Customer Interface Unit (CIU)

Transcription

1 Operation and Instruction Manual Customer Interface Unit 1:1:10 16:49:0 Fr1 HPL Electric & Power Pvt. Ltd. Overload Power * 0 # RAILWAY/OC(1P) HPL ELECTRIC & POWER PVT. LTD. 1/1, Asaf Ali Road, New Delhi Phone: , 4811, Fax: hpl@hplindia.com, Website : (Due to continuous development, specification and features are subject to change without prior notice.) BSI R E GI S T E R E D UKAS QUALITY MANAGEMENT 00 ISO-9001:008 HPL Electric & Power Pvt. Ltd.

2 Contents 1. General Information...1. Installation...1. Front View Operation.... Display:... a. Auto Scroll Mode... b. Keypad Mode Vending Code Entry LED indication...8 a. LED Alarm Indication: a. Low Alarm: The buzzer beeps at every 0 minutes when balance is less than 100, excluding Happy Hours i.e. 17:0 to 11:00. b. Overload Alarm: The buzzer beeps when overload occurs i.e. current greater than the load-limit. Over load condition: If load is higher than the load limit, meter will CUT- OFF the load for one minute and raise alarm. If the load is not reduced below load-limit, Meter repeat this for three times automatically and then meter CUT-OFF the load and shall not reconnect it automatically. Now you need to lower the load and press # key for 4 Seconds, to reconnect the load. During overload following indication comes: 1:1:10 Load disconnect 16:49:0 FRI * If Meter is at low credit then it can be MUTE by pressing # key for 4 seconds. b. Overload LED...8 c. Power LED Alarm Indication...9 a. Low Alarm...9 b. Overload Alarm...9 Operation and Instruction Manual Operation and Instruction Manual 9

3 Vending Code Result 1. Not valid code. Old token Typical Screen Shots Not Not Caution This equipment must be keep away from water. The manufacturer shall not be held responsible for failure to comply with the instructions in this manual.. Used token 4. Sequence Error. Successful entry for setting maximum load limit token 6. Successful entry for emergency credit limit token 7. Successful entry for setting of fix charges token 8. Successful entry for tariff token 9. Successful entry for credit token 10. Successful entry for meter rent LL 60 EC Fc Not Not A 1. General information: a. is used to view/access the display parameters and Token entry. b. CIU does not need any external supply or batteries, it is powered up through meter via communication cable. c. CIU is supplied with RS48 connector & cable. d. It can be connected to meter with cable for communication between meter and CIU unit. 11. Successful entry for refund credit amount 7. LED Indication: a. LED: i. When credit LED is in GREEN colour, it shows that credit balance in meter is greater than 100. ii. When credit LED is in RED colour, it shows that credit balance is less than 100. iii. When credit LED is in ORANGE colour, it shows that meter is in debit. b. Over Load LED: When Overload load LED glow, it shows overload occurrence. c. Power LED: When power LED is ON, it shows that CIU power is ON.. Installation: a. Connect the CIU to meter with given RS48 cable. b. Ensure that the cable has been locked with its connector. Meter Connection Diagram CIU RS 48 RS 48 Operation and Instruction Manual 8 Operation and Instruction Manual 1

4 . Front view: b Customer Interface Unit 1:1:10 16:49:0 Fr1 HPL Electric & Power Pvt. Ltd. a c d Note : 1. Meter rent are charges that are applied on per month. This can be changed as applicable by Utility.. Current Tariff is tariff, in which meter is currently running.. Fix charges are the charges, that are applied either monthly or daily basis as decided by Utility. These charges can be changed by Utility. 4. Minimum charges are applied per month. If the consumer consumes electricity equivalent of amount less than the minimum charges then at the end of the billing period the meter will deduct the difference of the minimum amount and the monthly consumption (amount). f Overload Power e 6. Vending Code Entry: To enter the 1 digits Numeric Vending Code in the meter, follow below steps: * i. Press key for 4 seconds then it will show display. i.e. insert Token No.1. a. LCD b. Overload LED c. LED d. Power LED e. Buzzer f. Numeric Keypad 4. Operation: As soon as the CIU is connected to meter, it is powered up and performs the LCD segment check then goes to Auto Scroll Mode display. ii. After entering 9 digits it shows display as below iii. Enter full 1 digit Vending Code. Then it shows display as below Number of digits entered. ok 1 This number shows no. of digit entered. Please check OK before entering Token. iv. Press # key to accept the Token. v. Display will show the following results : Note : In token entry mode, if you entered any wrong entry, please press * entry, this is equivalent to backspace. to clear wrong. Display: There are two modes of display. A. Auto Scroll Mode B. Keypad Mode Operation and Instruction Manual Operation and Instruction Manual 7

