R&S TS-PSAM Analog Source and Measurement Module Scanning multimeter and data acquisition unit

Size: px

Start display at page:

Download "R&S TS-PSAM Analog Source and Measurement Module Scanning multimeter and data acquisition unit"

Lucas Lee
6 years ago
Views:

1 TS-PSAM_bro_en_ indd 1 Product Brochure Test & Measurement R&S TS-PSAM Analog Source and Measurement Module Scanning multimeter and data acquisition unit :34:44

2 R&S TS-PSAM Analog Source and Measurement Module At a glance Key facts The R&S TS-PSAM analog source and measurement module is a CompactPCI/PXI module which takes up only one slot in the R&S CompactTSVP test system versatile platform. The module contains a floating measurement unit, a program mable source and a discharge circuit. The components can be switched to the ana log bus of the R&S CompactTSVP by means of relays. The trigger logic of the measurement unit is linked to the PXI trig ger lines of the backplane. Two trigger inputs and outputs are provided on the front-panel connector. Two level-programmable triggers can additionally be derived from the analog input signal. The scanning of multiple channels is already provided on board by two 4:1 relay multiplexers. Floating measurement unit DC measurement ranges from 10 mv to 125 V, 1 µa to 1 A AC RMS measurement ranges from 20 mv to 90 V, 100 µa to 1 A Resistance measurement ranges from 1 Ω to 10 MΩ, 2-wire and 4-wire Measurement synchronization via PXI clock and trigger 16-bit A/D converter, max. sampling rate 200 ksample/s, on-board memory Floating DC source Adjustable voltage and current limits, ±5 V, 100 ma Four-quadrant operation Fast settling time Sense lines Discharge circuit Up to 125 V discharge voltage Discharge current 400 ma max. Analog measurement bus access to eight bus lines LabWindows/CVI device driver support GTSL test software library in DLL format EGTSL test software library for in-cir cuit test Functional block diagram of the R&S TS PSAM LABD2 ABD2 LABD1 ABD1 LABC2 ABC2 LABC1 ABC1 LABB2 ABB2 LABB1 ABB1 LABA2 ABA2 LABA1 ABA1 IL1, IL2 Coupling Relais Analog bus (AB) DCS_HI DCS_SHI DCS_SLO DCS_LO IL1, IL2 Local analog bus (LABA1 to LABD2, GND) RACOM RBCOM XTO1, XTO2 XTI1, XTI2 AUX1, AUX2 CHA-GND RACH1 to RACH4 RBCH1 to RBCH4 DCS Voltage and current source MU_HI MU MU_SHI Voltage and MU_SLO current meamu_lo surement unit MU_HI DCH MU_LO Discharge unit GND PXI_TRIG0 to PXI_TRIG7 AUX1, AUX2 Isolation XTA1, XTA2 Trigger 2 TS-PSAM_bro_en_ indd :34:44

Typical applications The module is used for general measurement tasks such as a digital multimeter, for the in-circuit test (ICT) and the R&S Com pacttsvp selftest.

For the ICT, the following measurement tasks are performed by the R&S TS PSAM: Discharge of capacitors Contact test Continuity test Short-circuit test 2-wire and 4-wire resistance mea surements (DC)

