EMC Test Report. Report No.: AGC EE01 EN V1.9.2: 2011 EN V1.3.1: 2002

Transcription

1 Page 1 of 45 EMC Test Report Report No.: AGC EE01 PRODUCT DESIGNATION BRAND NAME TEST MODEL CLIENT : Two way radio : Retevis : RT22 : HENAN ESHOW ELECTRONIC COMMERCE CO., LTD DATE OF ISSUE : Dec.30, 2016 STANDARD(S) : EN V1.9.2: 2011 EN V1.3.1: 2002 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

2 Page 2 of 45 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Dec.30, 2016 Valid Extension Report Note: The original test report Ref.No.AGC EE01 dated , was modified on to include the following changes: - Change brand name; - Change model name; - Change the name and address of the applicant; - Change the name and address of the manufacture; - Change the appearance of EUT.

3 Page 3 of 45 TABLE OF CONTENTS 1. GENERAL INFORMATION EUT DESCRIPTION TEST METHODOLOGY UNIT OF MEASUREMENT ANTENNA DECISION OF TEST MODE INSTRUMENT AND CALIBRATION MEASURING INSTRUMENT CALIBRATION FACILITIES AND ACCREDITATIONS FACILITIES EQUIPMENT SETUP OF EQUIPMENT UNDER TEST SETUP CONFIGURATION OF EUT SUPPORT EQUIPMENT TEST SETUP ETSI EN /-5 REQUIREMENTS RADIATED EMISSION AC MAINS LINE CONDUCTED EMISSION AC MAINS HARMONIC CURRENT EMISSION AC MAINS VOLTAGE FLUCTUATION AND FLICKER ELECTROSTATIC DISCHARGE RF ELECTROMAGNETIC FIELD AC MAINS FAST TRANSIENTS COMMON MODE AC MAINS SURGE AC MAINS RF COMMON MODE VOLTAGE DIPS AND INTERRUPTION APPENDIX 1: PHOTOGRPHS OF TEST SETUP APPENDIX 2: PHOTOGRPHS OF EUT... 39

4 Page 4 of GENERAL INFORMATION Applicant Address Manufacturer Address Product Designation Brand Name Model Name HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Room 722, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China Shenzhen Retevis Technology Co., Ltd Room 700, 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Buji Street, Longgang District, Shenzhen, China Two way radio Retevis RT22 Date of Test Aug.06, 2016 to Aug.09, 2016 Test Result Pass The above equipment was tested by Attestation Of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in ETSI EN and ETSI EN The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Tested By Steven Zhou(Zhou Pengyun) Dec.30, 2016 Reviewed By Stone Zhou(Zhou Dong) Dec.30, 2016 Approved By Solger Zhang(Zhang Hongyi) Authorized Officer Dec.30, 2016

5 Page 5 of EUT DESCRIPTION Product Designation Brand Name Test Model Hardware Version Software Version Modulation Channel Separation Operation Mode Antenna gain Rated Output Power Antenna Designation Power Supply Two way radio Retevis RT22 N/A N/A FM 12.5 KHz Push to talk 1.5dBi 3W (It was fixed by the manufacturer, any individual can t arbitrarily change it) Inseparable DC 3.7V, 1000mAh by battery Note: For more details, refer to the user s manual of the EUT.

