only) Customer Service: (USA & Canada only) Engineering Service: (USA & Canada only) Tel: (203) Fax: (203) For Other Locations Visit omega.com/worldwide The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.

3 MTWC/MWTC-D Series - The Smart Connector TM Wireless Thermocouple/Connector/Transmitter/Logger & Receivers Table of Contents Section. Page Section 1 Introduction Precautions Safety Warnings and IEC Symbols Product Labeling Statement on FCC and CE Marking General Description & System Components Section 2 Hardware Package Inspection Included Items Section 3 Software Getting Started Software Installation USB Driver Installation MWTC Connector/Transmitter Setup Utility Program TC-Central Measurement and Recording Program Charting Tab Charting Options Data Logging Tab Menu Tabs Section 4 Transmitter/Connector Operation Setup and Configuration Mounting, Installation and Antenna Connection Thermocouple Connections Battery Installation or Replacement Section 5 Receiver Operation Mounting and Installation Section 6 System Operation Introduction RF Communication Basics Basic System Overview Connector/Transmitter Operation Receiver Operation Environment/Operating Conditions Determining and Maximizing Range Antenna Basics Antenna Placement Factory Preset Values Transmit Rate vs. Battery Life i

4 MTWC/MWTC-D Series - The Smart Connector TM Wireless Thermocouple/Connector/Transmitter/Logger & Receivers Section 7 Troubleshooting Connector/Transmitter Troubleshooting Receiver Troubleshooting LED Indications vs Operation Section 8 Service and Calibration Service and Calibration Section 9 Specifications Connector/Transmitter Specifications (Thermocouple Models) Receiver Specifications Section 10 Approvals & Regulatory Compliance FCC (Domestic Use: USA & Canada) International Usage & CE Marking (Pending) CE Declaration of Conformity (DOC) Patent Notice ii

5 MTWC/MWTC-D Series - The Smart Connector TM Wireless Thermocouple/Connector/Transmitter/Logger & Receivers Table of Figures Figure Description Page Section 1 Introduction Figure 1-1 IEC Symbols TC Connector Front Label Connector Rear Label MWTC-REC1 Receiver Front and Rear Labels System Components Section 3 Software Figure 3-1 Welcome Screen Select Install Screen Confirm Installation Screen License Agreement Screen Installation Complete Screen Welcome To The New Found Hardware Wizard Screen Install Software Automatically Wizard Screen Completing The New Found Hardware Wizard Screen Channels Tab Menu Screen TC-Central Program Screen Channel Configuration Configuration Channel Channel Display Box Charting Tab Menu Screen Charting Screen Start Data Logging/Plotting Screen Charting Options Screen Data Log TAB Screen Data Logging Screen Start Data Logging/Plotting Screen File Menu Tab View Menu Tab Tools Menu Tab Section 4 Connector Operation Figure 4-1 MWTC Overall Dimensions A Transmitter Programming Connection B Transmitter Programming Connector with Cable Installed Setup Mode Launch Setup Utility Program Welcome to Universal Wireless Screen Setup the Transmitter Screen Connect the Transmitter Screen Establish a Link Screen iii

6 MTWC/MWTC-D Series - The Smart Connector TM Wireless Thermocouple/Connector/Transmitter/Logger & Receivers Section 4 Connector Operation Continued Figure Description Page 4-9 Choose Options Screen Data Logging Options Menu Typical Data File Send Settings to The Transmitter Screen A LED Indications vs. Operations (MWTC-D) Mounting Bracket Installation Fresnel Zone Thermocouple Connection Recommended Thermocouple Placement Connector Battery Compartment Section 5 Receiver Operation Figure 5-1 Receiver Operation - Model UWTC-REC Mounting Installation Section 6 System Operation Figure 6-1 Basic System Overview Connector/Transmitter Button Operation Transmit and Low Battery Lights Receiver Indicator Lights Determining Maximum Range Operation In Buildings Horizontal Antenna Placement Vertical Antenna Placement Section 7 Troubleshooting Figure 7-1 LED Indications vs. Operations (MWTC-D) iv

7 Introduction 1 Section 1 - Introduction Please read this manual completely before installing and operating your wireless connector/transmitter and receiver system. It s important to read and follow all notes, cautions, warnings and safety precautions before operating this device. Device refers to your connector/transmitter or receiver unit. 1.1 Precautions This device is not designed for use in any medical or nuclear applications. Do not operate this device in flammable or explosive environments. Never operate with a power source other than the one recommended in this manual. This device has been designed for dry, moisture free indoor applications only. Do not operate this device outside the recommended use outlined in this manual. Any change made to the unit without the manufacturer s approval could void the user s authority to operate the equipment. No co-location with other radio transmitters is allowed. By definition, co-location is when another radio device or it s antenna is located within 20 cm of your connector/transmitter and can transmit simultaneously with your MWTC unit. Never install and/or operate your MWTC connector/transmitter closer than 20 cm to nearby persons. Never use your MWTC connector/transmitter as a portable device. Your unit has been designed to be operated in a permanent installation only. There are no user serviceable parts inside your device. Attempting to repair or service your unit may void your warranty: 1.2 Safety Warnings and IEC Symbols This device is marked with international safety and hazard symbols in accordance with IEC standards. It is important to read and follow all precautions and instructions in this manual before operating or commissioning this device as it contains important information relating to safety and EMC. Failure to follow all safety precautions may result in injury and or damage to your device. Use of this device in a manner not specified will void your warranty IEC symbols Description Caution, refer to accompanying documentation EU s Waste Electrical and Electronic Equipment Compliance 1-1

