MICROWAVE COAXIAL CONNECTORS

Transcription

1 !Note Please read rating and!cution (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc. O0E4.pdf This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering. Microwave Coaxial Connectors MICROWVE COXIL CONNECTORS Murata Manufacturing Co., Ltd. Cat.No.O0E-4

2 !Note Please read rating and!cution (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc. O0E4.pdf This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering. CONTENTS Part Numbering Microwave Coaxial Connectors with Switch SMD Type Notice 5 Package 8 GSC type 9 Notice Package 4 FSC type 5 Notice Package F type Notice 5 Miniaturized Microwave Coaxial Connector Cable List 7

3 o Part Numbering The structure of the "Global Part Numbers" that have been adopted since June 00 and the meaning of each code are described herein. ( If you have any questions about details, inquire at your usual Murata sales office or distributor. ) Coaxial Connectors (Chip Type Receptacle) (Global Part Number) MM q 79 w -7 e 00 r R t y qproduct ID Product ID wseries MM Code eindividual Specification Code () Microwave Coaxial Connectors (Chip Type Receptacle) Series F Type Straight F Type Right ngle FSC Type SWD Type GSC Type Code Individual Specification Code () -5 Discrete Terminal -6 Switch Connector SMD Type -7 Connector SMD Type rindividual Specification Code () Code Individual Specification Code () 00 Serial tpackage Product ID Code Package Product ID ulk R Reel ypackage Detail Code Package Detail FSC, SWD, GSC Type 000pcs. /Reel (ø78mm) SWD Type, 000pcs. /Reel (ø0mm) 4 FSC Type, 4000pcs. /Reel (ø0mm) 5 GSC Type, 5000pcs. /Reel (ø0mm) Coaxial Connectors (with Cable) (Global Part Number) MX q FG w 76 e r t y qproduct ID Product ID MX Coaxial Connectors (with Cable) wconnector () Code Connector () FG FSC Type for 76 Cable FK FSC Type for 8 Cable TK GSC Type YH F Type ecable Code Cable 6 0.8D, PE, Double Shield Line 6 0.8D, PE, Single Shield Line D, FEP, Double Shield Line D, FEP, Single Shield Line 8 0.4D, FEP, Single Shield Line D, PF, Single Shield Line, Single Line 9 0.4D, PF, Single Shield Line, Spiral rconnector () Code Connector () FG FSC Type for 76 Cable FK FSC Type for 8 Cable TK GSC Type YH F Type XX None Connector tlength Expressed by four figures. The unit is mm. From first to third figures are significant, and the fourth figure expresses the number of zeros which follow the three figures. Ex.) Code yindividual Specification Code Expressed by two figures. Length 500mm = 500 x mm = 00 x 0

4 Microwave Coaxial Connectors Microwave Coaxial Connectors with Switch SMD Type Features. The coaxial connector with switch is very useful for characteristic measurement of hand held phone and microwave circuit.. It is possible to switch the line connection and desconnection easily by special probe.. Small size, low profile. Size xx.75mm (LxWxH). 4. Excellent characteristic. Low IL 0.d max.. V.S.W.R.. max. Isolation 5d min. (at DC to 6GHz). 5. Surface mountable and reflow solderable. 6. Tape package available. MM C Terminal Side.75 dia. 0.8 R Terminal Side IN OUT GROUND pplications Cellular phone, W-LN, Other wireless and measerement equipment. Part Number Rated Voltage (Vrms) MM max. Impedance : 50 ohm Contact Resistance (ohm) 0.05 max. Withstand Voltage (Vrms) Insulation Durability Resistance (M ohm) (cycles) Frequency Rating Temperature Range (degree C) 00 (C) DC to 6GHz -40 to +90 VSWR Insertion Loss (On) (d). max. 0. max. (DC to 6GHz) (DC to GHz) Isolation (Off) (d) 0 min. (DC to GHz) Inner Electrode (C) Stainless Steel Gold plated Inner Electrode (R) (material) Copper lloy Gold Plated Outer Electrode (material) Copper lloy Silver plated Measurement Probe Dimensions MM606 MXGS8RK000 -Dia..6±0.5 6±0.5 9±0. Dia. 0±0. Dia. 0±0. SM-J Dia..8±0. Dia. 5.4±0. Dia. 7±0. 5.±0. 9±0..±0. 00±4 (5.4) (4.8) 0.8D Cable SM-J (4.0) (.5).85±0..65±0. (.5) Dia..±0. Dia. 4.±0. Dia. 5.8±0. Part Number : MXGS8RK000 Continued on the following page.

