NJM2718. Single-Supply High-Operating voltage Dual Operational Amplifier PACKAGE OUTLINE
|
|
- Jean Emmeline Page
- 6 years ago
- Views:
Transcription
1 Single-Supply High-Operating voltage Dual Operational Amplifier GENERAL DESCRIPTION The NJM2718 is a single-supply high-operating voltage dual operational amplifier. It is suitable for high supply voltage applications. Large-capacitance drive capability is better or equal than competing products. FEATURES Single Supply Operating Voltage Offset Voltage Large Capacitance Drive Capability Voltage Slew Rate Bipolar Technology Package Outline 3V~36V 4mV max. 1pF typ. V OH +13.V, V OL -14.V ( at V + /V - = ±1V, R L =2kΩ) V OH +3.7V, V OL.3V ( at V + =+V, R L =2kΩ) 3.V/µs typ. ( at Vin = 1Vpp, R L =2kΩ) 9V/µs typ. ( at Vin = 2Vpp, R L =2kΩ) SOP8 JEDEC 1mil, SSOP8 PACKAGE OUTLINE NJM2718E (SOP8) NJM2718V (SSOP8) APPLICATION Low-Side Current Sense PWM Motor Control System Power Supply Module Line Driver, ADC/DAC Buffer PIN CONFIGURATION ( Top View ) A OUTPUT 1 8 V + A -INPUT B OUTPUT A +INPUT B -INPUT V - 4 B +INPUT SOP8 [NJM2718E] SSOP8 [NJM2718V] Ver
2 ABSOLUTE MAXIMUM RATINGS (Ta=2 C) PARAMETER SYMBOL RATINGS UNIT Supply Voltage V + +4 V Common Mode Voltage Range V ICM V - -.3V to V + +.3V V Differential Voltage Range V ID ±4 V Voltage V O V - -.3V to V + +.3V (Note1) V Sink/Source Current for Each one Terminal I OPORT ±8 (Note3) ma Flow in Current for V + terminal I IV+ 9 (Note3) ma Flow out Current for V - terminal I OV- 9 (Note3) ma 3 [SOP8], 2[SSOP8] mw Power Dissipation P D [SOP8] (Note2) mw 3[SSOP8] (Note2) mw Operating Temperature Range T opr -4 to +8 C Storage Temperature Range T stg - to +12 C (Note 1) The output voltage of normal operation will be the Voltage Swing of electrical characteristics. (Note 2) On the PCB " EIA/JEDEC (76.2x114.3x1.6mm, two layers, FR-4) " (Note 3) Do not exceed "Power dissipation: PD" in which power dissipation in IC is shown by the absolute maximum rating. Refer to following Figure 1 for a permissible loss when ambient temperature (Ta) is Ta 2 o C. 4 (2) Package Type (1)EMP8 : ΔP D = -3.(mW/ C) (2)EMP8[Tw o Layer] : ΔP D = -.(mw/ C) (3)SSOP8 : ΔPD= -2.(mW/ C) (4)SSOP8[Tw o Layer] : ΔPD= -3.(mW/ C) Power Dissipation P D (mw) 3 2 (4) (1) (3) Ambient Temperature Ta ( C) Figure1: Power Dissipation Ambient Temperature OPERATING VOLTAGE (Ta=2 C) Supply Voltage V + (Note3) V Ver
3 ELECTRICAL CHARACTERISTICS DC CHARACTERISTICS (V + /V =±1V, Ta=2 C) Supply Current Icc No Signal ma Offset Voltage V IO Rs=Ω mv Offset Voltage Drift ΔVio/ΔT Rs=Ω µv/deg Bias Current I B Rs=Ω µa Offset Current I IO Rs=Ω µa Voltage Gain Av R L 2kΩ, Vo=±1V, Rs=Ω db Common Mode Rejection Ratio CMR -1V V ICM +13V, Rs=Ω db Supply Voltage Rejection Ratio SVR ±V V + /V - ±18V, Rs=Ω db Maximum Voltage 1 V OH 1 R L =1kΩ to V V V OL 1 R L =1kΩ to V V Maximum Voltage 2 V OH 2 R L =2kΩ to V V V OL 2 R L =2kΩ to V V Source Current I source Vin+=+1V, Vin-=V, Vo=V ma Sink Current Isink Vin+=V, Vin-=+1V, Vo=V ma Common Mode Voltage V ICM CMR 7dB V AC CHARACTERISTICS (V + /V =±1V, Ta=2 C) Gain Bandwidth Product GBW f=1khz MHz Power Band1 Power Band2 Phase Margin Gain Margin PBW1 PBW2 Gv=+1, R L =2kΩ to V, Vo=2Vpp, THD=1% Gv=+1, R L =2kΩ to V, Vo=2Vpp, THD=1% khz khz φm1 R L =2kΩ to V, C L =pf deg φm2 R L =2kΩ to V, C L =3pF deg AM1 R L =2kΩ to V, C L =pf db AM2 R L =2kΩ to V, C L =3pF db Equivalent Noise Voltage V NI Rs=Ω, f=1khz nv/ Hz Total Harmonic Distortion THD Gv=+1, R L =2kΩ to V Vo=2Vpp, f=1khz % Capacitance ci V ICM =V, f=1mhz, Vinpower=dBm pf Channel Separation CT f=2~2khz, R L =2kΩ db TRANSIENT CHARACTERISTICS (V + /V =±1V, Ta=2 C) Slew Rate 1 SR1 P SR1 N Vin=1Vpp (-.V to +.V), Gv=+1, R L =2kΩ to V, C L =pf Vin=1Vpp (-.V to +.V), Gv=-1, R L =2kΩ to V, C L =pf V/μs V/μs Slew Rate 2 SR2 P SR2 N Vin=2Vpp (-1V to +1V), Gv=+1, R L =2kΩ to V, C L =pf Vin=2Vpp (-1V to +1V), Gv=-1, R L =2kΩ to V, C L =pf V/μs V/μs Settling time(.1%) ts1 Vin=1Vpp, Gv=-1, Rin=1kΩ, μs Settling time(.1%) ts2 Rf=1kΩ, Rg=kΩ, C L =47pF μs Ver
