Reference Board User s Manual for SiC6xx
|
|
- Beatrice Thornton
- 5 years ago
- Views:
Transcription
1 DESCRIPTION Reference Board User s Manual for This manual is good for all DrMOS products with MLP5x5-3L footprints and Vishay part list show-in as below, SiC60CD-T-GE3, SiC60ACD-T-GE3, SiC60RCD-T-GE3, SiC60ARCD-T-GE3 SiC63CD-T-GE3, SiC63CD-T-GE3, SiC634CD-T-GE3 This reference board (Fig. ) allows the end user to evaluate the family devices for their features and functionalities. It can also be a reference design for a user s application. Fig. - MLP5x5-3L Reference Board CONNECTION AND SIGNAL / TEST POINTS Power Sockets J7 - V IN (see device datasheet for V IN range) J8 - V OUT J9, J0 - Power Ground Signal and Test Leads PIN # NAME FUNCTION TP V IN INPUT voltage measurement pin TP Ground Ground pin for INPUT voltage measurement TP3 V OUT OUTPUT voltage measurement pin TP4 Ground Ground pin for OUTPUT voltage measurement J V CIN Supply voltage for internal logic circuitry J V DRV Supply voltage for internal gate driver J3 ZCD_EN# ZCD_EN# is LOW, diode emulation is allowed. When ZCD_EN# is HIGH, continuous conduction mode is forced. ZCD_EN# can also be put in a high impedance mode by floating the pin. J4 PWM PWM input logic J5 GL Low-side MOSFET gate signal J6 LX Switch node of the power stage J3 GH High-side MOSFET gate signal J4 PHASE Return path of high-side gate driver J5 DSBL# Disable pin. Active low J6 THWn Thermal warning open drain output Revision: 08-Nov-7 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
2 OPERATION. Enable the device: jump DISBL# leads.. Connect logic and drive voltage: set a power supply output voltage to 5 V and connect it to J (V DRV ) pins. Since R is populated, J (V CIN ) is shorted to J (V DRV ) pins. 3. To power J (V CIN ) and J (V DRV ) pins seperately with two different power supplies, make sure R is removed to avoid short between power supplies. 4. Connect PWM signal: preset a waveform or function generator with desired amplitude, frequency and duty cycle, and connect it to J4 (PWM). As an example, for V to.8 V; 500 khz operating condition, the function generator can be set to pulse mode with 500 khz frequency; 300 ns on time, 0 V to 5 V amplitude (0 V to 3.3 V for A version). By increasing or decreasing on time, corresponding duty cycle will vary. 5. Connect input power supply with desired voltage to J7 (V IN+ ) and J0 (P ) sockets. Now the system should be up running. If diode emulation mode is wanted, connect ZCD_EN# (J3) with external control signal. If OTP trip point is to be checked, monitor J6 (THWn) by either connecting it to a volt meter or probing it on oscilloscope. Change Output Voltage If different output voltage is needed, then simply turn the PWM duty cycle up or down. PCB LAYOUT Top Revision: 08-Nov-7 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
3 Inner Layer Inner Layer Revision: 08-Nov-7 3 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
4 Inner Layer 3 Inner Layer 4 Revision: 08-Nov-7 4 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
5 Bottom SCHEMATIC J VCIN VCIN J7 J0 +C4 C/NC +C5 C/00U C/0uF/35V C6 C/0uF/35V C7 J3 C/0uF/35V GH J4 C8 PHASE C/0uF/35V C9 C/0uF/35V C0 TP C/0uF/35V TP C C/0n R8 R/400K C8 R6 R/NC C C/NC P P P P R4 R/R PHASE PHASE 7 GH BOOT 6 GH 5 BOOT C C/00n 4 C U U/SiC60CD C C/U VCIN 3 VCIN R R/R ZCD_EN# ZCD_EN# PWM 3 PWM LX C TP3 C3 C4 C5 C6 C7 C8 C9 C0 C C/470uF C/uF C/uF C/uF C/uF C/uF C/uF C/uF C/uF + DSBL# THWn VDRV P GL R R/0 3 DSBL# THWn VDRV GL L INDUCTOR L INDUCTOR R3 R/0 VDRV C3 C/U R5 R/400K J VOUT VDRV 3 J3 ZCD_EN# J4 PWM J5 GL R7 R/0K VOUT J8 J5 DSBL# J6 THWn C C3 C4 C5 C6 C7 C/uF C/uF C/uF C/uF C/uF C/uF TP4 J6 LX Revision: 08-Nov-7 5 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
