MiMOMax Wireless Product Catalogue.

Transcription

1 MiMOMax Wireless Product Catalogue 1

2 TABLE OF CONTENTS CONTENTS PRODUCT CATALOGUE USER GUIDE PRODUCT & SERVICES OVERVIEW PRODUCT HARDWARE MIMOMAX WIRELESS RADIO UNIT (RU) RU MODEM MOUNTING OPTIONS INTERFACES EXTERNAL POWER SUPPLIES ANTENNAS ACCESSORIES SPARES PRODUCT SOFTWARE SOFTWARE FEATURE ENABLERS (SFES) SERVICES & SUPPORT AGREEMENTS CUSTOMER TRAINING FOR MIMOMAX PRODUCTS PATH PROFILES AND SITE SURVEYS SYSTEM DESIGN CUSTOM DESIGN SERVICES PROJECT MANAGEMENT EQUIPMENT CONFIGURATION FACTORY TESTING INSTALLATION AND COMMISSIONING HELP DESK & TECHNICAL SUPPORT REPAIRS SERVICEABLE MODULES SERVICE CHARGES SOFTWARE LICENSES & SUPPORT AGREEMENTS EXAMPLE CUSTOMER SOLUTION MIMOMAX GENERAL TERMS & CONDITIONS OF SUPPLY MiMOMax Wireless Product Catalogue 2

3 1 Product Catalogue User Guide The MiMOMax product catalogue is designed to guide the users through the process required to build a customised MiMOMax solution based on the specific needs of their critical communications network by: Guiding the users through a comprehensive list of hardware components Specifying the software options available for a given hardware configuration Advising which services to request to complete the build Determine Product Hardware Components Select Product Software Feature Enablers Specify Required MiMOMax Services To effectively build a solution, the user is advised to begin with the product hardware outlined in Section 3. Product Part Numbers are currently denoted only for MiMOMax Hardware. Please refer to the table below as an example: Radio Unit (RU) Product Part Number Example Specifying the RU Configuration Options Chosen Option Product Part Number Configured Product LRU/BRU/RRU* LRU Nominal Frequency Band Frequency Band 390MHz/420MHz/450MHz/ 470MHz/806MHz/960MHz 450MHz LRU NMXX Channel Bandwidth 12.5kHz/25kHz 025kHz Raw Data Rate 40kb/s-320kb/s 160kb/s Diversity/ Operation Mode Non- Diversity (D/N) SiSO/MiMO (S/M) NM *See section for definitions Please note that product part numbers are required for the following MiMOMax hardware components: - Radio Unit (RU) Modem Mounting (Rack/ Pole/ Wall) - MiMOMax Interface - External Power Supply - MiMOMax Antenna Options MiMOMax Wireless Product Catalogue 3

4 - Accessories MiMOMax Product Part Numbers Note MiMOMax allocates product part numbers for each hardware component, not for a complete built-up solution. This allows the user to select only the equipment and features necessary for their application. Once the user has determined the required radio hardware, they can then specify the software features and/or any MiMOMax Services they require, all of which are detailed in Section 4 & Section 5 of this catalogue. MiMOMax Wireless Product Catalogue 4

5 2 Product & Services Overview MiMOMax offers a complete range of standard and customised products and services. Please refer to the table below for a summary of these products and services: Product Hardware Radio Unit (RU) MiMOMax RUs consist of transmitters and receivers, high-speed radio modems and system controllers with a number of interfaces. Each unit can be configured to function as a point-topoint or as a point-to-multipoint radio. RUs are developed to support mission-critical infrastructure. They can provide tele-protection or/and SCADA and IP communications. They have built-in data multiplexer and RU duplexers and can offer optional external interfaces, diversity*, redundancy* and Nitro data rate boost capability. The radio unit duplexers operate in the licensed spectrum covering MHz and MHz with different sub-bands. Additional frequency options are available upon request. Channel Bandwidth options are 12.5kHz/25kHz/50kHz. All radio units offer user programmable power and user settable frequency options. *please view RU specifications- section 2.1 for further details RU Modem Mounting Kits Standard mounting include pole, wall and rack mounts. The pole & wall mounts come with sun-shade protection. The rack mount includes temperature-controlled cooling fans and front-mounted indicators. Customer Specified Interfaces Optional internal interfaces include Ethernet, Synchronous Serial (RS422/485, V35, X.21, V.11, G.703 and HSSI), Asynchronous Serial (Dual RS232) and Fibre C Optional external interfaces include 4 Wire 6 Channel Analogue Network Interface Box (4WA NIB) and Sub-Mux Digital Network Interface Box (Sub-Mux NIB) with Fibre C External Power Supplies MiMO Antennas An internal switch mode power supply with a standard input voltage range of V is provided. Optional external 150W AC Mains or 48DC isolated power supply are also available. (Optional internal power supply is planned for the future) MiMO Antennas include the Omni Directional Collinear, Dual Polarised Loop Yagi (available in Dual & Quad Arrays) & High Altitude Panel Antennas. Vertical Gain & Horizontal Gains with a nominal from 10dBi-17dBi depending on antenna type. Dual & Quad Arrays add +3dB & +6dB gain respectively. Accessories & Cables Spares Low-loss cables & mounting hardware, lightening suppressors & miscellaneous hardware as and if required. There is an extensive range of product spares that can be purchased individually or as a complete set. MiMOMax Wireless Product Catalogue 5