3 Typical applications The module is used for general measurement tasks such as a digital multimeter, for the in-circuit test (ICT) and the R&S Com pacttsvp selftest. As part of a functional test, the module can be used for voltage, current and resistance measurements. In data acquisition mode, the module can capture waveforms with up to 200 ksample per second. For the ICT, the following measurement tasks are performed by the R&S TS PSAM: Discharge of capacitors Contact test Continuity test Short-circuit test 2-wire and 4-wire resistance mea surements (DC) If necessary, the source and the measurement unit can be taken to ground or can be used independently of each other. The power supply for floating instrument functionalities such as measurement unit and DC source is provided via an associated rear I/O module (R&S TS-PDC), which is included in the delivery. When used together with the R&S TS PICT module, guarded impedance measurements can also be performed: Resistor, capacitor and inductance 3- and 6-wire impedance tests Diode and transistor test The DUT signals are connected from the R&S TS-PMB matrix module to the R&S TS-PSAM source and measurement module via the ana log measurement bus. The careful approach to hand ling analog signals leads to the interconnection solu tion of the R&S CompactTSVP analog bus. The 8-line analog bus is located directly above the front-connector area where space is provided for onboard signal conditioning and signal routing by coupling relays. A large number of DUT signals can be routed to the R&S TS PSAM via the switching modules and the analog measurement bus. Software support A LabWindows/CVI DMM driver according to the IVI standard is available for the multimeter functions of the mod ule. All other functional groups of the hardware are served via specific driver extensions. Function panels and online help are available as common features for the LabWindows/CVI driver. The ICT is performed with a dedicated soft ware package named EGTSL (Enhanced Generic Test Software Library). Security by selftest and diag nostic features The built-in selftest capability of the mod ule ranges from fast diagnostics to the com plete, automated evaluation of all relays and switching paths. Diagnostic LEDs on the front panel speed up system integration and allow proper operation to be determined at a glance. In the R&S CompactTSVP selftest, the R&S TS-PSAM is used as the measurement unit to test other modules and components in the chassis. Rohde & Schwarz R&S TS-PSAM Analog Source and Measurement Module 3 TS-PSAM_bro_en_ indd 3

4 Specifications Application in R&S TSVP platform R&S CompactTSVP 1 slot required Interface Control bus CompactPCI/PXI DUT connector (front) DIN 41612, 96 pins Rear I/O connector CompactPCI, 110 pins Tolerances and specified values apply under the following conditions: Period 1 year Temperature range +23 C ±5 C Additional error due to temperature coefficient ±(0.1 uncertainty)/ C for a valid autocorrection period and in ambient temperature ranges from +5 C to +18 C and +28 C to +40 C DC voltage source (DCS) Floating source working voltage Output voltage 125 V max. 5 V to +5 V Resolution 200 μv typ. Accuracy mv Maximum output current 100 ma Source impedance see current limiting Current limiting range Resolution Accuracy Output characteristic (sense lines not connected) 100 μa 2 na μa max. 10 kω 1 ma 20 na μa max. 1 kω 10 ma 200 na μa max. 100 Ω 100 ma 2 μa μa 10 Ω Accuracy: ±(% of set value + absolute value). Temperature coefficient: ±(0.2 accuracy)/ C. Floating measurement unit working voltage Waveform sampling rate 125 V max. 200 ksample/s max. Memory 8 ksample Voltage range Resolution Input characteristics Accuracy, averaging, 2) Accuracy, no averaging, 3) 10 mv 4) 0.4 μv μv μv 20 mv 4) 0.8 μv μv μv 50 mv 4) 2 μv μv μv 100 mv 4 μv μv μv 200 mv 8 μv μv μv 500 mv 20 μv μv μv 1V 40 μv μv μv 2V 80 μv μv μv 5V 0.2 mv mv mv 10 V 0.4 mv mv mv 20 V 0.8 mv 10 MΩ mv mv 50 V 2 mv 10 MΩ mv mv 100 V 4 mv 10 MΩ mv mv 200 V 5) 8 mv 10 MΩ mv mv 2) 3) 4) 5) Accuracy: ±(% of reading + absolute value).temperature coefficient: ±(0.1 accuracy)/ C. Average 100 sample, measuring time 20 ms, filter 400 Hz. Waveform recording 1 ksample to 8 ksample, no averaging, filter 40 khz. Measurement Low GND-referenced. Input signal 125 V max. 4 TS-PSAM_bro_en_ indd 4

