Interference Suppression Film Capacitors MKP Radial Potted Type

Transcription

1 MKP X2 Interference Suppression Film apacitors FEATURES 168x12(halfpage) l P imensions in mm F F " <0.3 mm F = /- 0.1 mm NO FOUS PROUT: USE MKP 339 X2 APPLIATIONS X2 class For X2 electromagnetic interference suppression in across the line applications (50/60 Hz) with a maximum mains voltage of 275 Vac. For application limitations please refer page 14. REFERENE STANARS IE nd edition and EN IE requires pass flamm class B 250 V: UL1414; SA-22.2 No V: SA-22.2 No 8 ENE; Q 305 V: UL1283 MARKING h -value; tolerance; rated voltage; sub-class; manufacturer s type designation; code for dielectric material, manufacturer location; manufacturer s emblem; year and week IELETRI Polypropylene film ELETROES Metallized film lt w Ø dt F' F 10 (1) l 15 h h' H w Ø dt 7.5 to 27.5 mm lead pitch. Supplied in box, taped on ammopack or reel Lead (Pb)-free product RoHS-compliant product PERMISSIBLE VOLTAGE 630 V ENAPSULATION Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0 LIMATI TESTING LASS A. TO EN /110/56/B APAITANE RANGE (E12 SERIES) E12 series to 3.3 µf Preferred values acc. to E6 APAITANE TOLERANE ± 20 %; ± 10 %; ± 5 % LEAS Tinned wire MAXIMUM APPLIATION TEMPERATURE 110 ETAIL SPEIFIATION For more detailed data and test requirements contact: RFI@vishay.com e3 RoHS OMPLIANT ONSTRUTION Mono construction RATE VOLTAGE A 275 V; 50 to 60 Hz For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

2 Interference Suppression Film apacitors MKP X2 OMPOSITION OF ATALOG NUMBER X2 TYPE AN PITHES 7.5 mm 7.5 mm (bent back) 10.0 mm 15.0 mm 22.5 mm 27.5 mm APAITANE (numerically) BF X XX X 2222 ( * ) 338 2X XX X (*) Old ordering code Example: 104 = 10 x 10 = 100 nf MULTIPLIER (nf) TYPE PAKAGING STANAR -TOL PREFERRE TYPES X2 lead length /- 0.5 mm or 3.5 ± 0.3 mm BF loose in box lead length 5.0 ± 1.0 mm BF ± 20 % lead length BF taped Pitch 7.5 mm or bent back to 7.5 mm BF PAKAGING ALTERNATIVE LARGER PITH SIZES -TOL ON REQUEST lead length /- 0.5 mm or 3.5 ± 0.3 mm loose in box lead length 5.0 ± 1.0 mm lead length ± 20 % see tables for details PAKAGING ALTERNATIVE TAPE VERSION (1) ON REQUEST taped H = 18.5 mm; (2) ± 20 % see tables for details PAKAGING ALTERNATIVE -TOL ON REQUEST lead length /- 0.5 mm or 3.5 ± 0.3 mm ± 10 % ± 5 % loose in box lead length 5.0 ± 1.0 mm ± 10 % ± 5 % lead length ± 10 % ± 5 % see tables for details taped pitch 7.5 mm or bent back to 7.5 mm ± 10 % ± 5 % H = 18.5 mm; ± 10 % ± 5 % s 1. Taped on reel pitch = 27.5 mm is not available 2. For detailed tape specifications refer to Packaging information SPEIFI REFERENE ATA FOR THE 275 V A (X2) APAITORS ESRIPTION VALUE Tangent of loss angle: at 1 khz at 10 khz 470 nf nf < 1µF >1µF Rated voltage pulse slope (du/dt) R at 385 V () 100 V/µs R between leads, for 0.33 µf at 100 V; 1 minute > MΩ R between leads, for > 0.33 µf at 100 V; 1 minute > 0 s R between leads and case; 100 V; 1 minute > MΩ Withstanding () voltage (cut off current 10 ma); rise time 100 V/s: 1µF 2 V; 1 min >1µF 1800 V; 1 min Withstanding (A) voltage between leads and case 2050 V; 1 min Maximum application temperature 110 ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