6 Product Software Features Software Feature Enablers (SFE s) Software features are available via MiMOMax Configuration, Control and Monitoring Software (CCMS); a web-based software that provides local and remote access to network operators for real-time monitoring. Apart from the advanced security features, the SFEs include RU Outstation Connection Licenses, Diversity capability, MiMOMax-Cognizant Adaptive Modulation (M-CAM), MiMOMax-Data Acceleration Protocols (M-DAP), MiMOMax- Routing Adaptation Protocols (M-RAP), Nitro data rate boost, MiMOMax-Power on Demand (M-PoD), Terminal Server and SNMP Support. OTAC and OTAP options are also available to enable over-the-air configuration and over-the-air programming with auto-revert. All the SFEs operate via the MiMOMax CCMS Interface. Services Service Options A wide variety of services are available including product pre-ship configuration, link planning, site surveys, system design, factory test/acceptance, installation, commissioning, project management and comprehensive training courses. Services may be requested to be delivered on- or off-site**. On-going Support and Licenses Support includes product software licenses, updates, upgrades, minor enhancements, remote access, tele-support, some preventative maintenance, problem investigation and analysis, consultancy and out of hours emergency support. Shipment Custom packaging, labelling and special shipment requirements are also available and will be quoted at the time of enquiry. Expedited delivery may incur an additional charge based on actual costs incurred. **Costs (sustenance, travel and accommodation) will be charged at cost if/when MiMOMax employees are required to travel to site MiMOMax Wireless Product Catalogue 6

7 3 Product Hardware MiMOMax products are configured products. The basic configuration comprises of a Radio Unit (RU) (with its built-in features) plus a suite of optional features that are offered based on the application-specific needs. Please note that MiMOMax Part Numbers are configured per product component, (e.g. radio unit, RU mount, MiMOMax Antenna) not per a packaged linking solution. 3.1 MiMOMax Wireless Radio Unit (RU) * Below is an illustration of the product part number for a MiMOMax RU. The RU is the baseline MiMOMax product from which a customer builds a complete MiMOMax linking solution. The alphabetical figures are substitutes for constituent product components/configurations. Please use the tables in sections 3.1.1, & to enter the appropriate product codes, as per relevant option. AAA-BBB-CCC-DDD-EEXX RU Configuration RU Nominal Frequency RU Channel Bandwidth Custom Options Operation Mode Raw Data Rate Physical form of the MiMOMax RU Please note that the physical form is identical for all configurations of MiMOMax RUs MiMOMax Wireless Product Catalogue 7

8 3.1.1 RU Configuration Options (AAA) AAA-BBB-CCC-DDD-EEXX The table below outlines the core attributes of the four MiMOMax product options. Option AAA should be substituted with the relevant RU configuration. Configured Product Network Digital Link (NDL) Optimised Protection Variant (OPV) Multi-Point Digital Link (MDL) Diversity Radio Unit (DRU; Future) MiMOMax Linking Solution Option MiMOMax Radio Unit (RU) OPTION (AAA) Linking Configuration NDL OPV MDL Tornado DRU LRU LRU BRU RRU RRU-T DRU 2 x Link Radio Unit 2 x Link Radio Unit 1 x Base Radio Unit N x Remote Radio Units N x Low Power Remote Radio Units 1 x Diversity Radio Unit Point-to-Point Point-to-Point Point-to-Multipoint Point-to-Point/ Point-to-Multipoint Shared Features (excluding Tornado) 12.5KHz & 25KHz Channels Bandwidth Full-Duplex Built-in Duplexers (External Duplexer Options Available) Built-in System Controllers Built-in 2 x 2 Transmitters/Receivers Internal VDC Power Supply MiMO Performance with QAM Modulation User Programmable Power (20db range & 10mW -1W power levels) User Programmable Frequency ( MHz & MHz) Full Range of Internal Interfaces (Async, Sync, IP, HSSI) Rack, Pole & Wall Mounting Options A Suite of Optional Advanced Software Features Configure the Same as the Primary Radio MiMOMax Tornado Key Features: 12.5KHz & 25KHz Channels Bandwidth Full-Duplex Built-in Band Pass Duplexers Built-in 2 x 2 Transmitters/Receivers User Programmable Frequency ( MHz) Linux Application Engine Standby Power Consumption <5W typical 2 Ethernet ports, 2 Async. Serial ports, 2 USB ports 4 Software Configurable I/O Ports Rack, Pole, Wall & DIN Rail Mounting Options A Suite of Optional Advanced Software Features Built-in Alarm system High stability 10MHz Frequency Reference MiMOMax Wireless Product Catalogue 8

9 Application/s PMR Site IP Linking IP Backhaul VoIP SCADA/IP Communications Repeaters Available for Long Paths Utility Tele- Protection Relay SCADA & IP Communications VoIP Point-to- Multipoint Linking SCADA & IP Communic ations Provides Additional Spatial Diversity 0x2 Unit Appendix to any Configured Products Remotely Located Compatible Interfaces Ethernet Synch/Async. Serial C37.94 Fibre HSSI External 4 Wire Audio & Sub Mux Ethernet Synch/Async. Serial C37.94 Fibre Ethernet Async. Serial C37.94 Fibre N/A Supported Modulations QPSK/16/64QAM Nitro boost: 256QAM - Adaptive Modulation 16/64 QAM (Fixed) QPSK/16/64 QAM Nitro boost: 256QAM Adaptive Modulation QPSK/16/64 QAM Nitro boost: 256QAM Adaptive Modulation MiMOMax Wireless Product Catalogue 9

10 3.1.2 RU Nominal Frequency 1 (BBB) & Power Output Level AAA-BBB-CCC-DDD-EEXX The table below details the frequency bands and corresponding RU maximum power level outputs of the RU. Option BBB should be substituted with the relevant nominal frequency, as per chosen option. Nominal Frequency OPTION (BBB) Frequency Band Max Average Transmit Power Level Per Tx 2x2 MiMO or 2x4 MiMO QPSK 16QAM 64QAM 256QAM 390 MHz MHz +30dbm +30dbm +30dbm +30dbm 425 MHz MHz +30dbm +30dbm +30dbm +30dbm 430 MHz MHz +30dbm +30dbm +30dbm +30dbm 450 MHz MHz +30dbm +30dbm +30dbm +30dbm 470 MHz MHz +30dbm +30dbm +30dbm +30dbm 869 MHz MHz +30dbm +30dbm +30dbm +30dbm 933 MHz MHz +30dbm +30dbm +30dbm +30dbm 960 MHz MHz +30dbm +30dbm +30dbm +30dbm RU Frequency Control MiMOMax RUs can be electronically tuned to match desired requirements within the duplexer tuning range. Note: Manual duplexer re-tuning may also be required RU Power Control The RF Power output of the MiMOMax transmitters can be configured to suit users needs. In the CCMS, either dbm or mw can be used by selecting the dbm or the mw of the transmitter power unit. The power is programmable in 1 db steps and the range is greater than 20db and includes 10mW to 1W power levels. 1 Additional frequencies are available on request. Please contact MiMOMax Wireless Ltd directly for more information. MiMOMax Wireless Product Catalogue 10

