PAN-WAY T-70 AND TWIN-70 NON-METALLIC PERIMETER TRUNKING

Transcription

1 PAN-WAY T-70 AND TWIN-70 NON-METALLIC PERIMETER TRUNKING T-70 Trunking with WORKSTATION OUTLET CENTER Offset Box Twin-70 Trunking PANDUIT NETWORK CONNECTIVITY GROUP Cable Routing Solutions. T-70 and Twin-70 multi-channel trunking provide solutions for routing low voltage, fibre optic and/ or power cabling along fixed perimeter walls. The T-70 and Twin-70 trunking systems consist of trunking base and cover, fittings and termination hardware. T-70 and Twin-70 trunking can mount NEMA standard screw-on faceplates or superior PAN-WAY Snap-On Faceplates directly to the channel. T-70 trunking can also terminate in an offset configuration using the T-70 WORKSTATION OUTLET CENTER Offset Box. T-70 Trunking: Multi-channel two-piece design for power, low voltage and fibre optic applications; Fittings maintain 25mm bend radius control for high performance copper and fibre optic cabling; Extremely tamper resistant latch design excellent for school and university applications; Fittings available to transition to Twin-70 and T-45 trunking. Twin-70 Trunking: Multi-channel three-piece design for power, low voltage and fibre optic applications; Two totally independent channels maintained throughout the system for independent access to power and low voltage, fibre optic cabling; Fittings maintain 25mm bend radius control for high performance copper and fibre optic cabling; Extremely tamper resistant latch design excellent for school and university applications; Fittings available to transition to T-70 and T-45 trunking. Sold exclusively through authorized PANDUIT distributors. 133 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

2 PAN-WAY T-70 Perimeter Trunking Base & Cover PAN-WAY Type T-70 Perimeter Trunking is an aesthetically designed, multi-channel system to route, protect and conceal data, voice, video, fibre-optic and power cabling. T-70 System Benefits: Fittings maintain the TIA/EIA required 25mm bend radius for Fibre-Optic and Category 5 cabling systems Supplied with pre-punched mounting holes Tamper resistant Compatible with: PAN-WAY Snap-On Faceplates Any U.S. Standard Screw-On Electrical/Communication Faceplate(s) 45 x 45 Electrical/Communication Faceplate(s) T70B T70C A=3323mm mm Number T-70 Trunking Base 2m lengths Number Colours 3m lengths T70BAW2 20m T70BAW3 18m T-70 trunking base in 2 or 3m lengths. Supplied with pre-punched mounting 45mm holes every 203mm. T-70 Trunking Cover T70CAW2 40m T70CAW3 36m T-70 trunking cover in 2 or 3m lengths. T-70 Trunking Divider Wall T70DW2 40m T70DW3 Grey 36m ONLY Snaps onto rails in trunking base to create separate channels. Must use with wire retainers to ensure channel separation per UL/CSA. T70DW 19mm 36mm NOTE: Order trunking base and cover separately. All parts listed in AW ( ) colour. To order other colours substitute IW (international ) and WH (). Order number of meters required, in multiples of Standard Carton Quantity. T70BC**-X T70IC T70RA T70T Type T-70 Fittings T70CC**-X T70OC T70EC T70TDT T70TDC T70TDB Number Description Colours T70BCAW-X Base Coupler Fitting T70CCAW-X Cover Coupler Fitting T70ICAW Inside Corner Fitting T70OCAW Outside Corner Fitting T70RAAW Right Angle Fitting T70ECAW End Cap Fitting Conduit breakouts: 12mm T70TAW Tee Fitting T70TDT: (Top Position) T70TDC: (Center Position) T70TDB: (Bottom Position) T-70 Trunking Divider Inserts (Power & Data Applications). Separate power and data within Tee Fitting when divider wall placed in top, center or bottom position Grey ONLY All parts listed in AW ( ) colour. To order other colours substitute IW (international ), IG (International Grey), and WH (). Order number of pieces required, in multiples of Standard Package Quantity pcs pc 10 Maintains TIA/EIA 568-A and 569-A minimum 25mm cable bend radius 134 Prime Items appear in BOLD. CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