5 Current range Resolution Accuracy, averaging 3), 4) Accuracy, no averaging 3), 5) 1 μa 2 μa 5 μa 10 μa 20 μa 50 μa 100 μa 200 μa 500 μa 1 ma 2 ma 5 ma 10 ma 20 ma 50 ma 100 ma 200 ma 2) 500 ma 2) 1 A 2) 0.04 na 0.08 na 0.2 na 0.4 na 0.8nA 2 na 4 na 8 na 20 na 40 na 80 na 0.2 μa 0.4 μa 0.8 μa 2 μa 4 μa 8 μa 20 μa 40 μa na na na na na na na na na na na μa μa μa μa μa μa μa μa na na na na na na na na na na na μa μa μa μa μa μa μa μa 2) 3) 4) 5) Input characteristics: Active current measurement via current/voltage amplifier. Input characteristics: 0.5 Ω shunt. Accuracy: ±(% of set value + absolute value). Temperature coefficient: ±(0.2 accuracy)/ C. Average 100 samples, measuring time 20 ms, filter 400 Hz. Waveform recording 1 ksample to 8 ksample, no averaging, filter 40 khz. RMS measurements The specified accuracy only applies to sinewave signals in the frequency range from 20 Hz to 50 khz. The accuracy is attained only if the input level amounts to at least 10 % of full scale deflection. AC voltage (RMS) Range Frequency range 20 mv 50 mv 100 mv 200 mv 500 mv 1V Accuracy μv μv μv μv μv μv μv μv μv μv μv μv μv μv μv μv μv μv μv μv mv mv mv mv Rohde & Schwarz R&S TS-PSAM Analog Source and Measurement Module 5 TS-PSAM_bro_en_ indd 5

6 Range 2V 5V 10 V 20 V 50 V 100 V 2) Frequency range Accuracy mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv mv Accuracy: ±(% of reading + absolute value). Temperature coefficient: ±(0.1 accuracy)/ C. Average 100 sample, measuring time 20 ms, filter 40 khz. AC input signal max. 90 V RMS. 2) AC current (RMS) Range 100 μa 200 μa 500 μa 1 ma 2 ma 5 ma 10 ma Frequency range Accuracy na na na na μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa μa 6 TS-PSAM_bro_en_ indd 6

7 Range 20 ma Frequency range 50 ma 100 ma 200 ma 500 ma 1A Accuracy μa μa μa μa μa μa μa μa μa μa μa μa ma ma ma ma ma ma ma ma ma ma ma ma Accuracy: ±(% of reading + absolute value). Temperature coefficient: ±(0.1 accuracy)/ C. Average 100 sample, measuring time 20 ms, function AC. Resistance measurement Resistance measurements are performed with the DC voltage source and the measurement unit. Two-wire and four-wire measurements can be performed. Depending on the range, two different methods are used. Source voltage Source current Range Accuracy Mode 3) 2) CS 0.5 V max. 100 ma 0.1 Ω to 1 Ω mω CS 0.2 V max. 10 ma 1 Ω to 10 Ω 0.5 VS 0.2 V 25 ma max. 10 Ω to 100 Ω 0.5 VS 0.2 V 2.5 ma max. 100 Ω to 1 kω 0.5 2) 3) 1 kω to 10 kω 10 kω to 100 kω V V 0.2 V 0.2 V 1 ma max. 0.1 ma max. 100 kω to 1 MΩ 1 MΩ to 10 MΩ 1 1 V V 1V 5V 0.1 ma max. 0.1 ma max. Accuracy: ±% of reading. Temperature coefficient: ±(0.1 accuracy)/ C. Accuracy: ±(% of reading + absolute value). Temperature coefficient: ±(0.1 accuracy)/ C. CS: 4-wire, current injection, voltage measurement. V: 2-wire, voltage injection, current measurement. VS: 4-wire, voltage injection, current measurement. Discharge unit (DCH) Input voltage 125 V max. Overvoltage protection 200 V DC max. Max. discharge current 400 ma typ. Synchronization Trigger units 4 logical blocks Trigger inputs per unit Pattern per unit 8 x PXI; 2 x front connector (TTL); 2 x analog input signal 12 bit, 3 states (high, low, don t care) Slope per unit programmable Rohde & Schwarz R&S TS-PSAM Analog Source and Measurement Module 7 TS-PSAM_bro_en_ indd 7