6 Page 6 of TEST METHODOLOGY All tests were performed in accordance with the procedure documented in ETSI EN V1.9.2 ( ) as referenced in ETSI EN V1.3.1 ( ). 3.1 UNIT OF MEASUREMENT Measurements of radiated interference are reported in terms of db(uv/m) at a specified distance. The indicated readings on the Spectrum analyzers were converted to db (uv/m) by use of appropriate conversion factors. Measurements of conducted interference are reported in terms of db(uv). The field strength is calculated by adding the Antenna Factor and Cable Factors and subtracting the Amplifier Gain from the measured reading. The following is a sample calculation: FS = RA + AF + CF - AG Where FS = Field Strength RA = Receiver Amplitude AF = Antenna Factor CF = Cable Attenuation Factor AG = Amplifier Gain Assume a receiver reading of 52.5 dbuv is obtained. The Antenna Factor of 7.4dB/m and a Cable Factor of 1.1dB are added. The Amplifier Gain of 29 db is subtracted, giving field strength of 32 dbuv/m. The 32-dBuV/m values was mathematically converted to its corresponding level in uv/m. FS = = 32 dbuv/m Note: Level in uv/m = Common Antilogarithm [(32 dbuv/m)/20] = 39.8 uv/m 3.2 ANTENNA The calibrated antennas used to sample the radiated field strength are mounted on a non-conductive, motorized antenna mast 3 meters from the leading edge of the turntable. 3.3 DECISION OF TEST MODE Mode 1 Charging Mode Mode 2 Operate in TX Mode Mode 3 Operate in RX Mode Mode 4 Standby Mode Note: All the modes had been test, but only the worst data was recorded in the report.

7 Page 7 of INSTRUMENT AND CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. The uncertainty is calculated using the methods suggested in the Guide to the Expression of Uncertainty in Measurement (GUM) published by ISO. - Uncertainty of Conducted Emission, Uc = ±2.75dB - Uncertainty of Radiated Emission, Uc = ±3.2dB

8 Page 8 of FACILITIES AND ACCREDITATIONS 5.1 FACILITIES Site Location Attestation of Global Compliance (Shenzhen) Co., Ltd B112-B113, Building 12, Baoan Building Materials Center, No.1 of Xixiang Inner Ring Road, Baoan District, Shenzhen, Guangdong, P.R.China 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with preselectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods.

9 Page 9 of SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Device Type Brand Model Series No. Data Cable Power Cord 1. Adapter N/A KC-N85BB1-V Charger N/A KC-ZCR Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use. 6.3 TEST SETUP The equipment under test was configured and operated in a manner of normal operation. EUT tended to maximize its emission characteristics in a typical application for conducted and radiated emission measurement. The RF module plus ancillary (stand alone unit) was evaluated as per table 2 of clause 7.1 of ETSI EN Software Used During the Test Operating System -- File Name -- Program Sequence -- RF Management Software -- Remark: During the test, no modification is made to the EUT to comply with Class B limit levels.

10 Page 10 of ETSI EN /-5 REQUIREMENTS 7.1 RADIATED EMISSION LIMIT Please refer to ETSI EN Clause 8.2.3, Table 3 and EN Clause 6, Table 6, Class B MEASUREMENT EQUIPMENT USED Radiated Emission Test Site # 4 Name of Equipment MANUFACTURER MODEL SERIAL NUMBER Cal. Date Cal. Due EMI TEST RECEIVER R&S ESPI N/A SPECTRUM ANALYZER AGILENT N9010A MY Multi-Device Controller EMCO 2090 N/A AMPLIFIER Schwarzbeck BBV ANTENNA R&S VULB9168 D Double-Ridged Waveguide Horn ETS LINDGREN RF CABLE SUIRONG 30MHZ-18GHZ N/A Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION

11 Page 11 of 45 TEST PROCEDURE Please refer to ETSI EN Clause and EN Clause 6 for the measurement methods. TEST RESULTS (OPERATE IN MODE 1) 30MHZ-1GHZ Test Result of Radiated Emission Test Horizontal Factor Level Limit Frequency Reading Margin Height Angle Polarization db db(uv/m) db(uv/m) Pass/Fail MHz db(uv) db cm deg (1/m) PK QP H Pass H Pass H Pass H Pass H Pass H Pass RESULT: PASS

12 Test Result of Radiated Emission Test Vertical Report No.: AGC EE01 Page 12 of 45 Factor Level Limit Frequency Reading Margin Height Angle Polarization db db(uv/m) db(uv/m) Pass/Fail MHz db(uv) db cm deg (1/m) PK QP V Pass V Pass V Pass V Pass V Pass V Pass RESULT: PASS