11 3.1.5 RU Channel Bandwidth Options (CCC) & Raw Data Rates (DDD) AAA-BBB-CCC-DDD-EEXX The table below details the RU s RF Channel Bandwidth options and corresponding raw data rates (please note that the raw data rates are dependent on the modulation scheme and not all the RUs can support the full range of modulation listed below. Section details which RUs support which modulation options): Option CCC should be substituted with the correct channel bandwidth. Option DDD should be substituted with the relevant raw data rate (numbers only) as per the chosen option. BW OPTION (CCC) Description Raw Data Rate OPTION (DDD) 2x2 MiMO or 2x4 MiMO QPSK 16QAM 64QAM 256QAM kHz Channel Spacing 040 kbps 080 kbps 120 kbps 160 kbps kHz Channel Spacing 080 kbps 160 kbps 240 kbps 320 kbps kHz Channel Spacing 160 kbps 320 kbps 480 kbps 640 kbps kHz Channel Spacing Please contact MiMOMax Wireless Limited for availability and detailed information on the Raw Data Rates within these kHz Channel Spacing Channel Bandwidth options. MiMOMax Wireless Product Catalogue 11

12 3.1.6 Diversity Operation Modes (EE) AAA-BBB-CCC-DDD-EEXX Option EE includes four possible alternatives, as detailed in the table below. Please note that diversity refers to spatial diversity, as all MiMOMax RU Modems have built-in Bi-Quadrature pattern diversity. SiSO mode or redundancy mode is currently a future option. Therefore in most cases MiMO is the accepted mode. If SiSO is specifically required, please contact MiMOMax Wireless Ltd directly. Diversity Mode OPTION (EE) Description N OR D Non Diversity OR Diversity M OR S MiMO OR SiSO Custom Option (XX) AAA-BBB-CCC-DDD-EEXX* Custom Option (XX) Description 00 Standard Radio Unit 01 External Duplexer Configurations Radio *The following low power configuration options are available: Option 1: +23 dbm RF Output < 40 Watts Option 2: +23 dbm RF Output < 40 Watts MiMOMax Wireless Product Catalogue 12

13 3.2 RU Modem Mounting Options FF-XX Custom Option (Indoor/Outdoor) Specified Mounting Option Optional mounting kits are available for each RU depending on whether it is being mounted indoors or outdoors. Please substitute FF for the required option. RU Mounting OPTION (FF) Illustration List Price (USD) RM 19 inch Rack Mount Inclusive of cooling fans to meet indoor high temperature requirements 250 PM Pole Mount Self-ventilating and is inclusive of sun shade to protect from direct solar gain 125 WM Wall Mount Self-ventilating and is inclusive of sun shade to protect from direct solar gain 185 Custom Option XX Custom Option (XX) Description 01 Indoor Mounting Option 02 Outdoor Mounting Option MiMOMax Wireless Product Catalogue 13

14 3.3 Interfaces MiMOMax RUs host a variation of interfaces both internal and external to the RU and can be ordered in a variety of combinations. These combinations are outlined in detail within this section. Appropriate interface combinations will depend on customer specific requirements and the configuration of the RU. INT-GGG-HHH-III-XXXX Core Product Global Type Interface Sub Type Interface Custom Options Compliances Sub Type Custom Options MiMOMax Wireless Product Catalogue 14

15 3.3.1 Interface Selection INT-GGG-HHH-III-CCXX The Global Type Interface, specified as option GGG, describes the umbrella digital interface board, which hosts a given combination of Sub Type Interfaces. The table below outlines the range of interface combinations available within a chosen Global Type Interface. Choosing an appropriate combination will depend on the application and configuration of the RU. Interface (GGG) Functionality Interface Option (HHH) Sub Type Custom Options (III) Description Host Radio Unit Internal Radio Unit Interface (DIF) DIF (DIF I) IP connectivity For Digital Networks Data Rates up to 256kb/s ETH 000 Ethernet (simplex 10BaseT) Optional External Alarm Output NDL MDL OPV DIF (DIF II) DIF (DIF II) Sync. Serial + IP Connectivity For Digital Networks Data Rates up to 256kb/s SS2 A00 B00 Sync Serial RS422, V.35, X.21, HSSI Optional External Alarm Output Sync Serial G.703 Optional External Alarm Output NDL OPV NDL OPV DIF (DIF III) DIF (DIF III) Async. Serial + IP Connectivity For Digital Networks Data Rates up to 256kb/s 232 Q00 R00 Dual RS232 Terminal Server S/W Optional External Alarm Output Dual point-to-point RS232 (w/o flow control) Single Point-to-Point RS232 w flow control NDL OPV MDL NDL OPV External Alarm Output DIF (DIF IV) Fibre + IP Connectivity For Digital Networks Data Rates up to 256kb/s FBR 085 (Multi-mode) 135 (Single-mode) C37.94 Compliant Full-Duplex Fibre Interface NDL OPV Continued on next page MiMOMax Wireless Product Catalogue 15

16 Interface Selection INT-GGG-HHH-III-CCXX (Continued from previous page) Interface (GGG) Functionality Interface Option (HHH) Sub Type Custom Options (III) Description Host Radio Unit External Network Interface Box (NIB) For Analogue & Digital Networks Audio multiplexer NIB (Four Wire Audio) Analogue & IP Connectivity Up to 6 x Audio Channels + 1 x Async Serial Channel 4WA 000 Six Channel 4 wire audio with E&M Signalling One RS232 w/o flow control NDL Serial Multiplexer For Digital Networks Two RS422, V.35, X.21 NIB (Sub Mux) IP Connectivity Up to 6 Channels + 1 Fibre Channel MX1 000 Four V.24 (RS232) One C37.94 NDL External Alarm Output External Interfaces: 4 Wire Audio - Network Interface Box (4WA-NIB) & Sub Mux MiMOMax 4WA-NIB 4WA-NIB with MiMOMax Radio Unit MiMOMax Sub-Mux MiMOMax Wireless Product Catalogue 16