4 ELECTRICAL CHARACTERISTICS DC CHARACTERISTICS (V + =+V, V =V, Ta=2 C) Supply Current Icc No Signal ma Offset Voltage V IO Rs=Ω mv Offset Voltage Drift ΔVio/ΔT Rs=Ω µv/deg Bias Current I B Rs=Ω µa Offset Current I IO Rs=Ω µa Voltage Gain Av R L 2kΩ, Vo=V to 3.V, Rs=Ω db Common Mode Rejection Ratio CMR V V ICM 3V, Rs=Ω db Supply Voltage Rejection Ratio SVR ±V V + /V - ±2.V, Rs=Ω db Maximum Voltage 1 V OH 1 R L =2kΩ to V V V OL 1 R L =2kΩ to V V Source Current Isource Vin+=+1V, Vin-=V, Vo=+2.V ma Sink Current Isink Vin+=V, Vin-=+1V, Vo=+2.V ma Common Mode Voltage V ICM CMR 6dB - 3 V AC CHARACTERISTICS (V + =+V, V =V, Ta=2 C) Gain Bandwidth Product GBW f=1khz MHz Power Band1 Phase Margin Gain Margin PBW1 Gv=+1, R L =2kΩ to 2.V, Vo=2Vpp, THD=1% khz φm1 R L =2kΩ to 2.V, C L =pf deg φm2 R L =2kΩ to 2.V, C L =3pF deg AM1 R L =2kΩ to 2.V, C L =pf db AM2 R L =2kΩ to 2.V, C L =3pF db Equivalent Noise Voltage V NI Rs=Ω, f=1khz nv/ Hz Total Harmonic Distortion THD Gv=+1, R L =2kΩ to 2.V, Vo=3Vpp, f=1khz -. - % Capacitance ci Vcm=V, f=1mhz, Vinpower=dBm - - pf Channel Separation CT f=1khz db TRANSIENT CHARACTERISTICS (V + =+V, V =V, Ta=2 C) Slew Rate 1 SR1 P SR1 N Vin=1Vpp (+2V to +3V), Gv=+1, R L =2kΩ to V, C L =pf Vin=1Vpp (+2V to +3V), Gv=-1, R L =2kΩ to V, C L =pf V/μs V/μs Settling time(.1%) ts1 Vin=1Vpp, Gv=-1, Rin=1kΩ, Rf=1kΩ, - - μs Settling time(.1%) ts2 Rg=kΩ, C L =47pF μs Ver
5 Supply Current [ma] Supply Current vs. Supply Voltage V IN =, R S =Ω Ta=-4ºC Ta=8ºC Ta=+2ºC Supply Voltage [±V] Supply Current [ma] Supply Current vs. Temperature (supply Voltage) V IN =, R S =Ω V + /V - =±1V V + /V - =±2.V V + /V - =+2./-.V Offset Voltage [mv] Offset Voltage vs. Temperature V + /V - =±1V, V ICM =V, n=3 MIN =.26uV/ºC MAX=9.42uV/ºC AVE=3.8uV/ºC Offset Voltage [mv] Offset Voltage vs. Temperature V + /V - =±2.V, V ICM =V, n=3 MIN =1.12uV/ºC MAX=9.93uV/ºC AVE=4.39uV/ºC Bias Current [μa] Bias Current vs. Temperature (Supply Voltage) V IN =V, R S =Ω V + /V - =+2./-V V + /V - =±1V V + /V - =±2.V Offset Current [na] Offset Current vs. Temperature (Supply Voltage) V IN =V, R S =Ω V + /V - =+2./-V V + /V - =±1V V + /V - =±2.V Ver
6 Offset Voltage [mv] Offset Voltage vs. Common Mode Voltage V + /V - =±1V, R S =Ω Ta=+8ºC Ta=-4ºC Ta=+2ºC Common Mode Voltage [V] Offset Voltage [mv] Offset Voltage vs. Common Mode Voltage V + /V - =±2.V, R S =Ω Ta=+8ºC Ta=-4ºC Ta=+2ºC Common Mode Voltage [V] Common Mode Rejection Ratio [db] Common Mode Rejection Ratio vs. Temperature (Supply Voltage) R S =Ω V + /V - =±1V V + /V - =±2.V Supply Voltage Rejection Ratio [db] Supply Voltage Rejection Ratio vs. Temperature V + /V - =±V to ±18V, R S =Ω Voltage Gain vs. Temperature (Supply Voltage) R S =Ω, R L =2kΩ 1 Voltage Gain [db] V + /V - =±2.V V + /V - =±1V Ver
7 3 Maximum Voltage vs. Frequency V + /V - =±1V, A V =+1, THD 1%, R L =2k, Ta=2ºC THD 1% 3. Maximum Voltage vs. Frequency V + /V - =±2.V, A V =+1, THD 1%, R L =2k, Ta=2ºC THD 1% Maximum Voltage [Vpp] Maximum Voltage [Vpp] M M 1k 1k M 1k M 1M 1M. 1 M M 1k 1k M 1k M 1M 1M 1 Maximum Voltage vs. Load Resistance V + /V - =±1V, R L to V. Maximum Voltage vs. Load Resistance V + =V, R L to V Maximum Voltage [V] Ta=2ºC Ta=-4ºC Ta=8ºC Maximum Voltage [V] Ta=8ºC Ta=2ºC Ta=-4ºC -1 k 1 1 k 1k 1k 1k Load Resistance [Ω]. k 1 1 k 1k 1k 1k Load Resistance [Ω] Maximum Voltage [V] Maximum Voltage vs. Current V + /V-=±1V, =+1/-1V Ta=8ºC Ta=2ºC Ta=-4ºC Current [ma] Maximum Voltage [V] Maximum Voltage vs. Current V + /V-=±2.V, =+1/-1V Ta=-4ºC Ta=2ºC Ta=8ºC Current [ma] Ver
