6-CHANNEL LIGHT EFFECT LED DRIVER
|
|
- Juliana Collins
- 6 years ago
- Views:
Transcription
1 -CHANNEL LIGHT EFFECT LED DRIVER DESCRIPTION ISFL/ISFLA is a -channel light effect LED driver which features two-dimensional auto breathing mode and an audio modulated display mode. It has One Shot Programming Mode and PWM Control Mode for RGB lighting effects. The maximum output current can be adjusted in levels (ma~ma). FEATURES Supply voltage range from.v to.v Two groups RGB, single color LED breathing system-free pre-established pattern independently controlled automatic and semiautomatic breathing system-free pre-established pattern independently controlled outputs of PWM steps levels programmable output current Audio mode with AGC function Cascade for the synchronization of chips QFN- (mm mm) package QUICK START PROCEDURE The ISFL/ISFLA evaluation board is fully assembled and tested. Follow the steps listed below to verify board operation. Caution: Do not turn on the power supply until all connections are completed. ) Short JP to connect by board MCU. ) Connect the VDC power to the connector (TP&TP). ) Turn on the power supply/plug in the Micro USB Pay attention to the supply current. If the current exceeds A, please check for circuit fault. EVALUATION BOARD OPERATION The ISFL/ISFLA evaluation board has five display modes. Press K to switch configurations. ) lamps breathe at the same time ) The RGB monochromatic breathes ) RGB audio mode ) lamps breathe one by one ) lamps audio mode Note: ISFL/ISFLA solely controls the FxLED function on the evaluation board. Figure : Photo of ISFL/ISFLA Evaluation Board RECOMMENDED EQUIPMENT.V, A power supply ABSOLUTE MAXIMUM RATINGS.V power supply Caution: Do not exceed the conditions listed above, otherwise the board will be damaged. SOFTWARE CONTROL J default setting is closed (short). If it is set to open, the MCU's,, and CLK pin will be high impedance (open-drain) and external control is allowed. Follow the steps listed below for external control. ) Open J to enable external control ) Pull-up the to. ) Connect the VDC power to the connector (TP&TP). ) Turn on the power supply/plug in the Micro USB Pay attention to the supply current. If the current exceeds A, please check for circuit fault. ) Start external IIC control. Caution: If J is closed (shorted), user can t connect the user s MCU, otherwise the user s MCU (maybe.v) will connect to evaluation bard s MCU (.V) and maybe damaged. Please refer to the datasheet to get more information about ISFL/ISFLA. Integrated Silicon Solution, Inc. Rev. B, //
2 -CHANNEL LIGHT EFFECT LED DRIVER ORDERING INFORMATION Part No. Temperature Range Package ISFL-QFLS-EB - C ~ + C (Industrial) QFN-, Lead-free ISFLA-QFLS-EB - C ~ + C (Industrial) QFN-, Lead-free Table : Ordering Information For pricing, delivery, and ordering information, please contacts ISSI s analog marketing team at analog@issi.com or () -. V R K R K V U VBAT _ PC-ANTI_TAMP VSS_ PC-OSC_IN PB/TIM_CH PC-OSC_OUT PB/TIM_CH OSC_IN BOOT OSC_IN OSC_OUT PB/IC_/TIM_CH OSC_OUT NRST PB/IC_/TIM_CH VSSA PB A PB/JNTRST PA-WKUP/ADC_IN/TIM_CH_ETR PB/JTDO CLK/V_BM PA/ADC_IN/TIM_CH PA/JTDI PA/USART_TX/ADC_IN/TIM_CH PA/JTCK/SWCLK EN PA/USART_RX/ADC_IN/TIM_CH _ PA/SPI_NSS/ADC_IN VSS_ PA/SPI_SCK/ADC_IN PA/JTMS/SWDIO PA/SPI_MISO/ADC_IN/TIM_CH PA/CANTX/USBDP/TIM_ETR PA/SPI_MOSI/ADC_IN/TIM_CH PA/CANRX/USBDM/TIM_CH KEY PB/ADC_IN/TIM_CH PA/USART_RX/TIM_CH PB/ADC_IN/TIM_CH PA/USART_TX/TIM_CH PB/BOOT PA/TIM_CH/MCO BIT PB/IC_/USART_TX PB/SPI_MOSI/TIM_CHN BIT PB/IC_/USART_RX PB/SPI_MISO/TIM_CHN VSS_ PB/SPI_SCK/TIM_CHN _ PB/SPI_NSS/TIM_BKIN STMFCT V CLK V DIO V R K V R.K CLK/V_BM Audio In C.uF C uf R.K C.uF C uf R K R.K R R IN I_AUD REXT CFILT CLKV_BM IN I_AUD R_EXT C_FILT AD ISFL U OUT OUT OUT OUT OUT OUT OUT OUT OUT LD LD LD LD LD LD G R G R B B RGB RGB V TP TP R R R R.K D DFL OSC_OUT OSC_IN Y M C uf C P C P Micro USB R C uf NC Con U C uf R K SD U LDO R K VOUT BP BIT BIT U S S G G BP APM C nf D D D D V C uf CON AUDIO IN TP SCl CLK/V_BM I_AUD.V DIO CLK Audio In C.uF R K U BP Bypass IN+ C uf AV IN ISAP R K K MODE OUT+ IN- OUT- R K C uf JP OPEN=EXT CTRL EN OUTB OUTA CON SPK Speaker Figure : ISFL/ISFLA Application Schematic Integrated Silicon Solution, Inc. Rev. B, //