17 3.4 External Power Supplies The MiMOMax External Power Supplies need to be low noise and fully capable of supplying sufficient peak current for the RU options previously detailed. Special compliance requirements or additional features may be required for some markets. Please note that each external power supply comes with one pair of DC leads & connectors. Should more be required, these can be purchased individually as accessories External Power Supply Options Product Part Number Description Input Voltage Output Power Rating DC V Isolated DC Power Supply (External) DC W AC V AC Mains Power Supply AC W DC (future) 12-24V Isolated DC Power Supply (Internal) DC W DC (future) 24-48V Isolated DC Power Supply (Internal) DC W MiMOMax Wireless Product Catalogue 17

18 3.5 Antennas All MiMOMax Antennas utilize a unique MiMO bi-quadrature diversity format. Transmit and receive paths are both vertically and horizontally polarised. They provide pattern diversity over direct long paths. One MiMO antenna at each link end is required for 2 x 2 MiMO and two antennas at either end are required for 2 x 4 MiMO plus for diversity option. This applies to all MiMOMax antennas & variation options. ANT-NNN-OOO-PPP-QQXX Core Product Lower Frequency Upper Frequency Custom/ Variation Options Antenna Type Antenna Gain dbi MiMOMax Panel Antenna Omni-Directional Antenna Multi-Element Loop Yagi Antenna* *Optional stacked MiMO antenna solutions are available to support long paths MiMOMax Wireless Product Catalogue 18

19 3.5.1 Antenna Type & Frequency Parameters ANT-NNN-OOO-PPP-QQXX The following table lists the current frequency parameters for all MiMOMax Antennas: Please contact MiMOMax Wireless directly for additional frequency options. Antenna Type OPTION (QQ) Nominal Lower Frequency OPTION (NNN) Nominal Upper Frequency OPTION (OOO) 369 MHz 390 MHz YD (Dual-Polarised Loop Yagi Antenna) 420 MHz 435 MHz 435 MHz 455 MHz 450 MHz 470 MHz WD (Wide Band Cross-Polarised Yagi Antenna) 420 MHz 470 MHz PD (Rugged Panel MiMO Antenna) PD (Panel MiMO Antenna) OD* (Omni Directional MiMO Antenna) 420 MHz 470 MHz 806 MHz 880 MHz 880 MHz 960 MHz 420 MHz 450 MHz 450 MHz 470 MHz *Centre Frequency must be specified MiMOMax Wireless Product Catalogue 19

20 3.5.2 Antenna Options & Specifications ANT-NNN-OOO-PPP-QQXX 400 MHz Range Antenna Type (400 MHz Range) Compact MiMO Loop Yagi Antenna Yagi Antenna Rugged Panel Antenna Omni Directional Antenna OPTION (QQ) YD WD PD OD Variation OPTION (XX) Single 01 Dual Array 02 Quad Array 04 Flat Yagi RF Flat Yagi RF Rugged Panel 00 Omni 00 Min Antenna Gain dbi OPTION (PPP) Typ Antenna Gain 10dBi 13dBi 16dBi 10dBi 12dBi 10dBi 10dBi dBi 14dBi 17dBi 11dBi 13dBi 11dBi 10dBi Drawing Front-to-Back Ratio Frequency Bandwidth (15dB return loss) 15dB 20dB 20dB 18dB 18dB 15dB N/A 20MHz 20MHz 20MHz 50MHz 50MHz 60MHz 20MHz Nominal Beam Width -3dB H 48 E Plane 48 E Plane 24 E Plane V 52 H Plane 24 H Plane 24 H Plane 47 E Plane 56 H Plane 35 E Plane 33 H Plane 60 N/A Connection Dimensions (W x H x L) Mounting Options Mounting Equipment 2 x N Type Male RG x 250 x 850mm 2 x N Type Female RG x 950 x 850mm 2 x N Type Female RG x 910 x 860mm Twin vertically spaced clamps for attachment to mm mounting pipe Mounting clamps + Antenna combiners Included Reinforcing back frame required for the Quad Array Loop Yagi also included 2 x N Type Female Length: 1500mm 2 x N Type Female Length: 2500mm Side mount bracket and clamp Brace kit for 13dBi option only 2 x Female 7/16 connectors 600 x 1000 x 150mm Twin clamps for attachment to mm mounting pipe Mounting clamps included 2 x N Type Male RG213 Antenna: 110mm dia. x 3100mm Mounting: 50mm dia. x 600mm 50mm dia. x 600mm mounting pipe Mounting clamps included Continued on next page MiMOMax Wireless Product Catalogue 20

21 Antenna Options & Specifications ANT-NNN-OOO-PPP-QQXX (Continued from previous page) 900 MHz Range* Antenna Type (900 MHz Range) OPTION (QQ) MiMO Panel Antenna PD Min Antenna Gain dbi OPTION (PPP) Front-to-Back Ratio D Frequency Bandwidth (15dB Return Loss) 16dBi dB 80MHz Nominal Beam Width -3dB Connection 20 H 34 V 2 x N Type Female Dimensions (W x H x L) Mounting Options Mounting Equipment 930 x 500 x 60 mm Twin clamps for attachment to mm mounting pipe Mounting bracket included *Omni Directional Antenna for 900 MHz Range (future) MiMOMax 900MHz Panel Antenna MiMOMax Wireless Product Catalogue 21

