Model Vortex PhD General Specification

Transcription

1 Model General Specification Features! Reliableno moving parts, no fluid to sensor contact! In-process removable sensor, below 750 psig (52 barg) pressure! Simple, rugged, all welded construction, no internal gaskets, no leak paths! High accuracy with wide rangeability! Line sizes from 1" to 12" ( mm )! High temperature operation up to 750 F (400 C)! EZ Logic menu-driven user interface! Smart electronics provide excellent noise immunity! Compatible with HART Protocol! Optional Dual sensors and transmitters for fail-safe monitoring The EMCO vortex shedding flowmeter measures process fluid flow by detecting the frequency at which vortices are shed from an obstruction in the process fl uid line (the bluff body). A piezo-electric sensor mounted outside the fl ow line acts as the transducer, converting vortex pulses into electrical signals. The Smart electronics provide excellent noise immunity while the wide range of wetted materials provide outstanding compatibility with most process fl uids. The transmitter provides a frequency output, scaled frequency output, totalizer pulse or a 4-20 ma DC signal proportional to the fl ow rate. (303) Fax (303) sales@emcoflow.com

2 Performance Specifications Accuracy Liquid... ± 0.7% of fl ow rate Gas and Steam... ± 1.0% of fl ow rate Analog Output Version... Add ± 0.1% of full scale Repeatability ± 0.15% of fl ow rate Operating Specifications Fluid Types Liquid, gas or steam Line Sizes 1" 12" ( 25mm to 300mm ) Process Temperature Limit 40 to 750 F ( 40 to 400 C ) Process Pressure Flange ANSI Class 150, 300 or 600, PN16, 40, 64 Wafer All wafer bodies are rated based on appropriate fl ange rating to a maximum of ANSI Class 600 Enclosure Specifications Approved for NEMA 4X watertight and dust tight requirements. Ambient Temperature Limit Normal 20 to 140 F ( 29 to 60 C) Display Option F (0 60 C) AMBIENT TEMPERATURE F ( C) 180 (82) 150 (66) 140 (60) 110 (43) 70 (22) Response Time Adjustable from seconds (analog version output) K-factor Temperature Correction The K-factor of the fl owmeter decreases by 0.29% for each 100 F (39 C) increase in temperature above 70 F (21 C). The converse is true below 70 F (21 C). By programming the operating fl uid temperature in the electronics, the change in the K-Factor is automatically corrected for. Output Analog 4 20 ma, loop powered 2 wire system, digitally adjusted span Frequency Voltage pulses, 3 wire system, 1 to 10 khz square wave, open collector FET output with selectable pull-up resistors. The pulse output can be scaled so that 1 pulse represents a specifi c quantity of fl uid passing through the fl owmeter. For typical applications, the amplitude of the squarewave can be determined by: V pulse =V s (I R load ) For other options refer to the manual Span Setting For analog outputs the span setting can be adjusted without the use of electronic test equipment by programming the full scale rate using the EZ Logic kepyad. HART Protocol In addition to using the keypad for fi eld confi guration, the is also compatible with a laptop PC using a Hart Modem and EMCO EZ Comm communications software. This can be used to calibrate the 4-20 ma settings, set the 20 ma point, assign a tag or descriptor, display fl owrate, output level, total, velocity and shedding frequency. Cable Conduit Connection ANSI 3/4" female NPT. See Dimensions. ( p. 9 ) DIN PG See Dimensions. ( p. 9 ) Signal Cable 18, 20 or 22 gauge, shielded instrumentation cable. Belden #9939 double shielded cable or equivalent required for European CE rating. 32 (0) -100 (-73) -20 (-29) 100 (38) 300 (149) PROCESS TEMPERATURE F ( C) 500 (260) Measurable Flow Velocities Liquid 1.5 to 32 ft/sec (0.5 to 9m/sec) Figure 1. Ambient Temperature Range for Locally Mounted Electonics. Ambient Humidity Limit 5 100% RH non-condensing Power Requirements VDC; max power consumed: 1 watt Gas/Steam 50 ρ Where: to 260 ft / sec ρ to m / sec ρ = density in lb kg 3 ft 3 m Process Viscosity Reynolds number must be >: 20,000 (See Figure 3) Linear Range Reynolds Numbers of 20,000 to 7,000,000 2

