NI 6023E/6024E/6025E Family Specifications
|
|
- Emma Fox
- 1 years ago
- Views:
Transcription
1 NI 6023E/6024E/6025E Family Specifications This document lists the I/O terminal summary and specifications for the devices that make up the NI 6023E/6024E/6025E family of devices. This family includes the following devices: NI DAQCard-6024E NI PCI-6023E NI PCI-6024E NI PCI/PXI-6025E For the most current edition of this document, refer to ni.com/manuals. For more information about using your E Series device, refer to the E Series Help at ni.com/manuals or on your NI-DAQ CD. Refer to the DAQ Quick Start Guide for more information about accessing documents on the NI-DAQ CD. Note With NI-DAQmx, National Instruments has revised its terminal names so they are easier to understand and more consistent among NI hardware and software products. The revised terminal names used in this document are usually similar to the names they replace. For a complete list of Traditional NI-DAQ terminal names and their NI-DAQmx equivalents, refer to the Terminal Name Equivalents table in the E Series Help. Table 1. I/O Terminal Summary Terminal Name Terminal Type and Direction Impedance Input/ Output Protection (Volts) On/Off Source (ma at V) Sink (ma at V) Rise Time (ns) Bias AI <0..15> AI 100 GΩ in parallel with 100 pf AI SENSE AI 100 GΩ in parallel with 100 pf 42/35 ±200 pa 40/25 ±200 pa AI GND
2 Table 1. I/O Terminal Summary (Continued) Terminal Name Terminal Type and Direction Impedance Input/ Output Protection (Volts) On/Off Source (ma at V) Sink (ma at V) Rise Time (ns) Bias AO 0 1 AO 0.1 Ω Shortcircuit to ground AO 1 1 AO 0.1 Ω Shortcircuit to ground 5 at 10 5 at V/µs 5 at 10 5 at V/µs AO GND D GND +5 V 0.1 Ω Shortcircuit to ground 1 A fused P0.<0..7> DIO V CC at P1.<0..7> 2 DIO V CC at 3.7 min P2.<0..7> 2 DIO V CC at 3.7 min P3.<0..7> 2 DIO V CC at 3.7 min 24 at kω pu 2.5 at kω pu 2.5 at kω pu 2.5 at kω pu AI HOLD COMP or AI HOLD DO 3.5 at EXTSTROBE* DO 3.5 at PFI 0/(AI START TRIG) PFI 1/(AI REF TRIG) PFI 2/(AI CONV CLK)* PFI 3/CTR 1 SOURCE DIO V CC at DIO V CC at DIO V CC at DIO V CC at PFI 4/CTR 1 GATE DIO V CC at CTR 1 OUT DO 3.5 at PFI 5/(AO SAMP CLK)* DIO V CC at NI 6023E/6024E/6025E Family Specifications 2 ni.com
3 Table 1. I/O Terminal Summary (Continued) Terminal Name Terminal Type and Direction Impedance Input/ Output Protection (Volts) On/Off Source (ma at V) Sink (ma at V) Rise Time (ns) Bias PFI 6/(AO START TRIG) PFI 7/(AI SAMP CLK) PFI 8/CTR 0 SOURCE DIO V CC at DIO V CC at DIO V CC at PFI 9/CTR 0 GATE DIO V CC at CTR 0 OUT DO 3.5 at FREQ OUT DO 3.5 at * Indicates active low 1 NI PCI-6024E and NI 6025E only 2 NI 6025E only AI = Analog Input DIO = Digital Input/Output pu = pull-up AO = Analog Output DO = Digital Output Note: The tolerance on the 50 kω pull-up resistors is large. Actual value might range between 17 kω and 100 kω. Specifications The following specifications are typical at 25 C unless otherwise noted. Analog Input Input Characteristics Number of channels single-ended or 8 differential (software-selectable per channel) Type of A/D converter (ADC)... Successive approximation Resolution bits, 1 in 4,096 Max sampling rate ks/s guaranteed National Instruments Corporation 3 NI 6023E/6024E/6025E Family Specifications
4 Input signal ranges (bipolar only) Range Bipolar 20 V ±10 V 10 V ±5 V 1V ±500 mv Input coupling...dc Max working voltage (signal + common mode)...each input should remain within ±11 V of ground Overvoltage protection 100 mv ±50 mv Signal Powered On Powered Off AI <0..15> ±42 ±35 AI SENSE ±40 ±25 FIFO buffer size NI DAQCard-6024E...2,048 samples (S) NI 6023E, NI PCI-6024E, NI 6025E S DMA (PCI/PXI only) Channels...1 Data sources/destinations...analog input, analog output, counter/timer 0, or counter/timer 1 Data transfers...direct memory access (DMA) 1, interrupts, programmed I/O DMA 1 modes...scatter-gather (single transfer, demand transfer) Configuration memory size words (1 word = 8 bits) 1 No DMA on the NI DAQCard-6024E. NI 6023E/6024E/6025E Family Specifications 4 ni.com
5 Accuracy Information NI DAQCard-6024E Absolute Accuracy Relative Accuracy Nominal Range (V) Positive Full Scale Negative Full Scale % of Reading 24 Hours 1 Year Offset (mv) Noise + Quantization (mv) Single Pt. Averaged Temp Drift (%/ C) Absolute Accuracy at Full Scale (mv) Resolution (mv) Single Pt. Averaged Note: Accuracies are valid for measurements following an internal E Series calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 C of internal calibration temperature and ±10 C of external or factory-calibration temperature. NI recommends a one-year calibration interval. The Absolute Accuracy at Full Scale calculations were performed for a maximum range input voltage (for example, 10 V for the ±10 V range) after one year, assuming 100 points of averaged data. NI 6023E, NI PCI-6024E, NI 6025E Absolute Accuracy Relative Accuracy Nominal Range (V) Positive Full Scale Negative Full Scale % of Reading 24 Hours 1 Year Offset (mv) Noise + Quantization (mv) Single Pt. Averaged Temp Drift (%/ C) Absolute Accuracy at Full Scale (mv) Resolution (mv) Single Pt. Averaged Note: Accuracies are valid for measurements following an internal E Series calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 C of internal calibration temperature and ±10 C of external or factory-calibration temperature. NI recommends a one-year calibration interval. The Absolute Accuracy at Full Scale calculations were performed for a maximum range input voltage (for example, 10 V for the ±10 V range) after one year, assuming 100 points of averaged data. National Instruments Corporation 5 NI 6023E/6024E/6025E Family Specifications