5 Continued from the preceding page. Structure Probe OUT IN OUT IN Without Probe With Probe Standard Land Dimensions. Standard pattern dimensions Please design I/O pattern so that the impedance match 50 ohm including the land pattern. The material of PC is the epoxy resin of grass fabric base. (εr=4.8). Thickness is.0mm. The solder resist should be printed except for the land pattern on the PC Through hole.. 4. LND ELECTRODE (.5) (.5).74. Standard metal mask pattern There is possibility to have the contact failure by solder shifting into contact point, if the excess solder is used by non standard metal mask pattern The standard solder cream metal mask drawing (Mask thickness 0.5mm) 4

6 Notice Notice (Storage and Operation Condition). Environment Conditions () This product is designed for use of electrical equipment in the environment (temperature, humidity, atmospheric pressure and etc.) specified in this approval drawing: it may not be used in the following environments or under the following conditions : (a) mbient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, mmonia gas, Sulfuric acid gas, Nitric oxie gas, etc.) (b) mbient air containing volatile or combustible gas. (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles. (e) In direct sunlight (f) Other environments similar to the above conditions. () Contact the manufacturer before using the product in any of the above environments or under any of the above conditions.. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use, if the product has been stored for more than 6 months. Temperature : -0 to +40 degree C Humidity : 5 to 85 % RH 5

7 Notice Notice (Soldering and Mounting). Reflow soldering Soldering must be carried out without exceeding the allow able soldering temperature and time shown within the shaded area of FIGURE "llowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in FIGURE "llowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in FIGURE "Reflow Soldering Standard Conditions". Use the pattern and Metal mask pattern is illustrated in details. There is the possibility to have the contact failure by solder shifting into contact point, if the excess solder is used by non standard metal mask pattern.. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 50 degree C Time 60 to 0 s. Soldering Temperature (at the tip of the soldering iron) less than 50 degree C Time less than s.. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering. llowable Temperature and Time Reflow Soldering Reflow Soldering Standard Conditions Temperature (degreec) Temperature (degreec) Pre-heating 50±0 degreec 60-0 sec Time (sec.) Solder : Sn60% - Pb40% Peak temperature 5±5 degreec 0-40 sec. Time (sec.) 0 sec. max. Measuring point of temperature : In-Out Terminals of Device Reflow Soldering : oth Convection and Infrared Rays : Hot ir : Hot Plate 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. 5. Please note the following in case of soldering terminals or leads of the product. () Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.0wt%). () Flux should be cleaned thoroughly. 6. Please mount this product at the position so that stress by wrap and/or bend of the PC may not apply to it. 7. Please avoid the cleaning of this product. 6

8 Notice (Handling) Notice Notice (Handling). utomatic measurement probe (MM606) utomatic measurement probe (MM606) should be used on the condition in Fig. for good connection without any damages. The engagement strokes from the flange to the tip of probe is 8.8mm to 9.78mm with vertical (0+/- degree) direction. Fig. Insertion the automatic measurement probe (MM606) in receptacle (MM ) 0 +/- degree 8.8(Minimum Point for using) 9.78(Maximum Point for using).5 (Using Range). L type probe with lock function (MXGS8RK000) Do not try to pull the cable, when a connector with a coaxial cable is handled. Do not give a twisted torque to the cable and connector. Mechanical stress: The stress to the connector should be limited as figure shown right. () Stress to the housing. Stress and : 0.7N Max. () Stress to the outer sleeve. Stress C: 0.6N Max. Stress D: 0.6N Max. () Cable pull strength. Stress E: 0.7N Max. Mechanical stress after engagement C D MM E. Usage Condition () Do not apply electrical voltage greater than specified in the catalog. It might cause degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. () Confirm that product perfomance is not influenced with any other components or materials which directly contact products. PC 4. Handling Do not apply excessive shock or load to subassembly products such as soldered printed circuit board in case handling or transporting. 7