3 MKP X2 Interference Suppression Film apacitors Pitch: 7.5 mm; -tol = ± 20 % (for reference: U Rdc = 630 V) ATALOG NUMBER BF AN PAKAGING AMMOPAK Short leads Long leads H = 18.5 mm /- 0.5 mm 5.0 ± 1.0 mm SPQ Pitch = 7.5 ± 0.4 mm; d t = 0.50 ± 0.05 mm x 10.5 x Pitch: 7.5 mm; -tol = ± 10 % (for reference: U Rdc = 630 V) AMMOPAK H = 18.5 mm Short leads Long leads SPQ /- 0.5 mm 5.0 ± 1.0 mm Pitch = 7.5 ± 0.4 mm; d t = 0.50 ± 0.05 mm x 9.0 x x 10.5 x x 11.5 x For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

4 Interference Suppression Film apacitors MKP X2 Pitch: 7.5 mm; -tol = ± 5 % (for reference: U Rdc = 630 V) AMMOPAK Short leads Long leads H = 18.5 mm /- 0.5 mm (2) 5.0 ± 1.0 mm SPQ Pitch = 7.5 ± 0.4 mm; d t = 0.50 ± 0.05 mm x 9.0 x x 10.5 x x 11.5 x Bent back pitch: 7.5 mm (only taped); -tol = ± 20 % (for reference: U Rdc = 630 V) (g) (2) ATALOG NUMBER BF AN PAKAGING REEL ( mm) (1) H = 16.0 mm; P 0 = 15.0 mm Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 13.0 x x 14.0 x Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 13.0 x x 14.0 x Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 15.5 x x 17.0 x s 1. Reel diameter = 356 mm is available on request 2. Weight for short lead product only SPQ ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

5 MKP X2 Interference Suppression Film apacitors Bent back pitch: 7.5 mm (only taped); -tol = ± 10 % (for reference: U Rdc = 630 V) ATALOG NUMBER BF AN PAKAGING (g) (2) REEL ( mm) (1) H = 16.0 mm; P 0 = 15.0 mm SPQ Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 13.0 x x 14.0 x Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 13.0 x x 14.0 x Bent back pitch = 7.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 15.5 x x 17.0 x s 1. Reel diameter = 356 mm is available on request 2. Weight for short lead product only Bent back pitch: 7.5 mm (only taped); -tol = ± 5 % (for reference: U Rdc = 630 V) (g) (2) REEL ( mm) (1) H = 16.0 mm; P 0 = 15.0 mm SPQ Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 14.0 x Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 13.0 x x 14.0 x Bent back pitch = 7.5 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 15.5 x x 17.0 x s 1. Reel diameter = 356 mm is available on request 2. Weight for short lead product only For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

6 Interference Suppression Film apacitors MKP X2 Pitch: 10.0 mm; -tol = ± 20 % (for reference: U R = 630 V) /- 0.5 mm Pitch = 10.0 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 10.0 x Not available x 11.0 x x 12.0 x AMMOPAK 5.0 ± 1.0 mm SPQ Pitch: 10.0 mm; -tol = ± 10 % (for reference: U R = 630 V) AMMOPAK /- 0.5 mm Pitch = 10.0 ± 0.4 mm; d t = 0.60 ± 0.06 mm ± 1.0 mm SPQ x 10.0 x Not available ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

7 MKP X2 Interference Suppression Film apacitors Pitch: 10.0 mm; -tol = ± 10 % (for reference: U R = 630 V) AMMOPAK /- 0.5 mm 5.0 ± 1.0 mm SPQ x 10.0 x Not available x 11.0 x x 12.0 x Pitch: 10.0 mm; -tol = ± 5 % (for reference: U R = 630 V) AMMOPAK /- 0.5 mm 5.0 ± 1.0 mm SPQ Pitch = 10.0 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 11.0 x x 12.0 x Pitch: 15.0 mm; -tol = ± 20 % (for reference: U R = 630 V) REEL ( mm) 3.5 ± 0.3 mm 5.0 ± 1.0 mm SPQ Pitch = 15 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 11.0 x For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

8 Interference Suppression Film apacitors MKP X2 Pitch: 15.0 mm; -tol = ± 20 % (for reference: U R = 630 V) x 12.0 x Pitch = 15 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 13.5 x x 15.0 x Pitch: 15.0 mm; -tol = ± 10 % (for reference: U R = 630 V) /- 0.3 mm Pitch = 15 ± 0.4 mm; d t = 0.60 ± 0.06 mm 0.01 REEL ( mm) 3.5 ± 0.3 mm 5.0± 1.0mm SPQ REEL ( mm) 5.0 ± 1.0 mm SPQ 25.0± 2.0mm x 11.0 x x 12.0 x Pitch = 15 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 13.5 x x 15.0 x ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