6 Transfer Characteristics Relative accuracy Dithered...±0.5 LSB typ Undithered...±1.5 LSB max Differential nonlinearity (DNL) NI DAQCard-6024E...±0.75 LSB typ, 0.9 to +1.5 LSB max NI 6023E, NI PCI-6024E, NI 6025E...±0.5 LSB typ, ±1.0 LSB max No missing codes...12 bits, guaranteed Offset error Pregain error after calibration...±12 µv max Pregain error before calibration...±28 mv max Postgain error after calibration...±0.5 mv max Postgain error before calibration...±100 mv max Gain error (relative to calibration reference) After calibration (gain = 1)...±0.02% of reading max Before calibration...±2.75% of reading max Gain 1 with gain error adjusted to 0 at gain = 1...±0.05% of reading max Amplifier Characteristics Input impedance Normal powered on GΩ in parallel with 100 pf Powered off kω Overload kω Input bias current...±200 pa Input offset current...±100 pa Common-mode rejection ratio (CMRR), DC to 60 Hz Range 10 to 20 mv...85 db Range 100 mv to 1 V...90 db NI 6023E/6024E/6025E Family Specifications 6 ni.com
7 Dynamic Characteristics Bandwidth Small signal ( 3 db) khz Large signal (1% THD) NI DAQCard-6024E khz NI PCI-6023E, NI PCI-6024E, NI 6025E khz Settling time for full-scale step... 5 µs typ to ±0.5 LSB accuracy 1 System noise (LSB rms, not including quantization) Device Range Dither Off Dither On NI DAQCard-6024E 10 to 20 V V mv NI 6023E, NI PCI-6024E, NI 6025E 1 to 20 V mv Crosstalk db, DC to 100 khz Stability Recommended warm-up time NI DAQCard-6024E minutes NI 6023E, NI PCI-6024E, NI 6025E minutes Offset temperature coefficient Pregain... ±15 µv/ C Postgain... ±240 µv/ C Gain temperature coefficient... ±25 ppm/ C 1 Accuracy values are valid for source impedances <1 kω. Refer to Multichannel Scanning Considerations in the E Series Help for more information. National Instruments Corporation 7 NI 6023E/6024E/6025E Family Specifications
8 Analog Output (NI 6024E/6025E Only) Output Characteristics Number of channels...2 voltage Resolution...12 bits, 1 in 4,096 Max update rate DMA khz, system dependent Interrupts...1 khz, system dependent Type of D/A converter (DAC)...Double buffered, multiplying FIFO buffer size...none Data transfers...dma 1, interrupts, programmed I/O DMA 1 modes...scatter-gather (single transfer, demand transfer) Accuracy Information NI DAQCard-6024E Nominal Range (V) Positive Full Scale % of Reading Absolute Accuracy Negative Full Scale 24 Hours 90 Days 1 Year Offset (mv) Temp Drift (%/ C) Absolute Accuracy at Full Scale (mv) Note: Temp Drift applies only if ambient is greater than ±10 C of previous external calibration. NI PCI-6024E, NI 6025E Nominal Range (V) Positive Full Scale % of Reading Absolute Accuracy Negative Full Scale 24 Hours 90 Days 1 Year Offset (mv) Temp Drift (%/ C) Absolute Accuracy at Full Scale (mv) Note: Temp Drift applies only if ambient is greater than ±10 C of previous external calibration. 1 No DMA on the NI DAQCard-6024E. NI 6023E/6024E/6025E Family Specifications 8 ni.com
9 Transfer Characteristics Relative accuracy, or integral nonlinearity (INL) After calibration NI DAQCard-6024E... ±0.5 LSB typ, ±1.0 LSB max NI PCI-6024E, NI 6025E... ±0.3 LSB typ, ±0.5 LSB max Before calibration... ±4 LSB max DNL After calibration NI DAQCard-6024E... ±0.5 LSB typ, ±1.0 LSB max NI PCI-6024E, NI 6025E... ±0.3 LSB typ, ± 1.0 LSB max Before calibration... ±3 LSB max Monotonicity bits, guaranteed after calibration Offset error After calibration... ±1.0 mv max Before calibration... ±200 mv max Gain error (relative to internal reference) After calibration... ±0.01% of output max Before calibration... ±0.75% of output max Voltage Output Range... ±10 V Output coupling... DC Output impedance Ω max Current drive... ±5 ma max Protection... Short-circuit to ground Power-on state (steady state)... ±200 mv Initial power-up glitch Magnitude NI DAQCard-6024E... ±1.5 V NI PCI-6024E, NI 6025E... ±1.1 V National Instruments Corporation 9 NI 6023E/6024E/6025E Family Specifications
10 Duration NI DAQCard-6024E s NI PCI-6024E, NI 6025E ms Power reset glitch Magnitude NI DAQCard-6024E...±1.5 V NI PCI-6024E, NI 6025E...±2.2 V Duration NI DAQCard-6024E s NI PCI-6024E, NI 6025E µs Dynamic Characteristics Settling time for full-scale step...5 µs typ to ±0.5 LSB accuracy 1 5 µs max to ±1.0 LSB accuracy Slew rate...10 V/µs Noise µv rms, DC to 1 MHz Midscale transition glitch Magnitude NI DAQCard-6024E...±13 mv NI PCI-6024E, NI 6025E...±42 mv Duration µs Stability Offset temperature coefficient...±50 µv/ C Gain temperature coefficient...±25 ppm/ C Digital I/O Number of channels NI DAQCard-6024E, NI 6023E, NI PCI-6024E...8 input/output NI 6025E...32 input/output Compatibility...5 V TTL 1 Accuracy values are valid for source impedances <1 kω. Refer to Multichannel Scanning Considerations in the E Series Help for more information. NI 6023E/6024E/6025E Family Specifications 10 ni.com