9 Package Dimensions of Reel Dimensions of Taping P P0 D0 T E D W F degree Max. C N W degree Max. P K W Murata Part Number MM R MM R TOLERNSE 78 0 ±.0 ±0.5 C ±0.8 D ±0.5 N (min.) Dia. 50 Dia. 50 W.5.5 ±.5 W (max.) ±0. P0 4±0..4±0. P 8±0. W ±0. P ±0. D0 Dia T 0.±0.05 E.75±0. F 5.5±0. K.0±0.5 Minimum Quantity MM R: 80 mm dia. reel/000 pcs. MM R: 0 mm dia. reel/000 pcs. MM : ulk /free 8

10 Microwave Coaxial Connectors GSC type Features. The mating height is only mm maximum by new mechanical design. Suitable for low profile design.. Receptacle size is.0x.0mm. Suitable high density. New mating mechanical desigh makes stable feeling connection. 4. High performance with wide frequency range (DC to 6GHz). V.S.W.R. at DC to GHz is. maximum. V.S.W.R. at GHz to 6GHz is. maximum. 5. Surface mountable and reflow solderable. 6. Tape package available. MM ±0.0.6 ø. (R0.5).6 0.5±0.0 (R0.5).5 0.± ±0. ø± ±0. Hot Terminal Ground Terminal Tolerances Unless Otherwise Specified: ±0. pplications Portable telephone, cordless telephone(analog and digital), GPS, and other microwave radio and measurement equipment. Part Number Rated Voltage (V) MM Contact Resistance (ohm) 0.05 max. Withstanding Voltage (rms) Insulation Durability Resistance (M ohm) (cycles) Frequency Rating (GHz) Temperature Range (degree C) 00 (C) 500 min. 00 DC ~+90 VSWR Center Contact Outer Contact Insulator. max. (DC~6GHz) Copper lloy Gold plated Copper lloy Silver plated Engineering plastic Impedance : 50 ohm MXTK Profile Dimensions ø ±0.5 Tolerances unless otherwise specified : ±0..8max. max. 0.7min. Measurement Probe Dimensions (for Receptacle) MM470 (Hand measurement) MM47 (utomatic measurement) SM-JCK SM-JCK ø5. ø.55 ø ø4.6 ø5. ø5. ø4.06 ø5. ø6.5 Continued on the following page. 9

11 Continued from the preceding page. Measurement Probe Dimensions (for Cable ssembly) Cable Length Tolerance MM480 L.4 SM-JCK ø ø ø. Cable Length L (mm) ( ) Over Till Dimensional tolerance (mm) ± ± ± % of L 0% of L L must be 0mm Min. Disengagement Tool (Part Number: M00) (C) (Dia. 8) 5± 7.95± 0.5±0.6 45±.±0.6.9±0.6 Land Pattern Dimensions ø (-ø0.6) (Through Holes) (.7) (.5) (.74) (.5) Land Electrode 0

12 Notice Notice (Storage and Operation Condition). Environment Conditions () This product is designed for use of electrical equipment in the environment (temperature, humidity, atmospheric pressure and etc.) specified in this approval drawing: it may not be used in the following environments or under the following conditions : (a) mbient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, mmonia gas, Sulfuric acid gas, Nitric oxie gas, etc.) (b) mbient air containing volatile or combustible gas. (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles. (e) In direct sunlight (f) Other environments similar to the above conditions. () Contact the manufacturer before using the product in any of the above environments or under any of the above conditions.. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use, if the product has been stored for more than 6 months. Temperature : -0 to +40 degree C Humidity : 5 to 85 % RH

