PXI Modules 3066 PXI Multi-Way Active RF Combiner Data Sheet
|
|
- Priscilla Golden
- 5 years ago
- Views:
Transcription
1 PXI Modules 3066 PXI Multi-Way Active RF Combiner Data Sheet The most important thing we build is trust 250 MHz to 6 GHz RF signal conditioning module for multi- UE, MIMO and Smartphone testing Four full duplex DUT test interfaces and INPUT / OUTPUT interfaces to a signal analyzer and signal generator Independent multi stage gain settings for all forward and reverse paths RF output fine level control to each DUT test port High speed RF gain path switching (<100 μs) >60 db isolation between DUT test ports +34 dbm CW / +38 dbm Peak input power rating List Mode operation with PXI 3000 Series RF modules The PXI 3066 Multi-way Active RF Combiner is designed to help lower the cost of test in high volume manufacturing. When used in conjunction with PXI 3000 Series RF modular instruments and measurement software it enables simultaneous testing of up to 4 mobile communications devices in parallel using a single vector signal generator and a single vector signal analyzer. Figure 1. Simplified block diagram of PXI 3066
2 Figure 2. Parallel test of 4 transceivers PXI 3066 works on the principle that the efficiency of wireless device testing can be improved by maximizing the utilization of high value capital test assets. Improved test system efficiency is gained by sharing or multiplexing resources to avoid idle periods. During receiver testing PXI 3066 enables the output from a single vector signal generator (VSG) to be broadcast to or multiplexed between up to 4 full duplex DUT test interfaces. The output level at each DUT test port is independently adjustable. This ensures that the exact RF level can be set at the device under test input regardless of any variation in external losses. Receiver sensitivity measurements for multiple devices can therefore be performed concurrently saving test time. During transmitter testing PXI 3066 provides RF power combining or multiplexing between up to 4 full duplex DUT test ports and a single vector signal analyzer (VSA). Temperature and frequency compensated path loss data stored in the module may be queried and used to correct level measurements on all inputs. The total flexibility provided by this novel design can be utilized in a wide variety of test plan designs. In one example, 4 mobile UE transceivers can be synchronized to a common broadcast downlink. This then enables all devices to remain synchronized with the tester permitting their transmit outputs to be sequentially switched into the VSA, whilst in parallel executing receiver sensitivity measurements as shown in the figure 2. In cases where device under test control overheads represent the majority of test, this results in dramatic test time reductions. Another application for 3066 is to connect a single VSA / VSG to a device with multiple RF I/O ports such as smart phones. This eliminates complex external switching arrangements and reduces measurement uncertainty or the need for periodic system level calibration can also be used when testing devices with diversity or MIMO antenna connections such as used in cdma2000, LTE and WiFi. Configurable Paths RF INPUT to DUT 1 to 4 ports (source channels) PXI 3066 provides three coarse gain modes; Gain mode 0 (bypass), Gain mode 1 (low) and Gain mode 2 (high). In addition, each path can be isolated with the test port terminated into 50 Ω Fine level control is provided in each path to allow balancing of all path losses at the device under test input. Figure 3. Gain modes for each source channel 1 to 4
3 DUT 1 to 4 ports to RF OUTPUT (receive channels) PXI 3066 provides three coarse gain modes; Gain mode 0 (bypass), Gain mode 1 (low) and Gain mode 2 (high). In addition, each path can be isolated with the test port terminated into 50 Ω Temperature compensation data is stored within the module for each gain mode and for each receive channel. Figure 4. Path modes for each receive channel 1 to 4 High Port to Port Isolation PXI 3066 provides >60 db of isolation between DUT 1 to 4 ports to ensure mutual interference between test devices is avoided and >25 db of isolation between RF input and RF output ports, (below 3 GHz).
4 Compact Form Factor Figure typical port to port isolation PXI 3066 occupies 2 x 3U slot widths thus support highly compacted test systems to save production floor space and simplify test fixture design. Linearity 3rd order performance of the different gain modes has been carefully designed to work with and complement other PXI Digitizer and Signal Generator products. Calibration Data All calibration data for the module is stored internally and can be queried from the driver software. Triggering Path routing parameters can either be controlled directly from software or from hardware list memory addressing. A user pre-defined list of configurations can be stored in memory which is then recalled using a list controller. Each list entry contains the settings for each path between the DUT 1 to 4 test ports and the RF Input and RF output ports. List addresses can be routed to the module in parallel or serial form. Parallel or serial list addresses may be input from the PXI backplane trigger bus, or serial list addresses input via the front panel TRIG 1 & 2 connectors. The TRIG 1 & 2 connectors may also be configured as outputs, for example to route a serial list address to another module. Both the source and receiver channels have separate list memory areas so the path routing for each is setup independently. For example the source (downlink) may be slaved to a signal generator list controller, and the receiver (uplink) slaved to a RF digitizer list controller. Software The 3066 is supplied with a C /.net VXIpnp compatible driver with manual control supported in PXI Studio 2.