8 1 Introduction 1.3 Product Labeling Connector Front Label TC + TX LOW BATT TYPE WIRELESS THERMOCOUPLE CONNECTOR PRESS SETUP PRESS I / O MWTC Figure 1-2. TC Connector Front Label Connector Rear Label FCC ID: WR3-MWTC-2 IC:8205A-MWTC2! This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; 2) This device must accept any interference received, including interference that may cause undesired operation. OMEGA ENGINEERING, INC. Stamford, CT PATENTS & PATENTS PENDING omega.com Made in U.S.A. Figure 1-3. Connector Rear Label MWTC-REC1 Receiver Front and Rear Labels MWTC SERIES WIRELESS RECEIVER TX PWR! This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; 2) This device must accept any interference received, including interference that may cause undesired operation. omega.com OMEGA ENGINEERING, INC. Made Stamford, CT in U.S.A. Rear Label Front Label Figure 1-4. UWTC-REC1 Receiver 1-2

9 Introduction Statement on FCC and CE Marking FCC Marking FCC ID: WR3-MWTC-2 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference. 2.) This device must accept any interference received, including interference that may cause undesired operation CE Marking It is the policy of OMEGA to comply with all worldwide safety and EMI/ EMC regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. For additional information see Section 10 - Approvals & Regulatory Compliance. 1.5 General Description & System Components General Description Your Wireless Thermocouple/Connector Series features stand-alone, compact, battery powered wireless connectors that transmit their readings back to a host receiver up to 90 m (300 ) away. Each thermocouple unit is factory set to work as a type J, K, T, E, R, S, B, N or C calibration connector. When activated the connector will transmit readings continuously at a pre-set time interval that was programmed by the user during the initial setup. Each unit measures and transmits: Process Input Reading, Connector Ambient Temperature, RF Signal Strength and Battery Condition to the host and is displayed on the PC screen in real time using the provided software. When used with host receiver model MWTC-REC1 data from up to 48 wireless connectors can be received and displayed. Each unit includes free software that converts your PC into a strip chart recorder or data logger so readings can be saved and later printed or exported to a spread sheet file. MWTC-D is a wireless thermocouple connector/data logger. It can record up to process temperature data points or 32,700 process and ambient temperature data points locally. The recorded data can be downloaded to PC using the direct USB connection System Components USB RECEIVER CONNECTOR/TRANSMITTER MWTC SERIES WIRELESS RECEIVER TYPE TC TX + LOW BATT WIRELESS THERMOCOUPLE CONNECTOR PRESS SETUP PRESS I / O MWTC TX PWR Figure 1-5. System Components 1-3

10 2 Hardware Section 2 Hardware It is important that you read this manual completely and follow all safety precautions before operating this instrument. 2.1 Package Inspection Remove the packing list and verify that you have received all your equipment. If you have any questions about the shipment, please call our Customer Service Department at or We can also be reached on the Internet at omega.com, cservice@omega.com. When you receive the shipment, inspect the container and equipment for any signs of damage. Note any evidence of rough handling in transit. Immediately report any damage to the shipping agent. The carrier will not honor any damage claims unless all shipping material is saved for inspection. After examining and removing contents, save packing material and carton in the event reshipment is necessary. 2.2 Included Items The following items are supplied in the box. With Model MWTC Connector/Transmitter: 1 Connector/Transmitter 1 Type-K Thermocouple Sensor (Omega No. SC-GG-K PP) (MWTC models only) 1 Standard (AAA) 1.5V Lithium Battery, (Omega No. MWTC-A-BATT) for use with Model MWTC. 1 Mounting Bracket Kit 1 Micro-B USB Cable for MWTC-D (Data Logger) With Model MWTC-REC1, MWTC-REC5, or MWTC-REC6 Receiver: 1 Receiver Device 1 MWTC Series User s Manual (M-4721) 1 USB Interface Cable 1 TC-Central User Software CD 4 Rubber Enclosure Feet 1 MWTC Transmitter Programming Cable 2-1

11 Software 3 Section 3 Software 3.1 Getting Started The following program files are included on the MWTC User Software CD supplied with your Receiver. These files can also be downloaded from the omega.com website should you misplace your CD. MWTC Connector/Transmitter Setup Utility Program TC-Central Measurement and Data Logging Program 3.2 Software Installation System Requirements Your PC should meet the following minimum requirements: Pentium Class processor Hard Drive Space: 210 meg Ram: 256 meg or higher 1 Available USB Port 1 CD-ROM Drive Windows 2000, XP, Vista (32bit), or 7 Operating System Software Installation Insert the MWTC Series User CD that was included with your receiver unit into the CD-ROM drive on your PC. Your system should begin the installation process automatically. If the software installation does not start automatically please see the Troubleshooting Section 7. Figure 3-1. Welcome Screen This welcome screen should be visible on your computer screen. To continue with installing the program click the Next > button. 3-1