13 Notice Notice (Soldering and Mounting). Reflow soldering Soldering must be carried out without exceeding the allow able soldering temperature and time shown within the shaded area of FIGURE "llowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in FIGURE "llowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in FIGURE "Reflow Soldering Standard Conditions". Use the Pattern and Metal mask pattern is illustrated in details. There is the possibility at receptacle to solder-joint with some gap in between PC by the excess solder. llowable Temperature and Time Reflow Soldering Temperature (degreec) Time (sec.) Solder : Sn60% - Pb40% Reflow Soldering Standard Conditions. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 50 degree C Time 60 to 0 s. Soldering Temperature (at the tip of the soldering iron) less than 50 degree C Time less than s. Temperature (degreec) Pre-heating 50±0 degreec Peak temperature 5±5 degreec Time (sec.) 0 sec. max.. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering sec sec. Measuring point of temperature : In-Out Terminals of Device Reflow Soldering : oth Convection and Infrared Rays : Hot ir : Hot Plate 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. 5. Please note the following in case of soldering terminals or leads of the product. () Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.0wt%). () Flux should be cleaned thoroughly. 6. Please mount this product at the position so that stress by wrap and/or bend of the PC may not apply to it. 7. Please dry out this product immediately after soldering and cleaning. Continued on the following page.

14 Notice Continued from the preceding page. Notice (Handling). Usage Condition () Do not apply electrical voltage greater than specified in the drawing. It might because of degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. () Confirm that there are not any influence to the product's performance which might because by other components which touch with the product. () Please contact the manufacturer before hand, if the product is to be used in frequently bent position.. Handling () Do not apply excessive shock or load to subassembly like soldered printed circuit board in case of handling and transporting it. () Do not try to pull the cable, when a connector with a coaxial cable is handled. () Disregard with following notes could give mechanical damage and/or poor electrical performance.. Handling Instructions () This cable is just only fit with MM receptacle. ny other receptable can not be used with this cable. () Disengagement: Use tool P/N M00. Do not try to pull out by the cable, because there is the possibility a wire breaks. () Do not give a twisted torque to the cable and connector. (4) Mechancical stress: The stress to the connector should be limited as shown the following Figure. (a) Stress to the housing. Stress and : 4.9N Max. (b) Stress to the outer sleeve. Stress C:.94N Max. Stress D:.96N Max. (c) Cable pull strength. Stress E: 4.9N Max. Figure. Mechanical stress after engagement C E D

15 Package Dimensions of Reel Dimensions of Taping P P0 D0 T E D W F degree Max. C N W degree Max. P K W Murata Part Number MM99-700R MM99-700R5 TOLERNSE 78 0 ±.0 ±0.5 C ±0.8 D ±0.5 N (min.) Dia. 50 Dia. 50 W.5.5 ±.5 W (max.) ±0. P0 4±0..8±0. P 8±0. W ±0. P ±0. D0 Dia T 0.±0.05 E.75±0. F 5.5±0. K.5±0.5 Minimum Quantity MM99-700R: 80 mm dia. reel/000 pcs. MM99-700R5: 0 mm dia. reel/5000 pcs. MM : ulk /free 4

16 Microwave Coaxial Connectors FSC type.4 Features. High engagement with new structure (50% up compared with ESC type). Ultra-miniature (LxWxH:.4x.4x.5mm) for High density mounting.. Ultra-low plofile (.0mm max.). 4. SMD and reflow soldering applicable. 5. Tapping package applicable. 6. Mountable by automatic placer. 7. High performance. (V.S.W.R.. max. at GHz) 8. Matched with ultra-thin FEP coaxial cables (0.8mm dia). pplications Portable telephone, mobile telephone, cordless telephone, GPS, and other microwave radio and mesurement equipment. MM MM max () Hot Terminal Ground Terminal Tolerances Unless Otherwise Specified:± () 0.max ().5 : Hot Terminal : Ground Terminal TOLERNCES UNLESS OTHERWISE SPECIFIED : ±0. Part Number Rated Voltage (V) MM Contact Resistance (ohm) 0.05 max. Withstanding Voltage (rms) Insulation Durability Resistance (M ohm) (cycles) Frequency Rating (GHz) Temperature Range (degree C) 00 (C) 500 min. 50 DC ~+90. max. VSWR Center Contact Outer Contact Insulator Copper lloy Gold plated Copper lloy Gold plated Engineering plastic MM max. 00 (C) 500 min. 50 DC ~+90. max. Copper lloy Gold plated Copper lloy Gold plated Engineering plastic Impedance : 50 ohm MXFG Profile Dimensions ø..4 max..4 Profile.8 Tolerances Unless Otherwise Specified:±0. 4. min Clearanse for mating Continued on the following page. 5