6 BILL OF MATERIALS ITEM QUANTITY DESIGNATOR DESCRIPTION FOOTPRINT COMMENT PART NUMBER VENDER C, C3 Capacitor C-0603 C / V CC0603KRX7R5BB05 Yageo C Capacitor C-0603 C / 00 nf AC0603KRX7R7BB04 Yageo 3 C4 Capacitor C-HS8-3.5 C / NC ND 4 C5 Capacitor C-Case-D C / 00 V T49X07K05ZT Kemet 5 6 C6, C7, C8, C9, C0, C Capacitor C-06 C / 0 μf / 35 V GMK36AB706KL- TR Taiyo Yuden 6 C Capacitor C-0805 C / NC ND 7 C3 Capacitor C-Case-D C / 470 μf EEF-SX0E33ER Panasonic 8 4 C4, C5, C6, C7, C8, C9, C0, C, C, C3, C4, C5, C6, C7 Capacitor C-0805 C / μf CC0805KKX5R5BB6 Yageo 9 C8 Capacitor C-0603 C / 0 nf AC0603KRX7R9BB03 Yageo 0 L Inductor L-4040 TBD FP007R-R7-R Copper Bussmann R, R4 Resistor R-0603 R /. Generic R, R3 Resistor R-0603 R / 0 Generic 3 R5, R8 Resistor R-0603 R / 400 k Generic 4 R6 Resistor R-0805 R / NC ND 5 R7 Resistor R-0603 R / 0 k Generic 6 U DrMOS 5 x 5 MLP55-3L Vishay Revision: 08-Nov-7 6 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
High Performance DrMOS Integrated Power Stage
High Performance DrMOS Integrated Power Stage SiC778A DESCRIPTION The SiC778 is an integrated power stage solution optimized for synchronous buck applications offering high current, high efficiency and
More informationFEATURES APPLICATIONS V IN. Gate driver. Fig. 1 - SiC620R and SiC620AR Typical Application Diagram
60 A VRPower Integrated Power Stage DESCRIPTION The SiC620R and SiC620AR are integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high
More informationFEATURES APPLICATIONS V IN. Gate driver. Fig. 1 - SiC632 and SiC632A Typical Application Diagram
50 A VRPower Integrated Power Stage DESCRIPTION The SiC632 and SiC632A are integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high
More informationFEATURES APPLICATIONS VIN. Gate driver. Fig. 1 - SiC531 and SiC531A Typical Application Diagram
0 A VRPower Integrated Power Stage DESCRIPTION The SiC and SiCA are integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high power density
More informationVRPower Integrated Power Stage Solution
VISHAY SILICONIX www.vishay.com Power IC By Ron Vinsant VRPower products are integrated power stage solutions optimized for highperformance synchronous buck applications. These devices offer high power
More informationFEATURES APPLICATIONS VIN. Gate driver. Fig. 1 - SiC521 and SiC521A Typical Application Diagram
0 A VRPower Integrated Power Stage DESCRIPTION The SiC and SiCA are integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high power density
More informationZSPM8060-KIT Evaluation Board Description
Restrictions: IDT s ZSPM8060-KIT Open-Loop Evaluation Board is designed for evaluation of the ZSPM9060, laboratory setup, and module development only. The Evaluation Board must not be used for module production
More informationFDMF6824B Extra-Small, High-Performance, High-Frequency DrMOS Module
January 2014 FDMF6824B Extra-Small, High-Performance, High-Frequency DrMOS Module Benefits Ultra-Compact 6x6 mm PQFN, 72% Space-Saving Compared to Conventional Discrete Solutions Fully Optimized System
More informationFDMF6708N Extra-Small, High-Performance, High-Frequency DrMOS Module
FDMF6708N Extra-Small, High-Performance, High-Frequency DrMOS Module Benefits Ultra-Compact 6x6 mm PQFN, 72% Space-Saving Compared to Conventional Discrete Solutions Fully Optimized System Efficiency Clean
More informationFEATURES APPLICATIONS VIN. Gate driver. Fig. 1 - SiC621 Typical Application Diagram
60 A VRPower Integrated Power Stage DESCRIPTION The is integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high power density performance.
More informationFDMF6823C Extra-Small, High-Performance, High-Frequency DrMOS Module
FDMF6823C Extra-Small, High-Performance, High-Frequency DrMOS Module Benefits Ultra-Compact 6x6 mm PQFN, 72% Space-Saving Compared to Conventional Discrete Solutions Fully Optimized System Efficiency Clean
More informationIntegrated DrMOS Power Stage
Integrated DrMOS Power Stage DESCRIPTION The SiC762CD is an integrated solution that contains PWM optimized n-channel MOSFETs (high side and low side) and a full featured MOSFET driver IC. The device complies
More informationIntegrated DrMOS Power Stage
Integrated DrMOS Power Stage DESCRIPTION The SiC769CD is an integrated solution that contains optimized n-channel MOSFETs (high side and low side) and a full featured MOSFET driver IC. The device complies
More informationFEATURES APPLICATIONS VIN. Gate driver. Fig. 1 - SiC631 Typical Application Diagram
50 A VRPower Integrated Power Stage DESCRIPTION The is integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high power density performance.