9 MKP X2 Interference Suppression Film apacitors Pitch: 15.0 mm; -tol = ± 5 % (for reference: U R = 630 V) Pitch = 15 ± 0.4 mm; d t = 0.60 ± 0.06 mm x 11.0 x x 12.0 x Pitch = 15 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 13.5 x x 15.0 x /- 0.3 mm Pitch: 22.5 mm; -tol = ± 20 % (for reference: U R = 630 V) 3.5 ± 0.5 mm Pitch = 22.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm 0.12 REEL ( mm) 5.0 ± 1.0mm SPQ REEL ( mm) 5.0 ± 1.0 mm SPQ x 15.5 x x 16.5 x x 18.0 x x 19.5 x Pitch: 22.5 mm; -tol = ± 10 % (for reference: U R = 630 V) 3.5 ± 0.5 mm Pitch = 22.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm REEL ( mm) Short leads Long leads 5.0 ± 1.0 mm SPQ H = 18.5 mm x 15.5 x For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

10 Interference Suppression Film apacitors MKP X2 Pitch: 22.5 mm; -tol = ± 10 % (for reference: U R = 630 V) x 16.5 x x 18.0 x x 19.5 x ± 0.5 mm REEL ( mm) Short leads Pitch: 22.5 mm; -tol = ± 5 % (for reference: U R = 630 V) 3.5 ± 0.5 mm Pitch = 22.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 16.5 x Long leads 5.0 ± 1.0 mm SPQ H = 18.5 mm REEL ( mm) 5.0 ± 1.0 mm SPQ 25.0± 2.0mm x 18.0 x x 19.5 x x 22.0 x Pitch: 27.5 mm; -tol = ± 20 % (for reference: U R = 630 V) 3.5 ± 0.5 mm Short leads Long leads 5.0 ± 1.0 mm SPQ 25.0 ± 2.0mm Pitch = 27.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 19.0 x x 21.0 x x 23.0 x x 25.0 x x 28.0 x SPQ ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

11 MKP X2 Interference Suppression Film apacitors Body length: 31.0 mm Pitch: 27.5 mm -tol = ± 10 % (for reference: U R = 630 V) Pitch = 27.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm Short leads lt = lt = 3.5 ± 0.5 mm (2) 5.0 ± 1.0 mm Long leads SPQ lt = x 21.0 x x 23.0 x x 25.0 x x 28.0 x SPQ Pitch: 27.5 mm; -tol = ± 5 % (for reference: U R = 630 V) Short leads Long leads 3.5 ± 0.5 mm 5.0 ± 1.0 mm SPQ Pitch = 27.5 ± 0.4 mm; d t = 0.80 ± 0.08 mm x 21.0 x x 23.0 x x 25.0 x x 28.0 x SPQ For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

12 Interference Suppression Film apacitors MKP X2 SAFETY APPROVALS X2 VOLTAGE VALUE FILE NUMBERS EN V (A) 1nFto3.3µF FI 6019 UL1414; SA-22.2 No V (A) 1nFto1µF E UL V (A) 1nFto3.3µF E SA-22.2 No V (A) 1nFto3.3µF Q 275 V (A) 1 nf to 3.3 µf Q (F) Q (R) Q (S) The ENE-Approval together with the B-certificate replace all national marks of the following countries (they have already signed the ENE-Agreement): Austria; Belgium; zech. Republic; enmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg; Netherlands; Norway; Portugal; Slovenian; Spain; Sweden; Switzerland; and United Kingdom. 16 Q MOUNTING NORMAL USE The capacitors are designed for mounting on printed -circuit boards.the capacitors packed in bandoliers are designed for mounting in pinted-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to Packaging information. SPEIFI METHO OF MOUNTING TO WITHSTAN VIBRATION AN SHOK In order to withstand vibration and shock tests,it must be insured that the stand-off pips are in good contact with the printed circuit board: For pitches 15 mm capacitors shall be mechanically fixed by the leads For larger pitches the capacitors shall be mounted in the same way and the body clamped. SPAE REQUIREMENTS ON PRINTE IRUIT BOAR The maximum length and width of film capacitors is shown in the figure: Eccentricity as in figure. The maximum eccentricity is smaller than or equal to the product concerned Product heigth with seating plane as given by IE as reference: h max mm or h max h mm. eccentricity l max = l mm STORAGE TEMPERATURE BA116 Storage temperature: T stg = - 25 to + 40 with RH maximum 80 % without condesation HATERISTIS REFERENE ONITIONS b max = b mm Unless otherwise specified, all elctrical values apply to an ambient temperature of 23 ± 1, an atmospheric pressure of 86 to 106 kpa and a relative humidity of 50 ± 2 %. For reference testing, a conditioning period shall be applied over 96 ± 4 hours by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