17 Continued from the preceding page. Measurement Probe Dimensions for Receptacle MM454 (For FSC type receptacle) for Cable ssembly MM460 (For FSC type cable assembly) SM-JCK SM-JCK ø.6.5 ø5. ø5. ø5. ø. ø5. Land Pattern Dimensions MM ø0.6 MM ø (.5) (.74) (.5).57 Land Electrode (Note) Please design I/O pattern so that the impedance matches 50 ohm including the land pattern. The material of P.C.. is the epoxy resin of glass fabric base. (εr=4.8)thickness is.0mm. The solder resist should be printed except for the land pattern on the P.C (.5) (.74) (.5) 0. Land Electrode Cable Length Tolerance L Over L must be 40mm Min. Cable Length L(mm)( ) Till Dimensional tolerance(mm) ± ± 4 ±0 +% of L 0% of L Continued on the following page. 6

18 Continued from the preceding page. Disengagement Tool M9000 (for MM79-700) How to use tool (for MM79-700) 5±0.6 ø.7t 0± 5± ±0.6 5± ±0.6 45±.5±0.6 M9004 (for MM79-70) How to use tool (for MM79-70) (05) M9004 () (0) 7

19 Notice Notice (Storage and Operation Condition). Environment Conditions () This product is designed for use of electrical equipment in the environment (temperature, humidity, atmospheric pressure and etc.) specified in this approval drawing: it may not be used in the following environments or under the following conditions : (a) mbient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, mmonia gas, Sulfuric acid gas, Nitric oxie gas, etc.) (b) mbient air containing volatile or combustible gas. (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles. (e) In direct sunlight (f) Other environments similar to the above conditions. () Contact the manufacturer before using the product in any of the above environments or under any of the above conditions.. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use, if the product has been stored for more than 6 months. Temperature : -0 to +40 degree C Humidity : 5 to 85 % RH 8

20 Notice Notice (Soldering and Mounting). Reflow soldering Soldering must be carried out without exceeding the allow able soldering temperature and time shown within the shaded area of FIGURE "llowable Temperature and Time of Reflow Soldering". In case the soldering is repeated, the maximum time in FIGURE "llowable Temperature and Time of Reflow Soldering" should be accumulated time. The standard soldering conditions are shown in FIGURE "Reflow Soldering Standard Conditions". Use the Pattern and Metal mask pattern is illustrated in details. There is the possibility at receptacle to solder-joint with some gap in between PC by the excess solder. llowable Temperature and Time Reflow Soldering Temperature (degreec) Time (sec.) Solder : Sn60% - Pb40% Reflow Soldering Standard Conditions. Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 50 degree C Time 60 to 0 s. Soldering Temperature (at the tip of the soldering iron) less than 50 degree C Time less than s. Temperature (degreec) Pre-heating 50±0 degreec Peak temperature 5±5 degreec Time (sec.) 0 sec. max.. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering sec sec. Measuring point of temperature : In-Out Terminals of Device Reflow Soldering : oth Convection and Infrared Rays : Hot ir : Hot Plate 4. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. 5. Please note the following in case of soldering terminals or leads of the product. () Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.0wt%). () Flux should be cleaned thoroughly. 6. Please mount this product at the position so that stress by wrap and/or bend of the PC may not apply to it. 7. Please dry out this product immediately after soldering and cleaning. Continued on the following page. 9