5 SPECIFICATION Specifications apply when used in conjunction with the driver software supplied with the module or a later version. All specifications apply when the module is used in a PXI standard compliant chassis and following a warm up period of 30 minutes. All figures assume operation in a 50Ω system unless stated, with all unused ports terminated in 50Ω. INTERFACE Definition of connection names:- Repeatability After warm up following a return from a change of operating mode valid for at least 2 hours and excluding temperature influence <±0.1 db FREQUENCY RESPONSE Typically <1 db across any 200 MHz bandwidth Typically <0.1 db across any 10 MHz bandwidth RETURN LOSS Port Return Loss (db) 3 GHz >3 GHz DUT 1-4 >20 >19, typ 20 RF IN/RF OUT >14 >10, typ 14 PORT TO PORT ISOLATION FREQUENCY RANGE 250 MHz to 6 GHz INSERTION LOSS RF INPUT to DUT 1 to 4 Ports (source channels) Operating modes: Gain mode 0, Gain mode 1, Gain mode 2 Insertion loss with Fine Level Control set to 0 db Loss (db) Gain mode 0 Gain Mode 1 Gain Mode 2 Maximum Minimum RF Input to DUT, Fine Level Control Range 0 db to -4 db with resolution 0.1 db Relative Level Error between DUT Ports ±0.25 db typical 1 Accuracy 2 (23 degrees ±5 degrees) Frequency (GHz) Accuaracy (±/db) Gain mode >3 0.7 Gain mode >3 0.5 Gain mode >3 0.7 DUT 1 to 4 Ports to RF OUTPUT (receive channels) (Un-used ports terminated into 50 ) RF INPUT to RF OUTPUT 3 3 GHz, >25 db, typ. 30 db >3 GHz, >20 db, typ. 25 db DUT-DUT 4 >60 db SWITCHING SPEED Settled to within 0.1 db of final path loss <100 us LINEARITY Source Path, RF Input DUT Output P1dB (1 db Compression Point). Gain offset set to 0 db Typical output power at 1 db gain compression point (dbm) 0 N/A 5 1 >-10 2 >2 Output IP3 (third order intercept point). Gain offset set to 0 db with 1 MHz or 10 MHz tone spacing Typical output power referred TOI (dbm) 0 N/A 1 >5 2 >15 Operating modes: Gain mode 0, Gain mode 1, Gain mode 2 Loss Gain mode 0 Gain mode 1 Gain mode 2 Maximum loss (db) Minimum loss (db) Both DUT ports in the same operating mode 2 The error in compensation data stored internal to the module 3 Applied when source gain mode set to 1 and receiver gain mode set to 2. Only 1 DUT port active 4 Applies when all active source paths set to same gain mode and all active receiver paths set to same gain mode. Only 1 DUT port active 5 Gain mode 0 has no active gain stages
6 Receive Path, DUT RF Output Input P1dB (1 db Compression Point 6 ) Operating mode Input IP3 7 (third order intercept point) with 1 MHz or 10 MHz tone spacing SOFTWARE C dll /.NET Provides the ability to set & query path routing, define hardware trigger control mapping, compensate path/system losses PXI Studio plug-in for soft front panel manual control GENERAL Inputs and Outputs Typical input power at 1dB gain compression point (dbm) 0 >38 1 >27 2 >14 Typical input referred TOI (dbm) 0 >45 1 >37 2 >37 Description Connector Coupling DC Impedance Max Power RF INPUT SMA (F) AC 16V dbm avg / CW Safety EN Safety requirements for electrical equipment for measurement, control and laboratory use-part 1, General requirements Rated Range of Use Operating Temperature 0 to 50 C, meets IEC :2007 and :2007 Operating Humidity 10 to 90% non-condensing, meets IEC :2001 Conditions of Storage and Transportation Storage Temperature -20 to +70 C, meets IEC :2007 and :2007 Storage Humidity 5 to 93% non-condensing, tested to IEC :2001 Shock 30 g peak, half sine, 9 ms pulse. Tested in accordance with IEC :2008 Random vibration 5 Hz to 500 Hz, 2.46 g rms non-operating. Tested in accordance with IEC :2008 Compliance PXI Specification, Revision 2.2, ECN 1 Revision 1.0 VXIplug&play Specifications (VPP-2, VPP-3.x, VPP-4.x and VPP-7) Minimum System Controller Requirements Recommended minimum memory 2 Gbyte Operating System, Windows XP, Windows 7 (32 bit) RF OUTPUT SMA (F) AC 16V 50 DUT 1-4 SMA (F) DC 0V dbm avg / CW (reverse power) 34 dbm avg / CW 38 dbm PEP TRIG I/O 1 and 2 SMB (F) High Z TTL Dimensions 2-slot wide x 3U PXI-Hybrid slot compatible module Weight 832 g Power Consumption (Typical) Dissipation: 30 W Current +3.3 V +5 V +12 V -12 V <4 A <4 A <1A <0.5 A Warranty Recommended calibration Interval 2 years 2 years Electromagnetic Compatibility EN Emissions Class A, Immunity Table 1 6 DUT RF Output paths share a common output amplifier. IP1dB values given are for a single active path 7 DUT RF Output paths share a common output amplifier. IP3 values given are for a single active path