12 3 Software Figure 3-2. Select Install Screen From this screen you select the folder were you want the program files installed on your PC. The default setting will install the software under your Program folders in a new folder named Omega To continue with installing the program click the Next > button. Program folders in a new folder named Omega To continue with installing the program click the Next > button. Figure 3-3. Confirm Installation Screen The setup wizard now has all the information to complete the installation of the software on your PC. To continue with installing the program click the Next > button. 3-2

13 Software 3 From this screen you must select Agree to continue installing your program. After making your selection click the Next > button. The setup wizard will now install the software. Figure 3-4. License Agreement Screen Congratulations! You have just successfully installed the TC-Central Program on your PC. To end installing the program and close the setup wizard click the Close Button. From this screen you must select Agree to continue installing your program. After making your selection click the Next > button. The setup wizard will now install the software. Figure 3-5. Installation Complete Screen Congratulations! You have just successfully installed the WTC Central Program on your PC. To end installing the program and close the setup wizard click the Close button. 3-3

14 3 Software 3.3 USB Driver Installation To install the USB software drivers that are required for your MWTC system components to operate correctly follow these procedures. You need to have the TC-Central User Software CD that was supplied with your receiver loaded into the CD drive on your PC. 1. Connect your MWTC receiver to your computer with the USB cable provided in the box with your device. You should get a notice box that indicates that your computer Has Found New Hardware 2. Your computer will then launch the Found New Hardware Wizard. Follow the instructions indicated on the Wizard boxes and the additional instructions noted in this manual with each box. After completing the Found New Hardware Wizard your system will ask that you repeat this process. This is normal. You should repeat the steps outlined here twice. After the second driver is installed you should then get the New Hardware Ready For Use notice. Figure 3-6. Welcome To The Found New Hardware Wizard Screen From this box you should check the No, not at this time button. Then click the Next > button to continue with the driver installation process. 3-4

15 Software 3 Figure 3-7. Install Software Automatically Screen Next, check the Install the software automatically button. Then click the Next> button to continue. Figure 3-8. Completing The Found New Hardware Wizard Screen This screen will be displayed to indicate that the software drivers have been installed. You should click the Finish button to complete the process. 3-5

16 3 Software 3.4 MWTC Connector/Transmitter Setup Utility Program This utility is used to program your connector/transmitter for the following operating parameters: Channel Number, Sample Rate, and data logging (MWTC-D). For complete instructions on using this program please see Section TC-Central Measurement and Recording Program To launch the TC-Central program on your PC begin by accessing the Programs list under your Start Menu Next, scroll through the list of program folders to find the TC-Central folder. Inside the TC-Central folder click on the TC-Central program link. This will start the software running Channels TAB Menu CHANNELS TAB Figure 3-9. Channels TAB Menu Screen Channels Tab When TC-Central starts up, the Channels tab is displayed. This view allows you to see temperatures and properties for up to 12 connector/transmitter at one time 3-6

17 Software 3 Figure TC-Central Program This is a partial view of the TC-Central Program in operation. You will not have any blocks receiving data until you have programmed and placed into operation your connector/transmitters Setting up the TC-Central Program Before you can make wireless measurements with your connector/transmitter the TC-Central software must be configured properly. The following steps outline how to setup your program Channel Configuration Figure Channel Configuration From the Tools pull-down menu select Configure. Channel 1. This will open the program settings table were you can make selections on how you want your system to operate Figure Configuration Channel 1 ➀ Description Field 3-7

18 3 Software In the Description Field you can type a reference name that is associated with the location or process being measured by the connector/transmitter for address. Example.. Test Chamber 1 3-8

19 Software 3 2 Address Field Here you must set an address number into this box that corresponds to a matching Connector/Transmitter unit that you are using in your system. For the system to work correctly each Connector/Transmitter must have a number programmed that is different then other units in your system. Click with your mouse on the Up and Down buttons to advance to a higher or lower address number. 3 Display Timeout The Display Timeout setting is used to set how long you want the unit to continue showing the last reading data when communication between the Connector/Transmitter and receiver has been lost. Make sure not to set this value to a time less than the current sample rate programmed into the Connector/Transmitter or you will never receive and or display any readings. 4 Low Alarm / High Alarm When the High or Low Alarm box is checked the alarm feature becomes active. Click with your mouse on the Up and Down buttons to advance to a higher or lower setting. The displayed temperature reading will change to RED digits and begin blinking to indicate that the process temperature has gone below the low alarm or exceeded the high alarm value. 5 C or F Selecting the C or F button will configure the particular box to display readings in the desired units of measurement. 6 Hide When the Hide box is checked the particular box that you are configuring will become inactive and will not show up on the screen when running the TC-Central program. This is used to remove unused boxed when less than 12 Connector/Transmitter units are being used. 7 Sensor Offset Thermocouple Type Figure Channel Display Box 3-9