3 -CHANNEL LIGHT EFFECT LED DRIVER BILL OF MATERIALS Name Symbol Description Qty Supplier Part No. LED Driver U Matrix LED Driver ISSI ISFL/ ISFLA LDO U.V LDO SGMICRO SGM-.YNG MCU U Microcontroller STM STMFCT PMOS U PMOS ANPEC APM AMP U Audio power amplifier ISSI ISAP LED LD~LD Blue LED,SMD Everlight -/BHC-ZLMRY/T LED RGB,RGB RGB LED,SMD Everlight -/RGBC/TR Diode D Diode,SMD Diodes In DFLS Crystal Y Crystal,MHz HLX HC-S Resistor R,R RES,R,/W,±%,SMD Yageo RCJR-RL Resistor R RES,.k,/W,±%,SMD Yageo RCJR-KL Resistor R,R,R, R,R RES,k,/W,±%,SMD Yageo RCJR-KL Resistor R RES,R,/W,±%,SMD Yageo RCJR-KL Resistor R RES,k,/W,±%,SMD Yageo RCJR-KL Resistor R RES,k,/W,±%,SMD Yageo RCJR-KL Resistor R,R,R RES,.k,/W,±%,SMD Yageo RCJR-KL Resistor R RES,k,/W,±%,SMD Yageo RCJR-KL Resistor R RES,k,/W,±%,SMD Yageo RCJR-KL Capacitor C,C CAP,µF,V,±%,SMD Yageo CCKKXRBB Capacitor C,C,C, C,C CAP,µF,V,±%,SMD Yageo CCKKXRBB Capacitor C CAP,nF,V,±%,SMD Yageo CCKKXRBB Capacitor C,C CAP,pF,V,±%,SMD Yageo CCKKXRBB Capacitor C,C CAP,.µF,V,±%,SMD Yageo CCKKXRBB Capacitor C,C CAP,.µF,V,±%,SMD Yageo CCKKXRBB Button K Button SMD Bill of Materials, refer to Figure above. Integrated Silicon Solution, Inc. Rev. B, //
4 -CHANNEL LIGHT EFFECT LED DRIVER Integrated Silicon Solution, Inc. Rev. B, // Figure : Board Component Placement Guide - Top Layer Figure : Board PCB Layout - Top Layer
5 -CHANNEL LIGHT EFFECT LED DRIVER Figure : Board Component Placement Guide - Bottom Layer Figure : Board PCB Layout - Bottom Layer Copyright Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. Rev. B, //
6-CHANNEL LIGHT EFFECT LED DRIVER
-CHANNEL LIGHT EFFECT LED DRIVER DESCRIPTION ISFLA is a -channel light effect LED driver which features two-dimensional auto breathing mode and an audio modulated display mode. It has One Shot Programming
More information9-CHANNEL LIGHT EFFECT LED DRIVER
DESCRIPTION ISFL is a -channel light effect LED driver which features two-dimensional auto breathing mode and an audio modulated display mode. It has One Shot Programming mode and PWM Control mode for
More information36 CHANNELS LED DRIVER EVALUATION BOARD GUIDE
CHANNELS LED DRIVER EVALUATION BOARD GUIDE DESCRIPTION ISFL is an LED driver with constant current channels. Each channel can be pulse width modulated (PWM) by bits for smooth LED brightness control. In
More informationProcedure. IS31FL3236-QFLS2-EB QFN-44, Lead-free IS31FL3236A-QFLS2-EB QFN-44, Lead-free. Table1: Ordering Information
Channels LED Driver Evaluation Board Guide Description ISFL/ISFLA is comprised of constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel
More information24-RGB MATRIX LED DRIVER
-RGB MATRIX LED DRIVER DESCRIPTION The ISFLA is a general purpose n (n=~) LED Matrix programmed via MHz IC compatible interface. Each LED can be dimmed individually with -bit PWM data and -bit DC scaling
More information18 11 DOTS MATRIX LED DRIVER
DOTS MATRIX LED DRIVER DESCRIPTION The ISFLA is a general purpose n (n=~) LED Matrix programmed via MHz IC compatible interface. Each LED can be dimmed individually with -bit PWM data and -bit DC scaling
More information18 CHANNELS LED DRIVER EVALUATION BOARD GUIDE
8 CHANNELS LED DRIVER EVALUATION BOARD GUIDE DESCRIPTION ISFL8 is comprised of 8 constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel
More information36 CHANNELS LED DRIVER EVALUATION BOARD GUIDE
CHANNELS LED DRIVER EVALUATION BOARD GUIDE DESCRIPTION ISFLA is comprised of constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel can
More informationIS31AP4913 3D AND BASS ENHANCE STEREO HEADPHONE DRIVER EVALUATION BOARD GUIDE
ISAP D AND BASS ENHAE STEREO HEADPHONE DESCRIPTION The ISAP evaluation board is a fully assembled and tested PCB. The ISAP is a high quality stereo headphone driver with D and bass enhance designed to
More information28 CHANNELS LED DRIVER EVALUATION BOARD GUIDE
CHANNELS LED DRIVER EVALUATION BOARD GUIDE DESCRIPTION ISFLA is comprised of constant current channels each with independent PWM control, designed for driving LEDs, PWM frequency can be khz or khz. The
More informationIS31BL3230-QFLS2-EB QFN-16, Lead-free. Table1: Ordering Information
IS3BL33 8 Channels Constant Current LED Driver Description The IS3BL33 provides eight regulated current sources; each delivers up to 4mA of load current with careful selection of external sense resistors,
More informationIS31BL3506B 1.0MHZ BOOST CONVERTER WITH 35V INTERNAL MOSFET SWITCH