13 Page 13 of 45 TEST RESULTS (ABOVE 1GHZ) Test Result of Radiated Emission Test Horizontal Factor Level Limit Margin Frequency Reading Height Angle Polarization db db(uv/m) db(uv/m) db Pass/Fail MHz db(uv) cm deg (1/m) PK PK PK H Pass H Pass H Pass H Pass H Pass H Pass RESULT: PASS

14 Page 14 of 45 Test Result of Radiated Emission Test Vertical Factor Level Limit Margin Frequency Reading Height Angle Polarization db db(uv/m) db(uv/m) db Pass/Fail MHz db(uv) cm deg (1/m) PK PK PK V Pass V Pass V Pass V Pass V Pass V Pass RESULT: PASS

15 Page 15 of AC MAINS LINE CONDUCTED EMISSION LIMIT Please refer to ETSI EN Clause 8.4.3, Table 8 and EN Clause 5, Table 2, Class B MEASUREMENT EQUIPMENT USED Conducted Emission Test Site # 3 Name of Equipment Manufacturer Model Serial Number Calibration Date Calibration Due EMI Test Receiver R&S ESCI LISN R&S ESH3-Z CE CABLE SUIRONG 9KHZ-30MHZ N/A Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION Vert. reference plane EMI receiver EUT LISN Reference ground plane TEST PROCEDURE Please refer to ETSI EN Clause and EN Clause 5 for the measurement methods. TEST RESULTS (OPERATE IN MODE 1)

16 Page 16 of 45 CONDUCTED EMISSION TEST L1 RESULT: PASS

17 Page 17 of 45 CONDUCTED EMISSION TEST N RESULT: PASS

18 Page 18 of AC MAINS HARMONIC CURRENT EMISSION 7.3.1LIMITS OF HARMONIC CURRENT NOTE: Limits for Class A Equipment Harmonics Order n Max. permissible harmonic current (A) Odd harmonics n /n Even harmonics n /n 1. According to section 5 of EN : 2000, the EUT is Class A equipment. 2. The above limits are for all applications having an active input power>75w. No limits apply for equipment with an active input power up to and including 75W TEST PROCEDURE 1.1 The EUT was placed on the top of a wooden table 0.8 meters above the ground and operated to produce the maximum harmonic components under normal operating conditions for each successive harmonic component in turn. 1.2 The correspondent test program of test instrument to measure the current harmonics emanated from EUT is chosen. The measure time shall be not less than the necessary for the EUT to be exercised.

19 Page 19 of 45 MEASUREMENT EQUIPMENT USED Equipment Manufacturer Model S/N Cal. Date Cal. Due Signal Conditioning Unit Schaffner CCN AC Source Schaffner NSG TEST SETUP Test T EU 80c For the actual test configuration, please refer to Appendix II:Photographs of the Test Configuration. TEST RESULT Test Specification Test Frequency: 50Hz Test Voltage: 230Vac Waveform: Sine Test Time: 2.5min Classification: Class A NOTE: 1. The active input power of the EUT is less than 75W. 2. No limits apply for equipment with an active input power up to and including 75W.

20 Page 20 of AC MAINS VOLTAGE FLUCTUATION AND FLICKER LIMITS OF VOLTAGE FLUCTUATIONS AND FLICKER Test Item Limit Note P st 1.0 P st means Short-term flicker indicator P lt 0.65 P lt means long-term flicker indicator T dt 0.5 T dt means maximum time that d t exceeds 3% d max (%) 4% d max means maximum relative voltage change. d c (%) 3.3% d c means relative steady-state voltage change. MEASUREMENT EQUIPMENT USED Equipment Manufacturer Model S/N Cal. Date Cal. Due Signal Conditioning Unit Schaffner CCN AC Source Schaffner NSG TEST PROCEDURE a. The EUT was placed on the top of a wooden table 0.8 meters above the ground and operated to produce the most unfavorable sequence of voltage changes under normal conditions b. During the flick measurement, the measure time shall include that part of whole operation changes. The observation period for short-term flicker indicator is 10 minutes and the observation period for long-term flicker indicator is 2 hours. TEST SETUP Same as 7.3.3