13 MKP X2 Interference Suppression Film apacitors HARATERISTIS Δ/ 2(%) 4 typical IMPEANE 10 3 Impedance (Ω) 0-2 max nf 1 nf 4.7 nf 10 nf nf 100 nf nf nf TANGET OF LOSS ANGLE 10 3 min Tamb ( ) f (Hz) 10 8 RESONANT FREQUENY 10 2 issipation factor (x 10-4) > 1 µf 220 nf < 1 µf 47 nf < 220 nf 10 nf < 47 nf 10 nf f (MHz) X f (Hz) MAX RMS VOLTAGE AN URRENT AS A FUNTION OF FREQUENY (nf) A voltage (V) A current (ma) 3300 nf nf 470 nf nf 47 nf 10 nf 4.7 nf 1nF Tamb f (Hz) 10 5 Tamb f (Hz) For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

14 Interference Suppression Film apacitors MKP X2 INSULATION RESISTANE 10 6 R (s) Tamb ( ) APPLIATION NOTES For X2 electromagnetic interference suppression in across the line applications (50/60 Hz) with a maximum mains voltage of 275 V (A). These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the A and pulse programs must be used. These capacitors are not intended for series impedance application. For these situations in case safety approvals are requested, please refer to our special capacitors of 1772 series with internal series connection. The maximum ambient temperature must not exceed 110. Rated voltage pulse slope: If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 385 V () and divided by the applied voltage. INSPETION REQUIREMENTS GENERAL NOTES 1. Sub-clause numbers of tests and performance requirements refer to the Sectional Specification, IE_publication EN (IE ) and Section One of this specification. 2. In this table: = destructive N = non-distructive Group inspection requirements SUB-LAUSE NUMBER AN TEST OR N ONITIONS PERFORMANE REQUIREMENTS SUB-GROUP 1A PART OF SAMPLE OF SUB-GROUP imensions (detail) As specified in hapters General data of this specification Initial measurements apacitance Tangent of loss angle: For 1 µf at 10 khz For > 1 µf at 1 khz 4.3 Robustness of terminations Tensile: load 10 N; 10 s Bending: load 5 N; 4 x 90 No visible damage ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

15 MKP X2 Interference Suppression Film apacitors SUB-LAUSE NUMBER AN TEST OR N ONITIONS PERFORMANE REQUIREMENTS 4.4 Resistance to soldering heat No pre-drying Method: 1A Solder bath: 280 uration: 10 s 4.19 omponent solvent Isopropylalcohol at room temperature resistance Method: 2 Immersion time: 5 ± 0.5 min Recovery time: Min 1 hour, max 2 hours Final measurements Visual examination SUB-GROUP 1A PART OF SAMPLE OF SUB-GROUP 1 Initial measurements 4.20 Solvent resistance of the marking: see Section General notes ; item 5. apacitance Tangent of loss angle Insulation resistance apacitance Tangent of loss angle: For 1 µf at 10 khz For > 1 µf at 1 khz Isopropylalcohol at room temperature Method: 1 Rubbing material: cotton wool Immersion time: 5 ± 0.5 min θa = - 55 No visible damage Legible marking Δ/ 5 % of the value measured initially. Increase of tan δ: for: 1 µf or for: > 1 µf ompared to values measured initially As specified in Section Insulation Resistance of this specification No visible damage Legible marking 4.6 Rapid change of temperature θb = cycles uration t = 30 min Inspection Visual examination No visible damage 4.7 Vibration (see note 3.1) Mounting: see Section Mounting of this specification Procedure B4 Frequency range: 10 to 55 Hz. Amplitude: 0.75 mm or Acceleration 98 m/s² (whichever is less severe) Total duration 6 hours Final inspection Visual examination No visible damage 4.9 Shock (see note 3) Mounting: see Section Mounting for more information Pulse shape: half sine Acceleration: 490 m/s² uration of pulse: 11 ms For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