8 4dB Gain/Phase vs. Frequency (Load Capacitance) V + /V - =±1V, V IN =-2dBm, R G =2Ω, R F =2kΩ, R L =2kΩ to V, Ta=2ºC 4dB gain/phase vs. Frequency (Load Capacitance) V + /V - =±2.V, V IN =-2dBm, R G =2Ω, R F =2kΩ, R L =2kΩ to V, Ta=2ºC 4 3 Gain 4 3 Gain Voltage gain [db] Phase C L =pf -4 Phase [deg] Voltage Gain [db] Phase C L =pf -4 Phase [deg] C L =3pF -13 C L =1pF M M 1k 1k M 1k M 1M 1M -3 C L =3pF -13 C L =1pF M M 1k 1k M 1k M 1M 1M 1 THD vs. Voltage (Frequency) V + /V - =±1V, V IN =2Vpp, A V =2dB, V O =2Vpp, R1=1kΩ, R2=9kΩ, R G =1kΩ, R L =2kΩ, BW=1~kHz, Ta=2ºC 1 THD vs. Voltage (Frequency) V + /V - =±2.V, Z IN =4Ω, A V =2dB, V O =3Vpp, R1=1kΩ, R2=9kΩ, R G =1kΩ, R L =2kΩ, BW=1~kHz, Ta=2ºC Total Harmonic Distortion THD [%] f=1khz f=2hz f=1khz Voltage [Vpp] Total Harmonic Distortion THD [%] f=1khz f=2hz f=1khz Voltage [Vpp] -4 Channel Separation vs. Frequency V + /V - =±1V, V IN =2mVpp, Z IN =2Ω, A V =4dB, V O =2Vpp, R1=1kΩ, R2=1kΩ, R G =1k, R L =2kΩ, BW=1~kHz -4 Channel Separation vs. Frequency V + /V - =±2.V, V IN =2mVpp, Z IN =2Ω, A V =4dB, V O =2Vpp, R1=1kΩ, R2=1kΩ, R G =1k, R L =2kΩ, BW=1~kHz Channel Separation [db] CH_A B CH_B A Channel Separation [db] CH_B A CH_A B -16 k 1 1 k 1k 1k 1k 1k 1M -16 k 1 1 k 1k 1k 1k 1k 1M Ver
9 Frequency Response (V IN =1Vpp, Load Capacitance) V + /V - =±1V, V IN =1Vpp, f=1khz, A V =+1, R L =2kΩ to V, Ta=2ºC 3. Frequency Response (V IN =1Vpp, Temperature) V + /V - =±1V, V IN =1Vp-p, f=1khz, A V =+1, R L =2kΩ to V, C L =pf 3. Voltage [V] Voltage [V] C L =1pF C L =pf C L =pf Time [μs] Voltage [V] Ta=8ºC Ta=-4ºC Ta=2ºC Time [μs] output Voltage [V] Frequency Response (V IN =2Vpp, Load Capacitance) V + /V - =±1V, V IN =2Vpp, f=1khz, A V =+1, R L =2kΩ to V, Ta=2ºC, Frequency Response (V IN =2Vpp, Temperature) V + /V - =±1V, V IN =2Vpp, f=1khz, A V =+1, R L =2kΩ to V, C L =pf 4 Voltage [V] C L =pf C L =pf C L =1pF Time [μs] Voltage [V] Voltage [V] Ta=-4ºC Ta=2ºC Ta=8 ºC Time [μs] Voltage [V] Frequency Response (V IN =1Vpp, Load Capacitance) V + /V - =±2.V, V IN =1Vpp, f=1khz, A V =+1, R L =2kΩ to V, Ta=2ºC 3. Frequency Response (V IN =1Vpp, Temperature) V + /V - =±2.V, V IN =1Vpp, f=1khz, A V =+1, R L =2kΩ to V, C L =pf 3. Voltage [V] C L =1pF C L =pf C L =pf Time [us] Voltage [V] Voltage [V] Ta=8ºC Ta=-4ºC Ta=2ºC Time [μs] Voltage [V] Ver
10 Equivalent Noise Voltage [nv/ Hz] Equivalent Noise Voltage vs. Frequency V + /V - =±1V, V IN =V, A V =4dB, R G =2Ω, R F =2kΩ, Ta=2ºC k 1 k 1 1 k 1k 1k Equivalent Noise Voltage [nv/ Hz] Equivalent Noise Voltage vs. Frequency V + /V - =±2.V, V IN =V, A V =4dB, R G =2Ω, R F =2kΩ, Ta=2ºC k 1 k 1 1 k 1k 1k TEST CIRCUIT V + V + 1kΩ 1kΩ V OUT V OUT 2kΩ pf 2kΩ pf V - V - Fig.2.1 Slew Rate (Non Inverting) Fig.2.2 Slew Rate (Inverting) V + signal Generator R IN R F V OUT Ω C L V - Fig.2.3 Settling Time [CAUTION] The specifications on this data book are only given for information, without any guarantee as regards either mistakes or omissions. The application circuits in this data book are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights Ver
NJM2720. Single Ultra-High speed and Wide Band Operational Amplifier
NJM272 Single Ultra-High speed and Wide Band Operational Amplifier GENERAL DESCRIPTION The NJM272 is a single, ultra-high speed and wide band operational amplifier that features 2V/μs slew rate and 1ohm
More informationLow Noise, High-Speed Dual Operational Amplifier. Vni = 3nV/ Hz typ. (at f=10khz) ft = 90MHz typ. (at V + /V - = ±2.5V)
Low Noise, High-Speed Dual Operational Amplifier NJM2719 GENERAL DESCRIPTION The NJM2719 is a high speed voltage feedback dual operational amplifier specifically optimized for low voltage noise. Combining
More informationNJM2722. Single Ultra-High speed and Wide Band Operational Amplifier