20 3 Software 3.6 Chart Tab CHART TAB Figure Chart TAB Menu Screen The Chart tab allows you to start, stop and view real-time data from the transmitters in a screen plot that you can save and print. Figure Charting Screen 1 Start Button The Start button will open the dialog box shown below. This box allows you to select one or more channels to be plotted. Click the checkbox next to the channel(s) number you want to include in your plot. Figure Start Data Logging/ Plotting Screen 3-10

21 Software 3 Line Color You can change the color specified for each channel s line. Click the Change button to select a new color for the Channel selected. Interval The total logging time is displayed for the interval setting selected. In general, the interval should normally be set to a value equal to or greater than the same sample time you programmed into the corresponding connector/ transmitter for that channel. You can choose to have the data logging/chart recording session end after 1000 data points, or have the session run continuously. After 1000 data points have been collected in the continuous mode, the oldest data point is shifted out on the left, and the newest data point is added to the right. Data will continue to be collected and displayed until you click on the Stop button above the chart. If you click the OK button, the data logging session will start, and Recording Data will flash in the status bar. The Start button above the chart will change to Stop, indicating that if you click it again, the logging session will be terminated. You can also start or stop a data recording session from the File menu. Once data has been collected, you can save it in a (*.csv) (comma separated values) file and open it in Microsoft Excel for further analysis. It is recommended that you Save As in Excel as a Microsoft Excel Workbook (*.xls). If you do not modify the (*.csv) version of the file, you can open it from TC Central s File menu, and display it in the chart and data log. 2 Clear Button The Clear button will delete all data from the chart and the data log. 3 Y Axis Control The Y Axis Min and Y Axis Max controls allow you to adjust the viewable range of temperatures to suit your particular application. The narrower the range between min and max, the more detail can be seen on the chart. 4 C or F Button The C or F button allows you to change the units of degrees displayed on the chart, and on the data logging. 3-11

22 3 Software 3.7 Charting Options You can access all of the charting options that are available by opening the chart option menu found under the View Tab. See below. Figure Charting Options Screen Zoom In/Zoom Out Allow you to change the size of the chart on the screen. You can also use the Control-Up Arrow and Control-Down Arrow keys as well. Default Chart Size Returns the chart to its normal size (after zooming or panning), and places the title and legend in their normal positions. Reset Axes Reset Axes will effectively cancel the results of a Data Zoom and return the axes back to their original dimensions, but will not change the size of the chart. Chart (Mouse) Zoom Perform the same function as mentioned above, by moving the mouse up or down, or rolling the mouse wheel. Data (Box) Zoom When checked, you can use the mouse to click and drag a rectangle around a line of data to magnify that portion of the chart. The chart size will remain the same, but the axes will be expanded as well and the data line(s) to allow viewing more detail. You can close either of the axis scroll bars by clicking on the Red button of each scroll bar. Pan 3-12

23 Software 3 Allows you to move the chart as well as the title and legend around on the screen. If the Pan item is checked, you can still use the mouse wheel to zoom in and out, while holding the left button down to move the chart as desired. Reset Axes will effectively cancel the results of a Data Zoom and return the axes back to their original dimensions, but will not change the size of the chart. Floating Cursor When checked, will display a crosshair type cursor that you can move with the mouse. You can use the Floating Cursor to pinpoint a particular temperature and time. The status bar displays the data point number, the time, and the temperature, where the crosshairs meet. If the horizontal cursor line is touching a data plot line, the corresponding channel number is also displayed in the status bar. Tracking Cursor When checked, will perform similarly to the Floating Cursor, except that you can specify a channel for the horizontal cursor line to lock on to. This channel is also displayed in the status bar. With this option enabled, you can move the mouse left and right without regard to up and down, and the horizontal cursor will remain pointing to the line (channel) you specify. Assuming you have more than one channel plotted on the chart, you can switch tracking to another channel by moving the mouse over the data line of that channel until the mouse cursor becomes a hand with a pointing finger. If you left-click at this point, the Tracking Cursor will track that line. You can also change the channel of the Tracking Cursor from the chart s context menu, Tracking Cursor menu item combo box. The same option is also available in the View Chart menu in the main menu bar Line Options Allows you to select which channel(s) you want to display, and/or change the color of each channel data line. This allows you to limit your view to either a single channel, or a selected two or more channels for comparison, instead of having all twelve channels displayed at once. 3-13

24 3 Software 3.8 Data Log Tab DATA LOG TAB Figure Date Log TAB Screen The Data Log tab allows you to view received data from a connector/ transmitter in a table format as it is being recorded. This data can be saved and printed Figure Data Logging Screen ➀ Start Button The Start button will open the dialog box shown below. This box allows you to select one or more channels to be plotted. Click the checkbox next to the channel(s) number you want to include in your plot Figure Start Data Logging/Plotting Screen