7 VERSIONS, OPTIONS AND ACCESSORIES Ordering Numbers Description 3066 PXI RF Multi-Way Active RF Combiner Supplied with 43139/738 1 x SMA-SMA 130 mm link cable 43139/739 1 x SMA-SMA 180 mm link cable Accessories 43139/738 SMA-SMA RF link cable 130 mm 43139/739 SMA-SMA RF link cable 180 mm 43139/783 SMA-SMA RF link cable 240 mm 43139/859 SMB-SMB Link Cable Assembly 150 mm 46885/224 SMA connector saver SMA 50 ohm termination Service Options W3066/103 Standard Extended Warranty 36 months W3066/103C Standard Extended Warranty 36 months with scheduled calibration W3066/105 Standard Extended Warranty 60 months W3066/105C Standard Extended Warranty 60 months with scheduled calibration
8 Cobham Wireless - Validation Part No.46891/435, Issue 1, 03/16
PXI Modules 3070A PXI High Performance RF Digitizer Data Sheet
PXI Modules 3070A PXI High Performance RF Digitizer Data Sheet The most important thing we build is trust Continuous frequency range 250 MHz to 3 GHz or 6 GHz Input levels to +30 dbm with 1 db RF step
More information3066 PXI Multi-way Active RF Combiner 250 MHz 6 GHz. User Manual
3066 PXI Multi-way Active RF Combiner 250 MHz 6 GHz User Manual Document no. 47090/121 Issue 2 28 September 2015 PREFACE About this manual This manual explains how to set up and configure a Cobham 3066
More informationFull system level calibration (levels, s-parameters, noise) Full RF source and measure capability Applications Vector network analyzer capability
Semiconductor Test AXRF - Multi-Port PXI RF Subsystem Modulated Vector Source and Measurement Data Sheet The most important thing we build is trust Functionality High speed, reliable solid state design
More informationPreliminary. PXI PRELIMINARY 3041 Small Cell RF Tester Data Sheet. The most important thing we build is trust. Test up to 4 small cells in parallel
PXI PRELIMINARY 3041 Small Cell RF Tester Data Sheet The most important thing we build is trust Turnkey production ATE solution for testing Small Cell base stations Automated Tx and Rx RF alignment and
More informationNI PXIe-5601 Specifications
NI PXIe-5601 Specifications RF Downconverter This document lists specifications for the NI PXIe-5601 RF downconverter (NI 5601). Use the NI 5601 with the NI PXIe-5622 IF digitizer and the NI PXI-5652 RF
More informationPXI Modules. 3030A Wideband RF Digitizer.
PXI Modules 3030A Wideband RF Digitizer Fully featured wideband PXI RF Digitizer module for complex signal analysis applications in communications system test Frequency range 330 MHz to 3 GHz Wide 33 MHz
More informationPXI Modules Series RF Digitizers
PXI Modules 3030 Series RF Digitizers Fully featured wideband PXI RF digitizer module for complex signal analysis applications in communications system test Frequency ranges to 3 GHz or 6 GHz 36 MHz or
More informationPXI Modules PXI Digital RF Signal Generator.
PXI Modules 3020 PXI Digital RF Signal Generator Fully featured PXI Digital RF Signal Generator module for complex digital IQ waveform applications in communications system test Frequency range 250 MHz
More informationPreliminary. PXI Modules Wideband RF Digitizer.
PXI Modules 3035 Wideband RF Digitizer Frequency range 330 MHz to 6 GHz 36 MHz wide digitized bandwidth 14 bit A/D resolution with 103.68 MHz sample rate 75 db spurious free dynamic range 75 db intermodulation
More informationData Sheet SC5317 & SC5318A. 6 GHz to 26.5 GHz RF Downconverter SignalCore, Inc. All Rights Reserved
Data Sheet SC5317 & SC5318A 6 GHz to 26.5 GHz RF Downconverter www.signalcore.com 2018 SignalCore, Inc. All Rights Reserved Definition of Terms 1 Table of Contents 1. Definition of Terms... 2 2. Description...
More informationFlexible and Modular Approaches to Multi-Device Testing
Flexible and Modular Approaches to Multi-Device Testing by Robin Irwin Aeroflex Test Solutions Introduction Testing time is a significant factor in the overall production time for mobile terminal devices,
More informationReflectometer Series:
Reflectometer Series: R54, R60 & R140 Vector Network Analyzers Clarke & Severn Electronics Ph +612 9482 1944 Email sales@clarke.com.au BUY NOW - www.cseonline.com.au KEY FEATURES Patent: US 9,291,657 No
More informationIQgig-IF TM Technical Specifications
TECHNICAL SPECIFICATIONS IQgig-IF TM Technical Specifications 2018 LitePoint, A Teradyne Company. All rights reserved. Port Descriptions IQgig-IF Front Panel I/O Function Type Power Switch Power On/Off
More informationPXI Maestro PXI Maestro, software that accelerates wireless device test speed and reduces ATE system development time.