More informationFEATURES APPLICATIONS. Gate driver P GND. Fig. 1 - SiC533 Typical Application Diagram
A VRPower Integrated Power Stage DESCRIPTION The is an integrated power stage solution optimized for synchronous buck applications to offer high current, high efficiency, and high power density performance.
More informationFDMF6705B - Extra-Small, High-Performance, High- Frequency DrMOS Module
April 2013 FDMF6705B - Extra-Small, High-Performance, High- Frequency DrMOS Module Benefits Ultra-Compact 6x6 mm PQFN, 72% Space-Saving Compared to Conventional Discrete Solutions Fully Optimized System
More informationFDMF6707B - Extra-Small, High-Performance, High- Frequency DrMOS Module
March 2012 FDMF6707B - Extra-Small, High-Performance, High- Frequency DrMOS Module Benefits Ultra-Compact 6x6mm PQFN, 72% Space-Saving Compared to Conventional Discrete Solutions Fully Optimized System
More informationFEATURES APPLICATIONS VIN. Gate driver. Fig. 1 - SiC631 Typical Application Diagram
50 A VRPower Integrated Power Stage DESCRIPTION The is integrated power stage solutions optimized for synchronous buck applications to offer high current, high efficiency, and high power density performance.
More informationDemo Board User Manual for SiP12109 (4 A) and SiP12110 (6 A), 4.5 V to 15 V Input Synchronous Buck Regulators
SiP209DB, SiP20DB Demo Board User Manual for SiP209 (4 A) and SiP20 (6 A), 4.5 V to 5 V Input Synchronous Buck Regulators THE CHIP PRODUCT SUMMARY SiP209DMP-T-GE4 Input Voltage Range 4.5 V to 5 V Output
More informationEvaluation Board Manual
SiP3249EVB, SiP32429EVB Evaluation Board Manual DESCRIPTION SiP3249EVB and SiP32429EVB are a load switch that integrates multiple control features that simplify the design and increase the reliability
More informationQuad Channel Monolithic Power Stage
V DRV2 VZ 2 www.vishay.com Quad Channel Monolithic Power Stage DESCRIPTION The is a quad channel, fully-integrated monolithic power stage optimized for multi-phase synchronous buck applications. The part
More informationZSPM9010. Ultra-Compact, High-Performance DrMOS Device. Datasheet. Brief Description. Features. Available Support. Physical Characteristics.
Ultra-Compact, High-Performance DrMOS Device ZSPM9010 Datasheet Brief Description The ZSPM9010 DrMOS is a fully optimized, ultracompact, integrated MOSFET plus driver power stage solution for high-current,
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationZSPM8010-KIT User Guide
Restrictions: IDT s ZSPM800-KIT Open-Loop Evaluation Board is designed for evaluation of the ZSPM900, laboratory setup, and module development only. The Evaluation Board must not be used for module production
More informationRT6207AHGQUF Evaluation Board
5A, 18V, 650kHz, ACOT Synchronous Step-Down Converter Purpose The RT6207AH is a Advanced Constant On-Time (ACOT ) control architecture step-down converter with the input voltage range from 4.5V to 18V
More informationRT8130BGQW Evaluation Board
RT830BGQW V High Efficiency Synchronous Buck PWM Controller Purpose The RT830B is a high efficiency single phase synchronous Buck DC/DC controller with 5V/V supply voltage. This document explains the function
More informationEvaluates: MAX17544 in 5V Output-Voltage Application. MAX V Output Evaluation Kit. General Description. Features.
MAX7544 5V Output Evaluation Kit Evaluates: MAX7544 in General Description The MAX7544 5V output evaluation kit (EV kit) provides a proven design to evaluate the MAX7544 high-voltage, high-efficiency,
More informationZSPM9000. Ultra-Compact, High-Performance DrMOS Device. Datasheet. Brief Description. Features. Available Support. Physical Characteristics.