3 Minimum Flow Velocity m/s ft/s " " 40 2" 50 3" 80 4" 100 6" 150 8" " " Kinematic Viscosity (centistokes) Figure 3. Minimum Linear Flow Velocity vs. Kinematic Viscosity. NOMINAL SIZE NOMINAL NOMINAL METER FACTOR PULSE RATE inch mm Hz/ft/s Hz/m/s pulses/gal pulses/l pulses/ft 3 pulses/m ,403 84, , , , , Table 1. Nominal Pulse Rate and Flowmeter Factor. NOMINAL SIZE FLOW RANGE FLOW RANGE in GPM in L/s inch mm min max min max , , , , , Table 2. Water Flow Rates. Notes: 1 Water values are determined at standard conditions of 60 F (15 C). 2 The minimum fl ow rate for the 1" (25 mm), and 1.5" (40 mm) fl owmeters are below the linear range the Reynolds number < 20,000). 3 The velocities used to calculate the minimum and maximum fl ow rates were 1.5 ft/sec and 32 ft/sec (0.5 m/sec and 9 m/sec) respectively. For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at Flowmeter Sizing Selecting the appropriate size fl owmeter can be critical. If the fl owmeter is over-sized, the signal strength could be weak limiting rangeability. If the fl owmeter is undersized, excessive pressure drop or cavitation may occur affecting accuracy. Use the minimum linear fl ow velocity curves and Tables 2 through 8 (minimum and maximum fl ow rates for various types of applications) for general sizing. For more detailed information, contact your EMCO representative or go to for EMCO computerized sizing program. Pressure Loss If a differential pressure transducer were connectd between pressure taps up and downstream of a vortex fl owmeter, the measured differential pressure would be the pressure loss for the device. This value can be calculated using the following equations: English... P = 2.67 x 10-4 ρ V 2 or... P = 2.50 x 10-3 ρ (Q 1 ) 2 / D 4 or... P = 4.47 x 10-5 ρ (Q 2 ) 2 / D 4 Metric... P = 1.24 x 10-5 ρ V 2 or... P = 5572 ρ (Q 1 ) 2 / D 4 or... P = 20.1 ρ (Q 2 ) 2 / D 4 Where: P = Pressure loss psi (bar) ρ = Density at operating conditions lb/ft 3 (kg/m 3 ) V = Flow velocity in ft/s (m/s) Q 1 = Volumetric fl ow rate in ACFM (Actual m 3 /min) Q 2 = Volumetric fl ow rate in U.S. GPM (L/s) D = Flowmeter internal diameter in inches (mm) Minimum Back Pressure (Liquid Service Only) The line pressure must be suffi ciently high so that no cavitation occurs. The minimum required line pressure can be obtained from the equation: PG ( 1 3 P o ) ( 2.7 P ) - P ATM Where: P G = Line pressure required psig (barg) P = Maximum pressure loss psig (barg) P o = Saturation liquid vapor pressure at operating temperature psia (bara) P ATM = Atmospheric pressure psia (bara) Example: Water fl ow rate: 0 to 200 US GPM Operating temperature: 100 F Operating pressure: 10 psig Atmospheric pressure: 14.7 psia Flowmeter size: 1.939" I.D. Specifi c weight: lb/ft 3 Solution: P = 4.47 x (200) 2 /(1.939) 4 = 7.84 P G = [(1.3) (0.951)] [(2.7) (7.84)] P G = 7.70 psig Since the operating pressure of 10 psig is higher than 7.70 psig, no cavitation occurs. 3