22 3.6 Accessories MiMOMax offers a range of accessories, detailed in the table below. These are excluded from the standard range of hardware components listed above. Product Part Number Accessory Description List Price (USD) ACC-CBL-DC DC Cable & Connector* 2m Cable that Provides DC Power to a Radio Unit; Pre-terminated with Radio Connector ACC-CBL-AL- XX01 External Alarm Cable Cable that Connects External Alarm to the Radio 45 ACC-CBL-ET-XX01 ACC-CBL-CP-XX01 ACC-RUI-LS-XX01 ACC-CBL-HX-XX01 Ethernet Cable CAT 5 (Metres) Cable Mounting Clips (Packets of 10) Lighting Suppressors RUI Helix (Metres) AVA550 Standard Category 5e Cable Clips to Support a Cable Mount Used to Reduce/Eliminate the Damage of Lightning Strikes to the Radio Un-terminated Low Loss Helix Cable /metre /metre ACC-BRF LP Band Reject Filter Low Pass Band Reject Filter; 40dB Frequency Range: MHz 125 ACC-BRF HP Band Reject Filter High Pass Band Reject Filter; 40dB Frequency Range: MHz 125 ACC-BPF XX00 ACC-BPF XX01 ACC-BPF XX02 Band Pass Filter 6 Element Comb-line Filter Pass Bandwidth: 6MHz No Mounting Panel 1 Filter Mounted on 2U Panel 2 Filters Mounted on 3U Panel 750 ACC-BPF XX00 ACC-BPF XX01 ACC-BPF XX02 Band Pass Filter 6 Element Comb-line Filter Pass Bandwidth: 11MHz No Mounting Panel 1 Filter Mounted on 2U Panel 2 Filters Mounted on 3U Panel 750 ACC-ACO Antenna Combiner Compact & Rugged 2-Antenna Combiner Frequency Range: MHz 75 * The DC External Power supply comes with one DC lead and connectors. More can be purchased if required. MiMOMax Band Pass Filter Antenna Combiner on a Pole Top MiMOMax Antenna Combiner MiMOMax Wireless Product Catalogue 22

23 3.7 Spares MiMOMax linking products are highly complex devices. Most parts are not customer serviceable* and many of the large scale integration devices are very susceptible to electrostatic damage. Although highly modular in construction, it is not recommended that individual sub-modules or circuit boards be replaced in the field, as alignment relies on experienced technicians with the appropriate test equipment. A more successful field replacement strategy is recommended for terminal swap out and re-configuration that provides the lowest possible time to repair (TTR) and highest operational reliability. It is recommended that complete spare modules (such as radio modem), are kept as spares at between 2-5% of installed base depending on location. Please note that the spares recommendations applies to all product components, including RUs, Interface Cards, External Power Supplies (if any), and Antennas Recommended Spares Installed Links Spares on Site <50 Radio Modems 2 Spare Units Radio Modems 3 Spare Units Radio Modems 4 Spare Units Radio Modems 5 Spare Units >150 Units 6 Spare Units * Please refer to the Services section for recommendations on which products are customer replaceable and which products should be replaced off field. MiMOMax Wireless Product Catalogue 23

24 3.7.2 Spares Details & Pricing The table below contains the spares available if equipment needs to be sourced. Customers should refer to the Serviceable Modules table 5.11 in the Services section, before ordering spares other than the recommended amount specified above. 400MHz Range Description Fan Front Panel 80x80 24 Volt Rack Tray 19 in Front Panel Radio Unit Casting Painted (Pair) MiMOMax Fan/LED Interface & Indicator Fan / LED Indicator Cable Assembly Input Power Filter Board Data Interface Version II & III (DIF-II & DIF-III) Data Interface Version IV (DIF-IV) Power Supply Regulator Board Duplexer Board (Notch Type) & N-Type Connectors RU Cable SMB RG405 Rx short 61.5mm RU Cable SMB RG405 Tx short 56.5mm RU Cable SMB RG405 Rx long 172mm CBL assy 16wy IDC PR-PPF 135mm CBL assy 50wy IDC 135mm PA Power Filter Board Tx Data Filter Board Rx Data Filter Board Digital Power Filter Board MiMOMax Dual Receiver MHz (Tuned) MiMOMax Dual Cartesian Transmitter (Tuned) ** MiMOMax Digital Processing System (DPS) ** Can only be supplied as a pair with DPS MiMOMax Wireless Product Catalogue 24

25 Spares Details & Pricing (Continued from previous page) 900MHz Range Description Radio Unit Casting Painted (Pair) Duplexer Board (Band Pass) & N-Type Connectors MiMOMax Dual Receiver (Tuned) MiMOMax Dual Cartesian Transmitter (Tuned)** MiMOMax Digital Processing System (DPS) RU Cable SMB Semi-Flex RG405 46mm RU Cable SMB Semi-Flex RG405 76mm RU Cable SMB Semi-Flex RG mm **Can only be supplied as a pair with DPS Note: All remaining spares details for the 900MHz product range are the same as the 400MHz product range in the table on the last page. MiMOMax Wireless Product Catalogue 25

26 4.1 Software Feature Enablers (SFEs) 4 Product Software (Via MiMOMax Configuration Control & Monitoring Software (CCMS) Basic RU pricing is kept to a minimum by pricing additional software features individually. MiMOMax SFEs are optional advanced software features for enhancing the performance of a standard MiMOMax radio. These are easily configured via MiMOMax CCMS; web-based network management software that allows easy and secure access to radio configuration, calibration and alarm functions having three optional operational modes: Local, Remote (through the local Ethernet port) and Remote Over-The-Air Tasks that can be performed via CCMS Changing Passwords Monitoring Radio Performance Configuring Radio Link Configuring SNMP Editing RF Modem Parameters (incl. Sync. Serial) Changing IP Settings of MiMOMax Radios Synchronous Serial Parameters Performing Software Upgrades Enabling/ Disabling SFEs Programming Power Levels and Frequency Preparing Radio Settings Back-up Description of MiMOMax SFEs follows in the table below: Software Feature Enablers via CCMS SFE Description Local CCMS This allows local access to the CCMS web application, via the Ethernet port of the local radio modem link. The application is password protected and allows restricted control of the local radio modem. Remote CCMS/ Over-the-Air Configuration (OTAC) Normally the CCMS web application is only accessible via the local Ethernet port of the radio and not via over-the-air link (WAN). However, with Remote CCMS enabled, CCMS is accessible via both the local Ethernet port and over-the-air link. This allows remote Over-the Air-Configuration (OTAC) of the remote link end, and often eliminates the need to travel to both radio sites. Remote CCMS includes local CCMS. Over-the-Air Programming (OTAP) OTAP allows the user to perform complete software and database updates or upgrades remotely via the RU link. When this feature is enabled, the operating and application software can be upgraded over-the-air. OTAP includes OTAC SFE plus local CCMS. Should an error occur during the re-programming process, the radios will revert to the last known working version of the software and will be able to re-establish the link. Without this feature, the software and database on the radio can only be updated or upgraded locally via the wired Ethernet port. Continued on next page MiMOMax Wireless Product Catalogue 26