Ultra-Compact, High-Performance DrMOS Device ZSPM9000 Datasheet Brief Description The ZSPM9000 DrMOS is a fully optimized, ultracompact, integrated MOSFET plus driver powerstage solution for high-current,
More informationGenerating Isolated Supplies for Industrial Applications Using the SiC462 in an Isolated Buck Topology
VISHAY SILICONIX www.vishay.com ICs By Ron Vinsant INTRODUCTION Industrial power applications typically require a high input voltage. Standard voltage rails are 4 V, 36 V, and 48 V. The DC/DC step-down
More informationPurpose. Table of Contents. Purpose Introduction General Product Information Key Performance Summary Table... 3
Purpose The RT8295A is a high-efficiency current mode synchronous step-down regulator that can deliver up to 2A output current from a wide input voltage range of 4.5V to 23V. This document explains the
More informationRT8129AGQW Evaluation Board
High Efficiency Single Synchronous Buck PWM Controller Purpose The RT8129A integrates a Constant-On-Time (COT) PWM controller and MOSFET driver so that the external circuit is easily designed and the components
More informationFEBFAN23SV04T_LVA Evaluation Board. High-Efficiency Synchronous Buck Converter for DDR Termination. Featured Product: FAN23SV04T
User Guide for FEBFANSV0T_LVA Evaluation Board High-Efficiency Synchronous Buck Converter for DDR Termination Featured Product: FANSV0T Direct questions or comments about this evaluation board to: Worldwide
More informationAOZ5166QI-01. High-Current, High-Performance DrMOS Power Module AOZ5166QI-01. Features. General Description. Applications. Typical Application Circuit
High-Current, High-Performance DrMOS Power Module General Description The AOZ5166QI-01 is a high efficiency synchronous buck power stage module consisting of two asymmetrical MOSFETs and an integrated
More informationHigh Efficiency DC-DC Converter Module
Design Note DN05109/D High Efficiency DC-DC Converter Module Device Application Input Voltage Output Power Topology I/O Isolation NCP12700 Module 18 to 160 Vdc Up to 15 W DCM Flyback Isolated Output Specification
More informationAOZ A DrMOS Power Module AOZ5066. Features. General Description. Applications. Typical Application Circuit
60A DrMOS Power Module General Description The AOZ5066 is a high efficiency synchronous buck power stage module consisting of two asymmetrical MOSFETs and an integrated driver. The MOSFETs are individually
More informationEvaluates: MAX MAX17016 Evaluation Kit. General Description. Features. Ordering Information. Component List
General Description The MAX706 evaluation kit (EV kit) demonstrates the standard 0A application circuit of the MAX706. This DC-DC converter steps down high-voltage batteries to generate low-voltage core
More informationSYNCHRONOUS BUCK CONVERTER LX1918 EVALUATION BOARD
SYNCHRONOUS BUCK CONVERTER LX1918 EVALUATION BOARD INTEGRATED PRODUCTS Page 1 TABLE OF CONTENTS LX1918 EVAL Introduction...3 Schematic for LX1918 Evaluation Board... 4 Hook Up... 5 Connections... 6 Bill
More informationCPC9909EB. Hi-Brightness, Off-Line LED Driver Evaluation Board User s Guide INTEGRATED CIRCUITS DIVISION
CPC9909EB Hi-Brightness, Off-Line LED Driver Evaluation Board User s Guide Specifications Parameter Min Typ Max Unit Input Voltage AC - - 265 V rms DC 15-375 V DC Load Current - - 350 ma Efficiency - 90
More informationHigh Efficiency DC-DC Converter Module
Design Note DN05108/D High Efficiency DC-DC Converter Module Device Application Input Voltage Output Power Topology I/O Isolation NCP12700 Module 9 to 36 Vdc Up to 15 W Output Specification Output Voltage
More informationFAN2013 2A Low-Voltage, Current-Mode Synchronous PWM Buck Regulator
FAN2013 2A Low-Voltage, Current-Mode Synchronous PWM Buck Regulator Features 95% Efficiency, Synchronous Operation Adjustable Output Voltage from 0.8V to V IN-1 4.5V to 5.5V Input Voltage Range Up to 2A
More informationNCP5360A. Integrated Driver and MOSFET
Integrated Driver and MOSFET The NCP5360A integrates a MOSFET driver, high-side MOSFET and low-side MOSFET into a 8mm x 8mm 56-pin QFN package. The driver and MOSFETs have been optimized for high-current
More informationReference Board User's Manual
Reference Board User's Manual THE CHIP PRODUCT SUMMARY SiC401A/B Input Voltage Range 3 V to 17 V Output Voltage Range 0.6 V to 5.5 V Operating Frequency 200 khz to 1 MHz Continuous Output Current 15 A
More informationNCP5339. Integrated Driver & MOSFETs
Integrated Driver & MOSFETs The NCP5339 integrates a MOSFET driver, high side MOSFET and low side MOSFET into a 6 mm x 6 mm 4 pin QFN package. The driver and MOSFETs have been optimized for high current
More informationIntermediate Bus Converter Demo Board Using SiP11205 or SiP11206
Intermediate Bus Converter Demo Board Using SiP05 or SiP06 SiP05/06DB INTRODUCTION Both SiP05 and SiP06 are controllers for half-bridge intermediate bus converters. The difference between SiP05 and SiP06
More informationEvaluates: MAX17536 in 5V Output-Voltage Application. MAX V Output Evaluation Kit. General Description. Quick Start.