11 NI 6023E/6024E Digital logic levels on P0.<0..7> Level Min Max Input low voltage Input high voltage Input low current (V in = 0 V) Input high current (V in = 5 V) Output low voltage (I OL = 24 ma) Output high voltage (I OH = 13 ma) 0 V 2 V 4.35 V 0.8 V 5 V 320 µa 10 µa 0.4 V Power-on state... Input (high-impedance), 50 kω pull-up to +5 VDC Data transfers... Programmed I/O NI 6025E Digital logic levels on P1.<0..7>, P2.<0..7>, and P3.<0..7> Level Min Max Input low voltage Input high voltage Input low current (V in = 0 V, 100 kω pull-up) Input high current (V in = 5 V, 100 kω pull-up) Output low voltage (I OL = 2.5 ma) Output high voltage (I OH = 2.5 ma) Handshaking... 2-wire 0 V 2.2 V 3.7 V 0.8 V 5 V 75 µa 10 µa 0.4 V Power-on state P1.<0..7>... Input (high-impedance), 100 kω pull-up to +5 VDC P2.<0..7>... Input (high-impedance), 100 kω pull-up to +5 VDC P3.<0..7>... Input (high-impedance), 100 kω pull-up to +5 VDC Data transfers... Interrupts, programmed I/O National Instruments Corporation 11 NI 6023E/6024E/6025E Family Specifications
12 Timing I/O Number of channels...2 up/down counter/timers, 1 frequency scaler Resolution Counter/timers...24 bits Frequency scalers...4 bits Compatibility...5 V/TTL Base clocks available Counter/timers...20 MHz, 100 khz Frequency scalers...10 MHz, 100 khz Base clock accuracy...±0.01% Max source frequency Up/down counter/timers...20 MHz Min source pulse duration...10 ns in edge-detect mode Min gate pulse duration...10 ns in edge-detect mode Data transfers...dma 1, interrupts, programmed I/O DMA 1 modes...scatter-gather (single transfer, demand transfer) Triggers Digital Trigger Purpose Analog input...start, reference, and pause trigger, sample clock Analog output...start and pause trigger, sample clock Counter/timers...Source, gate External sources...pfi <0..9>, RTSI <0..6> 2 Compatibility...5 V TTL 1 No DMA on the NI DAQCard-6024E. 2 No RTSI on the NI DAQCard-6024E. NI 6023E/6024E/6025E Family Specifications 12 ni.com
13 Response... Rising or falling edge Pulse width ns min RTSI 1 Trigger lines... 7 Calibration Recommended warm-up time NI DAQCard-6024E minutes NI 6023E, NI PCI-6024E, NI 6025E minutes Power Requirement Interval... 1 year External calibration reference... Between 6 and 10 V Onboard calibration reference Level V (±3.5 mv), actual value stored in EEPROM Temperature coefficient... ±5 ppm/ C max Long-term stability... ±15 ppm/ 1,000 h +5 VDC (±5%) NI DAQCard-6024E ma typ, 750 ma max NI 6023E, NI PCI-6024E, NI 6025E A Note Excludes power consumed through +5 V available at the I/O connector. Power available at I/O connector NI DAQCard-6024E to VDC at 250 ma NI 6023E, NI PCI-6024E, NI 6025E to VDC at 1 A 1 No RTSI on the NI DAQCard-6024E. National Instruments Corporation 13 NI 6023E/6024E/6025E Family Specifications
14 Physical Dimensions (not including connectors) PCI devices by 10.7 cm (6.9 by 4.2 in.) PXI devices by 10.0 cm (6.3 by 3.9 in.) Maximum Working Voltage NI DAQCard-6024E PC card type...type II I/O connector NI DAQCard-6024E...68-position VHDCI female connector NI 6023E, NI PCI-6024E...68-pin male SCSI-II type NI 6025E pin female 0.05D type Channel-to-earth...42 V, Installation Category II Channel-to-channel...42 V, Installation Category II Environmental Operating temperature NI DAQCard-6024E...0 to 40 C with a maximum internal device temperature of 70 C as measured by onboard temperature sensor; case temperature should not exceed 55 C NI 6023E, NI PCI-6024E, NI 6025E...0 to 55 C Storage temperature to 70 C Relative humidity...10 to 90%, noncondensing Maximum altitude...2,000 m Pollution Degree (indoor use only)...2 NI 6023E/6024E/6025E Family Specifications 14 ni.com
15 NI PXI-6025E Functional shock... MIL-T E Class 3 (per Section ) half-sine shock pulse, 11 ms duration, 30 g peak, 30 shocks per face Operational random vibration... 5 to 500 Hz, 0.31 g rms, 3 axes Non-operational random vibration... 5 to 500 Hz, 2.5 g rms, 3 axes Note Random vibration profiles for the NI PXI-6025E were developed in accordance with MIL-T-28800E and MIL-STD-810E Method 514. Test levels exceed those recommended in MIL-STD-810E for Category 1, Basic Transportation. Safety NI PCI-6023E/6024E/6025E, NI PXI-6025E The device meets the requirements of the following standards for safety and electrical equipment for measurement, control, and laboratory use: IEC , EN UL , UL 61010B-1 CAN/CSA C22.2 No NI DAQCard-6024E The device meets the requirements of the following standards for safety and electrical equipment for measurement, control, and laboratory use: IEC 60950, EN UL 1950, UL CAN/CSA C22.2 No Note For UL and other safety certifications, refer to the product label, or visit ni.com/hardref.nsf, search by model number or product line, and click the appropriate link in the Certification column. National Instruments Corporation 15 NI 6023E/6024E/6025E Family Specifications