21 Page 21 of 45 TEST RESULT Flicker Test Summary per EN/IEC (Run time) EUT: RT22 Tested by: Steven Test category: All parameters (European limits) Test Margin: 100 Test date: Start time: 14:01:07 End time: 14:11:29 Test duration (min): 10 Data file name: F cts_data Comment: Normal Operation Customer: HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Test Result: Pass Status: Test Completed Pst i and limit line European Limits Plt and limit line Parameter values recorded during the test: Vrms at the end of test (Volt): Highest dt (%): Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (ms): Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): Test limit (%): 4.00 Pass Highest Pst (10 min. period): Test limit: Pass Highest Plt (2 hr. period): Test limit: Pass

22 Page 22 of ELECTROSTATIC DISCHARGE LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED ESD test ( ) Name of Equipment Manufacturer Model Serial Number Calibration Due ESD Simulator Schaffner NSG Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration VCP units Indirect Support >1m EUT & its direct Support Units HCP Wooden 0.8m Ground Reference Ambient Condition of the Test Site Temperature 22 C EUT AC Voltage Rating AC 230V Humidity 50%RH EUT DC Voltage Rating DC 3.7V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven

23 Page 23 of 45 TEST PROCEDURE Please refer to ETSI EN Clause and EN for the measurement methods. TEST RESULTS The EUT( Handheld two way radio) can function as both transmitter and receiver, so the evaluation of the TT and TR to ESD has undergone by the following means: Two Pieces of EUT are used, one for suffering from ESD and the other one for supporting communication and providing judgments for assessor. Both Operating and Standby mode (Receiving Mode) have been tested Passed and Judged by performance of both TT and TR TT: At the conclusion of each exposure the EUT operates with no user noticeable loss of the communication link and at the conclusion of the total test comprising the series of individual exposures the EUT operates as intended with no loss of user control functions or stored data, as declared by the manufacturer, and the communication link has been maintained during the test. The standby mode is the receiving mode. TR: At the conclusion of each exposure the EUT operates with no user noticeable loss of the communication link. At the conclusion of the total test comprising the series of individual exposures the EUT shall operates as intended with no loss of user control functions or stored data, as declared by the manufacturer, and the communication link has been maintained during the test. Description of the Electrostatic Discharges (ESD) THE RESULT (mode1/mode2/mode3/mode4): Amount of Discharges Voltage Coupling Observation Result (Pass/Fail) Mini 20 / Point ±2KV, ±4kV, ±8kV Air Discharge TR, TT Pass Mini 20 / Point ±2KV, ±4kV Indirect Discharge HCP TR, TT Pass Mini 20 / Point ±2KV, ±4kV Indirect Discharge VCP TR, TT Pass

24 Page 24 of 45 TEST PLOTS: Note: pointes 1,2,3 4,5 and 6 are air discharge.

25 Page 25 of RF ELECTROMAGNETIC FIELD LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED Radiated Electromagnetic Field immunity Measurement ( ) Name of Equipment Manufacturer Model Serial Number Calibration Date Calibration Due Signal Generator R&S SML ANTENNA EMCO 3142C Power Sensor R&S URV5-Z Power Meter R&S NRVD / Power Amplifier KALMUS 7100LC N/A RF Amplifier Milmega AS _ Directional Couple Werlatone C Directional Couple Werlatone C Artificial mouth B&K 4227 N/A Artificial ear B&K 4153 N/A Remark: Each piece of equipment is scheduled for calibration once a year.