MAX7536 5V Output Evaluation Kit Evaluates: MAX7536 in General Description The MAX7536 5V output evaluation kit (EV kit) provides a proven design to evaluate this high-voltage, highefficiency, synchronous
More informationQUICK START GUIDE FOR DEMONSTRATION CIRCUIT 968A-C ISOLATED DC/DC POWER CONVERTER LT1952 DESCRIPTION
LT9 DESCRIPTION Demonstration circuit 98A-C is isolated input to high current output /8th Brick footprint converter featuring the LT 9 switching controller. The DC98-C converts isolated V to 7V input to
More informationEvaluates: MAX17574 in 3.3V Output-Voltage Application. MAX V Output Evaluation Kit. General Description. Quick Start.
General Description The MAX17574 3.3V output evaluation kit (EV kit) provides a proven design to evaluate the MAX17574 high-voltage, high-efficiency, synchronous step-down DC-DC converter. The EV kit is
More informationSiP11206DB. 200 W 1/16 th Brick IBC Demo Board using SiP Vishay Siliconix
00 W / th Brick IBC Demo Board using SiP0 SiP0DB DESCRIPTION SiP0 is a half-bridge controller for intermediate bus converters. While SiP0 allows for overall better efficiency through out the input voltage
More informationPurpose. Table of Contents. Purpose...1. Introduction...2. General Product Information...2. Key Performance Summary Table...3
Purpose The RT8008 is a high-efficiency 1.5MHz current mode synchronous step-down regulator that can deliver up to 600mA output current from an input voltage range of 2.5V to 5.5V. This document explains
More informationIX Evaluation Board User s Guide INTEGRATED CIRCUITS DIVISION. 1. Introduction. 1.1 Features:
IX844 Evaluation Board User s Guide. Introduction IXYS Integrated Circuits Division's IX844 evaluation board contains all the necessary circuitry to demonstrate the features of a high voltage gate driver
More informationLM5022 Boost LED Driver Evaluation Board
LM5022 Boost LED Driver Evaluation Board Specifications Of The Board This evaluation board has been designed to demonstrate the LM5022 low-side controller as a step-up (boost) regulator for delivering
More informationEvaluates: MAXM V Output-Voltage Application. MAXM17552 Evaluation Kit. General Description. Quick Start. Features. Recommended Equipment
Click here for production status of specific part numbers. General Description The MAXM17552 evaluation kit (EV kit) is a demonstration circuit of the MAXM17552 ultra-small, high efficiency, current mode,
More informationEvaluates: MAX V Output-Voltage Application. MAX17546EVKITB# Evaluation Kit. Quick Start. General Description. Features. Recommended Equipment
Click here for production status of specific part numbers. MAX7546EVKITB# Evaluation Kit Evaluates: MAX7546 General Description The MAX7546 5V output evaluation kit (EV kit) provides a proven design to
More informationMAX V Output Evaluation Kit. Evaluates: MAX17543 in 3.3V Output-Voltage Application. Features. General Description.
General Description The MAX754.V output evaluation kit (EV kit) provides a proven design to evaluate the MAX754 high-voltage, high-efficiency, synchronous step-down DC-DC converter. The EV kit is preset
More informationDrGaN PLUS Development Board EPC9201/3 Quick Start Guide
DrGaN PLUS Development Board EPC9201/3 Quick Start Guide Optimized Half-Bridge Circuit for egan FETs EPC9203 Top side EPC9201 Top side 11 mm X 12 mm Mounting side DESCRIPTION This development board, measuring
More informationAOZ5237QI. High-Current, High-Performance DrMOS Power Module. General Description. Features. Applications. Typical Application Circuit
High-Current, High-Performance DrMOS Power Module General Description The is a high efficiency synchronous buck power stage module consisting of two asymmetrical MOSFETs and an integrated driver. The MOSFETs
More informationAOZ5048QI. High-Current, High-Performance DrMOS Power Module. Features. General Description. Applications. Typical Application Circuit
High-Current, High-Performance DrMOS Power Module General Description The AOZ5048QI is a high efficiency synchronous buck power stage module consisting of two asymmetrical MOSFETs and an integrated driver.