16 Electromagnetic Compatibility Emissions...EN Class A at 10 m FCC Part 15A above 1 GHz Immunity...EN 61326:1997 A2:2001, Table 1 CE, C-Tick, and FCC Part 15 (Class A) Compliant Note For EMC compliance, you must operate this device with shielded cabling. CE Compliance This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: Low-Voltage Directive (safety)...73/23/eec Electromagnetic Compatibility Directive (EMC)...89/336/EEC Note Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/hardref.nsf, search by model number or product line, and click the appropriate link in the Certification column. DAQCard, National Instruments, NI, ni.com, NI-DAQ, and RTSI are trademarks of National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents National Instruments Corp. All rights reserved. *370719B-01* B-01 Sep03
NI 6040E Family Specifications
NI 6040E Family Specifications This document lists the I/O terminal summary and specifications for the devices that make up the NI 6040E family of devices. This family includes the following devices: NI
Specifications. PCI Bus. Analog Input Input Characteristics
Specifications A This appendix lists the specifications of the NI 6034E/6035E/6036E. These specifications are typical at 25 C unless otherwise noted. The first section provides the specifications for the
NI PXI-4461 Specifications
NI PXI-446 Specifications Analog Input Input Characteristics This document lists specifications for the NI PXI-446 Dynamic Signal Acquisition (DSA) device. These specifications are typical at 5 C unless
NI 6230 Specifications
NI 6230 Specifications Specifications listed below are typical at 25 C unless otherwise noted. Analog Input Number of channels... 4 differential or 8singleended ADC resolution... 6 bits DNL... No missing
SCC-ACC01 Accelerometer Input Module
USER GUIDE SCC-ACC01 Accelerometer Input Module Conventions The SCC-ACC01 accelerometer (ACC) input module accepts an active accelerometer input signal, passes it through a 0.8 Hz highpass filter, amplifies
NI 622x Specifications
NI 622x Specifications Specifications listed below are typical at 25 C unless otherwise noted. Refer to the M Series User Manual for more information about NI 622x devices. Analog Input Number of channels
Specifications for the NI PXI/PCI-6552/6551
Specifications for the NI PXI/PCI-6552/6551 100/50 MHz Digital Waveform Generator/Analyzer Channel Characteristics These specifications are valid for the operating temperature range, unless otherwise noted.
NI PXI-2532 Specifications
NI PXI-2532 Specifications 512-Crosspoint, 1-Wire Matrix This document lists specifications for the National Instruments PXI-2532 512-crosspoint, 1-wire matrix. All specifications are subject to change
SCC-DI01 Isolated Digital Input Module
USER GUIDE SCC-DI01 Isolated Digital Input Module Conventions The SCC-DI01 is a single-channel, optically isolated digital input module that can sense AC and DC digital signals, including TTL, up to 30
Analog Input SPECIFICATIONS NI 6320/6321/6323
SPECIFICATIONS NI 6320/6321/6323 Français Deutsch ni.com/manuals Specifications listed below are typical at 25 C unless otherwise noted. Refer to the X Series User Manual for more information about NI
NI PXI/PCI-5411/5431 Specifications
NI PXI/PCI-5411/5431 Specifications NI PXI/PCI-5411 High-Speed Arbitrary Waveform Generator NI PXI/PCI-5431 Video Waveform Generator Analog Output This document lists the specifications for the NI PXI/PCI-5411
NI PXI/PCI-5411/5431 Specifications
NI PXI/PCI-5411/5431 Specifications NI PXI/PCI-5411 High-Speed Arbitrary Waveform Generator NI PXI/PCI-5431 Video Waveform Generator Analog Output This document lists the specifications for the NI PXI/PCI-5411
Input Characteristics. Measurement Range. SPECIFICATIONS NI PXIe-4357
SPECIFICATIONS NI PXIe-4357 This document lists specifications for the NI PXIe-4357 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must be allowed
Analog Input. DEVICE SPECIFICATIONS NI PXIe-4300
DEVICE SPECIFICATIONS NI PXIe-4300 This document lists specifications for the NI PXIe-4300 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must
NI PXIe-5630 Specifications
NI PXIe-5630 Specifications RF Vector Network Analyzer This document lists specifications for the NI PXIe-5630 RF vector network analyzer (NI 5630). Specifications are warranted under the following conditions:
SPECIFICATIONS FOR THE NI PXI/PCI-4060
SPECIFICATIONS FOR THE NI PXI/PCI-4060 This document lists the specifications of the NI PXI/PCI-4060. These specifications are guaranteed between 15 and 35 C unless otherwise specified. DC Voltage (% of
NI PXIe-5601 Specifications
NI PXIe-5601 Specifications RF Downconverter This document lists specifications for the NI PXIe-5601 RF downconverter (NI 5601). Use the NI 5601 with the NI PXIe-5622 IF digitizer and the NI PXI-5652 RF
DEVICE SPECIFICATIONS NI PXIe-4302/ Ch, 24-bit, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module
DEVICE SPECIFICATIONS NI PXIe-4302/4303 32 Ch, 24-bit, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module This document lists specifications for the NI PXIe-4302/4303 simultaneous filtered
DEVICE SPECIFICATIONS NI PXIe-4304/ Ch, 24-bit, ±42 V, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module. ni.