ISBL0B.0MHZ BOOST CONVERTER WITH V INTERNAL MOSFET SWITCH DESCRIPTION ISBL0B is a boost converter featuring an integrated MOSFET switch designed for driving series strings of LED or other device. Input
More informationIS31AP2036A HIGH EFFICIENCY, CLASS-K AUDIO POWER AMPLIFIER WITH INTEGRATED CHARGE PUMP CONVERTER
IS3AP036A HIGH EFFICIENCY, CLASS-K AUDIO POWER AMPLIFIER DESCRIPTION The IS3AP036A is a Class-K audio power amplifier with high efficiency and automatic gain control. It drives up to.0w (0% THD+N) into
More informationIS31LT3178/IS32LT TO-200mA CONSTANT-CURRENT LED DRIVER
IS3LT378/IS3LT378 -TO-mA DESCRIPTION The IS3LT378 and IS3LT378 are adjustable linear current devices with excellent temperature stability. A single resistor is all that is required to set the operating
More informationIS32BL3556 WIDE INPUT VOLTAGE RANGE, HIGH EFFICIENCY FAULT TOLERANT LED DRIVER
ISBL6 WIDE INPUT VOLTAGE RANGE, HIGH EFFICIENCY DESCRIPTION RECOMMENDED EQUIPMENT The ISBL6 is a white LED driver for backlight applications based on a highly efficient boost controller operating over
More information3 4 MATRIX LED DRIVER
DESCRIPTION The ISFL is a general purpose LEDs matrix driver with / cycle rate. The device can be programmed via an IC compatible interface. Each LED can be dimmed individually with -bit PWM data which
More informationIS32LT3172/73 10-TO-200MA CONSTANT-CURRENT LED DRIVER
DESCRIPTION The IS32LT3172/73 is adjustable constant current linear devices with excellent temperature stability. A single resistor is all that is required to set the operating current from 10mA to 200mA.
More informationIS31LT V, 350MA, 4-CHANNEL CONSTANT CURRENT REGULATOR WITH OTP
DESCRIPTION The IS31LT3117 is a 4-channel, linear regulated, constant current LED driver which can sink 4 equal currents of up to 350mA per channel to drive high brightness LEDs over an input voltage range
More informationIS31LT3948 GENERAL DEMO BOARD GUIDE
IS3LT3948 GENERAL DEMO BOARD GUIDE DESCRIPTION IS3LT3948 is a PFM step-up DC-DC converter designed for driving the white LED arrays for large size LCD panel backlighting applications. With internal OVP
More information6x8 MATRIX LED DRIVER
x MATRIX LED DRIVER DESCRIPTION The ISFL is an automotive grade general purpose LEDs matrix driver with / cycle rate. The device can be programmed via an IC compatible interface. Each LED can be dimmed
More informationIS31LT3360 AIC DEMO BOARD GUIDE
DESCRIPTION The ISLT6 is a continuous mode inductive step-down converter, designed for driving a single LED or multiple series connected efficiently from a voltage source higher than the LED voltage. The
More informationIS32LT3175N/P SINGLE CHANNEL LINEAR LED DRIVER WITH FADE IN/FADE OUT AND PWM DIMMING
DESCRIPTION The ISLT is a single channel linear programmable current regulator capable of up to ma. It integrates a debounce and latch circuit on the channel enable pin (EN) to facilitate the use of a
More informationIS32LT3120 Dual Channel Linear LED Driver With Fade In/Fade Out
ISLT Dual Channel Linear LED Driver With Fade In/Fade Out DESCRIPTION The ISLT is a linear programmable current regulator consisting of output channels capable of up to ma each. Each channel features an
More informationIS31LT3954_IS32LT3954 DEMO BOARD GUIDE
DESCRIPTION The IS31LT3954_IS32LT3954 is a DC-to-DC switching converter, which integrate an N-channel MOSFET to operate in a buck configuration. The device supply a wide input voltage between 4.5V and
More informationIS31LT3953_IS32LT3953 DEMO BOARD GUIDE
DESCRIPTION The IS31LT3953_IS32LT3953 is a DC-to-DC switching converter, which integrate an N-channel MOSFET to operate in a buck configuration. The device supply a wide input voltage between 4.5V and
More informationIS32LT V, 350MA, 4-CHANNEL CONSTANT CURRENT REGULATOR WITH OTP FOR AUTOMOTIVE LIGHT
DESCRPTON The S32LT3117 is designed for automotive lighting applications such as map light, dome light, tail light and daytime running lights. This device is a 4-channel, linear regulated, constant current
More informationIS31FL CHANNEL LIGHT EFFECT LED DRIVER. November 2017
6-CHANNEL LIGHT EFFECT LED DRIVER November 2017 GENERAL DESCRIPTION IS31FL3196 is a 6-channel light effect LED driver which features two-dimensional auto breathing mode and an audio modulated display mode.