More informationN-Channel Synchronous MOSFETs With Break-Before-Make
New Product Si4738CY N-Channel Synchronous MOSFETs With Break-Before-Make FEATURES 0- to 20-V Operation Under-Voltage Lockout Shoot Through Resistant Fast Switching Times SO-16 Package Driver Impedance
More informationREFERENCE DESIGN 4669 INCLUDES:
Maxim > Design Support > Technical Documents > Reference Designs > Display Drivers > APP 4669 Maxim > Design Support > Technical Documents > Reference Designs > LED Lighting > APP 4669 Maxim > Design Support
More informationIS31LT3360 AIC DEMO BOARD GUIDE
DESCRIPTION The ISLT6 is a continuous mode inductive step-down converter, designed for driving a single LED or multiple series connected efficiently from a voltage source higher than the LED voltage. The
More informationAL9910AEV2 User Guide High Current and High Voltage LED Driver
High Current and High Voltage LED Driver General Description This demonstration board utilizes the AL9910A high voltage PWM LED Buck controller providing a cost effective solution for offline high brightness
More informationEvaluation Board Manual
SiP349, SiP349 Evaluation Board Manual DESCRIPTION SiP349 and SiP349 are a load switch that integrates multiple control features that simplify the design and increase the reliability of the circuitry connected
More informationHalf-Bridge N-Channel MOSFET Driver for Motor Control
Half-Bridge N-Channel MOSFET Driver for Motor Control FEATURES 5-V Gate Drive Undervoltage Lockout Pb-free Available Internal Bootstrap Diode Adaptive Shoot-Through Protection Motor Braking Shutdown Control
More informationHalf-Bridge N-Channel Programmable 1-A MOSFET Driver for DC/DC Conversion with Adjustable High Side Propagation Delay
New Product Half-Bridge N-Channel Programmable 1-A MOSFET Driver for DC/DC Conversion with Adjustable High Side Propagation Delay FEATURES 8-V or 12-V Low-Side Gate Drive Undervoltage Lockout Internal
More informationFDMF XS TM DrMOS
August 2009 FDMF6704 - XS TM DrMOS The Xtra Small, High Performance, High Frequency DrMOS Module Benefits Ultra compact size - 6 mm x 6 mm MLP, 44 % space saving compared to conventional MLP 8 mm x 8 mm
More informationRT9603. Synchronous-Rectified Buck MOSFET Drivers. General Description. Features. Applications. Ordering Information. Pin Configurations
Synchronous-Rectified Buck MOSFET Drivers General Description The RT9603 is a high frequency, dual MOSFET drivers specifically designed to drive two power N-MOSFETs in a synchronous-rectified buck converter
More informationLow-Noise 4.5A Step-Up Current Mode PWM Converter
Low-Noise 4.5A Step-Up Current Mode PWM Converter FP6298 General Description The FP6298 is a current mode boost DC-DC converter. It is PWM circuitry with built-in 0.08Ω power MOSFET make this regulator
More informationRT A, 2MHz, High Efficiency Synchronous Step-Down Converter. General Description. Features. Applications. Ordering Information
RT8073 6A, 2MHz, High Efficiency Synchronous Step-Down Converter General Description The RT8073 is a high efficiency PWM step-down converter and capable of delivering 6A output current over a wide input
More informationRT A, 2MHz, High Efficiency Synchronous Step-Down Converter. General Description. Features. Applications. Ordering Information
RT8072 5A, 2MHz, High Efficiency Synchronous Step-Down Converter General Description The RT8072 is a high efficiency PWM step-down converter and capable of delivering 5A output current over a wide input
More informationAVS / DVS and Margining Circuits for Vishay Power ICs SiC40X Series SMPS Regulators
VISHAY SILICONIX www.vishay.com ICs by Ronald Vinsant ABSTRACT There are many applications that require that a voltage rail within a system be capable of being adjusted by a digital or analog control signal.
More informationS 7V to 22V Input Range S Dynamically Selectable 1.5V/1.05V Output Voltage S Dynamically Adjustable Output Voltage Range (0 to 0.
9-539; Rev 0; 6/0 MAX5035 Evaluation Kit General Description The MAX5035 evaluation kit (EV kit) demonstrates the standard 5A application circuit of the MAX5035. This DC-DC converter steps down from the
More informationEvaluates: MAX17536 in 5V Output-Voltage Application. MAX V Output Evaluation Kit. General Description. Quick Start.
