K6RIA, Extra Licensing Class. Circuits & Resonance for All!

Transcription

1 K6RIA, Extra Licensing Class Circuits & Resonance for All!

2 Amateur Radio Extra Class Element 4 Course Presentation ELEMENT 4 Groupings Rules & Regs Skywaves & Contesting Outer Space Comms Visuals & Video Modes Digital Excitement with Computers & Radios Modulate Your Transmitters Amps & Power Supplies Receivers with Great Filters

3 Amateur Radio Extra Class Element 4 Course Presentation ELEMENT 4 Groupings Oscillate & Synthesize This! Circuits & Resonance for All! Components in Your New Rig Logically Speaking of Counters Optos & OpAmps Plus Solar Test Gear, Testing, Testing 1,2,3 Antennas Feedlines & Safety

4 Amateur Radio Extra Class Circuits & Resonance for All! E5A01 Resonance can cause the voltage across reactances in series to be larger than the voltage applied to them. Let s go through the math step by step

5 Amateur Radio Extra Class Circuits & Resonance for All! x L = 2πFL ( 2πL)( 2πC ) 1 X C = 2πFC Resonance occurs in a circuit when X L is equal to X C. 2 πfl = 1 2πFC What we do to the left Therefore.. side of the equation, we must do to the right side, 1 f 2 and = what we do to the numerator we must do to the denominator, to maintain equality f 2 = 1 2 ( 2π ) LC

6 Amateur Radio Extra Class Circuits & Resonance for All! f 2 = 1 2 ( 2π ) LC f = o 2π 1 LC This is the resonant frequency formula.

7 Amateur Radio Extra Class Circuits & Resonance for All! E5A02 Resonance in an electrical circuit is the frequency at which the capacitive reactance equals the inductive reactance. E5A03 The magnitude of the impedance of a series R-L-C circuit at resonance is approximately equal to circuit resistance. At resonance, a series resonant circuit L and C present a low impedance so the circuit resistance is set by the resistor. E5A04 The magnitude of the impedance of a circuit with a resistor, an inductor and a capacitor all in parallel, at resonance is approximately equal to circuit resistance. At resonance, a parallel resonant circuit presents a very high impedance across the resistor.

8 Amateur Radio Extra Class Circuits & Resonance for All! E5A05 The magnitude of the current at the input of a series R-L-C circuit as the frequency goes through resonance is Maximum. At resonance a series circuit presents a low impedance and current would be limited by the resistor Tuning to either side of resonance would cause additional reactive resistance and therefore lower current flow in the circuit. Series and Parallel Resonant Circuits.

9 Amateur Radio Extra Class Circuits & Resonance for All! E5A06 The magnitude of the circulating current within the components of a parallel L-C circuit at resonance is at a maximum. Variation of Inductive and capacitive reactance with frequency (graph not to exact log-log scale)

10 Amateur Radio Extra Class Circuits & Resonance for All! E5A07 The magnitude of the current at the input of a parallel R-L-C circuit at resonance is at a Minimum. E5A08 The voltage and the current through and the voltage across a series resonant circuit are in phase. E5A09 The current through and the voltage across a parallel resonant circuit are in phase. (also true for a series circuit at resonance)

11 Amateur Radio Extra Class Circuits & Resonance for All! E5B07 The phase angle between the voltage across and the current through a series R-L-C circuit if X C is 500 ohms, R is 1 kilohm, and X L is 250 ohms is 14.0 degrees with the voltage lagging the current. Tangent of θ = Y / X Tangent of θ = 250/1000 Tangent of θ =.25 θ = Series RLC Circuits for Phase angle Calculations

12 Amateur Radio Extra Class Circuits & Resonance for All! E5B08 The phase angle between the voltage across and the current through a series R-L-C circuit if X C is 100 ohms, R is 100 ohms, and X L is 75 ohms is 14 degrees with the voltage lagging the current. Tangent of θ = Y / X Tangent of θ = (75-100)/100 Tangent of θ = -.25 θ = Rules for calculating impedances and phase angles 1) Impedances in series add together 2) Admittance is the reciprocal of impedance 3) Admittances in parallel add together 4) Inductive and capacitive reactance in series cancel 5) 1/j=-j Complex number axis diagram.