More informationDescription. Quick Start. Features. Ordering Information. Applications. or call
Description LED PAR IS31LT3932 is a universal LED driver, which can operate in fly-back, buck-boost and buck convertor. For isolation fly-back, it can achieve high PF, high current accuracy, ± 5 % load
More informationIS31FL3236A 36-CHANNEL LED DRIVER; SELECTABLE PWM FREQUENCY IS31FL3236A. February 2018
36-CHANNEL LED DRIVER; SELECTABLE PWM FREQUENCY February 2018 GENERAL DESCRIPTION IS31FL3236A is comprised of 36 constant current channels each with independent PWM control, designed for driving LEDs,
More informationIS31FL BIT COLOR LED DRIVER WITH PWM CONTROL June 2013
16-BIT COLOR LED DRIVER WITH PWM CONTROL June 2013 GENERAL DESCRIPTION The IS31FL3726 is comprised of constant-current drivers designed for color LEDs. The output current value can be set using an external
More informationIS31FL3190 IS31FL CHANNEL FUN LED DRIVER. Preliminary Information November 2015
1-CHANNEL FUN LED DRIVER GENERAL DESCRIPTION IS31FL3190 is a 1-channel fun LED driver which has One Shot Programming mode and PWM Control mode for LED lighting effects. The maximum output current can be
More informationIS31FL CHANNEL FUN LED DRIVER July 2015
1-CHANNEL FUN LED DRIVER July 2015 GENERAL DESCRIPTION IS31FL3191 is a 1-channel fun LED driver which has One Shot Programming mode and PWM Control mode for LED lighting effects. The maximum output current
More information7 OUT1 8 OUT2 9 OUT3 10 OUT4 11 OUT5 12 OUT6 13 OUT7 14 OUT8 15 OUT9 16 OUT10 17 OUT11 18 OUT12 19 OUT13 20 OUT14 21 OUT15 22 OUT16 OUT17 23 OUT18
18 CHANNELS LED DRIVER June 2017 GENERAL DESCRIPTION IS31FL3218 is comprised of 18 constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel
More informationIS31FL CHANNELS LED DRIVER. February 2018
36 CHANNELS LED DRIVER GENERAL DESCRIPTION IS31FL3236 is comprised of 36 constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel can be
More informationIS31FL3209 IS31FL CHANNELS LED DRIVER; 1/24 DC SCALING WHITE BALANCE. December 2017
18 CHANNELS LED DRIVER; 1/24 DC SCALING WHITE BALANCE December 2017 GENERAL DESCRIPTION IS31FL3209 is comprised of 18 constant current channels each with independent PWM control, designed for driving LEDs,
More informationIS31FL3206 IS31FL CHANNEL LED DRIVER; SELECTABLE PWM FREQUENCY. Preliminary Information May 2018
12-CHANNEL LED DRIVER; SELECTABLE PWM FREQUENCY Preliminary Information May 2018 GENERAL DESCRIPTION IS31FL3206 is comprised of 12 constant current channels each with independent PWM control, designed
More informationIS31FL3726 IS31FL CHANNEL COLOR LED DRIVER. June 2018
16-CHANNEL COLOR LED DRIVER GENERAL DESCRIPTION The IS31FL3726 is comprised of constant-current drivers designed for color LEDs. The output current value can be set using an external resistor. The output
More informationIS31FL3235A 28 CHANNELS LED DRIVER. February 2017
28 CHANNELS LED DRIVER GENERAL DESCRIPTION is comprised of 28 constant current channels each with independent PWM control, designed for driving LEDs, PWM frequency can be 3kHz or 22kHz. The output current
More informationIS31PW MHZ BOOST CONVERTER WITH 30V INTERNAL FET SWITCH February 2012 GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION CIRCUIT
1.1MHZ BOOST CONVERTER WITH 30V INTERNAL FET SWITCH February 2012 GENERAL DESCRIPTION FEATURES The is a constant current step-up converter. The step-up converter topology allows series connection of the
More informationIS31FL3208A 18-CHANNEL LED DRIVER; SELECTABLE PWM FREQUENCY. August 2018
18-CHANNEL LED DRIVER; SELECTABLE PWM FREQUENCY August 2018 GENERAL DESCRIPTION is comprised of 18 constant current channels each with independent PWM control, designed for driving LEDs, PWM frequency
More informationIS31AP4066D DUAL 1.3W STEREO AUDIO AMPLIFIER. January 2014 KEY SPECIFICATIONS
DUAL 1.3W STEREO AUDIO AMPLIFIER GENERAL DESCRIPTION The IS31AP4066D is a dual bridge-connected audio power amplifier which, when connected to a 5V supply, will deliver 1.3W to an 8Ω load. The IS31AP4066D
More information7 OUT1 8 OUT2 9 OUT3 10 OUT4 11 OUT5 12 OUT6 13 OUT7 14 OUT8 15 OUT9 16 OUT10 17 OUT11 18 OUT12 19 OUT13 20 OUT14 21 OUT15 22 OUT16 OUT17 23 OUT18
18 CHANNELS LED DRIVER GENERAL DESCRIPTION is comprised of 18 constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel can be set at up
More informationFigure 1 Typical Application Circuit
STEREO HEADPHONE DRIVER January 206 GENERAL DESCRIPTION The IS3AP492 is stereo headphone drivers designed to allow the removal of the output DC-blocking capacitors for reduced component count and cost.