3 PAN-WAY PERIMETER TRUNKING SYSTEM Type T-70 Fittings (Continued) T70EE T70TR T70TRC T70TRI Number Description Colours T70EEAW T70TRAW Entrance End Fitting. Conduit breakouts: 12mm, 19mm, 25mm, 32mm". Entry from ceiling or wall. Transition Fitting to any LD Profile Trunking. Includes fitting for bend radius control. Maintains channel separation within T-70 trunking Base & Cover T70TRCAW Transition Fitting to any LD Profile Trunking Cover Only T70TRI Divided insert for T70 to LD2P10. Maintains channel separation within T70TR Fitting All parts listed in AW ( ) colour. To order other colours substitute IW (international ), IG (International Grey), and WH (). T-70 Trunking Accessories available on page 139 Order number of pieces required, in multiples of Standard Package Quantity. Grey ONLY Maintains TIA/EIA 568-A and 569-A minimum 25mm cable bend radius Tee Insert Configurations KEY Data Cabling Power Cabling Tee Insert Divider Wall T70TDT T70TDC T70TDB Divided Tee Inserts are used to separate power and data cabling for various tee configurations. Maintains 25mm bend radius of data cables. For Technical Assistance, refer to inside back cover for your local PANDUIT Sales Office. 135 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

4 WORKSTATION OUTLET CENTER Offset Box for T-70 Trunking T70WC T70WC2 T70WCU T70WCD Number Description Colours WORKSTATION OUTLET CENTER Offset Box For Screw-On Faceplates T70WCAW Two-piece box & bracket accept any NEMA standard faceplate. All parts listed in AW ( ) colour. To order other colours substitute IW (international ), IG (International Grey), and WH (). Order number of pieces required, in multiples of Standard Package Quantity. WORKSTATION OUTLET CENTER Offset Box For PAN-WAY Snap-On Faceplates T70WC2AW Two-piece box & bracket accept any standard electrical outlet. Accepts any PAN-WAY Snap-On Electrical/ Communication Faceplates. WORKSTATION OUTLET CENTER Offset Box For European Screw-On Faceplates T70WCUAW Two-piece box and bracket. Power box accepts twogang 86mm British Standard power devices. Communication bracket accepts PANDUIT TG80FH4 snap-on faceplate. WORKSTATION OUTLET CENTER Offset Box For European Screw-On Faceplates T70WCDAW Two-piece box and bracket. Power box accepts twogang 80mm faceplate with outlet mounting hole widths of 60.3mm. Communication bracket accepts PANDUIT TG80FH4 snap-on faceplate. WORKSTATION OUTLET CENTER Offset Box For PAN-WAY Snap-On Bezels & Faceplates T70WCF2AW Two-piece box & bracket accepts 2 gang PAN-WAY 45X45 Module Snap-On Faceplate and any PAN-WAY Classic Series Communication Snap-On Faceplate. T70WCF2 The WORKSTATION OUTLET CENTER offset box places electrical and communications devices into a common area while maximizing the cabling capacity of the trunking channel. The WORKSTATION OUTLET CENTER offset box Snap-On Faceplate version provides the lowest installed cost by reducing hardware and labour. 136 Prime Items appear in BOLD. CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

5 PAN-WAY PERIMETER TRUNKING SYSTEM PAN- WAY Twin-70 Perimeter Trunking Base & Cover PAN-WAY Type Twin-70 Perimeter Trunking is an aesthetically designed system featuring two separate dedicated channels, to route, protect and conceal data, voice, video, fibre-optic and power cabling. Twin-70 System Benefits: Separate channels allow independent access to power and communication cabling throughout the entire system Fittings maintain the TIA/EIA required 25mm bend radius for Fibre-Optic and Category 5 cabling systems Tamper resistant Supplied with pre-punched mounting holes Compatible with: PAN-WAY Snap-On Faceplates Any U.S. Standard Screw-On Electrical/Communication Faceplate(s) 45 x 45 Electrical/Communication Faceplate(s) T702B A=2961mm 2 A=2961mm 2 184mm 45mm Number Twin-70 Trunking Base 2m lengths Number Colours 3m lengths T702BAW2 8m T702BAW3 9m Twin-70 trunking base in 2 or 3m lengths. Supplied with pre-punched mounting holes every 203mm. T-70 Trunking Cover T70CAW2 40m T70CAW3 36m T-70 or Twin-70 trunking tamper resistant cover in 2 or 3m lengths. NOTE: 4m of cover needed for every 2m of base. T-70 Trunking Divider Wall T70DW2 40m T70DW3 Grey 36m ONLY Snaps onto rails in trunking base to create separate channels. Must use with wire retainers to ensure channel separation per UL/CSA. T70C 36mm All parts listed in AW ( ) colour. To order other colours substitute IW (international ) and WH (). NOTE: Order trunking base and cover separately. Order number of meters required, in multiples of Standard Carton Quantity. T70DW 19mm For Technical Assistance, refer to inside back cover for your local PANDUIT Sales Office. 137 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