25 Software 3 Line Color You can change the color specified for each channel s line. Click the Change button to select a new color for the Channel selected. Interval The total logging time is displayed for the interval setting selected. In general, the interval should normally be set to a value equal to or greater than the same sample time you programmed into the corresponding connector/ transmitter for that channel. You can choose to have the data logging/chart recording session end after 1000 data points, or have the session run continuously. After 1000 data points have been collected in the continuous mode, the oldest data point is shifted out on the left, and the newest data point is added to the right. Data will continue to be collected and displayed until you click on the Stop button above the chart. If you click the OK button, the data logging session will start, and Recording Data will flash in the status bar. The Start button above the chart will change to Stop, indicating that if you click it again, the logging session will be terminated. You can also start or stop a data recording session from the File menu. Once data has been collected, you can save it in a (*.csv) (comma separated values) file and open it in Microsoft Excel for further analysis. It is recommended that you Save As in Excel as a Microsoft Excel Workbook (*.xls). If you do not modify the (*.csv) version of the file, you can open it from TC Central s File menu, and display it in the chart and data log. 2 Clear Button The Clear button will delete all data from the data log. 3 Adjust Button Resizes the columns to the smallest size necessary to fit all the data in the columns. 4 C or F Button The C or F button allows you to change the units of degrees displayed during the data logging. 5 Auto Scroll Rows The Auto Scroll Rows checkbox causes the data to be scrolled up one line each time a new row of data is added to the grid. 3-15

26 3 Software 3.9 Menu Tabs File Menu Figure File Menu Tab Open Displays a dialog box which allows you to choose a data file to open and display on the chart and in the data log. This file must be a file that was saved by the Save menu item in TC Central. If the file has been modified externally, you may not be able to open it. Save Displays a dialog box which allows you to save the data currently displayed on the chart and in the data log. The file format is (*.csv) (comma separated values), which can be opened by Microsoft Excel for further analysis and charting. It is strongly recommended that you do not modify this file, or you may not be able to open it again in TC Central. Use Excel s Save As option to save it as a Microsoft Excel Workbook (*.xls), which you can then modify. Start Data Recording Performs the same function as the Start button on the Chart and Data Log Tabs. A dialog box is displayed allowing you to select one or more channels to be plotted and logged by checking the checkbox next to the channel number. You can also change the color of each channel s line. The interval should be set as desired for your particular needs. The total logging time is displayed for the interval setting selected. In general, the interval should normally be set to a value equal to or greater than the Seconds per Sample you configured into the transmitter using the MWTC Configuration Wizard. You can choose to have the data logging/chart recording session end after 1000 data points, or have the session run continuously. After 1000 data points have been collected in the continuous mode, the oldest data point is shifted out on the left, and the newest data point is added to the right. Data will continue to be collected and displayed until you click on the Stop button above the chart, above the Data Log, or select Stop Data Logging from the File menu. If you click the OK button, the data logging session will start, and Recording Data will flash in the status bar. The Start button above the chart and data 3-16

27 Software 3 log will change to Stop, indicating that if you click it again, the logging session will be terminated. Stop Data Logging Performs the same function as the Stop buttons on the Chart and Data Log Tabs, by terminating any data logging/plotting session in progress. Export Chart Displays a dialog box that allows you to either save an image of the current chart on the Chart Tab, or copy it to the clipboard. Print Preview Displays a standard Windows Print Preview dialog, allowing you to view the item(s) as they would be printed on a printer. You can also print from this dialog by clicking the printer icon in the upper left corner. If the Channels Tab is displayed before choosing this option, a screen snapshot of the Channels Tab will be previewed. If the Chart Tab is displayed before choosing this option, the current chart image will be previewed. If the Data Log Tab is displayed, the data table in grid style format will be previewed. Page Setup Displays a standard page setup dialog box which allows you to change the page orientation, margins, paper size, etc. You can then select the Print Preview menu to view your changes without printing. Print Displays a standard print dialog box. This allows you to select printers, printer preferences, page ranges, number of copies, etc. If you click the Print button, the specified page(s) will be sent to the printer. If you click the Apply button, you can then select the Print Preview menu to view your changes without printing. Exit Will exits and close the TC-Central program View Menu Tab Figure View Menu Channels 3-17

28 3 Software Performs the same functions as the Channels context menu, except for the Configure menu item. See Channels TAB Menu (Section 3.9) for an explanation of this menu. Chart Performs the same functions as the Chart context menu. See Chart Tab Menu (Section 3.6) for an explanation of this menu. Data Log Performs the same functions as the Auto Scroll Rows checkbox and the Adjust button on the data log. See Data Log Menu (Section 3.8) for an explanation of these functions Tools Menu Figure Tools Menu Tab Configure Displays the same dialog box as the Channels context menu, Configure menu item, after you select a channel to configure. See Channels Tab above for an explanation of this dialog box. Auto Connect Receiver Normally disabled, if you have established communications with a receiver connected to your PC. If for some reason such as the receiver being replaced with a different one, this menu item will be available. When selected, TC Central will send +++ to each and every available COM port in an attempt to identify a port with a receiver connected to it. If TC Central finds a receiver, it will perform the necessary configuration of the receiver and display the COM port number in Green in the status bar. Even though your receiver is connected via a USB Cable, the USB drivers installed create a virtual COM port, usually a port number greater than COM4. Once connected, TC Central 3-18