PXI Maestro PXI Maestro, software that accelerates wireless device test speed and reduces ATE system development time. Highlights End-to-end ATE for multi-up non signalling RF test Supports single or dual
More informationR&S ZVT Vector Network Analyzer Specifications
R&S ZVT Vector Network Analyzer Specifications Test & Measurement Data Sheet 08.00 CONTENTS Definitions... 3 Specifications... 4 Measurement range...4 Measurement speed...5 Measurement accuracy...6 Effective
More informationPXI Timing and Synchronization Control
NI PXI-665x Works with all PXI modules Multichassis PXI synchronization Onboard routing of internal or external clock and trigger signals PXI slot 2 star trigger controller Onboard high-stability references
More information2.5 GHz 75 Ω Multiplexer and SPDT Relay Switches
2.5 GHz Multiplexer and SPDT Relay Switches NI PXI-255x NEW! 2.5 GHz bandwidth characteristic impedance 30 V max switching voltage 0.5 A max switching current 10 W max switching power Mini SMB direct connectivity
More informationIQcell TM Technical Specifications
TECHNICAL SPECIFICATIONS IQcell TM Technical Specifications 2017 LitePoint, A Teradyne Company. All rights reserved. IQcell is a highly-integrated, manufacturing optimized, multi-dut signaling test set,
More informationPXI Modules Series RF Digitizers
PXI Modules 3030 Series RF Digitizers Fully featured wideband PXI RF digitizer module for complex signal analysis applications in communications system test Frequency ranges to 3 GHz or 6 GHz Choose from
More informationModel 865 RF / Ultra Low Noise Microwave Signal Generator
Model 865 RF / Ultra Low Noise Microwave Signal Generator Features Excellent signal purity: ultra-low phase noise and low spurious Combination of highest output power and fastest switching Powerful touch-display
More informationPXI Modules PXI RF Digitizer.
PXI Modules 3030 PXI RF Digitizer Fully featured PXI RF Digitizer module for complex signal analysis applications in communications system test Frequency range 330 MHz to 3 GHz Wide 20 MHz digitized corrected
More informationContents. ZT530PCI & PXI Specifications. Arbitrary Waveform Generator. 16-bit, 400 MS/s, 2 Ch
ZT530PCI & PXI Specifications Arbitrary Waveform Generator 16-bit, 400 MS/s, 2 Ch Contents Outputs... 2 Digital-to-Analog Converter (DAC)... 3 Internal DAC Clock... 3 Spectral Purity... 3 External DAC
More informationPXI Modules 3020 Series Digital RF Signal Generators Data Sheet
PXI Modules 3020 Series Digital RF Signal Generators Data Sheet The most important thing we build is trust Frequency ranges spanning 100 khz to 6 GHz Level ranges -120 dbm up to +17 dbm max. Level accuracy
More informationKeysight Technologies PXI Programmable Step Attenuator Module
Keysight Technologies PXI Programmable Step Attenuator Module M9168C DC to 26.5 GHz M9168E DC to 50 GHz Data Sheet Introduction Keysight Technologies, Inc. has been a leading designer and manufacturer
More informationSpectrum Analyzer R&S FS300
Spectrum Analyzer R&S FS300 9 khz to 3 GHz The new product family from Rohde & Schwarz Professional test equipment for laboratory, service and production The R&S FS300 is a highly accurate spectrum analyzer
More informationKeysight Technologies P9400A/C Solid State PIN Diode Transfer Switches
Keysight Technologies P9400A/C Solid State PIN Diode Transfer Switches P9400A 100 MHz to 8 GHz PIN transfer switch P9400C 100 MHz to 18 GHz PIN transfer switch Technical Overview Key Features Minimize
More information2026Q CDMA/GSM Interferer MultiSource Generator
Signal Sources 2026Q CDMA/GSM Interferer MultiSource Generator The 2026Q is designed to work with a radio test set to provide a fully integrated radio receiver test solution for cellular and PCS systems
More informationPXIe Contents SPECIFICATIONS. 14 GHz and 26.5 GHz Vector Signal Analyzer
SPECIFICATIONS PXIe-5668 14 GHz and 26.5 GHz Vector Signal Analyzer These specifications apply to the PXIe-5668 (14 GHz) Vector Signal Analyzer and the PXIe-5668 (26.5 GHz) Vector Signal Analyzer with
More informationRacal Instruments. Product Information
Racal Instruments 6084A-104-DMM 1 GHz Digitizer and 7.5 Digit Digital Multimeter The Digitizer/DMM increases test system performance and density by packaging a 7.5 digit Digital Multimeter (DMM) together
More informationPLANAR R54. Vector Reflectometer KEY FEATURES
PLANAR R54 Vector Reflectometer KEY FEATURES Frequency range: 85 MHz 5.4 GHz Reflection coefficient magnitude and phase, cable loss, DTF Transmission coefficient magnitude when using two reflectometers
More informationNI PXI-2555 Specifications
NI PXI-2555 Specifications 2.5 GHz Terminated 4 x 1 Multiplexer (SP4T) This document lists specifications for the NI PXI-2555 multiplexer module. All specifications are subject to change without notice.