MAX7536 5V Output Evaluation Kit Evaluates: MAX7536 in 5V Output-Voltage Application General Description The MAX7536 5V output evaluation kit (EV kit) provides a proven design to evaluate this high-voltage,
More informationNovember 2013 Rev VIN FDMS7578. L1 IHLP-5050FD-01 41A, 1mOhm. Csnub 0 Ohm FDMS7650DC. 0 Ohm. 6.8nF. CFF 0.56nF
XRP64 November 0 Rev..0.0 GENERAL DESCRIPTION The XRP64 is a synchronous step-down controller for point-of load supplies up to 5A. A wide 4.5V to V input voltage range allows for single supply operation
More informationACT111A. 4.8V to 30V Input, 1.5A LED Driver with Dimming Control GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION CIRCUIT
4.8V to 30V Input, 1.5A LED Driver with Dimming Control FEATURES Up to 92% Efficiency Wide 4.8V to 30V Input Voltage Range 100mV Low Feedback Voltage 1.5A High Output Capacity PWM Dimming 10kHz Maximum
More informationUser s Manual ISL70040SEHEV2Z. User s Manual: Evaluation Board. High Reliability
User s Manual ISL70040SEHEV2Z User s Manual: Evaluation Board High Reliability Rev 0.00 Nov 2017 USER S MANUAL ISL70040SEHEV2Z Evaluation Board for the ISL70040SEH and ISL70023SEH UG147 Rev.0.00 1. Overview
More informationEvaluates: MAXM V Output-Voltage Application. MAXM17532 Evaluation Kit. General Description. Quick Start. Features. Recommended Equipment
General Description The MAXM17532 evaluation kit (EV kit) is a demonstration circuit of the MAXM17532 42V,0mA ultra-small, high efficiency, current mode, synchronous step-down DC-DC switching power module.
More informationEvaluates: MAX17546 in 5V Output-Voltage Application. MAX V Output Evaluation Kit. General Description. Quick Start.
MAX7546 5V Output Evaluation Kit Evaluates: MAX7546 in 5V Output-Voltage Application General Description The MAX7546 5V output evaluation kit (EV kit) provides a proven design to evaluate the MAX7546 high-voltage,
More informationIS32BL3556 WIDE INPUT VOLTAGE RANGE, HIGH EFFICIENCY FAULT TOLERANT LED DRIVER
ISBL6 WIDE INPUT VOLTAGE RANGE, HIGH EFFICIENCY DESCRIPTION RECOMMENDED EQUIPMENT The ISBL6 is a white LED driver for backlight applications based on a highly efficient boost controller operating over
More informationUser Guide. TDHBG2500P100: 2.5kW Half-bridge Evaluation Board. Introduction
User Guide TDHBG2500P100: 2.5kW Half-bridge Evaluation Board Introduction The TDHBG2500P100 half-bridge evaluation board provides the elements of a simple buck or boost converter for basic study of switching
More informationADT7350. General Description. Features. Applications. Typical Application Circuit. Sep / Rev. 0.
General Description The ADT7350 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5V to 24V with 1.2A peak output current. It includes current
More informationAN4781 Application note
Application note STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H Introduction The STEVAL-IFP028V1 is an evaluation board designed to analyze all IPS160H functionality. It is designed
More informationIS31LT3953_IS32LT3953 DEMO BOARD GUIDE
DESCRIPTION The IS31LT3953_IS32LT3953 is a DC-to-DC switching converter, which integrate an N-channel MOSFET to operate in a buck configuration. The device supply a wide input voltage between 4.5V and
More informationTFT-LCD DC/DC Converter with Integrated Backlight LED Driver
TFT-LCD DC/DC Converter with Integrated Backlight LED Driver Description The is a step-up current mode PWM DC/DC converter (Ch-1) built in an internal 1.6A, 0.25Ω power N-channel MOSFET and integrated
More informationFEBFL7701_L30U003A. 2.4 W LED Ballast Using FL7701. Featured Fairchild Product: FL7701
User Guide for FEBFL7701_L30U003A 2.4 W LED Ballast Using FL7701 Featured Fairchild Product: FL7701 Direct questions or comments about this evaluation board to: Worldwide Direct Support Fairchild Semiconductor.com
More informationWD3122EC. Descriptions. Features. Applications. Order information. High Efficiency, 28 LEDS White LED Driver. Product specification
High Efficiency, 28 LEDS White LED Driver Descriptions The is a constant current, high efficiency LED driver. Internal MOSFET can drive up to 10 white LEDs in series and 3S9P LEDs with minimum 1.1A current
More informationMAX V Output Evaluation Kit. Evaluates: MAX17572 in 5V Output-Voltage Application. General Description. Quick Start.