29 Software 3 Manual Connect Receiver Is available if you do not want TC Central to send +++ to all of your serial ports. If you know the COM port number used by your receiver, you can connect to it from this menu without disturbing other COM ports. You can also use this menu to connect to a second receiver connected to the PC on a different COM port. Configure Transmitter Launches the UWTC Configuration Wizard. When you follow the steps in the wizard, you will be able to configure each transmitter (one at a time) for the thermocouple type, the transmitter address, and the sample rate. 3-19

30 4 Transmitter Operation Section 4 Transmitter/Connector Operation Figure 4-1 shows the general dimensions (0.6) 82.5 (3.25) 25.4 (1.0) FEMALE UNI-CONNECTOR ACCEPTS STANDARD MALE OSTW OR MINIATURE MALE SMPW MATING CONNECTIONS DIMENSIONS mm (in) MWTC-D USB PORT Figure 4-1. MWTC Overall Dimensions 4-1

31 Connector Operation Setup and Configuration Connecting Your Device Connect the USB programming cable to your connector/transmitter unit and also to an available USB port on your computer. See figures below. This cable was provided in the box with your receiver unit. For the MWTC-D, the USB cable is included with the transmitter. Simply connect the cable to the USB connector on the side of the transmitter (you do not need to open the unit) and into an available USB port on your PC, see Fig Connecting Your Programming Cable Figure 4-2A. Transmitter Programming Connection 3 Figure 4-2B. Transmitter Programming Connector with Cable Installed (1) Programming Connector (2) Battery (3) Programming Cable 4-2

32 4 Connector Operation Configure Your Connector/Transmitter Now that you have connected your USB cable to your PC and connector transmitter you will complete the following steps to configure your connector/ transmitter before placing the unit into operation. You will be using the configuration software utility that you installed onto your PC in Section 3.2. If you have not installed the configuration software utility you should do so now. During this procedure you will be setting the following parameters in your connector transmitter. Address Number This sets a unique address number into your connector/transmitter. Later, when you set up your measurement software you will again set channel numbers to receive readings from the corresponding unit(s). Each connector must be set for a different address number for your system to operate correctly. If you will be using more than one receiver unit in your area it is important to set the connector/transmitter address numbers to be a corresponding number in your TC-Central software. See Examples below. For the first receiver: Set the addresses on your connector/transmitters to 101, 102, 103, 104, etc. Then set the channels in your TC-Central user software to match. For the second receiver: Set the addresses on your connector/transmitters to 201, 202, 203, 204, etc. Then set the channels in your TC-Central user software to match. This numbering scheme can be expanded to match the number of receivers you are using. In addition RF Channel Frequency should be different, between 1st and 2nd receivers. Sample Rate (Recording Interval) This will program your device to transmit 1 data reading to your receiver at a specified time interval. Available settings are 2, 3, 4, 5, 10, 15, 30, 45, 60, 75, , or 120 seconds. The same sampling rate is used for recording interval on MWTC-D. RF Channel You can set RF Channel Frequency between Channels A, B, C. Channel Logging Option For MWTC-D you can set additional parameters for data logging option. The sample rate you set will have the most direct effect on the life of the battery in your connector/transmitter. It is recommended that you set the longest sample time that your application can live with to extend time between battery replacement. See Section 6 for more information on battery life. 4-3 STEP 1. Enter the SETUP mode. To place your connector/transmitter into the SETUP mode for programming follow this procedure.

33 Connector Operation 4 TYPE TC TX + LOW BATT WIRELESS THERMOCOUPLE CONNECTOR PRESS SETUP PRESS I / O MWTC SETUP BUTTON ON/OFF BUTTON Figure 4-3. Setup Mode Press and hold the ON/OFF button. While the ON/OFF button is being held, press the SETUP button one time and then release the ON/OFF button. The green (TX) indicator on the front of your device should be blinking at a steady rate. This indicates your connector/transmitter is ready to run the configuration utility software. STEP 2. Launch Setup Utility Program. To launch the MWTC Connector/Transmitter setup utility program on your PC begin by accessing the Programs list under your Start Menu. Scroll through the list of to find the TC-Central folder, then select the MWTC Configuration Program. Figure 4-4. Launch Setup Utility Program 4-4

34 4 Connector Operation STEP 3. Programing your settings into a connector/transmitter. Figure 4-5. Welcome To Universal Wireless Screen After starting the setup utility program this will be the first screen you will see. Click the Next > button to proceed and continue setting up your connector/ transmitter. Each screen will provide instruction details on how to proceed. Figure 4-6. Setup The Transmitter Screen If you have not already placed your connector/transmitter into the Setup mode you should do this now before continuing. After your unit has been placed into the Setup mode click the Next > button to proceed and continue setting up your connector/transmitter. 4-5

35 Connector Operation 4 Figure 4-7. Connect The Transmitter Screen If you have not already connected your connector/transmitter to a USB port on your PC you must do this now before continuing. After your unit has been connected click the Next > button to proceed and continue setting up your connector/transmitter. Figure 4-8. Establish A Link Screen After successful communication between your connector/transmitter has been established you can click the Next > button to proceed and continue setting up your connector/transmitter. If you did not receive this confirmation of proper communication you should click the Back button to try connecting again. If you still do not obtain a good connection visit the Troubleshooting Section of this users guide for addition. 4-6