More informationIS31FL3731 AUDIO MODULATED MATRIX LED DRIVER. May 2013
AUDIO MODULATED MATRIX LED DRIVER May 2013 GENERAL DESCRIPTION The IS31FL3731 is a compact LED driver for 144 single LEDs. The device can be programmed via an I2C compatible interface. The IS31FL3731 offers
More informationVDD 0.1 F A1 C1 IN+ IS31AP2145A IN- CTRL GND. Figure 1 Typical Application Circuit (Differential Input)
2.9W@5.0V MONO CLIP-LESS & FILTER-LESS CLASS-D AUDIO POWER AMPLIFIER GENERAL DESCRIPTION The IS3AP245A is a 2.9W@5.0V mono, clip-less, filter-less, high efficiency Class-D audio power amplifier with automatic
More informationFigure 1 Typical Application Circuit. Figure 2 Application Circuit for Less Than 4 LEDs
FOUR CHANNEL CONSTANT CURRENT LED DRIVER June 2014 GENERAL DESCRIPTION The IS31BL3212 provides four regulated current sources, delivers up to 23mA of load current to accommodate four white LEDs. It requires
More informationPAM2841EV1 User Guide 1.5A SW CURRENT, 40V PRECISION WLED DRIVER
General Description The PAM2841 is a step-up current mode LED Driver. The PAM2841 supports a range of input voltages from 2.5V to 5.5V, allowing the use of a single Li+/Li- polymer cell, 3AA cell battery,
More informationIS31AP W AUDIO POWER AMPLIFIER WITH ACTIVE-LOW STANDBY MODE. October 2012
.W AUDIO POWER AMPLIFIER WITH ACTIVE-LOW STANDBY MODE October 0 GENERAL DESCRIPTION The IS3AP499 has been designed for demanding audio applications such as mobile phones and permits the reduction of the
More informationThe Design Of Embedded PV Inverter Grid-Connected System
Advanced Materials Research Online: 0-- ISSN: -9, Vols. 0-09, pp -9 doi:0.0/www.scientific.net/amr.0-09. 0 Trans Tech Publications, Switzerland The Design Of Embedded PV Inverter Grid-Connected System
More informationSeptember 2009 Rev FEATURES EN 1. L1 10uH. CZ2 2700pF. RZ2 8.06k D1 CMSH3-40MA. Fig. 1: XRP7657 Evaluation Board Schematics
September 009 Rev..0.0 GENERAL DESCRIPTION The is a non synchronous voltage mode PWM step down (buck) regulator capable of a constant output current up to Amps. A wide 4.75V to 5V input voltage range allows
More informationFxLED & Backlight LED Driver Selection
FxLED & Backlight LED Driver Selection Graphical Selector Guide Audio Modulate Shift Register Gamma Correction Auto Breath Charge Pump Eval Board IS31FL3726 16-Channel LED, 60mA QFN-24 FxLED Driver IS31FL3199
More informationUHF RFID Micro Reader Reference Design Hardware Description
Application Micro Note Reader Reference Design AS399x UHF RFID Reader ICs UHF RFID Micro Reader Reference Design Hardware Description Top View RF Part Bottom View RF Part www.austriamicrosystems.com/rfid
More informationIS31AP W AUDIO POWER AMPLIFIER WITH ACTIVE-HIGH STANDBY MODE. August 2013
.W AUDIO POWER AMPLIFIER WITH ACTIVE-HIGH STANDBY MODE August 03 GENERAL DESCRIPTION The IS3AP4996 has been designed for demanding audio applications such as mobile phones and permits the reduction of
More informationPVIN. EN RLIM 2.49k. RON 8.87k. Test Point BST BST PVIN PVIN PVIN 59 PVIN PVIN PVIN 56 PVIN 62 TON 68 AGND 67 BST PAD ILIM 65 PVIN PAD EN/MODE 66
December 04 GENERAL DESCRIPTION The XR795 is a 5A synchronous step-down Power Module for point-of load supplies. A wide 5V to V input voltage range allows for single supply operation from industry standard
More informationIS31AP4833 TREBLE AND BASS CONTROL WITH 3D ENHANCEMENT AUDIO POWER DRIVER. March 2014
TREBLE AND BASS CONTROL WITH 3D ENHANCEMENT AUDIO POWER DRIVER March 204 GENERAL DESCRIPTION The IS3AP4833 is a treble and bass control with 3D enhancement audio power driver. The IS3AP4833 provides tone
More informationPVIN. Test Point uF. RLIM 2k. RON 12.1k EN/MODE 70 ILIM 69 SS 74 BST BST BST PAD PVIN 65 PVIN 59 PVIN 60 PVIN 66 PVIN 61 PVIN 62 PVIN 63