8 Discharge unit (DCH) Delay per unit 50 ns to 100 s Trigger outputs 8 x PXI; 2 x front connector (TTL) Analog measurement bus and relay multiplexer Analog measurement bus access 8 busses Relay scanner 2 x 4-to-1 multiplexer Max. voltage DC/AC 125 V/125 V (RMS) Max. current 1 A/1 A (RMS) Max. switching power 10 W/10 VA General data Power consumption +5 V/5.8 A, +3.3 V/0.2 A, 30 W max. incl. R&S TS-PDC Environmental conditions Temperature operating temperature range +5 C to +40 C storage temperature range 10 C to +60 C +40 C, 80 % rel. humidity, steady state in line with EN Damp heat Mechanical resistance Vibration sinusoidal 5 Hz to 55 Hz, 0.15 mm amplitude const., 55 Hz to 150 Hz, 0.5 g const., in line with EN Hz to 300 Hz, acceleration 1.2 g (RMS), in line with EN g shock spectrum, in line with MIL-STD-810E, method 516.4, procedure I random Shock Product conformity Electromagnetic compatibility EU: in line with EMC Directive 2004/108/EC Electrical safety Dimensions EU: in line with Low Voltage Directive 2006/95/EC W H D Weight incl. R&S TS-PDC 0.14 kg (0.3 lb) Recommended calibration interval applied harmonized standards: EN (industrial environment), EN , EN (class A), EN , EN applied harmonized standard: EN mm 174 mm 20 mm (12.44 in 6.85 in 0.79 in) 0.55 kg (1.2 lb) 12 months Rohde & Schwarz R&S TS-PSAM Analog Source and Measurement Module 8 TS-PSAM_bro_en_ indd 8

9 Ordering information Designation Type Order No. Analog Source and Measurement Module, including R&S TS-PDC R&S TS-PSAM Platform R&S CompactTSVP R&S TS-PCA Rohde & Schwarz R&S TS-PSAM Analog Source and Measurement Module 9 TS-PSAM_bro_en_ indd :34:46

10 Service that adds value Worldwide Local and personalized Customized and ﬂexible Uncompromising quality Long-term dependability About Rohde & Schwarz Rohde & Schwarz is an independent group of companies specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, broadcasting, radiomonitoring and radiolocation, as well as secure communications. Established more than 75 years ago, Rohde & Schwarz has a global presence and a dedicated service network in over 70 countries. Company headquarters are in Munich, Germany. Environmental commitment Energy-efficient products Continuous improvement in environmental sustainability ISO certified environmental management system Certified Quality System ISO 9001 Rohde & Schwarz GmbH & Co. KG R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG Trade names are trademarks of the owners PD Version December 2013 (wb) R&S TS-PSAM Data without tolerance limits is not binding Subject to change Rohde & Schwarz GmbH & Co. KG München, Germany PDP 1 en Regional contact Europe, Africa, Middle East customersupport@rohde-schwarz.com North America TEST RSA ( ) customer.support@rsa.rohde-schwarz.com Latin America customersupport.la@rohde-schwarz.com Asia/Pacific customersupport.asia@rohde-schwarz.com China / customersupport.china@rohde-schwarz.com TS-PSAM_bro_en_ indd :36:32

R&S RSC Step Attenuator Specifications

R&S RSC Step Attenuator Specifications Data Sheet Version 05.00 CONTENTS Definitions... 3 Specifications... 4 Step attenuator, 139 db, 1 db steps, DC to 6 GHz (models.03 and.13)... 4 Step attenuator, 139.9