Single Ultra-High speed and Wide Band Operational Amplifier GENERAL DESCRIPTION The NJM2722 is a single, ultra-high speed and wide band operational amplifier that features 1V/μs slew rate and 1ohm load
More informationHIGH SPEED SINGLE SUPPLY OPERATIONAL AMPLIFIER V + B OUTPUT B -INPUT B +INPUT SOP8 SSOP8 MSOP8(VSP8) SOP14 SSOP14
HIGH SPEED SINGLE SUPPLY OPERATIONAL AMPLIFIER FEATURES High Slew Rate 10V/µs High Bandwidth 3MHz High Unity Gain Frequency 3.6MHz Input Offset Voltage 5.5mV max. Single Supply 3V to 36V Operating Temperature
More informationNJM2732. Rail-to-Rail Input/Output Dual Operational Amplifier
Rail-to-Rail Input/Output Dual Operational Amplifier NJM7 GENERAL DESCRIPTION The NJM7 is a Rail-to-Rail Input/Output dual operational amplifier featuring low power, low noise and a low voltage operation
More informationNJM8202. Single Supply, Rail-to-Rail Output Dual Operational Amplifier
NJM8 Single Supply, Rail-to-Rail Output Dual Operational Amplifier GENERAL DESCRIPTION The NJM8 is a Rail-to-Rail output single supply dual operational amplifier with a low noise of nv/ Hz (typ. at khz)
More informationLow Offset, Low Drift Dual JFET Input Operational Amplifier. NJM2749M, NJM2749AM : DMP8 NJM2749E, NJM2749AE : SOP8 JEDEC 150mil V + OUTPUT B INPUT B
Low Offset, Low Drift Dual JFET Input Operational Amplifier GENRRAL DESCRIPTION The NJM2749/2749A is a Precision dual JFET input operational amplifier which includes low input offset voltage:.8mv (typ)
More informationNJM2734. Rail-to-Rail Input/Output Quad Operational Amplifier
Rail-to-Rail Input/Output Quad Operational Amplifier NJM2734 GENERAL DESCRIPTION NJM2734 is a Rail-to-Rail Input/Output quad operational amplifier featuring Low power, low noise and operation from.8v.
More informationNJM4585. Low Noise, Bipolar Input Dual, Audio Operational amplifier EQUIVALENT CIRCUIT PIN CONFIGURATION. FEATURES Designed for High-Quality Sound
Low Noise, Bipolar Input Dual, Audio Operational amplifier DESCRIPTION NJM48 is a low noise bipolar input dual audio operational amplifier featuring.nv/ Hz at khz. The NJM48 features Low distortion, high
More informationNJM8801. High Quality Audio Dual Operational Amplifier FEATURES. EQUIVALENT CIRCUIT ( 1/2 Shown ) -1-
High Quality Audio Dual Operational Amplifier NJM88 GENERAL DESCRIPTION The NJM88 is a high quality audio dual operational Amplifier with bipolar technology, strikes a balance between MUSES technology
More informationNJM2734SCC. Rail-to-Rail Input/Output Quad Operational Amplifier PACKAGE OUTLINE
Rail-to-Rail Input/Output Quad Operational Amplifier GENERAL DESCRIPTION NJM74SCC is a Rail-to-Rail Input/Output quad operational amplifier featuring Low power, low noise and operation from.8v. Rail-to-Rail
More informationRail-to-Rail Input/Output Quad Operational Amplifier 8. C OUTPUT 9. C -INPUT 10. C +INPUT 11. GND(V ) 12. D +INPUT 13. D INPUT 14.
Rail-to-Rail Input/Output Quad Operational Amplifier GENERAL DESCRIPTION is a Rail-to-Rail Input/Output quad operational amplifier featuring Low power, low noise and operation from.8v. Rail-to-Rail Input/Output
More informationNJM4580 DUAL OPERATIONAL AMPLIFIER
NJM8 DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM8 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring
More informationNJM8512/NJM8513. Precision, JFET Input Operational Amplifier
Precision, JFET Input Operational Amplifier NJM8512/NJM8513 FEATURES Low Input Offset Voltage V IO =4μV max. V IO =7μV max. (Ta= -4 C to +125 C) Low Input Offset Voltage Drift ΔV IO /ΔT=5μV/ C max. (Ta=
More informationNJM12904 SINGLE SUPPLY DUAL AMPLIFIER -INPUT +INPUT OUTPUT GND(V-)
NJM1294 SINGLE SUPPLY DUAL AMPLIFIER GENERAL DESCRIPTION The NJM1294 is a single-supply dual operational amplifier, which can operate from 2V supply. The features are low offset voltage, low bias current.
