Remote Site Monitoring

Transcription

1 Remote Site Monitoring FEATURES AT A GLANCE Codan Radio Communications now offers Remote Site Monitoring options that provide live site information, giving you the power to respond intelligently to communications failures that affect your system today, and to prevent the ones that will happen tomorrow. REMOTE SITE MONITORING SOLUTIONS A Remote Site Monitoring package can be added to any Codan MT-4E series repeater or base station. Real-time or historical data collected at the site is passed to a centrally located PC equipped with the APEX software over one of the following backhaul interfaces: 1. Existing Radio (RF) Link: a. Directly from the site, or b. Relayed via intermediate remote repeater sites 2. IP Connection on a Local Area Network (LAN) NOTE: RF Link must transmit Remote Site Monitor data in Analog mode only. Console Tone Remote SiteCommander SiteCommander Remote Gateway PC with APEX software IP SiteCommander Remote Radio Site Remote Radio Site Link Repeater Summit Summit IP Connection LAN Remote Radio Site EN Issue 2 7/2016

2 Remote Site Monitoring MT-4E SYSTEM INTEGRATION Codan MT-4E series radios interface with the Remote Site Monitoring on-site controller via direct wireline connections to analog and digital I/O available on the system subrack. The lines that can be monitored include: Codan MT-4E Inputs/Outputs to Controller Digital Inputs MT-4E Subrack Pin Rx COR J1-7 Rx A/D Mode J4-10 Rx Health (Active Low) J6-2 Tx PTT In J1-3 Tx PTT Out J5-6 Tx Forward Power Alarm J5-2 Tx Health (Active Low) / Tx VSWR Power Alarm (RSS Jumper Selectable) J5-3 VHF / UHF 30W PA Low Forward Power Alarm J5-10 VHF / UHF 30W PA High VSWR Alarm J5-11 VHF / UHF 30W PA General Fault Alarm J5-14 Digital Outputs Tx PTT In J1-3 Rx Squelch Override J4-9 Analog Inputs Line Voltage V J4-5 Regulated Voltage V J4-7 Rx RSSI J5-7 Other external sensors that can interface with the controller include: External Sensor Inputs to Controller Digital Inputs External Power Amplifier Summary Alarm External AC Power Supply Alarm Output Door Alarm Antenna and Cable VSWR Alarm Device External W Amplifier External AC to DC Power Supply Door Alarm Connector Antenna and Cable Monitor Analog Inputs AC Line Voltage Ambient Temperature DC Current RF Power: Forward and Reverse (VSWR) Antenna & Cable: Forward and Reverse (VSWR) AC Voltage Sensor Temperature Sensor Differential Voltage Sensor Bidirectional Power Sensor Antenna and Cable Monitor

3 Controller Specifications Controller Summit SiteCommander Codan Application Monitoring over IP Monitoring over RF Link Management Software Mounting APEX 19 Rack (1RU) Power Input +8.0 VDC to VDC VDC to VDC Average current consumption VDC VDC (15 ma in sleep mode) Operating Temperature C to C Interface 10/100/1000 Base-T Ethernet 1200/2400 bps FFSK over RF Gateway Interface via Ethernet or Serial Digital Inputs Number available (default) 48 8 Input range Supported input types Digital Outputs 0 VDC to VDC Contact closure, switches, open collector, voltage inputs Number available (default) 12 8 Output range Supported output types Analog Inputs Up to ma Open Drain Number available (default) 32 8 Input range Supported input types Filters Analog Outputs 0 VDC to VDC or 4 ma to 20 ma 16 bit resolution Hold time, threshold trigger set points per input, software defined qualifiers 0 VDC to +5.0 VDC or 0 VDC to VDC or 0 VDC to VDC (external adapter) 8 x10bit A/D Hold time, threshold trigger set points per point Number available (default) 4 N/A Output range Up to ma N/A Summit Punch Block (Included)