36 4 Connector Operation Figure 4-9. Choose Options Screen From this screen you will select the main operating settings for your connector/transmitter. Start by selecting the address setting for this unit. (Note: Each connector/transmitter must have a different address number than other units in your system for proper operation). Then select the sample rate that your unit will transmit data to the receiver. RF Channel Selection Here you can select from 3 channels choices, this gives you the flexibility to change the transmitting frequency should you have interference from other devices close to your system, or using multiple wireless receivers (MWTC- REC1 or MWTC-REC5 or MWTC-REC6). If you have MWTC-D, click on the Data Logging Options button to set additional parameters as follows: Start Logging: You can start the recording process either at Power up (When the unit is turned on), or at a preset time & date. When the unit is set for preset time & date, it will automatically turns itself on and starts to log and or transmit at the specified time & date. Engineering Unit: You can select your Engineering unit from Deg F,C,K, and R. Recording Selection: You can select from recording Process temperature or Process & ambient temperatures. Mode of Operation: You can select from Wireless only, Record only, or Wireless & Recording combined. You can also download selected data files (Up to 8 files) from the connector. A typical data file is shown in figure You can erase data files from the connector. 4-7 MWTC-D can store up to 8 separate data files. When reached the end of the memory or 8 data files, it will stop recording and the red and green LEDs will blink alternately. In order to start the recording process again, you need to download the data files to PC and then erase from the connector.

37 Connector Operation 4 Figure Data Logging Options Menu Figure Typical Data File 4-8

38 4 Connector Operation Figure Send Settings To Transmitter Screen Congratulations! You have successfully programmed your connector transmitter. After your unit has been programmed click the Finish button to close the utility program or click the Start button to begin setting up a second unit. You can now disconnect your connector transmitter from the programming cable. Press the Setup button on the connector/transmitter one time to exit the Setup mode Here are the default settings for the MWTC-D Wireless Transmitter/Logger Recording / sampling interval = 5 seconds Start Logging at = Power Up Engineering unit = Deg F Recording Selection = Process and Ambient Temperature Mode of operation = Wireless Only When operating the MWTC-D for the first time, or every time the battery is replaced, you need to configure the unit using the End Device Configuration Wizard program. It allows you to set up logging parameters such as current time & date, recording interval, Start Logging Mode, Recording selection, and mode of operation. The current Time & Date is lost when the battery is removed. 4-9

39 Connector Operation 4 Here is a Figure 4-12A showing the operation status vs. the LED indications for MWTC-D: Operation Status Open Sensor Input Wireless Transmission, when pressing I/O key Logging Mode, when pressing I/O key Wireless & Logging Mode combined, when pressing I/O key interval Turning the unit off Press I/O key Low Battery Low Battery Open Sensor Input Memory Full Logging Mode Memory Full Wireless and Logging Mode combined LED Indications Red LED blinks immediately after every Green LED blink Green LED blinks every transmission interval Red LED blinks once, then the Green LED blinks every recording interval Red LED blinks twice, then the Green LED blinks every transmission/recording Red LED blinks three times Red & Green LED blinks together every transmission/recording interval Red & Green LED blinks together every transmission/recording interval followed by one more Red LED blink Red & Green LED blinks alternately 5 times followed by 3 Red LED blinks indicating the unit is off Red & Green LED blinks alternately 5 times times followed by Green LED blinking every transmission interval. Logging stops. Set Up/ Configuration Mode Press Green LED blinks continuously every 0.5 and Hold I/O key, then press Set up seconds key, then release both keys Figure 4-12A. MWTC-D Operation Status vs. LED Indicator 4.2 Mounting, Installation and Antenna Connection Mounting Bracket Installation A mounting bracket kit has been supplied with your connector/transmitter. The diagram below shows dimensions and how to install your mounting bracket. 4-10

40 PRESS PRESS 4 Connector Operation TIP: Use the plate as a template to mark the location of the mounting holes you need to drill before installing the mounting kit onto the connector transmitter. MOUNTING BRACKET MOUNTING SCREW SPACER MWTC UNIT - TC + TYPE TX WIRELESS THERMOCOUPLE CONNECTOR LOW BATT MWTC PRESS SETUP PRESS I/0 Figure Mounting Bracket Installation Mounting When mounting your connector/transmitter, care should be taken to make sure it is as far away from any metal objects. If nearby metal gets too close to your connector/transmitter, it has the potential to interfere with the way the unit radiates and may cause signal lose or possibly even the inability to communicate at all with your receiver Installation When installing your connector/transmitter it is important to position your device in such a way as to optimize the antenna location within what s known as the Fresnel Zone. The Fresnel Zone can be thought of as a football-shaped invisible tunnel between two locations that provides a path for RF signals between your connector/transmitter and your receiver. TYPE TC TX + LOW BATT WIRELESS THERMOCOUPLE CONNECTOR MWTC SETUP I / O FRESNEL ZONE RECEIVER ANTENNA Figure Fresnel Zone 4-11