More informationHigh Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier PIN FUNCTION 1. OUTPUT A 2. INPUT A 3. +INPUT A
High Current, Rail-to-Rail / Dual CMOS Operational Amplifier NJU74 GNERAL DESCRIPTION The NJU74 is a Rail-to-Rail / dual CMOS operational amplifier. Based on C-MOS technology, there are excellent features
More informationMUSES8920. High Quality Audio J-FET Input Dual Operational Amplifier - 1 -
MUSES9 High Quality Audio J-FET Input Dual Operational Amplifier GENERAL DESCRIPTION The MUSES9 is a high quality audio J-FET input dual operational amplifier, which is optimized for high-end audio, professional
More informationNJM2748/2748A. Low Offset, Low Drift single JFET Input Operational Amplifier -1-
Low Offset, Low Drift single JFET Input Operational Amplifier NJM2748/2748A GENERAL DESCRIPTION The NJM2748/2748A is a Precision dual JFET input operational amplifier which includes low input offset voltage:.7mv
More informationNJM324C. Low power quad operational amplifiers
Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low
More informationSINGLE SUPPLY QUAD OPERATIONAL AMPLIFIER
NJM SINGLE SUPPLY QUAD OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM is single-supply quad operational amplifier, which can operate from V supply. The features are low offset voltage, low bias current,
More informationNJU High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier
High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier NJU779 GENERAL DESCRIPTION The NJU779 is a Rail-to-Rail input and output dual CMOS operational amplifier that features high
More informationWide-Band,High-Speed,Low-Offset,Low-Noise Rail-to-Rail Input/Output CMOS Operational Amplifier
NJU777 Wide-Band,High-Speed,Low-Offset,Low-Noise Rail-to-Rail Input/Output CMOS Operational Amplifier GENERAL DESCRIPTION The NJU777 are Rail-to-Rail input/output CMOS single/dual/quad operational amplifiers.
More informationNJM4582 AUDIO DUAL OPERATIONAL AMPLIFIER
AUDIO DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION is the dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless,
More informationNJM13404 SINGLE SUPPLY DUAL OPERATIONAL AMPLIFIER 1 8 A
SINGLE SUPPLY DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The is single-supply dual operational amplifier, which can operate from V supply. The features are low offset voltage, low bias current, high
More informationNJM2115 DUAL OPERATIONAL AMPLIFIER
NJM5 DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION NJM5 is a low operating Voltage ( ±.V min. ) and low saturation output voltage ( ±.V P-P at supply voltage ±.5V ) operational amplifier.it is applicable
More informationHIGH SPEED SINGLE SUPPLY OPERATIONAL AMPLIFIER
HIGH SPEED SINGLE SUPPLY OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM2742 is a high speed single supply operational amplifier.the low V OL enables to treat small output signal on a single supply.
More informationMUSES8832. Rail-to-Rail Output, High Quality Audio, Dual Operational Amplifier. MUSES and this logo are trademarks of New Japan Radio Co., Ltd.
MUSES Rail-to-Rail Output, High Quality Audio, Dual Operational Amplifier GENERAL DESCRIPTION The MUSES is a Rail-to-Rail output High quality audio operational amplifier, which is optimized for high-end
More informationNJM4558C DUAL OPERATIONAL AMPLIFIER V + OUTPUT -INPUT +INPUT V -
NJM48C DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM48C integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip. Combining
More informationDual Precision Operational Amplifier
NJM79 Dual Precision Operational Amplifier FEATURES Precision V IO =6µV max. V IO =µv max. (Ta=-ºC to +8ºC) Low Offset Drift V IO / T=.9µV/ºC max. (Ta=-ºC to +8ºC) Specified for ±V and ±V operation CMR
More informationNJU7076/NJU7077/NJU7078
NJU776/NJU777/NJU778 Precision, Low Noise, Rail-to-Rail Output, CMOS Operational Amplifier GENERAL DESCRIPTION The NJU776/NJU777/NJU778 is a high precision Rail-to-Rail output Single/Dual/Quad CMOS operational
More informationNJM5532C LOW-NOISE DUAL OPERATIONAL AMPLIFIER NJM5532CG (SOP8) FEATURES PIN CONFIGURATION. EQUIVALENT CIRCUIT (Each Amplifier) - 1 -
LOWNOISE DUAL OPERATIONAL AMPLIFIER NJM3C GENERAL DESCRIPTION The NJM3C is a high performance dual low noise operational amplifier. This features low noise performance (nv/ Hz), and considerably higher
More informationLow power quad operational amplifiers
Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low
More informationNJM2737. Low Noise, Rail-to-Rail Input/Output Dual Operational Amplifier
Low Noise, Rail-to-Rail Input/Output Dual Operational Amplifier GENERAL DESCRIPTION The NJM2737 is a Rail-to-Rail Input/Output single supply dual operational amplifier featuring low voltage operation,
More informationNJM5532 LOW-NOISE DUAL OPERATIONAL AMPLIFIER
LOW-NOISE DUAL OPERATIONAL AMPLIFIER NJM3 GENERAL DESCRIPTION The NJM3 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM,
More informationPrecision Operational Amplifier
Precision Operational Amplifier NJM79 FEATURES Precision V IO =6µV max. V IO =µv max. (Ta=-ºC to +8ºC) Low Offset Drift ΔV IO /ΔT=.9µV/ºC max. (Ta=- to +8ºC) Specified for ±V and ±V operation CMR db min.