More informationAgilent U9397A/C FET Solid State Switches (SPDT)
Agilent U9397A/C FET Solid State Switches (SPDT) U9397A 300 khz to 8 GHz U9397C 300 khz to 18 GHz Technical Overview Key Features Prevent damage to sensitive components with low video leakage < 10 mvpp
More informationExtending test capabilities of the PXI 3000 RF test solution with 3060 Series RF combiner modules
Application Note Extending test capabilities of the PXI 3000 RF test solution with 3060 Series RF combiner modules The purpose of this application note is to present the use of the 3060 Series PXI RF combiners
More informationNI PXIe-5630 Specifications
NI PXIe-5630 Specifications RF Vector Network Analyzer This document lists specifications for the NI PXIe-5630 RF vector network analyzer (NI 5630). Specifications are warranted under the following conditions:
More informationSpectrum Analyzers 2680 Series Features & benefits
Data Sheet Features & benefits n Frequency range: 9 khz to 2.1 or 3.2 GHz n High Sensitivity -161 dbm/hz displayed average noise level (DANL) n Low phase noise of -98 dbc/hz @ 10 khz offset n Low level
More informationR&S ZNC Vector Network Analyzer Specifications
ZNC3_dat-sw_en_5214-5610-22_v0300_cover.indd 1 Data Sheet 03.00 Test & Measurement R&S ZNC Vector Network Analyzer Specifications 04.09.2012 13:39:47 CONTENTS Definitions... 3 Measurement range... 4 Measurement
More informationReconfigurable 6 GHz Vector Signal Transceiver with I/Q Interface
SPECIFICATIONS PXIe-5645 Reconfigurable 6 GHz Vector Signal Transceiver with I/Q Interface Contents Definitions...2 Conditions... 3 Frequency...4 Frequency Settling Time... 4 Internal Frequency Reference...
More informationSC5307A/SC5308A 100 khz to 6 GHz RF Downconverter. Datasheet SignalCore, Inc.
SC5307A/SC5308A 100 khz to 6 GHz RF Downconverter Datasheet 2017 SignalCore, Inc. support@signalcore.com P RODUCT S PECIFICATIONS Definition of Terms The following terms are used throughout this datasheet
More informationVector Network Analyzers ZVB
Specifications Version 05.00 Vector Network Analyzers ZVB September 2005 Specifications MEASUREMENT RANGE...3 MEASUREMENT SPEED...5 MEASUREMENT ACCURACY...6 EFFECTIVE SYSTEM DATA...8 TEST PORT OUTPUT...8
More informationPXI LTE/LTE-A Downlink (FDD and TDD) Measurement Suite Data Sheet
PXI LTE/LTE-A Downlink (FDD and TDD) Measurement Suite Data Sheet The most important thing we build is trust Designed for the production test of the base station RF, tailored for the evolving small cell
More informationSC5407A/SC5408A 100 khz to 6 GHz RF Upconverter. Datasheet. Rev SignalCore, Inc.
SC5407A/SC5408A 100 khz to 6 GHz RF Upconverter Datasheet Rev 1.2 2017 SignalCore, Inc. support@signalcore.com P R O D U C T S P E C I F I C A T I O N S Definition of Terms The following terms are used
More informationLB679A CW and Pulse (Modulation) USB PowerSensor+ Data Sheet
Key PowerSensor+ Specifications 50 MHz to 20 GHz - 40 dbm to +20 dbm 2.8% Total Error* 1.20:1 VSWR (-21 db Return Loss) * Measuring a well matched DUT (-20 dbm @ 2 GHz) Key PowerSensor+ Capability Test
More informationM5090. Extended Specifications EXTEND YOUR REACH TM
M5090 Extended Specifications TM Frequency range: 300 khz - 8.5 GHz Wide output power adjustment range: -55 dbm to +5 dbm Dynamic range: 130 db (10 Hz IF bandwidth) typ. Measurement time per point: 70
More informationData Sheet. Agilent M9185A PXI Isolated D/A Converter. DISCOVER the Alternatives... Agilent MODULAR Products. 8/16-Channel 16-bit, ±16 V
Agilent M9185A PXI Isolated D/A Converter Data Sheet 8/16-Channel 16-bit, ±16 V DISCOVER the Alternatives...... Agilent MODULAR Products Overview Introduction The Agilent M9185A is a digital/analog converter
More informationPXI UMTS Uplink Measurement Suite Data Sheet
PXI UMTS Uplink Measurement Suite Data Sheet The most important thing we build is trust A production ready ATE solution for RF alignment and performance verification Tx Max Output Power Frequency Error
More informationRF Semiconductor Test AXRF-Q Multi-Port PXI RF Sub-System
RF Semiconductor Test AXRF-Q Multi-Port PXI RF Sub-System Datasheet The most important thing we build is trust Overview AXRF-Q Multi-Port PXIe RF Subsystem is an integrated solution for testing RF semi-conductor
More informationNI PXIe-5663 Specifications
NI PXIe-5663 Specifications 6.6 GHz RF Vector Signal Analyzer with Digital Downconversion This document lists specifications for the NI PXIe-5663 RF vector signal analyzer (NI 5663). The NI 5663 comprises
More informationR&S ZVT Vector Network Analyzer Specifications
ZVT_dat-sw_en_0758-065-22_v0900_cover.indd Data Sheet 09.00 Test & Measurement R&S ZVT Vector Network Analyzer Specifications 06.03.205 5:50:4 CONTENTS Definitions... 3 Specifications... 4 Measurement
More informationNI PXI/PXIe Contents. About These Specifications DEVICE SPECIFICATIONS. Quad 2 1 Terminated Multiplexer
DEVICE SPECIFICATIONS NI PXI/PXIe-2542 Quad 2 1 Terminated Multiplexer This document lists specifications for the NI PXI/PXIe-2542 (NI 2542) multiplexer module. All specifications are subject to change
More informationPXI LTE FDD and LTE TDD Measurement Suites Data Sheet
PXI LTE FDD and LTE TDD Measurement Suites Data Sheet The most important thing we build is trust A production ready ATE solution for RF alignment and performance verification UE Tx output power Transmit
More informationIQgig-RF TM Model B Technical Specifications
TECHNICAL SPECIFICATIONS IQgig-RF TM Model B Technical Specifications 2018 LitePoint, A Teradyne Company. All rights reserved. Port Descriptions IQgig-RF Test Controller Front Panel I/O Function Type Power
More informationDSA700 Series Spectrum Analyzer
DSA700 Series Spectrum Analyzer Product Features: All-Digital IF Technology Frequency Range from 100 khz up to 1 GHz Min. -155 dbm Displayed Average Noise Level (Typ.) Min.