13 Amateur Radio Extra Class Circuits & Resonance for All! Here is more detail. In an ac circuit, when calculating the impedance of the circuit, the reactance and resistance must be added vectorially rather than algebraically. This vector addition can be understood best by looking at the following diagram: Vector Addition

14 Amateur Radio Extra Class Circuits & Resonance for All! E5B09 The relationship between the current through and the voltage across a capacitor is that the current leads the voltage by 90 degrees. E5B10 The relationship between the current through an inductor and the voltage across an inductor is that the voltage leads current by 90 degrees. Remember: ELI the ICE man. E5B11 The phase angle between the voltage across and the current through a series RLC circuit if X C is 25 ohms, R is 100 ohms, and X L is 50 ohms is 14 degrees with the voltage leading the current. Tangent of θ = Y / X Tangent of θ = (50-25)/100 Tangent of θ =.25 θ = j 50 -j Ω

15 Amateur Radio Extra Class Circuits & Resonance for All! E5B12 The phase angle between the voltage across and the current through a series RLC circuit if X C is 75 ohms, R is 100 ohms, and X L is 50 ohms is 14 degrees with the voltage lagging the current. Tangent of θ = Y / X Tangent of θ = (50-75)/100 Tangent of θ = -.25 θ = j Ω -j 75

16 Amateur Radio Extra Class Circuits & Resonance for All! E5B13 The phase angle between the voltage across and the current through a series RLC circuit if X C is 250 ohms, R is 1 kilohm, and X L is 500 ohms is degrees with the voltage leading the current. Tangent of θ = Y / X Tangent of θ = ( )/1000 Tangent of θ = 0.25 θ = j j Ω

17 Amateur Radio Extra Class Circuits & Resonance for All! E5C13 The Rectangular coordinate system is often used to display the resistive, inductive, and/or capacitive reactance components of impedance. E5C09 When using rectangular coordinates to graph the impedance of a circuit, the horizontal axis represents the voltage or current associated with the resistive component.

18 Amateur Radio Extra Class Circuits & Resonance for All! Rectangular Coordinates

19 Amateur Radio Extra Class Circuits & Resonance for All! Polar Coordinates

20 Amateur Radio Extra Class Circuits & Resonance for All! E5C22 In rectangular coordinates, what is the impedance of a network comprised of a 10-microhenry inductor in series with a 40-ohm resistor at 500 MHz? R = 40Ω X L = (2 π FL) X L = (6.28 x 500 x x 10 x 10-6 ) X L = 31,416 Ω Remember Inductive Reactance is positive so the answer is: 40 + j 31,400 E5C17 In rectangular coordinates, the impedance of a circuit that has an admittance of 5 millisiemens at -30 degrees is j100 ohms. Polar Impedance (Z) =1/admittance Z= 1/.005 Z= 200Ω Polar angle = 1/admittance angle = 1/- 30 = +30 Cos θ= resistance (R) / Impedance (Z) R = 200Ω x Cosine 30 R = 200Ω x Ω Sin θ= reactance (j) / Impedance (Z) j = 200 x Sine 30 j = 200Ω x.50 j100ω Don t be tempted to use a -j in front of the reactance with the admittance given initially with -30 o angle.

21 Amateur Radio Extra Class Circuits & Resonance for All! E5C10 When using rectangular coordinates to graph the impedance of a circuit, the vertical axis represents the voltage or current associated with the reactive component. E5C11 The two numbers used to define a point on a graph using rectangular coordinates represent the coordinate values along the horizontal and vertical axes. E5C12 If you plot the impedance of a circuit using the rectangular coordinate system and find the impedance point falls on the right side of the graph on the horizontal line, you know the circuit is equivalent to a pure resistance.