May 05 GENERAL DESCRIPTION The XR790 is a 0A synchronous step-down Power Module for point-of load supplies. A wide 4.5V to V input voltage range allows for single supply operation from industry standard
More informationIS31LT3932 HIGH PF LOW THD UNIVERSAL LED DRIVER. December 2013
HIGH PF LOW THD UNIVERSAL LED DRIVER GENERAL DESCRIPTION IS31LT3932 is a universal LED driver, which can operate in fly-back, buck-boost and buck convertor. For isolation fly-back, it can achieve high
More informationAugust 2011 Rev FEATURES. Fig. 1: XRP7618 Evaluation Board Schematics
August 2011 Rev. 2.2.0 GENERAL DESCRIPTION The is an 8-channel, high voltage, constant-current sink LED driver capable of sinking up to 100mA current per channel. With outputs rated at 30V, the can control
More informationRT8129AGQW Evaluation Board
High Efficiency Single Synchronous Buck PWM Controller Purpose The RT8129A integrates a Constant-On-Time (COT) PWM controller and MOSFET driver so that the external circuit is easily designed and the components
More informationAAN-5 Demo Kit Drives VGA Over 300m of CAT5
AAN-5 Demo Kit Drives VGA Over 300m of CAT5 Introduction Due to its low cost, wide availability and predictable electrical characteristics, standard un-shielded CAT5 twisted-pair interconnect is a good
More informationReference Board User s Manual for SiC6xx
DESCRIPTION Reference Board User s Manual for This manual is good for all DrMOS products with MLP5x5-3L footprints and Vishay part list show-in as below, SiC60CD-T-GE3, SiC60ACD-T-GE3, SiC60RCD-T-GE3,
More informationIX Evaluation Board User s Guide INTEGRATED CIRCUITS DIVISION. 1. Introduction. 1.1 Features:
IX844 Evaluation Board User s Guide. Introduction IXYS Integrated Circuits Division's IX844 evaluation board contains all the necessary circuitry to demonstrate the features of a high voltage gate driver
More informationAN4781 Application note
Application note STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H Introduction The STEVAL-IFP028V1 is an evaluation board designed to analyze all IPS160H functionality. It is designed
More informationNovember 2013 Rev VIN FDMS7578. L1 IHLP-5050FD-01 41A, 1mOhm. Csnub 0 Ohm FDMS7650DC. 0 Ohm. 6.8nF. CFF 0.56nF
XRP64 November 0 Rev..0.0 GENERAL DESCRIPTION The XRP64 is a synchronous step-down controller for point-of load supplies up to 5A. A wide 4.5V to V input voltage range allows for single supply operation
More informationOUT1 OUT2 OUT3 OUT4 IS31FL3237 OUT34 OUT35 OUT36. Figure 1 Typical Application Circuit
36-CHANNEL LED DRIVER GENERAL DESCRIPTION IS31FL3237 is an LED driver with 36 constant current channels. Each channel can be pulse width modulated (PWM) by 16 bits for smooth LED brightness control. In
More informationFigure 1 Constant current white LED driver using PWM at the EN pin to control intensity
1.0MHZ BOOST CONVERTER WITH 35V INTERNAL MOSFET SWITCH April 2013 GENERAL DESCRIPTION IS31BL3506B is a boost converter featuring an integrated MOSFET switch designed for driving series strings of LED or
More informationEvaluation Board: Synchronous Buck Converter Integrated FET
ROHM Switching Regulator Solutions Evaluation Board: Synchronous Buck Converter Integrated FET BU90002GWZEVK-101 (3.3V 1A Output) No.000000000 Introduction This application note will provide the steps
More informationAVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL
AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL Document : AVL-10000T Version: 1.00 Author: Henry S Date: 25 July 2008 This module contains protection circuitry to guard against damage due to
More informationIS31LT3916. Isolated or Non-isolated configuration LED driver with active PFC. January General Description. Features
Isolated or Non-isolated configuration LED driver with active PFC General Description Features January 2013 The IS31LT3916 is a primary side, peak current mode, isolated or non-isolated type HBLED driver.