21 Notice Continued from the preceding page. Notice (Handling). Usage Condition () Do not apply electrical voltage greater than specified in the drawing. It might because of degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. () Confirm that there are not any influence to the product's performance which might because by other components which touch with the product. () Please contact the manufacturer before hand, if the product is to be used in frequently bent position.. Handling () Do not apply excessive shock or load to subassembly like soldered printed circuit board in case of handling and transporting it. () Do not try to pull the cable, when a connector with a coaxial cable is handled. () Disregard with following notes could give mechanical damage and/or poor electrical performance.. Handling Instructions () This cable is just only fit with MM and MM79-70 receptacle. ny other receptable can not be used with this cable. () Disengagement: Use tool P/N M9000 (for MM79-700) or M9004 (for MM79-70). Do not try to pull out by the cable, because there is the possibility a wire breaks. () Do not give a twisted torque to the cable and connector. (4) Mechancical stress: The stress to the connector should be limited as shown the following Figure. (a) Stress to the housing. Stress and : 4.9N Max. (b) Stress to the outer sleeve. Stress C:.94N Max. Stress D:.96N Max. (c) Cable pull strength. Stress E: 7.84N Max. (for MM79-700) 4.9N Max. (for MM79-70) Figure. Mechanical stress after engagement (MM79-700) D C (MM79-70) E D C E 0

22 Package Dimensions of Reel MM79-700R/R4 MM79-70R/R D W D W N N C C W W Murata Part Number MM79-700R MM79-700R4 TOLERNSE 78 0 ±.0 ±0.5 C ±0.8 D ±0.5 N (min.) Dia. 50 Dia. 50 W.5.5 ±.5 W (max.) Murata Part Number MM79-70R MM79-70R TOLERNSE 78 0 ±.0 ±0.5 C ±0.8 D ±0.5 N (min.) Dia. 50 Dia. 50 W.5.5 ±.5 W (max.) Dimensions of Taping P P0 D T W F E P K.9±0..7±0. W ±0. D ø E.75±0. F 5.5±0. K ±0.5 P0 4±0. P 8±0. P ±0. T 0.±0.05 Minimum Quantity MM79-700R: 80 mm dia. reel/000 pcs. MM79-700R4: 0 mm dia. reel/4000 pcs. MM : ulk /free MM79-70R: 80 mm dia. reel/ 500 pcs. MM79-70R: 0 mm dia. reel/000 pcs. MM79-70 : ulk /free

23 Microwave Coaxial Connectors F type Features. Ultra-miniature and low profile. (6.mm max.). High performance (V.S.W.R.. max. at 4GHz). Very resonable price for commercial applications. 4. Cable assembly applicable. 5. Low RF leakage. 6. vailable for ultra-thin coaxial cables. φ.58±0.5 (.5) ±0.4.5±0. (6.5).75± ±0.5 ±0. 4 pplications Portable telephones, mobile telephones, cordless telephones, oscilloscope, GPS, and any other R.F. circuits for microwave equipment. MM5-505 MM5-507 (0.5) φ0.5±0. ottom view (6.5).5±0. ±0.4 ø6.5±0.4 ø.58±0.5 (.5) ø0.5±0. ±0..75± ± ±0. (0.5) MM6-506 ø.58±0.5 (6.9) 5±0. ± ±0. ø0.5±0. ±0.(Points) Part Number Rated Voltage (V) MM Contact Resistance (ohm) 0.0 max. Withstanding Voltage (rms) Insulation Durability Resistance (M ohm) (cycles) Frequency Rating (GHz) Temperature Range (degree C) 00 (C) 000 min. 50 DC ~+90. max. VSWR Center Contact Outer Contact Insulator eryllium copper or rass Gold plated Phosper bronze Poly-phenylene Sulfide Silver/Nickel plated MM max. 00 (C) 000 min. 50 DC ~+90. max. eryllium copper or rass Gold plated Phosper bronze Poly-phenylene Sulfide Silver/Nickel plated MM max. 00 (C) 000 min. 50 DC ~+90. max. eryllium copper or rass Gold plated Phosper bronze Poly-phenylene Sulfide Silver/Nickel plated Impedance : 50 ohm