5 Note : ABC is 1 digit code shown in typical screen one after another automatically as shown. This code generated by meter automatically at end of every month. This code is used by Utility to get information about meter i.e. 1. Meter Serial Number. Balance Amount. reading of meter 6. Cover Open Status. ABC generation date 7. ABC Upload 4. Tamper statusof meter 7. kw Maximum Demand in kw 8. MD 7 8:10:10 9:0 MD Maximum Demand & Note : Screen number 7 & 8 can be shown one after another automatically by pressing key Cumulative Balance Amount 0.00 Meter Rent 0.00 Fc Previous day Consumed Amount Current Tariff Fix Charges (Monthly) 44. Minimum Charges Number of Transaction Accepted (ACPT) by meter Number of Transaction Rejected 6 (RJtD) by meter Total Cumulative Amount Vended in meter 1:1:10 16:49 Real & with weekday. Meter Serial Number to which CIU is connected A. Auto Scroll Mode: Typical screenshots shows as given below, when CIU is connected to meter Current load and the cost of that load sl6 kw Cumulative Energy in with Slab No. & Balance Amount Note: The parameter in Auto Scroll Mode will automatically scroll one by one at every 10 sec. interval. B. Keypad Mode : The parameters in this mode can be viewed by pressing numeric keys given at CIU front :1: :01:11 1:8 9. 0: Last Retained Code Part-1 (RET) Last Retained Code Part- (RET) Last Retained Code Part- (RET) Last Retained Code & time Last Retained Code Amount nd Last Retained Code Part-1 (RET) nd Last Retained Code Part- (RET) nd Last Retained Code Part- (RET) nd Last Retained Code & time nd Last Retained Code Amount rd Last Retained Code Part-1 (RET) rd Last Retained Code Part- (RET) Operation and Instruction Manual 6 Operation and Instruction Manual

6 :11:10 10: :08: : :06:11 1: rd Last Retained Code Part- (RET) rd Last Retained Code & time rd Last Retained Code Amount 4th Last Retained Code Part-1 (RET) 4th Last Retained Code Part- (RET) 4th Last Retained Code Part- (RET) 4th Last Retained Code & time 4th Last Retained Code Amount th Last Retained Code Part-1 (RET) th Last Retained Code Part- (RET) th Last Retained Code Part- (RET) th Last Retained Code & time th Last Retained Code Amount Note: 1. Retained Code (RET) is the Tokens entered. This code is shown in typical screens, one after another automatically, after pressing key 1 on numeric keypad as shown here.. Retained credit code & time is the date & time when Token was entered. 6. Day Left (based on consumption of last seven days) Note: Days left : This shows that how many days you can run the load, without recharging the meter (based on consumption of last seven days). Meter is programmed for based tariff structure. Tariff Structure Tariff - 1 Tariff - Tariff - Tariff Screen number 7 to 0 shall be shown one after another automatically by pressing key. Note : In above screen the Tariff structure is as follows : Slab No. Start End () above 4.90 Tariff 1 : This shows the end of 1st slab of your Tariff in and rate applied for this tariff as shown in table. First Slab start from 0. Tariff : This shows the end of nd slab of Tariff in with rate applied and it start from 1st slab tariff ending. Tariff : This shows that end of rd slab of Tariff in with rate applied and it start from nd slab tariff ending. Tariff 4 : This shows that end of 4th slab of Tariff in with rate applied and it start from rd slab tariff ending kw Current load and the cost of that load Authenticated Billing Code Part Authenticated Billing Code Part- Authenticated Billing Code Part Total Cumulative Amount Vended in meter Operation and Instruction Manual 4 Operation and Instruction Manual