More informationNI PXI-2557 Specifications
NI PXI-2557 Specifications 2.5 GHz 75 8 x 1 Multiplexer (SP8T) This document lists specifications for the NI PXI-2557 multiplexer module. All specifications are subject to change without notice. Visit
More informationBecker Nachrichtentechnik GmbH Kapellenweg Asbach - Germany
High Dynamic 8 Way Combiner 100 khz... 4000 MHz, 50 Ω Features - wideband - high dynamic - without signal losses - low power consumption - high port- to- port isolation - compact 19, 1 U design Applications
More information1-Port USB VNA - R60 Extended Specifications
TM 1- USB VNA - R60 Extended Specifications Patent US 9,291,657 - No test cable needed Frequency range: 1 MHz - 6 GHz Measurement time per point: 100 µs min typ. Automation programming in LabView, Python,
More information2302 Battery Simulator 2306, 2306-PJ Battery/Charger Simulators
Ultrafast response to transient load currents Choice of single- or dualchannel supplies Optimized for development and testing of battery-powered devices Variable output resistance for simulating battery
More informationLitePoint IQxstream-M
TECHNICAL SPECIFICATIONS LitePoint IQxstream-M 2017 LitePoint, A Teradyne Company. All rights reserved. IQxstream-M is a manufacturing-oriented, multi-device, physical layer communication system tester,
More informationIQgig-RF TM Technical Specifications
TECHNICAL SPECIFICATIONS IQgig-RF TM Technical Specifications 2017 LitePoint, A Teradyne Company. All rights reserved. IQgig-RF is a scalable physical-layer test solution, tailored for 802.11ad (WiGig)
More informationCompact Series: S5065 & S5085 Vector Network Analyzers KEY FEATURES
Compact Series: S5065 & S5085 Vector Network Analyzers KEY FEATURES Frequency range: 9 khz - 6.5 or 8.5 GHz Measured parameters: S11, S12, S21, S22 Wide output power adjustment range: -50 dbm to +5 dbm
More informationTECHNICAL SPECIFICATIONS. LitePoint IQxstream LitePoint, A Teradyne Company. All rights reserved.
TECHNICAL SPECIFICATIONS LitePoint IQxstream 2017 LitePoint, A Teradyne Company. All rights reserved. IQxstream is a manufacturing oriented, physical layer communication system tester, tailored to verifying
More informationMain Features: ERZ-LNA Typical applications: Performance
Main Features: Frequency Range: 2 to 45 GHz. Typical values: Gain 15 db, NF 5 db RF connectors (I/O): 2.4 mm Solder filtered pins for DC connection Several mounting options Gold platted compact aluminum
More informationLB480A Pulse Profiling USB PowerSensor+ Data Sheet
Key PowerSensor+ Specifications 100 MHz to 8 GHz (functional to 10 GHz) -60 dbm to +20 dbm 1.95% Total Error* 1.09:1 VSWR (-27 db Return Loss) * Measuring a well matched DUT (-20 dbm @ 1 GHz) Measurement
More informationCompact VNA - TR7530. Extended Specifications EXTEND YOUR REACH TM
Compact VNA - TR7530 TM Extended Specifications Frequency range: 20 khz - 3 GHz Wide output power adjustment range: -50 dbm to +5 dbm Dynamic range: 123 db (10 Hz IF bandwidth) typ. Measurement time per
More informationCobalt Series 20 GHz EXTEND YOUR REACH TM
Cobalt Series 20 GHz TM Frequency range: 100 khz - 20 GHz Wide output power range: -60 dbm to +10 dbm Dynamic range: 135 db (10 Hz IF bandwidth) typ. Measurement time per point: 10 µs per point, min typ.
More informationSC5306B 1 MHz to 3.9 GHz RF Downconverter Core Module. Datasheet SignalCore, Inc.