4 Physical Specifications Materials Wetted Parts Wing and Shedder Bar Stainless steel and Carbon steel Models 316L or the cast equivalent, CF3M Body Hastelloy Model Hastelloy Alloy C-22 Stainless steel Model (all sizes) 316L or the cast equivalent, CF3M Hastelloy Model 1" thru 4" (25mm thru 100mm) Hastelloy Alloy C-22 Carbon Steel Model (fl anged), 6" (150mm) and larger ASTM A105, A06 Grade C, and A108 Grade 1018 Electronics Enclosure 383 Aluminum All Other Parts Stainless Steel Flowmeter Classification Standard Designed to meed NEMA 4X watertight and dust tight specifi cations Explosion Proof version FM and CSA approved Explosion Proof and Intrinsically-Safe version CENELEC approved Remote Mount Electonics (RMT) Signal cable is provided to mount the electronics enclosure up to 30 ft (optional 50 ft) from the flowmeter body, and must be installed within proper electrical conduit. Local Indicator and Totalizer (LOC-TOT) The indicator displays fl owrate and total in user-selectable, engineering units. It is a two line, 8 character per line, LCD display. The totalizer enables a pulse output providing a msec pulse each time the totalizer increments. Note: This option changes the lower, ambient temperature limit to 32 F (0 C). Below 32 F, the display intensity begins to fade but doesn not affect the transmitter output. Material of Construction All models are available in stainless steel; some models can be ordered in Hastelloy C-22 or carbon steel. FM Approval (Explosion Proof) Class I, Div. I, Groups B, C, D Class II, Div. I, Groups E, F, G Class I, Div. II, Groups A, B, C, D Class II, III, Div. 2, Groups F, G CSA Approval (Explosion Proof) Class I, Div. I, Groups B, C, D Dust-ignition Proof for Class II, Div. 1 Groups E, F, G Class III Hazardous locations CENELEC Approval (Explosion Proof and Intrinsically Safe) EEX d [ib] IIC T6 and/or EEX d IIC T6. European CE Mark Approved 4

5 Accessories Flow Rectifier (EFR) When there is not sufficient straight run of pipe available or fl ow disturbance exists, use of a fl ow rectifier is recomended. When using an EFR, the straight pipe run can be a combination of 5 pipe diameters upstream and 2 pipe diameters downstream, instead of the standard 10 and 5. Flow Processor A microprocessor-based fl ow processor can be used to significantly increase the accuracy and functionality of any fl owmetering application. See the FP-93 or FP-100 General Specifications for complete details. Straight Run Piping Requirements Typical 10 diameters upstream, 5 diameters downstream. In certain applications where multiple bends or butterfl y valves are present, more straight run may be required. One 90 elbow before the meter Two 90 elbows before the meter Two 90 elbows out before the meter of plane Reduction before the meter Regulator or valve before the meter partially closed Upstream Downstream 10 D 5 D 15 D 5 D 30 D 5 D 10 D 5 D 30 D 5 D Other Installation Considerations Installation Flowmeter can be installed vertically, horizontally, or at any angle. For liquid service, the fl ow line must be full during fl owmeter operation fl ow up in vertical lines is recommended. Pressure and Temperature Taps Pressure tap should be mounted 3.5 to 7 pipe diameters downstream from the fl owmeter. The temperature tap should be mounted an additional 3.5 to 7pipe diameters downstream of the pressure tap. See Figure 2. Site Selection The fl ow measurement location should be selected to minimuze turbulence and swirl. the extent of these fl ow disturbances depends upon the piping condiguration. Valves, elbows, pumps and other piping compnents may add disturbances to the fl ow. Servicability The sensor element can be removed, and replaced, without removing the fl owmeter body from the process line, and without process shut down for process pressures below 750 psig (52 bar). Thefl owmeter K-factor is not affected by sensor or electronics servicing. The Dual option allows service of one sensor and electronics while the other transmitter provides continuous fl ow measurement. FLOW gal/min 3.5 to 7 internal diameters Pressure Transmitter 3.5 to 7 internal diameters Temperature Transmitter Figure 2. Pressure and Temperature Tap Dimensions. 5