DEVICE SPECIFICATIONS NI PXIe-4304/4305 32 Ch, 24-bit, ±42 V, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module Français Deutsch ni.com/manuals This document lists specifications for the
NI PXI/PCI-6561/6562 Specifications
NI PXI/PCI-6561/6562 Specifications 100/200 MHz Digital Waveform Generator/Analyzer Contents This document provides the specifications for the NI PXI/PCI-6561 (NI 6561) and the NI PXI/PCI-6562 (NI 6562),
NI PXI-2530 Specifications
NI PXI-2530 Specifications 128-Channel Reed Relay Multiplexer/Matrix This document lists specifications for the National Instruments PXI-2530 128-channel multiplexer/matrix module. All specifications are
NI PXI/PXIe-2532 Specifications
NI PXI/PXIe-2532 Specifications 512-Crosspoint, 1-Wire Matrix This document lists specifications for the NI PXI/PXIe-2532 (NI 2532) 512-crosspoint matrix. All specifications are subject to change without
M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 2 AO, 24 DIO Sinking, Voltage Input/Output Bank Isolation
DEVICE SPECIFICATIONS NI 6233 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 2 AO, 24 DIO Sinking, Voltage Input/Output Bank Isolation The following specifications are typical at 25 C, unless otherwise
M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 4 AO, 6 DI, 4 DO, Voltage Input/Output, Bank Isolation
DEVICE SPECIFICATIONS NI 6230 M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 4 AO, 6 DI, 4 DO, Voltage Input/Output, Bank Isolation The following specifications are typical at 25 C, unless otherwise
NI 5421 Specifications NI PXI/PCI Bit 100 MS/s Arbitrary Waveform Generator
NI 5421 Specifications NI PXI/PCI-5421 16-Bit 100 MS/s Arbitrary Waveform Generator Unless otherwise noted, the following conditions were used for each specification: Contents Analog Filter enabled. Interpolation
NI PXI/PXIe-2527 Specifications
NI PXI/PXIe-2527 Specifications 32 1 Relay Multiplexer This document lists specifications for the NI PXI/PXIe-2527 (NI 2527) 32 1 multiplexer relay module. All specifications are subject to change without
INSTALLATION GUIDE BNC-2120 Connector Accessory for E/M/S Series Devices. Contents
INSTALLATION GUIDE BNC-2120 Connector Accessory for E/M/S Series Devices Contents This installation guide describes how to install, configure, and use your BNC-2120 accessory with 68-pin or 100-pin E/M/S
16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device
SPECIFICATIONS USB-6210 16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device Definitions Warranted specifications describe the performance of a model under stated operating conditions and
NI PXI/PCI-5122 Specifications
NI PXI/PCI-5122 Specifications 14-Bit 100 MS/s Digitizer Contents Unless otherwise noted, the following conditions were used for each specification: All filter settings All impedance selections Sample
NI 6356/6358 Specifications
NI 6356/6358 Specifications Français Deutsch ni.com/manuals Specifications listed below are typical at 25 C unless otherwise noted. Refer to the X Series User Manual for more Analog Input Number of channels
Terminology. Output Characteristics. DEVICE SPECIFICATIONS NI PXIe-4463 DSA Analog Output. ni.com/manuals
DEVICE SPECIFICATIONS NI PXIe-4463 DSA Analog Output Français Deutsch ni.com/manuals This document lists specifications for the NI PXIe-4463 Dynamic Signal Acquisition (DSA) analog output module. All specifications
Table 2. Differences Between the USB-6008 and USB Feature USB-6008 USB bits differential, 13 bits single-ended Maximum AI Sample Rate,
USER GUIDE AND SPECIFICATIONS USB-6008/6009 Introduction This guide describes how to use the National Instruments USB-6008/6009 data acquisition (DAQ) devices and lists specifications. The NI USB-6008/6009
SPECIFICATIONS PXIe channel, 16-bit, 400 ks/s/ch, Ch-Ch Isolated Analog Input Module. ni.com/manuals
SPECIFICATIONS PXIe-4310 8-channel, 16-bit, 400 ks/s/ch, Ch-Ch Isolated Analog Input Module Français Deutsch ni.com/manuals This document lists specifications for the PXIe-4310 module. These specifications
NI PXI/PXIe-2541 Specifications 300 MHz Ω Matrix
NI PXI/PXIe-2541 Specifications 3 MHz 8 12 5 Ω Matrix This document lists specifications for the NI PXI/PXIe-2541 (NI 2541) matrix module. All specifications are subject to change without notice. Visit
USB-TEMP and TC Series USB-Based Temperature Measurement Devices
USB-Based Temperature Measurement Devices Features Temperature and voltage measurement USB devices Thermocouple, RTD, thermistor, or semiconductor sensor measurements Eight analog inputs Up to ±10 V inputs*
M Series Data Acquisition: 32 AI, 1.25 MS/s, 48 DIO
DEVICE SPECIFICATIONS NI 6254 M Series Data Acquisition: 32 AI, 1.25 MS/s, 48 DIO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6254, refer
PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer,PXI Digital Multimeter
SPECIFICATIONS PXIe-4080 PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer,PXI Digital Multimeter These specifications apply to the PXIe-4080. Contents Definitions...2 Conditions... 2 DC Voltage
6 1 2-Digit Digital Multimeter, 1.8 MS/s Isolated Digitizer, and LCR Meter
NI PXI-4072 FlexDMM Superior accuracy and measurement rates Multifunction device 6 1 2-digit digital multimeter 1.8 MS/s isolated digitizer LCR meter (inductance, capacitance, and resistance) 20 built-in
PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer
SPECIFICATIONS PXIe-5632 8.5 GHz Vector Network Analyzer Contents Definitions...1 Conditions... 2 General Information...2 Source Characteristics...3 Receiver Characteristics...5 Measurement Speed... 6
SCXI MHz Quad 8x1 50 Ω Multiplexer
SPECIFICATIONS SCXI -1193 500 MHz Quad 50 Ω Multiplexer This document lists specifications for the SCXI-1193 multiplexer module. All specifications are subject to change without notice. Visit ni.com/manuals
R Series for USB Multifunction RIO with Kintex-7 70T FPGA. may impair the protection the NI USB-7855R provides.