4 Remote Site Monitoring SENSOR SPECIFICATIONS Temperature Sensor (SiteCommander) Application RF Link (SiteCommander) ONLY Span -55 to +125 C Accuracy -25 to +100 C ± 1.5 C (nominal) -55 to +125 C ± 2 C (nominal) Current Draw 2 ma per sensor Designed to monitor ambient temperature in an enclosed environment. RJ45 connection provides plug-in connection to the SiteCommander without using analog inputs. Temperature Sensor (Summit & SiteCommander) Application The Outdoor Temperatures Extended Reach Sensor detects outdoor ambient temperature which can be used over much longer leads than other temperature sensors (up to 100 feet) with the Summit or SiteCommander. IP (Summit) and RF Link (SiteCommander) Span -40 to 49 C Accuracy ± 1.5 C Operating relative humidity 5% to 95% non-condensing Cable length 10 feet (3m); 50 feet (15m); 100 feet (30m) Mounting Clip Included DC Current Sensor The sensor/shunt combination is designed to measure DC current. Includes a Differential Voltage Sensor (also sold separately for voltage measurements that are not referenced to ground) VDC In 7 to 20 VDC Current 2 ma Max. Operating Temp -40 to +65 C +IN/-IN Differential Input Voltage = ± mv Common Mode Voltage (CMV) = 0 65 VDC AOUT 0 5 VDC Dimensions 52 mm x 36 mm x 28mm (L x W x H) Weight 15 g 100mV DC Ammeter Shunt 5, 20, 30 or 50 AMP AC Voltage Sensor The AC Voltage Sensor will measure AC voltage in a single phase system. Environmental Functional temperature -25 to +70 C Input VAC, VAC Output 0 5 VDC >1 kω Enclosure Snap on to DIN rail 35 x 7.5 mm Door Contact Sensor The sensor changes voltage when a magnet mounted near the sensor switch is moved away from or closer to the sensor switch. Loop Type Closed Electrical Configuration Normally Open Maximum Switching Voltage 160 VDC Maximum Switching Current 0.4A Cable Length 50 feet (15 meters) 100 feet (30.5 meters) 150 feet (46 meters) Maximum Gap 1 1/4 (31.75 mm)

5 SENSOR SPECIFICATIONS (CONTINUED) Bidirectional Power Sensor Bi-directional power monitor sensors provide a DC voltage output corresponding to an input RF signal. Provides precise forward and reflected power measurements. Bandwidth 50 MHz Frequency Range MHz MHz MHz MHz Measurement Range 5 W W Insertion Loss (typical) 0.1 db VSWR 1.1:1 Maximum RF Connectors N Type DC Connectors RCA-F standard Impedance 50 Ohms Dimensions x 2.25 x 1.25 inches (3.5 x 5.7 x 3.2 cm) Weight 0.5 lb (0.2 kg) Antenna and Cable Monitor Antenna and Cable Monitors are designed to detect antenna and cable faults that transmitter-internal VSWR monitors may not detect, and also provides accurate in-line power measurement functionality. VSWR 1.07 Frequency Range MHz MHz MHz Measurement Range 2.5 W W or 12.5 W to 500 W Insertion Loss 0.1 db RF Connectors N Type Alarm Set Point (1.3 to 2.5) to 1 Impedance 50 Ohms Reflected Directivity 30 db Current Draw Vdc

6 SOFTWARE SPECIFICATIONS Software APEX and APEX EMS Key Features Server Core Requirements Operating System Processor Memory Network Card Hard Drive Client Requirements Operating System Processor Memory Network Card Hard Drive Resolution License Options APEX APEX EMS Event logging keeps track of incidents Immediate notification of alarm conditions Real-time presentation by polling of operator selected data Alarms can be sent to one or many operators Visual, audible and pop-up alarm notification Custom background map/graphics to suit your application Permission levels settable to company defined security measures Outputs at a given site can be mapped to change based on an event occurring at the same site or multiple sites Windows Server 2008 or higher-recommended Intel Generation 3 (Minimum) 4 GB RAM (Minimum) 10/100 Ethernet Card 500 MB free space-recommended Windows XP/Vista/7/8/10 Intel Generation 2 (Minimum) 128 MB RAM 10/100 Ethernet Card 10 GB 7200 RPM, 20 MB free space 1024x768 (Minimum) 10 simultaneous users; unlimited number of sites. 10 simultaneous users; unlimited number of sites. Adds SNMP Network Manager functionality that captures SNMP traps from other networked devices and displays them on APEX. CODAN is a trademarks of Codan Limited. Other brand, product and company names mentioned in this document are trademarks or registered trademarks of their respective holders. Values noted are typical. Equipment descriptions and specifications subject to change without notice or obligation. CODAN RADIO COMMUNICATIONS EN Issue 2 7/ Australia: Canada: US: UAE: LMRsales@codanradio.com