6 1" 1.5" 2" 3" 4" 6" 8" 10" 12" Pres PSIG min max min max min max min max min max min max min max min max min max Table 3. Saturated Steam Flow Rates at Selected Process Pressures (English). 1,2 (Minimum and Maximum Operating Flow Rates in lb/hr) For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at 25mm 40mm 50mm 80mm 100mm 150mm 200mm 250mm 300mm Pres BARG min max min max min max min max min max min max min max min max min max Table 4. Saturated Steam Flow Rates at Selected Process Pressures (Metric). 1,2 (Minimum and Maximum Operating Flow Rates in kg/hr) For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at Notes: 1 Maximum fl ow velocity is 260 ft/sec (79 m/s) or Reynolods number limit or 7,000,000 whichever is less Minimum fl ow velocity is ft whereρ density in lb 74 /sec, = m/sec, where ρ = density in kg 3 3 ρ ft ( ρ ) m or Reynolds number limit of 20,000 whichever is greater. 6

7 1" 1.5" 2" 3" 4" 6" 8 10" 12" Pres PSIG min max min max min max min max min max min max min max min max min max Table 5. Air Flow Rate at Selected Process Pressures (Metric). 1,2,3 (Minimum and Maximum Operating Flow Rates in SCFH) For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at 25mm 40mm 50mm 80mm 100mm 150mm 200mm 250mm 300mm PresBARG min max min max min max min max min max min max min max min max min max Table 6. Air Flow Rate at Selected Process Pressures (Metric). 1,2,3 (Minimum and Maximum Operating Flow Rates in NCMH) For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at Notes: 1 At standard conditions of 60 F and 14.7 psia, SCFH: standard cubic feet per hour (0 C and bar, NCMH: Normal cubic meters per hour). Process temperature is 60 F (16 C). 2 Maximum fl ow velocity is 260 ft/sec (79 m/s) or Reynolods number limit or 7,000,000 whichever is less Minimum fl ow velocity is ft whereρ density in lb 74 /sec, = m/sec, where ρ = density in kg 3 3 ρ ft ( ρ ) m or Reynolds number limit of 20,000 whichever is greater. 7

8 1" 1.5" 2" 3" 4" 6" 8 10" 12" Pres PSIG min max min max min max min max min max min max min max min max min max Table 7. Natural Gas Flow Rates at Selected Process Pressures (English). 1,2,3,4 (Minimum and Maximum Operating Flow Rates in SCFH) For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at 25mm 40mm 50mm 80mm 100mm 150mm 200mm 250mm 300mm PresBARG min max min max min max min max min max min max min max min max min max Table 8. Natural Gas Flow Rates at Selected Process Pressures (Metric). 1,2,3,4 (Minimum and Maximum Operating Flow Rates in NCMH) For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at Notes: 1 At standard conditions of 60 F and 14.7 psia, SCFH: standard cubic feet per hour (0 C and bar, NCMH: Normal cubic meters per hour). Process temperature is 60 F (16 C). 2 Maximum fl ow velocity is 260 ft/sec (79 m/s) or Reynolods number limit or 7,000,000 whichever is less. 3 Specific Gravity of natural gas = 0.61 and 0.8% N 2. 4 Minimum fl ow velocity is 50 ft whereρ density in lb 74 /sec, = m/sec, where ρ = density in kg 3 3 ρ ft ( ρ ) m or Reynolds number limit of 20,000 whichever is greater. 8