SPECIFICATIONS NI USB-7855R R Series for USB Multifunction RIO with Kintex-7 70T FPGA This document contains the specifications for the NI USB-7855R. Specifications are typical at 25 C unless otherwise
4-Channel, ±24 V, 150 ma PXI Source Measure Unit
SPECIFICATIONS PXIe-4142 4-Channel, ±24 V, 150 ma PXI Source Measure Unit These specifications apply to the PXIe-4142. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...
Racal Instruments. Product Information
Racal Instruments 6084A-104-DMM 1 GHz Digitizer and 7.5 Digit Digital Multimeter The Digitizer/DMM increases test system performance and density by packaging a 7.5 digit Digital Multimeter (DMM) together
6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device
SPECIFICATIONS PCI-4070 6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device These specifications apply to the PCI-4070. Contents Definitions...2 Conditions... 2 DC Specifications...
OPERATING INSTRUCTIONS AND SPECIFICATIONS. NI 9207E 16-Channel, ±20 ma/±10 V, 24-Bit Analog Input Module
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9207E 16-Channel, ±20 ma/±10 V, 24-Bit Analog Input Module This document describes how to use the National Instruments 9207E and includes dimensions, pin assignments,
Isolated 32 AI (16-Bit, 250 ks/s), 2 AO (250 ks/s), 8 DI, 8 DIO USB Multifunction I/O Device
SPECIFICATIONS USB-6218 Isolated 32 AI (16-Bit, 250 ks/s), 2 AO (250 ks/s), 8 DI, 8 DIO USB Multifunction I/O Device These specifications apply to the USB-218 BNC and USB-6218 Spring Terminal. Definitions
16 AI (16-Bit, 400 ks/s), 2 AO (250 ks/s), Up to 32 DIO USB Multifunction I/O Device
SPECIFICATIONS USB-6212 16 AI (16-Bit, 400 ks/s), 2 AO (250 ks/s), Up to 32 DIO USB Multifunction I/O Device These specifications apply to the USB-6212 BNC, USB-6212 Mass Termination, and USB-6212 Spring
PXI Timing and Synchronization Control
NI PXI-665x Works with all PXI modules Multichassis PXI synchronization Onboard routing of internal or external clock and trigger signals PXI slot 2 star trigger controller Onboard high-stability references
SCC-CO20 Isolated Current Output Module
USER GUDE SCC-CO0 solated Current Output Module Conventions The SCC-CO0 is an isolated current output module that outputs up to 0 ma. The output current level is proportional to the voltage applied to
R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA
SPECIFICATIONS NI PXIe-7846R R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA This document contains the specifications for the NI PXIe-7846R.
NI 6221 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 24 DIO, 2 AO
DEVICE SPECIFICATIONS NI 6221 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 24 DIO, 2 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI
PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
SPECIFICATIONS PCIe-4065 PCI Express, 6½-Digit, ±300 V Digital Multimeter Device These specifications apply to the PCIe-4065. Contents Definitions...1 Conditions... 2 DC Specifications... 2 DC System Speed
16-Bit, 120 MS/s, 12 Channel DC/16 Channel AC Receiver Adapter Module
SPECIFICATIONS NI 5753 16-Bit, 120 MS/s, 12 Channel DC/16 Channel AC Receiver Adapter Module This document lists specifications for the NI 5753 adapter module. Pair these specifications with the specifications
NI USB Contents DEVICE SPECIFICATIONS. 50 MS/s Bus-Powered USB Oscilloscope
DEVICE SPECIFICATIONS NI USB-5132 50 MS/s Bus-Powered USB Oscilloscope This document lists specifications for the NI USB-5132 (NI 5132). Unless otherwise noted, these specifications are valid for the following
SPECIFICATIONS PXIe ks/s, 119 db, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module
SPECIFICATIONS PXIe-4464 24.8 ks/s, 119 db, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module This document lists specifications for the PXIe-4464 Dynamic Signal Acquisition (DSA) analog input
M Series Data Acquisition: 80 AI, 1.25 MS/s, 24 DIO, 2 AO
DEVICE SPECIFICATIONS NI 6255 M Series Data Acquisition: 80 AI, 1.25 MS/s, 24 DIO, 2 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6255,
PXI Contents. PXI-2585 Specifications. Topology DEVICE SPECIFICATIONS. 10-Channel Multiplexer
DEVICE SPECIFICATIONS PXI-2585 10-Channel Multiplexer This document lists specifications for the PXI-2585 general-purpose relay module. All specifications are subject to change without notice. Visit ni.com/manuals
M Series Data Acquisition: 18-Bit, 625 ks/s, 32 AI, 48 DIO, 4 AO
DEVICE SPECIFICATIONS NI 6289 M Series Data Acquisition: 18-Bit, 625 ks/s, 32 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI
X Series Data Acquisition: 2 MS/s/ch, 16 AI, 48 DIO, 4 AO
DEVICE SPECIFICATIONS NI 6368 X Series Data Acquisition: 2 MS/s/ch, 16 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6368,
Industrial M Series Multifunction DAQ 16-Bit, ±10 V/±20 ma Analog I/O, 5 V/24 V Digital I/O
Technical Sales (866) 531-6285 orders@ni.com Requirements and Compatibility Ordering Information Detailed Specifications Pinouts/Front Panel Connections For user manuals and dimensional drawings, visit
NI PXI-5422 Specifications 16-Bit 200 MS/s Arbitrary Waveform Generator
NI PXI-5422 Specifications 16-Bit 200 MS/s Arbitrary Waveform Generator Français Deutsch ni.com/manuals Unless otherwise noted, the following conditions were used for each specification: Analog filter
NI PXI/PCI-5421 Specifications 16-Bit 100 MS/s Arbitrary Waveform Generator
NI PXI/PCI-5421 Specifications 16-Bit 100 MS/s Arbitrary Waveform Generator This document lists specifications for the NI PXI-5421 arbitrary waveform generator. Unless otherwise noted, the following conditions