6 Type Twin-70 Fittings T702BC**-X T702IC T702RA T702TRL T70CC**-X T702OC T702TR T702TRI Number Description Colours T702BCAW-X Base Coupler Fitting T70CCAW-X Cover Coupler Fitting T702ICAW Inside Corner Fitting T702OCAW Outside Corner Fitting T702RAAW Right Angle Fitting T702TRAW Transition Fitting To T-70 Trunking T702TRLAW T702TRI Transition Fitting To any LD Profile Trunking Divided Insert for T702 to T70 or T702 to LD profile. Maintains channel separation within T702TR or T702TRL fitting. T702TAW Tee Fitting T702EEAW T702ECAW Entrance End Fitting Conduit breakouts: 12mm,19mm, 25mm, 32mm Entry from ceiling or wall. End Cap Fitting Conduit breakouts: 12mm pc. 5 1 pc. 5 Grey 1 pc. 5 1 pc. 5 1 pc. 5 All parts listed in AW ( ) colour. To order other colours substitute IW (international ), IG (International Grey), and WH (). Order number of pieces required, in multiples of Standard Package Quantity. Maintains TIA/EIA 568-A and 569-A minimum 25mm cable bend radius T702T T702EE T702EC Faceplate Mounting Frame for 80mm German Screw-On Faceplates T702CPAW Number Description Colour Order number of pieces required, in multiples of Standard Package. NOTE: Can only be used with Twin-70 base. Contact PANDUIT for availability. Faceplate Mounting Frame for 80mm German Screw-On Faceplates T702CPAW Two-Piece bracket. Power bracket accepts two-gang 80mm faceplate with outlet mounting holes widths of 60.3mm. Communication bracket acepts PANDUIT TG80FH4 snap-on faceplate. 138 Prime Items appear in BOLD. CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

7 PAN-WAY PERIMETER TRUNKING SYSTEM Type T-70 & Twin-70 Trunking Accessories T70DB-X T70S-X T70WR-X T70SDB-X Number Description Colour Device Mounting Bracket T70DB-X Wire Retainer T70WR-X Used to mount NEMA standard single gang electrical outlets and communication devices with either screw-on or snap-on single gang faceplates. Holds wires in place. Will not interfere with cover installation. Surface Mount Box Spacer Plate T70S-X Spacer plate is used to mount a CBX4 Surface Mount Box onto the Device Bracket or Hanging Box shown above. Standard Faceplate Bracket T70SDB-X Used to mount NEMA standard single gang screw-on electrical/communication faceplates (not for use with snap-on faceplates). Order number of pieces required, in multiples of Standard Package Quantity. Grey Grey Grey ONLY 1 pc. 10 Using the spacer plate a CBX4 box can be mounted onto Twin-70 or T-70 trunking. (See PAN-NET Section) The CBX4 box features a fibre spool for managing fibre optic cable slack. T-70 Snap-On Fibre Spool Bracket NEW! T70FSB Brackets are adjustable for slack length Maintains TIA/EIA 568-A and 569-A minimum 25mm cable bend radius Number Description Colour T-70 Snap-On Fibre Spool Bracket T70FSB Fibre spool bracket that snaps onto base of T-70. Provides method to contain 1m or more of fibre slack and provides strain relief. Maintains 25mm bend radius for fibre optic Grey cabling. Bracket distance can be adjusted to fit the length of slack required. Order number of pieces required, in multiples of Standard Package. NOTE: Can be used with T-70 and Twin-70 base. Contact PANDUIT for availability Use the T70FSB with T-70 trunking to contain 1m or more of fibre slack and maintain a 25mm cable bend radius. For Technical Assistance, refer to inside back cover for your local PANDUIT Sales Office. 139 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