9 EMCO Dimensions and Weights 1.00" (25 mm) 4.50" (114 mm) 3.12" (79 mm) 3.62" (92 mm) Wafer Connection Wafer connection is available in stainless steel (sizes 1 4" only) and Hastelloy (sizes 1 3"only). The schedule of the mating pipe's internal diameter dimension "D". 4.90" (124 mm) SIZE A B C D APPROX WT (in) (in) (in) (in) (in) (lb) A MAX. 3/4" NPT (PG 13.5) EMCO B Table 9. English Weights & Dimensions: Wafer D Figure 4. Dimensions and Weights: Wafer Connection Type, Integral Mounting. C SIZE A B C D APPROX WT (mm) (mm) (mm) (mm) (mm) (kg) Table 10. Metric Weights & Dimensions: Wafer Pipe Mount Electronics OR Wall Mount Electronics Note: For best results mount remote transmitter below horizontal pipe. 5" (127 mm) Dia " (7.14 mm) 6.5" (165.1 mm) 0.4" (10.2 mm) 4.20" (106.7 mm) 8.5" (215.9 mm) 5" (127 mm) 8.5" (215.9 mm) 8.5" (215.9 mm) 7.70" (195.6 mm) 5" 5" (127 mm) 0.4" (10.2 mm) APPROXIMATE WEIGHT (lb) 150# Flange 300# Flange 600# Flange Wafer size (in) Std Dual Std Dual Std Dual Std N/A N/A N/A N/A APPROXIMATE WEIGHT (kg) PN 16 Flange PN 40 Flange PN 64 Flange Wafer size (mm) Std Dual Std Dual Std Dual Std N/A N/A N/A N/A Figure 5. Dimensions and Weights: Remote Mounting. 9

10 Dimensions and Weights 3.12" (79 mm) 3.62" (92 mm) 1.00" (25 mm) 4.50" (114 mm) 4.90" (124 mm) 3/4" NPT (PG 13.5) Display (Optional) A MAX. EMCO B C Figure 6. Dimensions & Weights: Flange Connection, Integral Mounting. all in A B C Approx. Wt. (lb) inches Stainless Steel Carbon Steel Hastelloy size 150# 600# 150# 600# 150# 150# 300# 600# 300# 300# 300# 600# N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A C/F C/F C/F C/F Table 11. English Weights & Dimensions: Flange. all in A B C Approx. Wt. (kg) mm Stainless Steel Carbon Steel Hastelloy size PN 16 PN 64 PN 16 PN 64 PN 16 PN 16 PN 40 PN 64 PN 40 PN 40 PN 40 PN N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A C/F C/F C/FV C/F Table 12. Metric Weights & Dimensions: Flange. Notes: 1 The schedule of the mating pipe's internal diameter dimension C. 2 N/A = Not Available, C/F = Consult Factory. 10

11 Dimensions and Weights 1.00 (25 mm) 4.50 (114 mm) 3/4" NPT (PG 13.5) (79 mm) (92 mm) 4.90 (124 mm) 3/4" NPT (PG 13.5) A (Max.) FLOW C The number of bolt holes and their diameter depend upon ANSI or DIN standard. B Figure 7. Dimensions & Weights: Dual Style. all in A B C C C Approx. Wt. (lb) inches Stainless Steel Carbon Steel Hastelloy size 150# 300# 600# 150# 600# 150# 600# 150# 150# 300# 600# 300# 300# 300# 600# N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A C/F C/F C/F C/F Table 13. English Weights & Dimensions: Dual. all in mm A B C C C Approx. Wt. (kg) Stainless Steel Carbon Steel Hastelloy size PN 16 PN 40 PN 64 PN 16 PN 64 PN 16 PN 64 PN 16 PN 16 PN 40 PN 64 PN 40 PN 40 PN 40 PN N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A C/F C/F C/F C/F Table 14. Metric Weights & Dimensions: Dual. Notes: 1 The schedule of the mating pipe's internal diameter dimension C. 2 N/A = Not Available, C/F = Consult Factory. 11