Appendix A: Specifications
All specifications apply to the TDS 200-Series Digital Oscilloscopes and a P2100 probe with the Attenuation switch set to 10X unless noted otherwise. To meet specifications, two conditions must first be
NI PXI/PCI-5412 Specifications 14-Bit 100 MS/s Arbitrary Waveform Generator
NI PXI/PCI-5412 Specifications 14-Bit 100 MS/s Arbitrary Waveform Generator This document lists specifications for the NI PXI/PCI-5412 arbitrary waveform generator. Unless otherwise noted, the following
X Series Data Acquisition: 1.25 MS/s, 32 AI, 48 DIO, 4 AO
DEVICE SPECIFICATIONS NI 6353 X Series Data Acquisition: 1.25 MS/s, 32 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6353,
PXIe Contents. Required Software CALIBRATION PROCEDURE
CALIBRATION PROCEDURE PXIe-5160 This document contains the verification and adjustment procedures for the PXIe-5160. Refer to ni.com/calibration for more information about calibration solutions. Contents
NI PXIe-5171R. Contents. Required Software CALIBRATION PROCEDURE
CALIBRATION PROCEDURE NI PXIe-5171R This document contains the verification and adjustment procedures for the NI PXIe-5171R (NI 5171R). Refer to ni.com/calibration for more information about calibration
Contents. CALIBRATION PROCEDURE NI PXIe-4463 DSA Analog Output
CALIBRATION PROCEDURE NI PXIe-4463 DSA Analog Output This document contains the verification and adjustment procedures for the National Instruments PXIe-4463 with either BNC or mini-xlr connectors. For
z8801 Local Oscillator PXI
TECHNICAL SPECIFICATIONS z8801 Local Oscillator PXI 2014 LitePoint, A Teradyne Company. All rights reserved. Port Descriptions Front Panel Label Type Description REF OUT SMA Backplane reference clock output
PXI Contents SPECIFICATIONS. 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
SPECIFICATIONS PXI-4072 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter These specifications apply to the PXI-4072. Contents Definitions...2 Conditions...
FP-RLY-420. Features. Installing the FP-RLY-420. FieldPoint Operating Instructions. Eight-Channel SPST Relay Module
FieldPoint Operating Instructions FP-RLY-420 Eight-Channel SPST Relay Module These operating instructions describe how to install and use the National Instruments FP-RLY-420 relay module, revision 185151C-01
Related Information Refer to the NI Switches Help for detailed topology information.
SPECIFICATIONS NI PXI-2530B 128-Channel Reed Relay Multiplexer/Matrix This document lists specifications for the NI PXI-2530B 128-channel multiplexer/matrix module (NI 2530B). All specifications are subject
100 MHz, 32-Channel, 5 V PXI Digital Waveform Instrument
SPECIFICATIONS PXI-6542 100 MHz, 32-Channel, 5 V PXI Digital Waveform Instrument These specifications apply to the PXI-6542 with 1 MBit, 8 MBit, and 64 MBit of memory per channel. Contents Hot Surface
5520A. Multi-Product Calibrator. Extended Specifications 2005
5520A Multi-Product Calibrator Extended Specifications 2005 5520A Specifications The following tables list the 5520A specifications. All specifications are valid after allowing a warm-up period of 30 minutes,
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
Keysight Technologies U2300A Series USB Modular Multifunction Data Acquisition Devices. Data Sheet
Keysight Technologies U2300A Series USB Modular Multifunction Data Acquisition Devices Data Sheet Introduction The Keysight Technologies, Inc. U2300A Series USB modular multifunction data-acquisition (DAQ)
Octal, 16-Bit DAC with 5 ppm/ C On-Chip Reference in 14-Lead TSSOP AD5668-EP
Data Sheet Octal, -Bit with 5 ppm/ C On-Chip Reference in -Lead TSSOP FEATURES Enhanced product features Supports defense and aerospace applications (AQEC) Military temperature range ( 55 C to +5 C) Controlled
No missing codes guaranteed Refer to the AI Absolute Accuracy section. Sample rate
DEVICE SPECIFICATIONS NI 6378 PXI Express, 3.5 MS/s/ch, 16 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6378, refer to the
NI PXIe-5667 (3.6 GHz)
DEVICE SPECIFICATIONS NI PXIe-5667 (3.6 GHz) Spectrum Monitoring Receiver This document lists specifications for the NI PXIe-5667 (3.6 GHz) (NI 5667 (3.6 GHz)). The NI 5667 (3.6 GHz) radio frequency (RF)
16 AI Differential/32 AI Single-Ended, ±200 mv to ±10 V, 16 Bit, 250 ks/s Aggregate, Fuel-Cell Measurements. NI 9206 NI 9206 Getting Started Guide
DATASHEET NI 9206 16 AI Differential/32 AI Single-Ended, ±200 mv to ±10 V, 16 Bit, 250 ks/s Aggregate, Fuel-Cell Measurements Spring-terminal connectivity Protective backshell 600 VDC (US)/400 VDC (EU),
5520A. Multi-Product Calibrator. Extended Specifications
5520A Multi-Product Calibrator Extended Specifications Specifications The following tables list the 5520A specifications. All specifications are valid after allowing a warm-up period of 30 minutes, or
FP-SG-140 AND CFP-SG-140
FieldPoint Operating Instructions FP-SG-140 AND CFP-SG-140 Eight-Channel Strain-Gauge Input Modules These operating instructions describe how to install and use the FP-SG-140 and cfp-sg-140 strain-gauge
NI 9205 DATASHEET. 16 AI Differential/32 AI Single-Ended, ±200 mv to ±10 V, 16 Bit, 250 ks/s Aggregate
DATASHEET NI 9205 16 AI Differential/32 AI Single-Ended, ±200 mv to ±10 V, 16 Bit, 250 ks/s Aggregate DSUB or spring-terminal connectivity 250 Vrms, CAT II, channel-to-earth isolation (spring terminal);
PXIe Contents SPECIFICATIONS. ±60 V, 3 A Precision System PXI Source Measure Unit. These specifications apply to the PXIe-4139.