22 Amateur Radio Extra Class Circuits & Resonance for All! E5C19 In Figure E5-2, point 4 best represents that impedance of a series circuit consisting of a 400 ohm resistor and a 38 picofarad capacitor at 14 MHz. R = 400 Ω X C = 1/ (2 π FC) X C = 1/(6.28 x 14 x ) X C = -300 Ω Remember: Capacitive reactance is negative. Figure E5-2

23 Amateur Radio Extra Class Circuits & Resonance for All! E5C20 In Figure E5-2, Point 3 best represents the impedance of a series circuit consisting of a 300 ohm resistor and an 18 microhenry inductor at MHz. R =300 Ω X L = (2 π FL) X L = (6.28 x x 18) X L = Ω Remember: Inductive reactance is positive Answer is 300 Ω + j 395 Ω Figure E5-2

24 Amateur Radio Extra Class Circuits & Resonance for All! E5C21 In Figure E5-2, Point 1 best represents the impedance of a series circuit consisting of a 300 ohm resistor and a 19 picofarad capacitor at MHz. R = 300 Ω X C = 1/ (2 π FC) X C = 1/(6.28 x 21.2 x ) X C = Ω Remember: Capacitive reactance is negative Answer is 300 Ω j 395 Figure E5-2

25 Amateur Radio Extra Class Circuits & Resonance for All! E5C23 On Figure E5-2, Point 8 best represents the impedance of a series circuit consisting of a 300- ohm resistor, a 0.64-microhenry inductor and an 85-picofarad capacitor at MHz. R = 300 Ω X C = 1/ (2 π FC) X C = 1/(6.28 x 24.9 x ) X C = Ω (X C is negative) X L = (2 π FL) X L = (6.28 x 24.9 x.64) X L = Ω (X L is positive) Net reactance is the sum of X C and X L = Answer is 300 Ω + j 24.9 Figure E5-2

26 Amateur Radio Extra Class Circuits & Resonance for All! E5C14 The Polar coordinate system is often used to display the phase angle of a circuit containing resistance, inductive and/or capacitive reactance. E5C04 In polar coordinates, the impedance of a network consisting of a 400-ohm-reactance capacitor in series with a 300-ohm resistor is 500 ohms at an angle of degrees. Z= (X² + (X L X C )²) Z= ( 300² + (0-400)²) Z= (250,000) Z= 500 Ω θ = arc tan (reactance/resistance) arc tan (-400/300) arc tan (- 1.33) j Ω

27 Amateur Radio Extra Class Circuits & Resonance for All! Complex Numbers (Real and Imaginary and Operator j

28 Amateur Radio Extra Class Circuits & Resonance for All! j Operator as Vector Rotator

29 Amateur Radio Extra Class Circuits & Resonance for All! E5C01 In polar coordinates, the impedance of a network consisting of a 100-ohm-reactance inductor in series with a 100-ohm resistor is 141 ohms at an angle of 45. Z= (X² + Y²) Z= (100² + 100²) Z= ( 20,000) Z= Ω θ = arc tan (reactance/resistance) arc tan 100/100 arc tan 1 or 45 j Ω

30 Amateur Radio Extra Class Circuits & Resonance for All! E5C05 In polar coordinates, the impedance of a network consisting of a 400-ohm-reactance inductor in parallel with a 300-ohm resistor is 240 ohms at an angle of 36.9 degrees. Impedance = = = 120,000 / 500 = 240 Ω θ = arctan 1/ (Reactance/Resistance) θ= arctan 1/ (400 / 300) θ= arctan 1/ arctan =.750 θ =36.87

31 Amateur Radio Extra Class Circuits & Resonance for All! E5C02 In polar coordinates, the impedance of a network consisting of a 100-ohm-reactance inductor, a 100-ohm-reactance capacitor, and a 100- ohm resistor, all connected in series is 100 ohms at an angle of 0 degrees. Z= ( R² + (X L X C )²) Z= ( 100² + ( )²) Z= ( 10,000) Z= 100 Ω θ = arc tan (reactance/resistance) arc tan 0/100 arc tan 0 0 j j Ω Note- the Y side is the vector sum of the inductive reactance and capacitive reactance or (XL Xc) j 100-j Ω