12 Wiring Figures 8 10 represent typical fi eld wiring applications for the. Analog Output The may be operated using a 24 VDC power supply. The 4-20 ma output is scalable (2 wire principle.) The load resistor may be installed on supply or return line. Permissible load resistance values are shown in Figure 8. MAX. LOAD RESISTANCE (Ω) LOAD = 50 (Vs 18) Without LOCTOT Option With LOCTOT Option Permissable Load Resistance Range POWER SUPPLY VOLTAGE (VDC) P Rload Vs (18-40 VDC) Figure ma Output. Pulse Output This is an open collector pulse output using a high impedance electronic counter. V pulse will vary from: R C 0 1V to Vpulse = VS RC R pulse Note: VS Rpulse 0.16 Where: V pulse = pulse output amplitude R C = counter impedance V S = power supply voltage = minimum required voltage to trip counter V C P Vpulse Figure 9. Pulse Output. Rpulse Vs (18-40 VDC) 12

13 Wiring Cenelec ApprovedPower & Signal Wiring The fl owmeter may be operated using a 24 VDC power supply. The wiring schematic shown is for the areas defi ned by the Cenelec approval (see approval description in options section). I. S. zener barriers must have the following specifications: V max = 29 VDC = Maximum voltage which may be connected to barrier terminals J max = 110 ma = Maximum current which may be connected to barrier terminals C int = 1.5 nf = Maximum equivalent internal capacitance across barrier terminals L int = 0 H = Maximum equivalent internal inductance across barrier terminals The 4-20 ma output is scalable (2 wire principle.) The 4-20 ma loop resistor should be 250 Ω; and the pulse output is to be connected to a high impedance, electronic counter. V pulse varies from: 0-1 VDC to V pulse = V s ( Note: Rpulse V s 0.16 Where: V pulse = Pulse output amplitude V s = Power supply voltage (18 to 29 VDC) R load = Load resistance R c = Counter impedance R pulse = Pullup resistance R c R c R pulse) MAX. LOAD RESISTANCE (OHMS) Hazardous Area P LOAD = 50 (Vs 18) 18 Permissable Load Resistance Range POWER SUPPLY VOLTAGE (VDC) Safe Area or Zone 2 Zener Barrier R load R pulse V pulse Figure 10. CENELEC Approved (Intrinsically Safe). Vs ( VDC) 110/220 VACPower & Signal Wiring The fl owmeter may be operated using a 110/220 VAC power supply. The power supply board converts the 110/220 VAC to 24 VDC. The 4-20 ma output is scalable (2 wire principle.) The 4-20 ma loop resistor should be 250 Ω; and the pulse output is to be connected to a high impedance, electronic counter. (Figure 11) V pulse varies from 0 1 VDC to V pulse = 24 VDC (I R load ) Where: V pulse = Pulse output amplitude R load = Load resistance (250 Ω) I = Current (4-20 ma) L N GND AC ACC GND PULSE Analog () Analog () V pulse R load Figure 11. Frequency/4-20 ma Output Using 110/220 VAC Power. 13

14 EZ Logic Programming Map Customer Name FLUID: Exit No SavChng? Yes To Move Through Map 2 SEC 1. Use up/down and right arrows as shown in map 2. While in display menu hold down right arrow key for 2 sec. to go to programming menus 3. While in column headings press ENTER key to go to display menu. You will be prompted by "Exit?" and then "Sav Chg?". Display Menu Password gal/min x1 gal 10% To alter data 1. To alter data press ENTER key within selected block 2. Use up/down arrows to alter value 3. Use right arrow to move cursor position 4. To store data press ENTER Error code 4 Output Fluid Sensor Reset Service Password HART Display C menu C menu C menu C menu D menu D menu P menu P menu P Basic menu FlowRate Show Total Show BarGraph Show Err Code Show TotReset Yes Dsply TC 05 Sec Scan On ScanTime 05 Sec Flow Res 8 digits HART On Set Pass 0000 Sub Freq 0000 Hz 4-20 Out 0.000% Freq Out Hz Vor Ampl 0% Vor Freq 0 Hz 4 ma Cnt mA Cnt 7150 Version 3.00 Error code 1 Total Reset N Defaults No Pipe ID 1 in. Meter K WO# Tag # Density Ref Den Dens Rng 1.5 Viscos 1 cp Temp 0100 F 4-20 ma On 4-20 TC 05 sec Zero TM 0 sec Freq out Vor freq Work Order # Flw unit gal/min Tot unit x1 gal Max flow Min flow M-factor 0150 Noise Lv 003 % Direct Off Transit Puls unt ft 3 Per puls Pulse Puls unt ft 3 Per puls Puls wth 50 msec Pulse Puls unt ft 3 Per puls Puls wth 50 msec Vor freq Freq TC 05 Sec Scl freq Freq max 10 khz Freq TC 05 Sec Customer P.O. # Factory programmed to fit specific application. EZ Map Version # 14