26 Page 26 of 45 Test Condition : Sweep Step: 1% Dwell Times: 3 Seconds Modulation: 400 Hz/80% AM Audio Frequency: 1 KHz/60% Test Configuration Ambient Condition of the Test Site Temperature 22 C EUT AC Voltage Rating AC 230V Humidity 50%RH EUT DC Voltage Rating DC 3.7V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven TEST PROCEDURE Please refer to ETSI EN Clause 9.2.2, ETSI EN Clause and EN for the measurement methods. TEST RESULTS During the assessment of CT and CR, the audio quality was monitored by a distortion analyzer located outside the test environment. An audio generator has been used to provide necessary modulation for CT test and for CR evaluation, an RF Generator has been used to provide source. Mode 1/Mode 2/Mode 3/Mode 4: EUT Working Mode Antenna Polarity Frequency (MHz) Field Strength (V/m) Audio Distortion Observation Conclusion Mode1 Mode2 Mode3 Mode4 H/V N/A CT/CR Pass H/V N/A CT/CR Pass H/V % CT Pass H/V % CT Pass H/V % CR Pass H/V % CR Pass H/V N/A CT/CR Pass H/V N/A CT/CR Pass Note: There was not any unintentional transmission discovered in standby mode

27 Page 27 of AC MAINS FAST TRANSIENTS COMMON MODE LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED AC MAINS FAST TRANSIENTS - COMMON MODE (EN ) Name of Equipment Manufacturer Model Serial Number Calibration Date Calibration Due EFT Surge Generator Schaffner Modula INA 6501 STEPTTRANSFORME R Schaffner INA Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION EUT Support Units AC EFT/Burst/ Surge Generator 0.8m Non-Conductive Table Controller To Load Comm. Line 3 m 10cm EUT AC Burst Generator Injection Clamp Non-Conductive Table 0.8m

28 Page 28 of 45 Ambient Condition of the Test Site Temperature 24 C EUT AC Voltage Rating AC 230V/50Hz Humidity 51%RH EUT DC Voltage Rating DC 3.7V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven TEST PROCEDURE Please refer to ETSI EN Clause and EN for the measurement methods. TEST RESULTS Results of Final Tests (MODE 1/MODE 2/ MODE 3/Mode 4) Impulse Frequency: 5 khz Tr/Th: 5/50ns Burst Duration: 15ms Burst Period: 3Hz Test Point Polarity Test Level (kv) Observation Conclusion a.c. port, L +/- 1 TT,TR Pass a.c. port, N +/- 1 TT,TR Pass a.c. port, L-N +/- 1 TT,TR Pass Note: There was not any unintentional transmission discovered in idle mode

29 Page 29 of AC MAINS SURGE LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED AC MAINS SURGES (EN ) Name of Equipment Manufacturer Model Serial Number Calibration Date Calibration Due EFT Surge Generator INA 6501 STEPTTRANSFORMER Schaffner Modula Schaffner INA Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration To AC Source Surge Immunity Test EUT & Support Units 0.8m Controller Computer Ambient Condition of the Test Site Temperature 24 C EUT AC Voltage Rating AC 230V/50Hz Humidity 51%RH EUT DC Voltage Rating DC 3.7V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven

30 Page 30 of 45 TEST PROCEDURE Please refer to ETSI EN Clause and EN for the measurement methods. TEST RESULTS Results of Final Tests (MODE 1/MODE 2/ MODE 3/Mode 4) Voltage Waveform: 1.2/50 us Current Waveform: 8/20 us Polarity: Positive/Negative Phase angle: 0 o, 90 o, 180 o, 270 o Coupling Line Polarity Voltage (kv) Observation Conclusion a.c. power, L-N +/- 1.0 TT,TR Pass Note: There was not any unintentional transmission discovered in idle mode

31 Page 31 of AC MAINS RF COMMON MODE LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED AC MAINS RF COMMON MODE (EN ) Name of Equipment Manufacturer Model Serial Number Calibration Due Signal Generator R&S SML Amplifier AR 75A CDN Schaffner M Audio Analyzer HP 8920B 3104A Artificial mouth B&K 4227 N/A Artificial ear B&K 4153 N/A Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration 10 cm isolation supporter 0.1m< L EUT and Support units CDN Power Amplifier PC Controller Ground Reference Plane Ambient Condition of the Test Site Temperature 25 C EUT AC Voltage Rating AC 230V/50Hz Humidity 52%RH EUT DC Voltage Rating DC 3.7V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven

32 Page 32 of 45 TEST PROCEDURE Please refer to ETSI EN Clause and EN for the measurement methods. TEST RESULTS Results of Final Tests (MODE 1/MODE 2/ MODE 3/Mode 4) Frequency Range: 0.15MHz~80MHz Frequency Step: 1% of fundamental Dwell time: 3 Sec. Audio Frequency: 1 KHz /60% 80% A.M, 400 Hz Sine wave (Voltage: 3 V) Coupling type: CDN / RF Current Probe EUT Working Mode Test Point Frequency (MHz) Field Strength (Vrms) Audio Distortion Observation Conclusion MODE 1 a.c. port N/A CR/CT Pass MODE 2 a.c. port % CT Pass MODE 3 a.c. port % CR Pass MODE 4 a.c. port N/A CR/CT Pass Note: There was not any unintentional transmission in Standby mode

33 Page 33 of VOLTAGE DIPS AND INTERRUPTION LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED VOLTAGE DIPS AND INTERRUPTIONS (EN ) Name of Equipment Manufacturer Model Serial Number Calibration Date Calibration Due EFT Surge Generator INA 6501 STEPTTRANSFORMER Schaffner Modula Schaffner INA Remark: Each piece of equipment is scheduled for calibration once a year. To AC Source Dips/Interruption and Variations Simulator EUT & Support Units 0.8m Controller Computer Test Configuration Ambient Condition of the Test Site Temperature 24 C EUT AC Voltage Rating AC 230V/50Hz Humidity 51%RH EUT DC Voltage Rating DC 3.7V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven TEST PROCEDURE Please refer to ETSI EN Clause and EN for the measurement methods.

34 Page 34 of 45 TEST RESULTS Test conditions Interruption at phase angles of 0, 45, 90, 135, 180, 225, 270 and 315 degree in a 10 sec-interval. Dips / Interruption Reduction (%) Duration (Cycle) Voltage Dips Voltage Dips Voltage Dips Voltage Interruption Note: The duration with a sequence of three dips/interruptions with a minimum interval of 10 s between each test event. Results of Final Tests (MODE 1/MODE 2/MODE 3/Mode 4) Test Mode Voltage dips Voltage Duration Interval Reducti Times (cycle) (Sec) on Observation Conclusion 100% TT,TR Pass 100% TT,TR Pass 30% TT,TR Pass Voltage interruptions 100% TT,TR Pass Note: There was not any unintentional transmission in standby mode

35 Page 35 of 45 APPENDIX 1: PHOTOGRPHS OF TEST SETUP CONDUCTED EMISSION TEST SETUP RADIATED EMISSION TEST SETUP

36 Page 36 of 45 EN VOLTAGE FLUCTUATION/FLICKER TEST SETUP ESD IMMUNITY TEST SETUP Adapter Charger

37 Page 37 of 45 CS IMMUNITY TEST SETUP SRUGE/DIPS/EFT IMMUNITY TEST SETUP

38 RS IMUMUNITY TEST SETUP Report No.: AGC EE01 Page 38 of 45

39 Page 39 of 45 APPENDIX 2: PHOTOGRPHS OF EUT All VIEW OF EUT TOP VIEW OF EUT

40 Page 40 of 45 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

41 Page 41 of 45 BACK VIEW OF EUT LEFT VIEW OF EUT

42 Page 42 of 45 RIGHT VIEW OF EUT OPEN VIEW-1 OF EUT

43 Page 43 of 45 OPEN VIEW-2 OF EUT INTERNAL VIEW-1 OF EUT

44 Page 44 of 45 INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT

45 Page 45 of 45 INTERNAL VIEW-4 OF EUT ---END OF REPORT---