More informationNJM12904L SINGLE SUPPLY DUAL AMPLIFIER
NJM9 SINGLE SUPPLY DUAL AMPLIFIER GENERAL DESCRIPTION The NJM9 is single-supply dual operational amplifier, which can operate from V supply. The features are low offset voltage, low bias current, and drive
More informationPrecision Operational Amplifier
Precision Operational Amplifier NJMOP77/NJMOP77 FEATURES Precision V IO =6μV max. V IO =μv max. (Ta= - to +8 ) PACKAGE OUTLINE Low Offset Drift V IO / T=.µV/ max. (Ta= - to +8 ) CMR db min. Low Noise V
More informationNJU7046/NJU7047/NJU7048
NJU76/NJU77/NJU7 9V/μs High-Speed, Rail-to-rail I/O CMOS Operational Amplifier FEATURES (V + =V, V - =V, Ta= C) High Slew Rate 9V/µs Wide Bandwidth MHz Low Input Bias Current pa Rail-to-Rail Input and
More informationNJM2904C / NJM2904CA SINGLE-SUPPLY DUAL OPERATIONAL AMPLIFIER
NJM94C / NJM94CA SINGLE-SUPPLY DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM94C / NJM94CA consists of two independent, high gain, internally frequency compensated operation amplifiers, which were
More informationLow power dual operational amplifier
Low power dual operational amplifier NJM58C / NJM58CA Features Internally frequency-compensated Large DC voltage gain : db typ. Wide bandwidth (unity gain ) :.MHz typ. Low Operating Current : 5 ua/ch typ.
More informationNJU7026/NJU7027/NJU7028
NJU76/NJU77/NJU78 μa/ch, Rail-to-Rail Output CMOS Operational Amplifier FEATURES (V + =5V, V - =V, Ta=5 C, typ.) Supply Current (All Amplifiers) NJU76 µa NJU77 6µA NJU78 8µA Supply Voltage.8V to 5.5V Gain
More informationULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER
ULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM711 is an ultra high speed single operational amplifier. It can swings 6V/µs high slew rate and 1GHz gain band width product(1mhz
More informationMUSES8820. High Quality Audio Dual Operational Amplifier - + PACKAGE OUTLINE
MUSES High Quality Audio Dual Operational Amplifier GENERAL DESCRIPTION The MUSES is a high quality audio operational amplifier, which is optimized for high-end audio and professional audio applications.
More informationHigh Quality Audio, Bipolar Input, Dual Operational Amplifier
MUSES High Quality Audio, Bipolar Input, Dual Operational Amplifier The MUSES is a dual bipolar input high quality audio operational amplifier, which is optimized for high-end audio and professional audio
More informationDesignated client product
Designated client product This product will be discontinued its production in the near term. And it is provided for customers currently in use only, with a time limit. It can not be available for your
More informationNJM320A/NJM321A. Low power single channel OP-Amp
Low power single channel OPAmp NJMA/NJMA Features Input offset voltage :.mv max. Input offset voltage drift : µv/ typ. Supply current :.ma typ. at Vcc + =V Input bias current : na typ. Input commonmode
More informationHigh Quality Audio, J-FET Input, Dual Operational Amplifier
MUSES High Quality Audio, J-FET Input, Dual Operational Amplifier The MUSES is a dual J-FET input high quality audio operational amplifier, which is optimized for high-end audio and professional audio
More informationUNISONIC TECHNOLOGIES CO., LTD LM833 Preliminary CMOS IC
UNISONIC TECHNOLOGIES CO., LTD LM833 Preliminary CMOS IC DUAL OPERATIONAL AND LOW VOLTAGE NOISE AMPLIFIER DESCRIPTION The UTC LM833 is integrated circuit amplifiers which combine dual operational and low
More informationNJU77000/NJU77001 NJU77002/NJU77004
.V,.23µA/ch, Ultralow Power, Rail-to-Rail Input/Output Single/Dual/Quad CMOS Operational Amplifier FEATURES (V + =V) Supply Current NJU77/NJU77.29µA typ..23µa/ch typ. Operating Voltage.V to.v Input Offset
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationLF153 LF253 - LF353 WIDE BANDWIDTH DUAL J-FET OPERATIONAL AMPLIFIERS
LF153 LF253 - LF353 WIDE BANDWIDTH DUAL J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER
NJM271 ULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM271 is an ultra high speed hex operational amplifier. It can swings 26V/µs high slew rate and 1GHz gain band width product(1mhz
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DUAL OPERATIONAL AMPLIFIER DESCRIPTION The UTC MC1458 is a high performance dual operational amplifier. It is designed for a wide range of analog applications. The high gain
More informationNJU7116 SUPER LOW OPERATING CURRENT AND LOW OFFSET VOLTAGE TINY SINGLE CMOS COMPARATOR
SUPER LOW OPERATING CURRENT AND LOW OFFSET VOLTAGE TINY SINGLE CMOS COMPARATOR GENERAL DESCRIPTION PACKAGE OUTLINE The NJU7 is a super low operating current and low offset voltage tiny single CMOS comparator
More information4in-1out Audio Selector with Isolation amplifier
in-out Audio Selector with Isolation amplifier! GENERAL DESCRIPTION! PACKAGE OUTLINE The NJM75 is In-out stereo audio Selector with ground noise isolation amplifiers. It contains dual channel differential
More informationNJM2794. Ground Noise Isolation Amplifier PACKAGE OUTLINE
Ground Noise Isolation Amplifier GENERAL DESCRIPTION The NJM79 is a ground noise isolation amplifier designed for car audio system. It contains dual channel differential amplifier. It is developed for
More informationOPERATIONAL AMPLIFIER & VOLTAGE REFERENCE KL103/A TECHNICAL DATA DESCRIPTION. PIN CONNECTIONS (top view) OPERATIONAL AMPLIFIER
TECHNICAL DATA OPERATIONAL AMPLIFIER & OLTAGE REFERENCE KL13/A OPERATIONAL AMPLIFIER LOW INPUT OFFSET OLTAGE :. typ. LOW SUPPLY CURRENT : 3 A/op. (@ cc = ) MEDIUM BANDWIDTH (unity gain) :.9MHz LARGE OUTPUT
More informationUNISONIC TECHNOLOGIES CO., LTD