24 MXYH Profile Dimensions 5max. 8.±0.5 Profile 6.mm max. (5.5) Clearanca 8.5mm min. Coaxial cable Coaxial cable (ø.4) Printed circuit Printed circuit Profile Clearance for matling Measurement Probe Dimensions for Receptacle MM5 (For F type receptacle) MM7 (For F type receptacle) (8).5±0.85 (8) (5) HEX8 4 F-FEMLE SM-JCK F-FEMLE SM-PLUG ø4.7±0. ø4.7±0. 5±0.5 5±0.5 for Cable ssembly MM60 (For F type cable assembly) 8.6±0.4 MM80 (For F type cable assembly) (.5) HEX8 F-MLE SM-JCK F-MLE SM-PLUG Mounting Dimensions -ø.±0. MM5-505/507 Cable Length Tolerance L (.75).5±0. ø0.7±0.05 CLE LENGTH TOLERNCE Cable length L (mm) Over Till L must be 50mm Min. Dimensional tolerance(mm) ± ±4 ±0 + 0 %of L Continued on the following page.

25 Continued from the preceding page. Disengagement Tool P/N : M6000 (.) ().4±0.5 (6.) 4.5± ±0. (4) (6) (.) (ø) P/N : M600.9±0..±0. (45) (5) (6) 0.85±0. (.5) (ø) () 4 4

26 Notice Notice (Storage and Operation Condition). Environment Conditions () This product is designed for use of electrical equipment in the environment (temperature, humidity, atmospheric pressure and etc.) specified in this approval drawing: it may not be used in the following environments or under the following conditions : (a) mbient air containing corrosive gas (Chlorine gas, Hydrogen sulfide gas, mmonia gas, Sulfuric acid gas, Nitric oxie gas, etc.) (b) mbient air containing volatile or combustible gas. (c) In liquid (water, oil, chemical solution, organic solvents, etc.) (d) In environments with a high concentration of airborne particles. (e) In direct sunlight (f) Other environments similar to the above conditions. () Contact the manufacturer before using the product in any of the above environments or under any of the above conditions.. Storage Store in manufacturer's package or tightly re-closed box with the following conditions. Use this product within 6 months after receipt. Check the terminal solderability before use, if the product has been stored for more than 6 months. Temperature : -0 to +40 degree C Humidity : 5 to 85 % RH 4 Notice (Soldering and Mounting). Soldering by soldering iron Soldering by soldering iron should be carried out in accordance to the following conditions. Pre-heating Temperature 50 degree C Time 60 to 0 s. Soldering Temperature (at the tip of the soldering iron) less then 50 degree C Time less than s.. We cannot warrant against mishaps caused by any use of this product that deviates from allowable temperature and time of reflow soldering.. In soldering, do not apply excessive mechanical force to terminals or leads greater than specified in the drawing. 4. Please note the following in case of soldering terminals or leads of the product. () Use Rosin based flux, but not with strong acid flux (Chlorine content should be less than 0.0wt%) () Flux should be cleaned thoroughly. 5. Please mount this product at the position so that stress by wrap and/or bend of the PC may not apply to it. 6. Please dry out this product immediately after soldering and cleaning. Notice (Handling). Usage Condition () Do not apply electrical voltage greater than specified in the drawing. It might because of degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. () Confirm that there are not any influence to the product's performance which might because by the other components which touch with the product.. Handling () Do not apply excessive shock or load to subassembly like soldered printed circuit board in case of handling and transporting it. () This receptacle is just only fit with F tape cable assembly. ny other cable can not be used with this receptacle. 5

27 Notice Notice (Handling). Usage Condition () Do not apply electrical voltage greater than specified in the drawing. It might because of degradation or destruction of the product. Even if it endures during a short time, long time qualification is not guaranteed. () Confirm that there are not any influence to the product's performance which might because by other components which touch with the product. 4. Handling () Do not apply excessive shock or load to subassembly like soldered printed circuit board in case of handling and transporting it. () Do not try to pull the cable, when a connector with a coaxial cable is handled. () Disregard with fllowing notes could give mechanical damage and/or poor electrical performance.. Handling Instructions () This cable is just only fit with MM5-505, MM5-507 and MM6-506 receptacle. ny other receptable can not be used with this cable. () Disengagement: Use tool P/N M6000 or M600. Do not try to pull out by the cable, because there is the possibility a wire breaks. () Do not give a twisted torque to the cable and connector. (4) Mechancical stress: The stress to the connector should be limited as shown the following Figure. (a) Stress to the housing. Stress : 9.8N Max. (b) Stress to the outer sleeve. Stress : 4.9N Max. Stress C:.94N Max. (c) Cable pull strength. Stress D: 9.8N Max. Figure. Mechanical stress after engagement F right angle plug connector D C MM