SPECIFICATIONS PXIe-4139 ±60 V, 3 A Precision System PXI Source Measure Unit These specifications apply to the PXIe-4139. Contents Definitions...2 Conditions... 2 Cleaning Statement... 2 Device Capabilities...
Bus-Powered M Series Multifunction DAQ for USB - 16-Bit, up to 400 ks/s, up to 32 Analog Inputs, Isolation
Technical Sales United States (866) 531-6285 info@ni.com Print E-mail this Page Open Document as PDF Requirements and Compatibility Ordering Information Detailed Specifications Pinouts/Front Panel Connections
Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
PXIe Contents SPECIFICATIONS. 1.5 GHz, 5 GS/s, 10-Bit PXI Express Oscilloscope
SPECIFICATIONS PXIe-5162 1.5 GHz, 5 GS/s, 10-Bit PXI Express Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...4 Accuracy...
PXI Contents SPECIFICATIONS. 24-Bit, Flexible Resolution PXI Oscilloscope
SPECIFICATIONS PXI-5922 24-Bit, Flexible Resolution PXI Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 2 Analog Input... 2 Impedance and Coupling... 2 Voltage Levels...3 Accuracy...
R&S ZNC Vector Network Analyzer Specifications
ZNC3_dat-sw_en_5214-5610-22_v0300_cover.indd 1 Data Sheet 03.00 Test & Measurement R&S ZNC Vector Network Analyzer Specifications 04.09.2012 13:39:47 CONTENTS Definitions... 3 Measurement range... 4 Measurement
Low Noise Variable Gain Low Frequency Voltage Amplifier
Measurement Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled,
Ethernet-Based Temperature, Voltage and Strain Measurement Modules
Ethernet-Based Temperature, Voltage and Strain Measurement Modules OMB-NET6000 Series OMB-NET6220 shown smaller than actual size. U 12 Analog Inputs U 8 Digital I/O U Simultaneous Sampling U Multiple Trigger
OPERATING INSTRUCTIONS NI Port, Low-Speed/Fault Tolerant CAN Module
OPERATING INSTRUCTIONS NI 9861 1-Port, Low-Speed/Fault Tolerant CAN Module These operating instructions describe how to use the National Instruments (NI) 9861 module. For information about installing,
LF411JAN Low Offset, Low Drift JFET Input Operational Amplifier
LF411JAN Low Offset, Low Drift JFET Input Operational Amplifier General Description This device is a low cost, high speed, JFET input operational amplifier with very low input offset voltage and guaranteed
N acquisitions, all channels simultaneously, N is selectable from 4, 16, 64, and 128 Inputs
With compliments All specifications apply to the TDS 200-Series Digital Real-Time Oscilloscope with a P2100 probe with the Attenuation switch set to 10X unless noted otherwise. To meet specifications,
USB Dynamic Signal Acquisition
NI USB-9233 24-bit resolution 102 db dynamic range 50 ks/s max rate per channel 4 simultaneous analog inputs ±5 V input range AC coupled with IEPE power Hi-Speed USB 2.0 Recommended Software LabVIEW LabVIEW
FP-RTD-124 AND CFP-RTD-124. Features. FieldPoint Operating Instructions. Eight-Channel Four-Wire RTD and Resistance Input Modules
FieldPoint Operating Instructions FP-RTD-124 AND CFP-RTD-124 Eight-Channel Four-Wire RTD and Resistance Input Modules These operating instructions describe how to install and use the National Instruments
PCI Contents SPECIFICATIONS. 24-Bit, Flexible Resolution PCI Oscilloscope Device
SPECIFICATIONS PCI-5922 24-Bit, Flexible Resolution PCI Oscilloscope Device Contents Definitions...2 Conditions... 2 Vertical... 2 Analog Input... 2 Impedance and Coupling... 2 Voltage Levels...3 Accuracy...
Dual, 16-Bit nanodac+ with 4 ppm/ C Reference, SPI Interface AD5689R-EP
Dual, 6-Bit nanodac+ with 4 ppm/ C Reference, SPI Interface FEATURES High relative accuracy (INL): ±4 LSB maximum at 6 bits Low drift.5 V reference: 4 ppm/ C typical Tiny package: 3 mm 3 mm, 6-lead LFCSP
High Resolution, Zero-Drift Current Shunt Monitor AD8217
High Resolution, Zero-Drift Current Shunt Monitor AD8217 FEATURES High common-mode voltage range 4.5 V to 8 V operating V to 85 V survival Buffered output voltage Wide operating temperature range: 4 C