8 Quick Wire Fill Capacities for T-70 Perimeter Trunking This information is to be used as a guide in selecting the proper size trunking. The maximum amounts may vary according to the wire installation methods, straightness of wires, etc. A= 3323mm 2 Wirefill #1: T-70 Trunking with no devices a b A= 555mm 2 A= 1110mm 2 Wirefill #2: Power & Data using Three Sided Hanging Box and Device Bracket A= 2368mm 2 Wirefill #3: Data Only using Vertical Sloped Screw-On Communication Faceplates A= 3039mm 2 Wirefill #4: Data Only usiing Horizontal Sloped Snap-On Communication Faceplates a b A=587mm 2 A= 2013mm 2 Wirefill #5: Power & Data using the WORKSTATION OUTLET CENTER Offset Box 140 Prime Items appear in BOLD. CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

9 PAN-WAY PERIMETER TRUNKING SYSTEM Quick Wire Fill Capacities for T-70 Perimeter Trunking (Continued) This information is to be used as a guide in selecting the proper size perimeter trunking. The maximum amounts may vary according to the wire installation methods, straightness of wires, etc. Trunking Channel Configurations Area (mm 2 ) CABLE DIAMETER (mm) Wirefill #1: T70 with No Devices Wirefill #2: Power & Data using the Hanging Box & Device Bracket Wirefill #3: Data Only using Screw-On Faceplates Wirefill #4: Data Only using Snap-On Bezels Wirefill #5: Power & Data using the WORKSTATION OUTLET CENTER Offset Box Trunking Channel Configurations Area (mm 2 ) CABLE DIAMETER (mm) Wirefill #1: T70 with No Devices Wirefill #2: Power & Data using the Hanging Box & Device Bracket Wirefill #3: Data Only using Screw-On Faceplates Wirefill #4: Data Only using Snap-On Bezels Wirefill #5: Power & Data using the WORKSTATION OUTLET CENTER Offset Box For Technical Assistance, refer to inside back cover for your local PANDUIT Sales Office. 141 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

10 Quick Wire Fill Capacities for Twin-70 Trunking This information is to be used as a guide in selecting the proper size trunking. The maximum amounts may vary according to the wire installation methods, straightness of wires, etc. a b A= 1323mm 2 Wirefill #1: Power & Data with No Terminations A= 923mm 2 A= 2961mm 2 Wirefill #2: One Twin-70 Channel with No Devices A= 2006mm 2 A= 2142mm 2 Wirefill #3: Data Only using Vertical Sloped Screw-On Communication Faceplates Wirefill #4: Power using Device Bracket & U.S. Standard Screw-On Faceplates A= 2671mm 2 A= 1503mm 2 Wirefill #5: Data Only using Horizontal Sloped Snap-On Communication Faceplates Wirefill #6: 20A TVSS Rectangular Outlet using Device Bracket & Snap-On Electrical/ Communication Faceplate 142 Prime Items appear in BOLD. CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

11 PAN-WAY PERIMETER TRUNKING SYSTEM Quick Wire Fill Capacities for Twin-70 Perimeter Trunking (Continued) This information is to be used as a guide in selecting the proper size perimeter trunking. The maximum amounts may vary according to the wire installation methods, straightness of wires, etc. Trunking Channel Configurations Wirefill #1: Power & Data No Terminations Wirefill #2: One Twin-70 Channel with No Devices Wirefill #3: Data Only using Device Bracket & Screw-On Faceplates Wirefill #4: Power using Device Bracket & Screw-On Faceplates Wirefill #5: Data Only using Snap-On Bezels Wirefill #6: TVSS Power Device using Device Bracket & Snap-On Faceplate Area (mm 2 ) CABLE DIAMETER (mm) Trunking Channel Configurations Wirefill #1: Power & Data No Terminations Wirefill #2: One Twin-70 Channel with No Devices Wirefill #3: Data Only using Device Bracket & Screw-On Faceplates Wirefill #4: Power using Device Bracket & Screw-On Faceplates Wirefill #5: Data Only using Snap-On Bezels Wirefill #6: TVSS Power Device using Device Bracket & Snap-On Faceplate Area (mm 2 ) CABLE DIAMETER (mm) For Technical Assistance, refer to inside back cover for your local PANDUIT Sales Office. 143 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01

12 NOTES 144 CYAN MAGENTA YELLOW BLACK Seite: Datum: 8/8/01