TL72 UNISONIC TECHNOLOGIES CO., LTD LOW NOISE DUAL J-FET OPERATIONAL AMPLIFIER SOP-8 DESCRIPTION The UTC TL72 is a high speed J-FET input dual operational amplifier. It incorporates well matched, high
More informationTL072 TL072A - TL072B
A - B LOW NOISE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORT-CIRCUIT PROTECTION
More informationUNISONIC TECHNOLOGIES CO., LTD LM321
UNISONIC TECHNOLOGIES CO., LTD LM321 LOW POWER SINGLE OP AMP DESCRIPTION The UTC LM321 s quiescent current is only 430µA (5V). The UTC LM321 brings performance and economy to low power systems, With a
More informationHigh Quality Audio, J-FET Input, Dual Operational Amplifier
MUSES High Quality Audio, J-FET Input, Dual Operational Amplifier The MUSES is a dual J-FET input high quality audio operational amplifier, which is optimized for high-end audio and professional audio
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD LOW POWER DUAL J-FET OPERATIONAL AMPLIFIER DESCRIPTION The UTC TL062 is a high speed J-FET input dual operational amplifier. It incorporates well matched, high voltage J-FET
More informationTEB1033 TEF1033-TEC1033
TEB1033 TEF1033-TEC1033 PRECISION DUAL OPERATIONAL AMPLIFIERS VERY LOW INPUT OFFSET VOLTAGE : 1mV max. LOW DISTORTION RATIO LOW NOISE VERY LOW SUPPLY CURRENT LOW INPUT OFFSET CURRENT LARGE COMMON-MODE
More informationUNISONIC TECHNOLOGIES CO., LTD
TL74 UNISONIC TECHNOLOGIES CO., LTD LOW NOISE QUAD JFET OPERATIONAL AMPLIFIER DESCRIPTION The UTC TL74 is a high speed JFET input quad operational amplifier. It incorporates well matched, high voltage
More informationSINGLE SUPPLY WIDE BAND
SINGLE SUPPLY WIDE BAND VIDEO AMPLIFIER GENERAL DESCRIPTION The NJM80 is a wide band video amplifier, operated on a single supply voltage. It is suitable for Y, Pb, and Pr signal because frequency range
More informationUNISONIC TECHNOLOGIES CO., LTD MC4556
UNISONIC TECHNOLOGIES CO., LTD MC4556 DUAL OPERATIONAL AMPLIFIER DESCRIPTION The UTC MC4556 integrated circuit is a high-gain, high output current dual operational amplifier capable of driving 70mA into
More informationTSV321-TSV358-TSV324. General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers. Description. Applications
General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers Operating at V CC = 2.5V to 6V Rail-to-rail input & output Extended V icm (V DD -.2V to V CC +.2V) Capable of driving a 32Ω load
More informationDual Operational Amplifier and Reference Regulator
Dual Operational Amplifier and Reference Regulator FP13 General Description The FP13 is a single chip composed of one independent OP-AMP (OPA2) and another OP-AMP (OPA1) with a 2.5V precision voltage reference
More informationTSV611, TSV611A, TSV612, TSV612A
TSV611, TSV611A, TSV612, TSV612A Rail-to-rail input/output 10 µa, 120 khz CMOS operational amplifiers Applications Datasheet - production data Out1 1 In1-2 In1+ 3 TSV611ILT - TSV611ICT In+ 1 5 V CC+ +
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationSINGLE-SUPPLY DUAL COMPARATOR. * NJM2903CMD7 don t have a A version. (Top View)
NJM9C / NJM9CA SINGLE-SUPPLY DUAL COMPARATOR GENERAL DESCRIPTION The NJM9C / NJM9CA consist of two independent voltage comparators that are designed specifically to operate from a single power supply over
More informationTS mW Stereo Headphone Amplifier. Description. Applications. Order Codes
mw Stereo Headphone Amplifier Operating from to 5.5V mw into 6Ω at 5V 3mW into 6Ω at 3.3V.5mW into 6Ω at 2V Switch ON/OFF click reduction circuitry High power supply rejection ratio: 5dB at 5V High signal-to-noise
More informationNJM2355 TWO OUTPUT HIGH VOLTAGE SWITCHING REGULATOR
TWO OUTPUT HIGH VOLTAGE SWITCHING REGULATOR NJM2355 GENERAL DESCRIPTION New JRC's high voltage switching regulator, NJM2355, is a monolithic high voltage (50V max) operation integrated circuit consisting
More informationNJM2267M. DUAL VIDEO 6dB AMPLIFIER WITH 75Ω DRIVER PACKAGE OUTLINE
DUAL VIDEO 6dB AMPLIFIER WITH 75Ω DRIVER NJM2267 GENERAL DESCRIPTION NJM2267 is a dual video 6dB amplifier with 75Ω drivers for S-VHS VCRs, HI-BAND VCRs, etc..each channel has clamp function that fixes
More informationLF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
More informationNon-inverting input 1. Part Number Temperature Range Package Packing Marking. 4558C MC4558CPT TSSOP8 Tape & Reel MC4558IN
Wide Bandwidth Dual Bipolar Operational Amplifier Internally compensated Short-circuit protection Gain and phase match between amplifier Low power consumption Pin-to-pin compatible with MC1458/LM358 Gain
More informationNJM Input / 1-Output Stereo Audio Selector
-Input / -Output Stereo Audio Selector GENERAL DESCRIPTION The NJM is Input / Output Stereo Audio Selector. The NJM consists of switches and buffer operational amplifiers. Based on the internal switch
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD SINGLE GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIER DESCRIPTION The UTC LV321 is a single op amp with low supply current. It brings good performance
More informationLM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS
LM1A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM1A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA SLEW RATE AS INVERSINGV/µs V/µs AMPLIFIER
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS DESCRIPTION The UTC LV358 is a dual op amp with low supply current and low voltage (2.7-5.5V). It
More informationMUSES03. High-Quality Sound, J-FET Input, Single Operational Amplifier for Premium Audio. GENERAL DESCRIPTION
High-Quality Sound, J-FET Input, Single Operational Amplifier for Premium Audio FEATURES High-quality sound Operating Voltage ±3.5V to ±18V Operating Current 5.8mA typ. Low Input Bias Current 5pA typ.