28 Miniaturized Microwave Coaxial Connector Cable List Murata cable code 0.8D double shield Cross linked polyethylene cable 6 0.8D single shield Cross linked polyethylene cable 6 0.8D double shield FEP cable D single shield FEP cable 76 Inner conductor Material No. and Dia. Total Dia. - (No./mm) (mm) copper covered steel wire / copper covered steel wire / Silver coated copper covered steel wire / Silver coated copper covered steel wire / Material - Cross linked polyethylene compound Cross linked polyethylene compound FEP FEP Insulator Melting point (Reference only) Degree C Outer conductor Total Dia. Material Dia. of wire Total Dia. (mm) - (mm) (mm) 0.8 are copper wire 0. Inner. Outer are copper wire Tin plated copper wire 0.05 Inner.05 Outer. 0.8 Tin plated copper wire Material - Polyvinyl chloride compound Polyvinyl chloride compound FEP FEP Sheath Nominal thickness (mm) Color Overall Dia. Minimum bending radius Nominal impedance Continuous operating voltage Nominal static capacitance Nominal Insertion loss d/m at GHz d/m at GHz d/m at GHz d/m at 4GHz - (mm) (mm) (Ohm) (pf/m) Gray Vrms max Gray Vrms max Gray Vrms max Gray Vrms max d/m at 6GHz ssembly to F Suitable Suitable Suitable Not Suitable ssembly to FSC Not Suitable Not Suitable Not Suitable Suitable ssembly to GSC Not Suitable Not Suitable Not Suitable Not Suitable 7

29 Miniaturized Microwave Coaxial Connector Cable List 0.4D single shield FEP cable 0.4D single shield PF cable 0.4D single shield PF cable Murata cable code Inner conductor Material No. and Dia. Total Dia. - (No./mm) (mm) Silver coated copper covered alloy wire 7/ Silver coated copper covered steel wire / Silver coated copper covered alloy wire 7/ Material - FEP PF PF Insulator Melting point (Reference only) Degree C Total Dia. (mm) Outer conductor Material Dia. of wire Total Dia. - (mm) (mm) Tin plated copper wire Tin plated copper wire Tin plated copper wire Material - FEP PF PF Sheath Nominal thickness (mm) Color - White White White Overall Dia. (mm) Minimum bending radius (mm) Nominal impedance (Ohm) Continuous operating voltage 00 Vrms max. 00 Vrms max. 00 Vrms max. Nominal static capacitance (pf/m) d/m at GHz Nominal Insertion loss d/m at GHz d/m at GHz d/m at 4GHz d/m at 6GHz ssembly to F ssembly to FSC ssembly to GSC Not Suitable Suitable Suitable Not Suitable Suitable Suitable Not Suitable Suitable Suitable 8

30 !Note Please read rating and!cution (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc. O0E4.pdf This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering. Note:. Export Control <For customers outside Japan> Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons. <For customers in Japan> For products which are controlled items subject to the Foreign Exchange and Foreign Trade Law of Japan, the export license specified by the law is required for export.. Please contact our sales representatives or product engineers before using our products listed in this catalog for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property, or when intending to use one of our products for other applications than specified in this catalog. q ircraft equipment w erospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment!0 pplication of similar complexity and/or reliability requirements to the applications listed in the above. Product specifications in this catalog are as of January 00. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read rating and CUTION (for storage and operating, rating, soldering and mounting, handling) in this catalog to prevent smoking and/or burning, etc. 5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification before ordering. 6. Please read CUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product specification or to transact the approval sheet for product specification, before ordering. 7. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or third party's intellectual property rights and other related rights in consideration of your using our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 8. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. Head Office -6-0, Tenjin Nagaokakyo-shi, Kyoto , Japan Phone: International Division -9-, Shibuya, Shibuya-ku, Tokyo , Japan Phone: Fax: intl@murata.co.jp