27 SNMP Support MiMOMax radios can be accessed via SNMP (Simple Network Management Protocol) for network monitoring purposes. The radio can also send various traps or notifications via SNMP to a configured SNMP manager on the network. MiMOMax do not provide SNMP clients, as this product is designed to interoperate with generic SNMP clients. Note: SNMP integration can be provided at MiMOMax s standard charges for engineering design services. DNP3 Support Terminal Server MiMOMax radios can now be accessed via DNP3 (Distributed Network Protocol version 3.0) for network monitoring purposes. DNP3 is an open protocol used primarily to communicate between RTUs (Remote Terminal Units), IEDs (Intelligent Electronic Devices) and SCADA master stations (aka Control Centres). It is a highly robust, flexible and interoperable communications protocol, now widely used in electric, water, oil & gas, traffic management and similar industrial applications. Various DNP3 points can be added/removed easily using MiMOMax CCMS (Configuration Control & Monitoring System) depending on the user's monitoring needs. CCMS is web-based software, built into all MiMOMax radios for local and remote radio configuration and programming. Using DNP3, MiMOMax radio can also be configured to have unsolicited events enabled/disabled by default. The implementation is fully compliant with DNP 3.0 Subset Definition Level 3 and contains significant functionality beyond Subset Level 3. DNP3 has been adopted by Substation Committee of the IEEE Power Society ( ) as a recommended practice for implementing SCADA Master- RTU/IED communication links. The Terminal Server allows equipment that has up to two RS-232 ports*, for example serial RTUs, to be connected to MiMOMax radios. The Terminal Server packs the serial data into IP packets for transport across IP networks. *Please note the terminal server only supports the MiMOMax NDL & MDL. M-CAM (MiMOMax Cognizant Adaptive Modulation) M-CAM is MiMOMax s proprietary smart adaptive modulation scheme, designed to optimise the data throughput, while simultaneously maintaining the radio link in adverse conditions. It achieves this by adapting the RU modulation scheme depending on the measured quality of the received signal. It transverses from QPSK through to the maximum modulation scheme available and vice versa, depending on the RU channel conditions. In some circumstances, this may not be desirable (e.g. Synchronous data where fixed latency is required). If this feature is disabled, the RU modulation logic will stay fixed to the modulation scheme set, independent of signal quality. Continued on next page MiMOMax Wireless Product Catalogue 27

28 M-DAP (MiMOMax Data Acceleration Protocols) MiMOMax Data Acceleration Protocols (M-DAP) is designed to enhance VoIP and other real-time applications. M-DAP achieves a significant increase in capacity and quality by the following mechanisms: Header compression of: Ethernet IP UDP TCP RTP (Real Time Protocol) Quality of Service (QoS) Payload compression Traffic Classifier This is a unique power saving feature, which promptly turns on (<100ms link establishment time) the remote end of a radio unit transmitter only when there is data to be transmitted between RUs. The M-PoD is specifically designed for the NDL. M-PoD (MiMOMax Power On Demand Link) This feature is suited to remote sites where power consumption is an issue. It also supports cascaded links. M-PoD automatically and rapidly turns on the transmitter by promptly keying it up from idle mode in typically 80 ms to enable over-the-link data transmission. Once it is completed, the M-PoD ensures that the transmitter will stay active for a programmable time period between 1 and 255 seconds. During this time, the M-PoD confirms that all data is processed before automatically deactivating the transmitter. The stand-by power consumption in idle mode is typically 8 W. MiMOMax also offers low power options for links that have to run continuously on shorter paths thereby further reducing the power consumption to less than + 26 dbm and less than + 23 dbm power output. M-RAP is an optional suite of protocols that provide dynamic routing. This allows communications to continue in the event of a failure if alternate communication links exist. Protocols include: M-RAP (MiMOMax Routing Adaptation Protocols) OSPF (Open Shortest Path First) is used at a WAN level to determine the shortest path between two sites. OSPF selects an alternate path if and when a communications link fail thereby ensuring that communication continues. VRRP (Virtual Router Redundancy Protocol) is used at a LAN level to ensure that devices on that LAN have redundant local gateways. In the event of a failure, the remaining MiMOMax routers elect a new default gateway to ensure that devices on the local network continue to communicate with the WAN GRE (Generic Route Encapsulation) is used to transfer OSPF monitoring statistics to a central monitoring server. Continued on next page MiMOMax Wireless Product Catalogue 28

29 M-SEC (MiMOMax Security) Nitro Boost This feature enhances the critical communications network security by providing Stateful Packet Inspection (SPI); a software-based firewall that is programmed to distinguish legitimate packets for different types of connections. It only allows access to data packets that match a known active connection. Unlike stateless firewall that has no memory of previous packets, Stateful firewall holds significant attributes of each connection. Therefore, it is highly secure against spoofing attacks while offering network administrators finer-grained control of network traffic. Furthermore, the anti-lockout feature prevents the administrator from configuring firewall rules in a way that will lock him out of the web interface. With a predetermined set of rules, M-SEC optional security feature assists the network user in securely managing the webadministered devices. This allows the RU modulation logic to go up to the full 256QAM, boosting data throughput to reach a customer data rate of up to 256kbps in 25 khz channel bandwidth (raw data rate of 320kbit/sec). Out-Station Licenses Diversity Enabled (future option) This software enables a Base Station (BRU), to support a specified number of Remote Radio (RRU) Out-Stations. The number of RRU licensed, is dependent on the application requirements (for example; 10, 20, 25 supported RRUs). Diversity software enabler provides license for the 0x2 Diversity Receivers (Rx) to function, which enables additional Receiver Diversity within a link. The 0x2 MiMO Receiver provides additional Spatial Diversity and therefore, better reception and lower probability for data loss under severe fading conditions. MiMOMax Wireless Product Catalogue 29