15 Model and Suffix Codes CATEGORY DESCRIPTION SUFFIX CODES Model Stainless Steel (sizes 1 12") PhD Hastelloy (sizes 1 8") PhD Carbon Steel (Stainless steel wing) (sizes 6 12") PhD Fluid Steam or gas... S Type Liquid... L " " " " " " " " Line Size 12" mm DN mm DN mm DN mm DN mm DN mm DN mm DN mm DN mm DN Connection Wafer W Type Flange F ANSI Class ANSI Class Connection ANSI Class Rating DIN, PN PN DIN, PN PN DIN, PN PN No indicator/totalizer option STD... FM approved FM... CSA approved CSA... CENELEC approved CEN... Options Local Indicator and Totalizer LOC-TOT... Remote Mount Electronics RMT... Integral 110 VAC input Integral 220 VAC input Dual sensor and transmitter DUAL... Sensor Wires Teflon, 40 to 400 F (40 to 204 C) T (Internal) Fiberglass, 150 to 750 F (65 to 400 C) F Example Table 15. PhD Vortex Shedding Flowmeter. Notes: 1 Has 4-20 ma and/or 50% duty cycle frequency output. A 50% duty cycle frequency can be scaled. 2 FM and CENELEC approved meters come with a magnet wand. For all other meters the wand can be ordered as an option. 3 At least one local indicator is recommended at each site. If one display will be used on many meters, should be purchased separately. 4 Remote mount electronics are requried for high process temperatures (refer to the general specifi cation). The standard remote mount option comes with 30' of cable. 5 Not available with European CE Mark or FM, CSA and CENElEC approvals. 6 Wafer style meters available in stainless steel (sizes 1 4" only) and Hastelloy (sizes 1 3") only). (Not available with dual option). 7 Dual fl owmeter is not available with wafer connections or CSA approval. PhD-90-S-60-F-300-LOC-TOT-RMT-T Compatibility Chart Compatible Incompatible STD FM CSA CENELEC LOC-TOT RMT 110/220 DUAL CARBON STEEL HASTELLOY STAINLESS STEEL EUROPEAN CE MARK STD FM CSA CENELEC LOC-TOT RMT 110/220 DUAL CARBON STEEL HASTELLOY STAINLESS STEEL EUROPEAN CE MARK 15

16 Providing innovative flowmeter products and services for over three decades... (EMCO) is a long established manufacturer of precision fl owmeters for liquid, gas, and steam applications for commerce and industry. Manufactured under an ISO 9001 certifi ed quality system, which includes extensive fl ow calibration capability, engineering, applications, and service, underpining a world-wide sales and service organization totally focused on providing the best fl owmeters and customer service in the industry. 4 Manufacturing is housed in a modern plant located in Longmont, Colorado 4 Modern clean-room, mechanized assembly equipment, and computer based testing ensure the highest quality product 4 Trained professional flow specialists and technicians offer timely customer assistance 4 Factory trained and certified field technicians provide product support services V-Bar Insertion Vortex Inline Vortex Turbo-Bar Insertion Turbine MAGFLO Electromagnetic PDH Helix PDP Piston Sono-Trak P/N Rev.K Specifications subject to change without notice 600 Diagonal Hwy. Longmont, CO (303) Fax (303) sales@emcofl ow.com