16 Interference Suppression Film apacitors MKP X2 SUB-LAUSE NUMBER AN TEST OR N ONITIONS PERFORMANE REQUIREMENTS Final measurements Visual examination apacitance Tangent of loss angle No visible damage Δ/ 5 % of the value measured initially. Increase of tan δ: for: 1 µf or for: > 1 µf ompared to values measured initially Insulation resistance As specified in Section Insulation Resistance of this specification SUB-GROUP 1 OMBINE SAMPLE OF SPEIMENS OF SUB-GROUPS 1A AN 1B 4.11 limatic sequence Initial measurements apacitance Measured in and Tangent of loss angle: Measured initially in 1A and 1B Temperature: ry heat uration: 16 hours amp heat cyclic Test b First cycle Temperature: old uration: 2 hours amp heat cyclic Test b remaining cycles Visual examination No visible damage Final measurements Legible marking apacitance Δ/ 5 % of the value measured in Tangent of loss angle Increase of tan δ: for: 1 µf or for: > 1 µf ompared to values measured in Voltage proof No permanent breakdown or flash-over 1 V (); 1 min between term. 50 % of values specified in Section Insulation resistance of this specification Insulation resistance SUB GROUP amp heat steady state 56 days; 40 ; 90 to 95 % RH no load Initial measurements apacitance Tangent of loss angle: For 1 µf at 10 khz or For > 1 µf at 1 khz ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

17 MKP X2 Interference Suppression Film apacitors SUB-LAUSE NUMBER AN TEST OR N ONITIONS PERFORMANE REQUIREMENTS Final measurements Visual examination apacitance Tangent of loss angle Voltage proof 1 V (); 1 min between term. Insulation resistance No visible damage Legible marking Δ/ 5 % of the value measured in Increase of tan δ: for: 1 µf or for: > 1 µf ompared to values measured in No permanent breakdown or flash-over 50 % of values specified in Section Insulation resistance of this specification SUB-GROUP Initial measurements apacitance Tangent of loss angle: For 1 µf at 10 khz For > 1 µf at 1 khz 4.13 Impulse voltage 3 successive impulses, full wave, peak voltage: X2: 2.5 kv for 1 µf X2: 2.5 kv/ for > 1 µf Max.24 pulses No selfhealing breakdowns or flashover 4.14 Endurance uration: h 1.25 x U Rac at 110 Once in every hour the voltage is increased to V (RMS) for 0.1 s via resistor of 47 Ω ± 5 % Final measurements Visual examination apacitance Tangent of loss angle Voltage proof 1 V (); 1 min between terminations V (); 1 min between terminations and case. Insulation resistance No visible damage Legible marking Δ/ 10 % compared to values measured in Increase of tan δ: for: 1 µf or for: > 1 µf ompared to values measured in No permanent breakdown or flash-over 50 % of values specified in Section Insulation resistance of this specification For technical questions, contact: rfi@vishay.com ocument Number: Revision: 06-Jul-07

18 Interference Suppression Film apacitors MKP X2 SUB-LAUSE NUMBER AN TEST OR N ONITIONS PERFORMANE REQUIREMENTS SUB-GROUP harge and discharge cycles (50 c/s) charge to UR half sinewave uration: 5 ms ischarge resistance: R = 385 Vdc ( du dt) R min = 2.2 Ω Initial measurements apacitance Tangent of loss angle: For 1 µf at 10 khz For > 1 µf at 1 khz Final measurements apacitance SUB-GROUP Radio frequency characteristic SUB-GROUP Passive flammability lass B Tangent of loss angle Insulation resistance Resonance frequency Bore of gas jet: Ø 0.5 mm Fuel: butane Test duration for actual volume V in mm³: V. 250: 10 s 250 < V. : 20 s < V. 1: 30 s V > 1: 60 s One flame application Δ/ 10 % compared to values measured in Increase of tan δ: for: 1 µf or for: > 1 µf ompared to values measured in % of values specified in Section Insulation resistance of this specification As specified in Section Resonant frequency of this specification. ± 10 % After removing test flame from capacitor, the capacitor must not continue to burn for more than 10 s. No burning particle must drop from the sample. SUB-GROUP Active flammability 20 x 2.5 kv discharges on the test capacitor connected to U Rac The cheese cloth around the capacitors shall not burn with a flame. No electrical measurements are required. ocument Number: For technical questions, contact: rfi@vishay.com Revision: 06-Jul

19 Legal isclaimer Notice Vishay isclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. ustomers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. ocument Number: 9 Revision: 18-Jul-08 1