41 Connector Operation 4 In order to achieve maximum range, the football-shaped path in which radio waves travel must be free of all obstructions. Obstacles in the path (especially metal) will decrease the communication range between your connector/ transmitter and receiver. Also, If the antennas are mounted just barely off the ground, over half of the Fresnel zone ends up being obstructed by the earth resulting in significant reduction in range. To avoid this problem, the antennas should be mounted high enough off of the ground so that the earth does not interfere with the central diameter of the Fresnel zone. It is important to understand that the environment may change over time due to new equipment or machinery being installed, building construction, etc. If new obstacles exist between your connector/transmitter and receiver, the devices can be raised on one end or on both ends to hopefully clear the Fresnel Zone of obstructions. No co-location with other radio transmitters is allowed. By definition, co-location is when another radio device or it s antenna is located within 20 cm of your connector/ transmitter and can transmit simultaneously with your MWTC unit. Never install MWTC connector/transmitters within 20 cm or less from each other Antenna Use of any other antenna then what s supplied with your device will void all FCC regulatory compliance. Additional Information on installation and system operation can be found in Section

42 4 Connector Operation Thermocouple Connections Your connector/transmitter has been design with a patented universal input that will interface with most industry thermocouple connectors. Omega s Miniature (SMP) Series and Standard (OST) Series of connectors will plug directly into the side of your unit. Omega s line of thermocouple probes with connectors attached will also plug directly into your unit. Universal input accepts standard and miniature connectors. Figure Thermocouple Connection Thermocouple Operating Environment and Placement Ambient Temperature Concerns Your Connector/Transmitter is rated for use in ambient temperatures between -10 to 70 C (14 to 158 F). Exposure to temperatures below or above these stated temperatures can cause your device to malfunction and produce incorrect operation. When installing your thermocouple probe care should be taken to make sure your connector/transmitter will not be operated in an environment outside the specifications outlined in Section Recommended Placement For applications were the ambient temperature around the thermocouple probe has the possibility of exceeding the operating conditions outlined in Section 9 of this manual, the connector/transmitter should be mounted away from the thermocouple probe in an area within the normal operating conditions of -10 to 70 C (14 to 158 F). See Below

43 TC LOW BATT TYPE WIRELESS THERMOCOUPLE CONNECTOR PRESS SETUP PRESS I / O Connector Operation 4 THERMOCOUPLE MEASUREMENT AREA SAFE AMBIENT AREA CONNECTOR/TRANSMITTER + TX MWTC THERMOCOUPLE PROBE MATING CONNECTOR Figure Recommended Thermocouple Placement CAUTION: Installing your connector/transmitter in an application were the device will be exposed to ambient temperatures above or below the operating limits specified in this manual will damage your unit and cause the unit to malfunction and produce incorrect operation. 4.4 Battery Installation or Replacement Model MWTC-(*)-915 To install or replace the battery in your Connector/Transmitter you must first remove the two screws located on the back side of your device. This will allow you to access the battery compartment. + - BATTERY (NOTE POLARITY) Figure Battery Compartment 4-14

44 4 Connector Operation Lithium batteries may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Be sure to follow the safety warnings listed below: Your MWTC Transmitter operates with one 1.5V AAA Lithium Battery. Omega Replacement Part Number MWTC-A-BATT. Never operate your MWTC transmitter with a different battery than what is specified in this manual or on the MWTC data sheet. Do not discharge the battery using any device except your MWTC Transmitter unit. When the battery is used in devices other than the specified device, it may damage the battery or reduce its life expectancy. If the device causes an abnormal current to flow, it may cause the battery to become hot, explode or ignite and cause serious injury. Refer to the Omega technical data sheet or this manual for the temperature ranges over which the battery can be operated. Use of the battery outside this temperature range may damage the MWTC Transmitter or reduce the performance and life of the battery. Do not place the battery in fire or heat the battery. Do not store batteries with other hazardous or combustible materials. Do not install the battery backwards so the polarity is reversed. Do not connect the positive terminal and negative terminal of the battery to each other with any metal object (such as wire). Do not carry or store the battery together with metal objects. Do not pierce the battery with nails, strike the battery with a hammer, step on the battery or otherwise subject it to strong impacts or shocks. Do not solder directly onto the battery. Do not expose battery to water or salt water, or allow the battery to get wet. Do not disassemble or modify the battery. When the battery is discharged, insulate the terminals with adhesive tape or similar materials before disposal. Immediately discontinue use of the battery if, while using or storing the battery, the battery emits an unusual smell, feels hot, changes color or shape, leaks or appears abnormal in any other way. Contact Omega if any of these problems are observed. Do not place the battery in microwave ovens or high-pressure containers. Always dispose of discharged batteries in accordance with all local, state and national laws. Immediately discontinue use of the battery if, while using or storing the battery, the battery emits an unusual smell, feels hot, changes color or shape, leaks or appears abnormal in any other way. Contact Omega if any of these problems are observed. Do not place the battery in microwave ovens, high pressure containers. Always dispose of discharged batteries in accordance with all local, state and national laws. 4-15