More informationIS32LT3117 PRELIMINARY 60V, 350MA, 4-CHANNEL CONSTANT CURRENT REGULATOR WITH OTP
PRELIMINARY 60V, 350MA, 4-CHANNEL CONSTANT CURRENT REGULATOR WITH OTP GENERAL DESCRIPTION The IS32LT3117 is a 4-channel, linear regulated, constant current LED driver which can provide 4 equal currents
More informationEVQ8616-L-6-00A. High Efficiency, 6A, 6V Synchronous Step-down Converter Evaluation Board FEATURES DESCRIPTION ELECTRICAL SPECIFICATION APPLICATIONS
The Future of Analog IC Technology EVQ8616-L-6-00A High Efficiency, 6A, 6V Synchronous Step-down Converter Evaluation Board DESCRIPTION The EVQ8616-L-6-00A is an evaluation board for the MPQ8616GL-6, a
More information155Mbps Fiber-Optic PIN Pre-Amplifier with AG
155Mbps Fiber-Optic PIN Pre-Amplifier with AG GENERAL DESCRIPTION The is a trans-impedance amplifier with A GC for 155Mbps fiber channel applications. The A GC function allows -39dB to +3dB input dynamic
More informationEvaluates: MAXM V Output-Voltage Application. MAXM17552 Evaluation Kit. General Description. Quick Start. Features. Recommended Equipment
Click here for production status of specific part numbers. General Description The MAXM17552 evaluation kit (EV kit) is a demonstration circuit of the MAXM17552 ultra-small, high efficiency, current mode,
More informationNovember 2012 Rev FEATURES Ohm/ 1%/ 0805/ 0.25W RSET ISEN 3 VREF GND PAD. RT 10k TH 5 LX 8. Fig. 1: XRP7613 Evaluation Board Schematics
0 PAD t November 2012 Rev. 1.0.0 GENERAL DESCRIPTION The Exar Evaluation board (EVB) is a fully assembled and tested surface-mount PCB that demonstrates the LED driver. The is a non-synchronous step-down
More informationMLX83100 Automotive DC Pre-Driver EVB83100 for Brushed DC Applications with MLX83100
EVB83100 for Brushed DC Applications with MLX83100 Stefan Poels JULY 17, 2017 VAT BE 0435.604.729 Transportstraat 1 3980 Tessenderlo Phone: +32 13 67 07 95 Mobile: +32 491 15 74 18 Fax: +32 13 67 07 70
More informationIS31AP W STEREO CLASS-D AUDIO AMPLIFIER WITH POWER LIMIT AND DYNAMIC TEMPERATURE CONTROL November 2015
W STEREO CLASS-D AUDIO AMPLIFIER WITH POWER LIMIT AND DYNAMIC TEMPERATURE CONTROL November 5 GENERAL DESCRIPTION The IS3AP20 is a high efficiency stereo Class-D audio amplifier with adjustable power limit
More informationAugust 2014 Rev FEATURES CC1. CC nf. RC k. Fig. 1: XRP76XX Evaluation Board Schematics
XRP7664-65-74-75 2A/3A 8V Synchronous Step-Down Regulator, Constant frequency August 204 Rev. 2.0.0 GENERAL DESCRIPTION The EXAR XRP76XX Evaluation kit is a fully assembled and tested surface-mount PCB
More informationSupertex inc. HV748DB1 HV748 ±75V 1.25A Ultrasound Pulser Demoboard
HV78DB HV78 ±75V.5A Ultrasound Pulser Demoboard Introduction The HV78 is a monolithic -channel, high speed, high voltage, ultrasound transmitter pulser. This integrated, high performance circuit is in
More informationRT9465 Evaluation Board
3A Single Cell Li-Ion Battery Slave Switching Charger Purpose The is a switch-mode single cell li-ion/li-polymer battery charger for portable applications. It intergrates a synchronous PWM controller,
More information1A 1.5MHz PFM/PWM Synchronous Step-Down Converter. January 2014 Rev FEATURES. Fig. 1: XRP6658 Application Diagram
January 2014 Rev. 1.6.0 GENERAL DESCRIPTION The XRP6658 is a synchronous current mode PWM step down (buck) converter capable of delivering up to 1 Amp of current and optimized for portable battery-operated
More informationCS6A4689 Stereo Headphone Amplifier Evaluation Board (Rev 1)
User Manual CS6A4689 Stereo Headphone Amplifier Evaluation Board (Rev 1) Features and Key Specification Supply Voltage ±5V ~ ±11V Audio In ±0.6V (max.) @ ±11V Stereo Output Power 4W RMS per channel General
More informationAN BGA GHz 16 db gain CATV amplifier. Document information. Keywords. BGA3021, Evaluation board, CATV, Medium Power.