General Description The MAX17572 5V output evaluation kit (EV kit) provides a proven design to evaluate the MAX17572 high-voltage, high-efficiency, synchronous step-down DC-DC converter. The EV kit is
More informationSupertex inc. HV9971DB1. Isolated, Constant Current HV9971 LED Driver Demoboard. Board Layout and Connection Diagram.
Isolated, Constant Current HV9971 LED Driver Demoboard Board Layout and Connection Diagram Terminals for Monitoring Bus Voltage - + V AC = + 180-265VAC = 18-24V - I OUT = 330mA Connections 1. Input Voltage:
More informationDevelopment Board EPC9040 Quick Start Guide
Development Board EPC900 Quick Start Guide EPC0 Monolithic Half-Bridge with Gate Drive Revision.0 QUICK STRT GUIDE DESCRIPTION These development boards are in a monolithic half bridge topology with onboard
More informationefficient operation at 100kHz, although other inductors and other frequencies may be easily used. Figure 1. Half-bridge evaluation board
User Guide TDHBG500P00:.5kW Half-bridge Evaluation Board Introduction The TDHBG500P00 half-bridge evaluation board provides the elements of a simple buck or boost converter for basic study of switching
More informationHV739 ±100V 3.0A Ultrasound Pulser Demo Board
HV79 ±00V.0A Ultrasound Pulser Demo Board HV79DB Introduction The HV79 is a monolithic single channel, high-speed, high voltage, ultrasound transmitter pulser. This integrated, high performance circuit
More informationDIO6970 High-Efficiency 2A, 24V Input Synchronous Step Down Converter
DIO6970 High-Efficiency 2A, 24V Input Synchronous Step Down Converter Rev 0.2 Features Low R DS(ON) for internal switches (top/bottom) 130mΩ/80mΩ, 2.0A 4.5-24V input voltage range High-Efficiency Synchronous-Mode
More informationWD3119 WD3119. High Efficiency, 40V Step-Up White LED Driver. Descriptions. Features. Applications. Order information 3119 FCYW 3119 YYWW
High Efficiency, 40V Step-Up White LED Driver Http//:www.sh-willsemi.com Descriptions The is a constant current, high efficiency LED driver. Internal MOSFET can drive up to 10 white LEDs in series and
More informationYB1506 Step-up DC-DC Converter, White LED Driver
Description The YB1506 is a step-up(boost) DC-DC converter; operate as current source to drive up to 5 white LEDs in series. Series connecting of the LEDs provides identical LED currents resulting in uniform
More informationLD /01/2013. Boost Controller for LED Backlight. General Description. Features. Applications. Typical Application REV: 00
04/01/2013 Boost Controller for LED Backlight REV: 00 General Description The LD5861 is a wide-input asynchronous current mode boost controller, capable to operate in the range between 9V and 28V and to
More informationAOZ5038QI. 50A Continuous Current DrMOS Power Module. Features. General Description. Applications. Typical Application Circuit
50A Continuous Current DrMOS Power Module General Description The AOZ5038QI is a high efficiency synchronous buck power stage module consisting of two asymmetrical MOSFETs and an integrated driver. The
More informationADT7350. General Description. Applications. Features. Typical Application Circuit. Aug / Rev. 0.
General Description The ADT7350 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5V to 24V with 1.2A peak output current. It includes current
More informationQUICK START GUIDE FOR DEMONSTRATION CIRCUIT 968A-B ISOLATED DC/DC POWER CONVERTER LT1952 DESCRIPTION
LT95 DESCRIPTION Demonstration circuit 98A-B is isolated input to high current output /8th Brick footprint converter featuring the LT 95 switching controller. The DC98 converts isolated 8V to V input to
More information1 Applications. 2 Features TDA21240
1 Applications Desktop and Server VR buck-converter Single Phase and Multiphase POL CPU/GPU Regulation in Notebook, Desktop Graphics Cards, DDR Memory, Graphic Memory High Power Density Voltage Regulator
More informationSupertex inc. HV748DB1 HV748 ±75V 1.25A Ultrasound Pulser Demoboard
HV78DB HV78 ±75V.5A Ultrasound Pulser Demoboard Introduction The HV78 is a monolithic -channel, high speed, high voltage, ultrasound transmitter pulser. This integrated, high performance circuit is in
More informationTPS51124 User s Guide. SLUU252A APRIL 2006 Revised JULY High Performance Synchronous Buck EVM Using the TPS User s Guide
High Performance Synchronous Buck EVM Using the TPS51124 User s Guide 1 SLUU252A APRIL 2006 Revised JULY 2008 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right
More information