SC5306B 1 MHz to 3.9 GHz RF Downconverter Core Module Datasheet 2015 SignalCore, Inc. support@signalcore.com SC5306B S PECIFICATIONS Definition of Terms The following terms are used throughout this datasheet
More informationHMC-T2220B. Portable & Battery Operated! Portable Synthesized Signal Generator, 10 MHz to 20 GHz. Instrumentation Product Support at
Portable, 10 MHz to 20 GHz Portable & Battery Operated! 78-250-3343 tel 78-250-3373 fax Battery Operated 20 GHz Signal Generator! The is a battery powered, portable test equipment solution designed to
More informationPXI. cdma2000/ev-do Measurement Suite Data Sheet. The most important thing we build is trust. cdma2000 RC1 to RC4 reverse link analysis
PXI cdma2000/ev-do Measurement Suite Data Sheet The most important thing we build is trust cdma2000 RC1 to RC4 reverse link analysis 1xEV-DO rev 0, rev A and rev B (No Feedback Multiplexing mode) reverse
More informationR3477. Ideal for mobile communication applications including base stations and handsets, from the development stage to production and installation
R3477 Signal Analyzers Ideal for mobile communication applications including base stations and handsets, from the development stage to production and installation Frequency range: 9 khz to 13.5 GHz World
More informationRF & Microwave Test Solutions from Pickering Interfaces
RF & Microwave Test Solutions from Pickering Interfaces Pickering Interfaces has a wide range of RF & Microwave switch modules that can be used to increase the fl exibility of Test & Measurement systems
More informationContents. CALIBRATION PROCEDURE NI PXIe-5668R 14 GHz and 26.5 GHz Signal Analyzer
CALIBRATION PROCEDURE NI PXIe-5668R 14 GHz and 26.5 GHz Signal Analyzer This document contains the verification procedures for the National Instruments PXIe-5668R (NI 5668R) vector signal analyzer (VSA)
More informationPXI MICROWAVE LOCAL OSCILLATOR MODULE
The PXI-1450B Local Oscillator Module is a PXI 3U, 2-slot synthesizer module intended for frequency down conversion applications. The PXI-1450B is a VCO-based, 3 to 9 GHz synthesizer that uses QuickSyn
More informationMA24104A. Inline High Power Sensor. True-RMS, 600 MHz to 4 GHz
Product Brochure MA24104A Inline High Power Sensor True-RMS, 600 MHz to 4 GHz A Standalone, Compact, and Highly Accurate Inline High Power Sensor for your RF Power Measurement Needs MA24104A at a Glance
More informationNI PXI-4461 Specifications
NI PXI-446 Specifications Analog Input Input Characteristics This document lists specifications for the NI PXI-446 Dynamic Signal Acquisition (DSA) device. These specifications are typical at 5 C unless
More informationHMC-T2240. Synthesized Signal Generator, 10 MHz to 40 GHz
Synthesized Signal Generator, 10 MHz to 40 GHz , 10 MHz to 40 GHz Wide Range, 10 MHz to 40 GHz Signal Generator! The is an easy to implement test equipment solution designed to fulfill your signal generation
More informationR&S ZV-Z5x Calibration Units Specifications
R&S ZV-Z5x Calibration Units Specifications Test & Measurement Data Sheet 10.00 Specifications apply under the following conditions: Sufficient warm-up time (approx. 15 minutes) at ambient temperature,
More informationR&S ZNBT8 Vector Network Analyzer Specifications
E stablished 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) ZNBT8_dat-sw_en_3606-9727-22_v0200_cover.indd 1 Data Sheet 02.00 Test & Measurement R&S ZNBT8 Vector Network Analyzer
More informationz8801 Local Oscillator PXI
TECHNICAL SPECIFICATIONS z8801 Local Oscillator PXI 2014 LitePoint, A Teradyne Company. All rights reserved. Port Descriptions Front Panel Label Type Description REF OUT SMA Backplane reference clock output
More informationR&S SMB100N SIGNAL GENERATOR
R&S SMB100N SIGNAL GENERATOR PERFORMANCE SPECIFICATIONS VERSION 02.00, SEPTEMBER 2009 CONTENTS Specifications...3 Definitions... 3 RF performance... 4 Frequency... 4 Frequency sweep... 4 Reference frequency...
More informationR&S EB500 Monitoring Receiver Specifications
Radiomonitoring & Radiolocation Data Sheet 01.02 R&S EB500 Monitoring Receiver Specifications CONTENTS Definitions... 3 Specifications... 4 Frequency...4 Linearity...4 Interference rejection...4 Noise
More informationImpedance 50 (75 connectors via adapters)
VECTOR NETWORK ANALYZER PLANAR 304/1 DATA SHEET Frequency range: 300 khz to 3.2 GHz Measured parameters: S11, S21, S12, S22 Dynamic range of transmission measurement magnitude: 135 db Measurement time
More informationHILNA LS Low Noise Amplifier
HILNA LS Low Noise Amplifier 1000-3000 MHz 50 db Gain P/N: HILNA-LS (includes NW-LN-ACC-CB4MUA interface cable) NuWaves HILNA LS is a broadband low noise amplifier covering L- & S-bands, and designed to
More informationLB480A Pulse Profiling USB PowerSensor+ Data Sheet
Key PowerSensor+ Specifications 50 MHz to 8 GHz (functional to 10 GHz) - 60 dbm to +20 dbm 1.95% Total Error* 1.09:1 VSWR (-27 db Return Loss) * Measuring a well matched DUT (-20 dbm @ 1 GHz) No Zero No
More informationFrequency range 100 khz to 3 GHz 100 khz to 6 GHz 10 MHz to 18 GHz Reference frequency. 2 ppm in addition 2 ppm/10 C. 0 Hz, 100 Hz to 3 GHz
Specifications Specifications apply under the following conditions: 15 minutes warm-up time at ambient temperature, specified environmental conditions met, and calibration cycle adhered to. Data without
More informationMulti-Port RF Subsystem. PXI Compatible Vector Source & Measurement System
Multi-Port RF Subsystem PXI Compatible Vector Source & Measurement System RF Functionality Parallel Measurement Support Full Source and Measure Capability Vector Network nalyzer Capability Full Modulation
More informationNote Using the PXIe-5785 in a manner not described in this document might impair the protection the PXIe-5785 provides.