30 5 Services & Support Agreements Services are subject to MiMOMax Terms of Trade MiMOMax offers a range of professional services to enable efficient solution integration and implementation. These services are mostly quoted on an engineering days bases. In special circumstances, these services may also be quoted in fixed prices and may be discounted to take into account the customer level of Support Agreement for some services. 5.1 Customer Training for MiMOMax Products MiMOMax offers a comprehensive product training course which is designed to bring new product users up to speed with the required knowledge to operate the MiMOMax solutions as part of their system. MiMOMax provides a standard training curriculum detailed below: Training Topics Description Company Introduction About MiMOMax Wireless Technology Explanation of MiMOMax technology Overview of MiMOMax Linking Products NDL, MDL & OPV: Specifications, Interfaces and Options Overview of MiMOMax Antennas Loop Yagi Antenna, Yagi Antenna, Dual Polarised Panel, 900MHz MiMO Panel & Omni Directional Antennas: Application, Installation and Alignment Linking Solutions and Competitive Advantage Solutions, Pricing and Serviceable Modules Advanced Network Features In-depth Explanation of Software Feature Enablers (SFEs) Configuration, Control & Monitoring Software (CCMS) Monitoring, Configuration & Update MiMOMax Software Network Management Protocol (SNMP) Linking Site Planning Performance Options, Site Planning, Design and Examples Installation and Interfacing Tuning, Maintenance and Fault Finding Basic Diagnostics Diagnostics and Troubleshooting MiMOMax Wireless Product Catalogue 30

31 5.1.1 Additional Information 1. Approximate time frame of training courses varies from two to three days. 2. The cost per trainer per engineering day is listed in Services Section. 3. The costs listed in the Services Section indicate the rate for onsite training days in New Zealand. MiMOMax does supply offsite training. All travel costs, sustenance accommodation and per Diem allowances are charged to the customer at actual cost. 4. The number of trainers required depends on the number of trainees (Normally, 1-2 trainers are required per training course). 5. The curriculum listed above is the standard MiMOMax curriculum. MiMOMax customises training courses to suit individual customers. Please contact MiMOMax Wireless directly regarding a customised training curriculum. 5.2 Path Profiles and Site Surveys Customers may request path profiles be run to ascertain the theoretical path profile, based on customer supplied location information. This will enable budgetary link performance calculations to be provided and recommendations to be made based on theoretical availability and equipment performance. MiMOMax will produce electronically supplied reports using the tools available. On-site path and site survey work can also be contracted to validate the theoretical path profile results. This will considerably improve the accuracy of theoretical models Additional Information 1 MiMOMax will not take responsibility for any variances between the theoretical and actual measured results. 2 Path profile work is charged per engineering day. Typical costs for a single path profile are about ¼ day engineering charge per path pair. Please view Section 5.12 for exact cost details. 3 Please note that if contracting any on-site services, all travel costs, sustenance accommodation and per diem allowances are charged to the customer at actual cost. 5.3 System Design MiMOMax offers limited system design services, whereby MiMOMax will work with both the customer and the customers suppliers to complete systems or network design work, to ensure that fully integrated systems perform to specifications. System Design work may be charged at daily or hourly engineering services charge. Please refer to Section 5.12 for specific costs. 5.4 Custom Design Services MiMOMax fulfils requested customised product designs if requests are achievable. Custom design services are charged per engineering day. Please view Section 5.12 for specific costs. Listed prices are subject to change, depending on the nature of the customization required. MiMOMax Wireless Product Catalogue 31

32 5.5 Project Management To ensure successful and timely implementation, MiMOMax offers full project management for all aspects of the project. When a customer requests MiMOMax to take on systems responsibility or responsibility for ensuring that aspects of the implementation meet specific customer requirements, MiMOMax will quote for project management services. Project management services are charged at a daily basis for all time involved in planning, coordinating and monitoring progress of the project. For specific costs, please refer to Section Equipment Configuration Prior to shipment, MiMOMax can be requested to pre-configure each RU and network interface to the customer specified configurations. It is the customer s responsibility to define the required settings and configurations. Typical charges for this service are approximately ½ engineering day per terminal end. Please refer to Section 5.12 for specific costs. If there are a large number of terminals to be configured, a separate quote may be requested. 5.7 Factory Testing MiMOMax offers factory acceptance services for customers wanting to verify equipment performance prior to shipment. Factory acceptance can be progressed on behalf of a customer and/ or in the customer s (or customer s agents) presence. If the customer is required to be present then it is the customer s responsibility to provide their own transportation, accommodation costs and any daily allowances. Preparation and documentation time will be additional to on-floor equipment testing time. Charges for acceptance testing are detailed within Section Installation and Commissioning MiMOMax does not directly employ qualified high voltage electrical and construction personnel or high site riggers. MiMOMax neither undertakes site preparation works nor erect antenna masts. MiMOMax installation services are normally limited to installing MiMOMax equipment into pre-prepared sites, where sites have been prepared by regionally qualified personnel. MiMOMax will do final terminations (where such terminations do not require rigging skills or local licenses), equipment installations and connections to low voltage power sources provided. MiMOMax will provide commissioning services to ensure that the equipment is performing to the specifications in service. Charges for installation and commissioning are based on engineering days and do not include associated incidental costs. Please refer to Section 5.12 for specific costs. MiMOMax Wireless Product Catalogue 32