Rev. 1 16 September 2014 Application note Document information Info Keywords Abstract Content BGA3021, Evaluation board, CATV, Medium Power This application note describes the schematic and layout requirements
More information16 Channels LED Driver
16 Channels LED Driver Description The SN3216 is a fun light LED controller with an audio modulation mode. It can store data of 8 frames with internal RAM to play small animations automatically. SN3216
More informationZICM35xSPx Hardware Design Guidelines
Application Note 0011-00-16-09-000 ZICM35xSPx Hardware Design Guidelines Document No: 0011-00-16-09-000 (Issue C) INTRODUCTION This Application Note provides module placement, schematic design examples
More informationIS31FL3746A 24-RGB MATRIX LED DRIVER. Preliminary Information September 2018
24-RGB MATRIX LED DRIVER Preliminary Information September 2018 GENERAL DESCRIPTION The IS31FL3746A is a general purpose 18 n (n=1~4) LED Matrix programmed via 1MHz I2C compatible interface. Each LED can
More informationEV2633-R-00A Full Power Management IC For Single-Cell Battery System
The Future of Analog IC Technology EV2633-R-00A Full Power Management IC For Single-Cell Battery System DESCRIPTION The EV2633-R-00A is the evaluation board designed to demonstrate the capabilities of
More informationFEBFL7701_L30U003A. 2.4 W LED Ballast Using FL7701. Featured Fairchild Product: FL7701
User Guide for FEBFL7701_L30U003A 2.4 W LED Ballast Using FL7701 Featured Fairchild Product: FL7701 Direct questions or comments about this evaluation board to: Worldwide Direct Support Fairchild Semiconductor.com
More informationEVM3805-QB-01A 6V, 0.6A Synchronous Step-Down Switcher Evaluation Board
EVM3805-QB-01A 6V, 0.6A Synchronous Step-Down Switcher Evaluation Board DESCRIPTION The EVM3805-QB-01A is used for demonstrating the performance of MPS s MPM3805 a low voltage high switching frequency
More informationCS MBPS GBPS Post Amplifier and LD Driver FEATURES
155MBPS - 1.25GBPS Post Amplifier and LD Driver CS6718 GENERAL DESCRIPTION CS6718 integrated two main functions in a single chip providing optimal solutions for various fiber module applications. The functional
More informationGENERAL DESCRIPTION. FEATURES 3A step-down power module
XR7903 April 06 GENERAL DESCRIPTION The XR7903 is part of a family of 40V synchronous step-down power modules combining the controller, drivers, inductor, passive components and MOSFETs in a single package
More informationUser s Manual ISL71218MEVAL1Z. User s Manual: Evaluation Board. High Reliability Space
User s Manual ISL71218MEVAL1Z User s Manual: Evaluation Board High Reliability Space Rev. Aug 217 USER S MANUAL ISL71218MEVAL1Z Evaluation Board UG139 Rev.. 1. Overview The ISL71218MEVAL1Z evaluation platform
More informationEvaluates: MAX17544 in 5V Output-Voltage Application. MAX V Output Evaluation Kit. General Description. Features.
MAX7544 5V Output Evaluation Kit Evaluates: MAX7544 in General Description The MAX7544 5V output evaluation kit (EV kit) provides a proven design to evaluate the MAX7544 high-voltage, high-efficiency,
More informationAL9910AEV1 User Guide Universal High Voltage LED Driver
General Description This demonstration board utilizes the AL9910A high voltage PWM LED Buck controller providing a cost effective solution for offline high brightness LED applications. This user-friendly
More informationPurpose. Table of Contents. Purpose Introduction General Product Information Key Performance Summary Table... 3
Purpose The RT8295A is a high-efficiency current mode synchronous step-down regulator that can deliver up to 2A output current from a wide input voltage range of 4.5V to 23V. This document explains the
More informationUM1589 User manual. M24LR-Discovery kit user guide. Introduction
UM589 User manual M4LR-Discovery kit user guide Introduction The M4LR-Discovery kit helps you evaluate the M4LRXX-E Dual Interface EEPROM that features an energy harvesting analog output, as well as a
More informationEvaluation Board Manual
Evaluation Board Manual SP7600 FEATURES Wide Input Voltage Range 4.5V 29V 2 Amps Max Continuous Output Current Internal Compensation Input Feedforward Control improves Transient Response and Regulation
More informationNovember 2011 Rev FEATURES. Fig. 1: SP2526A Application Diagram Two Port Self Powered Hub
November 2011 Rev. 2.1.0 GENERAL DESCRIPTION The SP2526A device is a dual +3.0V to +5.5V USB Supervisory Power Control Switch ideal for self-powered and bus-powered Universal Serial Bus (USB) applications.
More informationFigure 1: AAT2469/AAT2499 Evaluation Board Picture.
Introduction EVALUATION BOARD DATA SHEET The AAT246/AAT24 evaluation board is a hardware platform to evaluate the functions of the AAT246 and AAT24 devices. The AAT246 is a dedicated TVLite TM control
More information1.25Gbps Fiber-Optic Pre-Amplifier
1.25Gbps Fiber-Optic Pre-Amplifier CS6720 GENERAL DESCRIPTION CS6720 is a low noise trans-impedance amplifier designed for 1.25Gbps fiber optical applications. In typical applications, it is connected
More informationSTEVAL-IHM042V1: low voltage dual motor control board based on the STM32F303 MCU and L6230 monolithic driver. Figure 1.
User manual STEVAL-IHM0V: low voltage dual motor control board based on the STMF0 MCU and L60 monolithic driver Introduction The STEVAL-IHM0V evaluation board is designed as a dual motor field-oriented
More information