SPECIFICATIONS PXIe-5785 PXI FlexRIO IF Transceiver This document lists the specifications for the PXIe-5785. Specifications are subject to change without notice. For the most recent device specifications,
More informationPXIe, 24-Channel, ±24 V, 50 ma Precision PXI Source Measure Unit
SPECIFICATIONS PXIe-4163 PXIe, 24-Channel, ±24 V, 50 ma Precision PXI Source Measure Unit Contents Definitions...1 Conditions... 2 Instrument Capabilities... 2 SMU Specifications... 3 Voltage...3 Current...
More informationR&S ZV-Z5x Calibration Units Specifications
R&S ZV-Z5x Calibration Units Specifications Test & Measurement Data Sheet 09.01 Specifications apply under the following conditions: Sufficient warm-up time (approx. 15 minutes) at ambient temperature,
More informationReconfigurable 6 GHz RF Vector Signal Transceiver with 1 GHz Bandwidth
CALIBRATION PROCEDURE PXIe-5840 Reconfigurable 6 GHz RF Vector Signal Transceiver with 1 GHz Bandwidth This document contains the verification procedures for the PXIe-5840 vector signal transceiver. Refer
More informationR&S ZNB Vector Network Analyzer Specifications
Umschlag_ZNB4-8_dat-sw_en_5214-5384-22.indd 1 Data Sheet 02.00 Test & Measurement R&S ZNB Vector Network Analyzer Specifications 07.11.2011 10:03:35 CONTENTS Definitions... 3 Measurement range... 4 Measurement
More informationNI PXI-2530 Specifications
NI PXI-2530 Specifications 128-Channel Reed Relay Multiplexer/Matrix This document lists specifications for the National Instruments PXI-2530 128-channel multiplexer/matrix module. All specifications are
More informationSignal Sources. 2026Q CDMA Interferer Multisource Generator. Advanced Test Equipment Rentals ATEC (2832)
Signal Sources Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) 2026Q CDMA Interferer Multisource Generator The 2026Q is designed to work with a radio test set to provide
More informationLB680A Pulse Profiling USB PowerSensor+ Data Sheet
Key PowerSensor+ Specifications 50 MHz to 20 GHz - 40 dbm to +20 dbm 2.8% Total Error* 1.20:1 VSWR (-21 db Return Loss) * Measuring a well matched DUT (-20 dbm @ 2 GHz) Measurement Capability Time Gated
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK Synthesized Signal Generator, 10
More informationIQxel TM Next Generation Connectivity Test System
TECHNICAL SPECIFICATIONS IQxel TM Next Generation Connectivity Test System 2017 LitePoint, A Teradyne Company. All rights reserved. General Technical Specifications RF Analyzer Parameter Ports Value Input
More informationNI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer
NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer This document lists specifications for the NI PXI-2797 terminated multiplexer module. All specifications are subject to change without
More informationNI PXI/PXIe-2541 Specifications 300 MHz Ω Matrix
NI PXI/PXIe-2541 Specifications 3 MHz 8 12 5 Ω Matrix This document lists specifications for the NI PXI/PXIe-2541 (NI 2541) matrix module. All specifications are subject to change without notice. Visit
More information3250 Series Spectrum Analyzer
The most important thing we build is trust ADVANCED ELECTRONIC SOLUTIONS AVIATION SERVICES COMMUNICATIONS AND CONNECTIVITY MISSION SYSTEMS 3250 Series Spectrum Analyzer > Agenda Introduction
More informationHigh-speed programmable attenuator MAT800
High-speed programmable attenuator MAT800 Windows98/Me/2000/XP/Vista/7(32bit) correspondence GP-IB, RS-232C and software for making attenuation program are standard accessories. Optimum for evaluation
More informationKeysight Technologies 87405C 100 MHz to 18 GHz Preamplifier. Technical Overview
Keysight Technologies 8745C 1 MHz to 18 GHz Preamplifier Technical Overview 2 Keysight 8745C 1 MHz to 18 GHz Preamplifier Technical Overview Introduction The Keysight Technologies, Inc. 8745C preamplifier
More informationPXI. TD-SCDMA Measurement Suite Data Sheet. The most important thing we build is trust. Total Average Power plus Midamble / Data Power
PXI TD-SCDMA Measurement Suite Data Sheet The most important thing we build is trust Total Average Power plus Midamble / Data Power Transmit On/Off Time Mask Transmit Closed Loop Power Control (CLPC) Spectrum
More information