33 5.9 Help Desk & Technical Support The following charges apply to Help Desk and Technical Support services and are subject to MiMOMax Terms of Trade (Section 7). A call out fee of USD $250 for out of hours support may also apply depending on customer support agreement level. Description Price USD Help Desk Support Hourly Rate $120/hour Help Desk Support Daily Rate $700/day On Site Emergency Support Fixed Rate $1200 Help Desk Technical Services are subject to the same provisions as Services above Additional Information 1. All Services which are not identified as hourly or fixed costs are charged per day, or part thereof (including any preparation and travel time). 2. Charges may be discounted in line with the level of Service Agreement the customer is contracted to. 3. Any additional expenses including travel, sustenance, accommodation, freight and any per diem, are charged at the actual cost Repairs Repairs are available on: time and material basis daily rate plus materials fixed price basis Repairs may be discounted as part of a Support Agreement. In all cases, freight to MiMOMax is at the cost of the customer and return freight to the customer is at MiMOMax s expense. Rate for Repair Price USD Hourly Rate Daily Rate $100 per Hour $700 per Day Fixed Rate Interface Card Repair $350 Fixed Rate Internal/External Power Supply Repair $250 Fixed Rate Radio Modem Repair and Re-calibration (All Modules) $1250 MiMOMax Wireless Product Catalogue 33

34 5.11 Serviceable Modules Please note, before seeking external assistance, MiMOMax recommends customers utilise the following Serviceable Modules table as a guide to understand what may be required for repair and/or what can be repaired internally. MiMOMax Radio Servicing Strategy External Modules MiMOMax Antennas Connectors on Antenna Feeders MiMOMax External Power Supplies Fan Clean Fan Failure DC Power Lead Mechanics (Rack tray, Front Panels etc.) NIB and Board Indicator Board on rack tray Customer Replaceable Customer Replaceable Customer Replaceable Customer Serviceable Customer Replaceable Customer Replaceable Customer Replaceable Customer Replaceable Customer Replaceable Internal Modules Power filter Board Customer Replaceable DIF (incl. Serial and Ethernet Connectors) Customer Replaceable with Training and Care Power Supply Board Customer Replaceable with Training and Care Duplexers (incl. RU Connectors) & Tune Customer Replaceable with Training and Care Internal RU Coax Customer Replaceable with Training and Care * Inter-board Cables Customer Replaceable with Training and Care Inter-board Filters Customer Replaceable with Training and Care Rx Board Return to MiMOMax Service Center Tx Board Return Unit to Factory for Repair Digital Board Return Unit to Factory for Repair * Recommended to be returned to MiMOMax Service Centre (Note: Also Customer Replaceable, given the customer has undergone MiMOMax training and care is taken ** Detailed fitting instructions will be supplied with each replacement module See Figure 1 for a Diagram describing the PCB assemblies MiMOMax Wireless Product Catalogue 34

35 Figure 1: PCB assemblies MiMOMax Wireless Product Catalogue 35

36 5.12 Service Charges Please refer to the table below for the specific MiMOMax Service Charges per engineering day: One engineering day is regarded as 8 hours Description Price USD Training (Engineering Days) $1200 Site Surveys & Path Profiles (Engineering Days) $650 System Design (Engineering Days) $850 Custom Design Services (Engineering Days) $850 Project Management (Engineering Days) $850 Equipment Configuration (Days) $850 Factory Test (Engineering Days) $600 Installation (Engineering Days) $600 Commissioning (Engineering Days) $650 Help Desk & Technical Support Refer to Section 5.9 Repairs Refer to Section Additional Information 1 All services that are not identified at hourly or fixed costs are charged on per day or part thereof (including any preparation and travel time). 2 Charges may be discounted in line with the level of service agreement contracted to. 3 Any additional expenses including travel, sustenance accommodation, freight and any per diem allowances are charged at the actual cost. MiMOMax Wireless Product Catalogue 36

37 6 Software Licenses & Support Agreements Description Bronze Silver Gold Platinum Support Fee 2.5% 5% 7.5% 10% Services Discount Level (Excludes Expenses) Note 1 Prices as per List 25% Discount off List Prices 40% Discount off List Prices 50% Discount off List Prices Software Licenses Included Included Included Included Configuration Back Up. S/W O/S & Data Bases Help Desk Access Out of Hours Help Desk Response Time for all Enquiries Restoration Time for Problems Repair Times for Problem Resolution Technical Support Services Hardware & Software Not Available Included Included Included NZ Working Hours Only Charges Apply Not Available Charges Apply Free of Charge Free of Charge 9am-5pm. Usual NZ Working days 24x7 Free of Charge 24x7 Free of Charge 48 Hours 24 Hours 12 Hours 4 Hours Best Endeavours 48 Hours 24 Hours 24 Hours Best Endeavours 20 Working days 10 Working Days 5 Working Days 48 Hours 24 Hours 12 Hours 12 Hours On Site Engineering Services. Hardware and Software Usual Charges Apply. Engineer dispatched within 5 working days Usual Charges Apply. Engineer dispatched within 3 working days Usual Charges Apply. Engineer dispatched within 2 working days Usual Charges Apply. Engineer dispatched within 48 hours Remote Access Enable remote Access Customer Access to FTP Server Not Available Available Available Available Not Available Available Available Available Remote Investigation and Analysis Not Available 25% Discount off List Prices 40% Discount off List Prices 50% Discount off List Prices Network Monitoring Not Available On Application On Application On Application Preventative Maintenance Not Available On Application On Application On Application MiMOMax Wireless Product Catalogue 37

38 7 Example Customer Solution The table below is an example that illustrates how a typical MiMOMax customized solution is built. Hardware, software and services are individually selected to suit specific customer requirements. This example contains the necessary components to build a single MiMOMax Point-to-Point NDL link, which is remotely programmable and comes with one year of Gold Support Agreement. Component Quantity ITEM Product Part Number Description Hardware Radio 2 LRU LRU NM MiMOMax NDL Point-to-Point Link Mounting 2 Pole Mount PM RU Pole Mount with sun shade Interface 2 Ethernet INT-XXX-ETH-XXX-XXXX Ethernet Interface Antenna 2 Loop Yagi ANT YD01 Single Dual Polarised Loop Yagi Antenna Accessories 2 DC Cable & Connectors ACC-CBL-DC-0201 DC Cables Connectors Software Radio Operation Software 2 Local CCMS N/A MiMOMax CCMS Software Support Radio Support 1 Gold Support Contract N/A MiMOMax Gold Rate Support Agreement