More informationNJM Input / 1-Output Stereo Audio Selector
NJM -Input / -Output Stereo Audio Selector GENERAL DESCRIPTION The NJM is -Input / -Output Stereo Audio Selector. The NJM consists of switches and buffer operational amplifiers. Based on the internal switch
More informationLM833 Dual Audio Operational Amplifier
LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier
More informationDesignated client product
Designated client product This product will be discontinued its production in the near term. And it is provided for customers currently in use only, with a time limit. It can not be available for your
More informationLM837 Low Noise Quad Operational Amplifier
LM837 Low Noise Quad Operational Amplifier General Description The LM837 is a quad operational amplifier designed for low noise, high speed and wide bandwidth performance. It has a new type of output stage
More informationRT2904WH. RobuST low-power dual operational amplifier. Applications. Features. Description
RobuST low-power dual operational amplifier Datasheet - production data Features D SO8 (plastic micropackage) Pin connections (top view) Frequency compensation implemented internally Large DC voltage gain:
More informationRail-to-rail input/output, 29 µa, 420 khz CMOS operational amplifiers. Description. TSV62x TSV622 TSV623 TSV624 TSV625
Rail-to-rail input/output, 29 µa, 420 khz CMOS operational amplifiers Applications Datasheet - production data TSSOP14 Features SO8 MiniSO8/MiniSO10 Rail-to-rail input and output Low power consumption:
More informationDual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
More informationUNISONIC TECHNOLOGIES CO., LTD UM609A
UNISONIC TECHNOLOGIES CO., LTD DUAL OPERATIONAL AMPLIFIER AND CURRENT CONTROLLER DESCRIPTION The UTC is a monolithic IC that includes one independent op-amp and another op-amp for witch the non inverting
More informationTL081 TL081A - TL081B
TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationNJM2871/A, NJM2872/A LOW DROPOUT VOLTAGE REGULATOR
LOW DROPOUT VOLTAGE REGULATOR GENERAL DESCRIPTION The NJM2871/A, NJM2872/A are low dropout voltage regulators designed for cellular phone application. Advanced Bipolar technology achieves low noise, high
More informationLM833 Dual Audio Operational Amplifier
LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier
More informationTS931ILT/AILT/BILT SOT23-5L Tape & Reel
Output Rail-to-Rail Micropower Operational Amplifiers n Rail-to-rail output voltage swing n Micropower consumption (µa) n Single supply operation (.7V to V n Low offset (mv max for TS93xB) n CMOS inputs
More informationADJUSTABLE PRECISION SHUNT REGULATOR NJM431SU NJM431SF NJM432SU NJM432SF 1.CATHODE 1.N.C. 2.ANODE 2.ANODE 3.CATHODE 2.ANODE 3.
ADJUSTABLE PRECISION SHUNT REGULATOR GENERAL DESCRIPTION The NJM431S/NJM432S are adjustable precision shunt regulators. The output voltage may be set to any value between VREF (about 2.5V) and 36V by two
More informationTS924 RAIL TO RAIL HIGH OUTPUT CURRENT QUAD OPERATIONAL AMPLIFIER
RAIL TO RAIL HIGH OUTPUT CURRENT QUAD OPERATIONAL AMPLIFIER RAIL TO RAIL INPUT AND OUTPUT LOW NOISE : 9nV/ (Hz) LOW DISTORTION HIGH OUTPUT CURRENT : 80mA (able to drive 32Ω loads) HIGH SPEED : 4MHz, 1.3V/µs
More informationUNISONIC TECHNOLOGIES CO., LTD MC4558
UNISONIC TECHNOLOGIES CO., LTD DUAL OPERATIONAL AMPLIFIER MSOP-8 TSSOP-8 DESCRIPTION The UTC is a monolithic integrated circuit designed for dual operational amplifier. FEATURES * No frequency compensation
More informationBand Pass Filter for Spectrum Analyzer Display
NJM Band Pass Filter for Spectrum Analyzer Display GENERAL DESCRIPTION The NJM is a band pass filter for spectrum analyzer display. It includes -band BPF amplifier, -band detector and recording level indicator
More informationLM158,A-LM258,A LM358,A
,A-LM258,A LM358,A LOW POWER DUAL OPERATIONAL AMPLIFIERS INTERNALLY FREQUENCY COMPENSATED LARGE DC VOLTAGE GAIN: 1dB WIDE BANDWIDTH (unity gain): 1.1MHz (temperature compensated) VERY LOW SUPPLY CURRENT/OP
More informationDual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP
Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One
More informationNJM2373A/76 ADJUSTABLE HIGH PRECISION SHUNT REGULATOR
ADJUSTABLE HIGH PRECISION SHUNT REGULATOR GENERAL DESCRIPTION NJM373 / NJM373A / NJM376 is an adjustable high precision shunt regulator. The output voltage can be adjusted to any value between reference
More information