32 Amateur Radio Extra Class Circuits & Resonance for All! E5C03 In polar coordinates, the impedance of a network consisting of a 300-ohm-reactance capacitor, a 600-ohm-reactance inductor, and a 400- ohm resistor, all connected in series is 500 ohms at an angle of 37 degrees. Z= (R² + (X L X c )²) Z= ( 400² + ( )²) Z= ( 250,000) Z= 500 Ω θ = arc tan (reactance/resistance) 300/400 arc tan j j Ω

33 Amateur Radio Extra Class Circuits & Resonance for All! E5C06 In polar coordinates, the impedance of a network consisting of a 100-ohm-reactance capacitor in series with a 100-ohm resistor is 141 ohms at an angle of -45 degrees. Z= (X² + (X L Xc)²) Z= ( 100² + (-100)²) Z= (20,000) Z= Ω Angle is arctan 1/ (reactance/resistance) arctan 1/ (100/100) arc tan (- 1) -45 E5C07 In polar coordinates, the impedance of a network comprised of a 100-ohm-reactance capacitor in parallel with a 100-ohm resistor is 71 ohms at an angle of -45 degrees. Admittance = 1/100 +( -j/100) j 0.01 Angle = arc tan.01/ (-45 in polar coordinates) Impedance = 1/ ( ( (.01)² x (.01)² )) 1/(.0141) Ώ

34 Amateur Radio Extra Class Circuits & Resonance for All! E5C07 In polar coordinates, the impedance of a network comprised of a 100-ohm-reactance capacitor in parallel with a 100-ohm resistor is 71 ohms at an angle of -45 degrees. Admittance = 1/100 +(-j/100) j 0.01 Angle =arc tan.01/ (-45 in polar coordinates) Impedance = 1/ ( ( (.01)² x (.01)² )) 1/(.0141) Ώ E5C08 In polar coordinates, the impedance of a network comprised of a 300-ohm-reactance inductor in series with a 400-ohm resistor is 500 ohms at an angle of 37 degrees. Z= (X² + (X L X C )²) Z= ( 400² + (0-300)²) Z= (250,000) Z= 500 Ω Angle is arc tan (X/R) arc tan (300/400) arc tan (.75) j Ω

35 Amateur Radio Extra Class Circuits & Resonance for All! E5C15 In polar coordinates, the impedance of a circuit of 100 -j100 ohms impedance is 141 ohms at an angle of -45 degrees. Z= (X² + (X L X C )²) Z= ( 100² + ( -100)²) Z= (20,000) Z= Ω Angle is arc tan (X/R) arc tan (-100/100) arc tan (-1) -45 E5C16 In polar coordinates, the impedance of a circuit that has an admittance of 7.09 milli-siemens at 45 degrees is 141 ohms at an angle of -45 degrees. Polar Impedance (Z) =1/admittance Z= 1/ Z= Ω Polar angle = 1 / j (admittance angle) 1/j(45 ) -j45

36 Amateur Radio Extra Class Circuits & Resonance for All! E5C18 In polar coordinates, the impedance of a series circuit consisting of a resistance of 4 ohms, an inductive reactance of 4 ohms, and a capacitive reactance of 1 ohm is 5 ohms at an angle of 37 degrees. Z= (X² + (XL Xc)²) Z= ( 4² + (4-1)²) Z= (25) or Z= 5 Ω Angle is arc tan (X/R) -j 1 + j 4 arc tan (3/4) arc tan (.75) 4Ω 36.86

37 Amateur Radio Extra Class Circuits & Resonance for All! E4B17 The bandwidth of the circuit's frequency response can be used as a relative measurement of the Q for a series-tuned circuit. The Narrower the bandwidth the higher the Q of the circuit. A large loading coil on a mobile whip helps antennas achieve high Q resonance.

38 Amateur Radio Extra Class Circuits & Resonance for All! E5A10 The half-power bandwidth of a parallel resonant circuit that has a resonant frequency of 1.8 MHz and a Q of 95 is 18.9 khz. B/W = Frequency/Q 1,800 KHz/ KHz For tuned circuits the quality factor, Q, is: For tuned circuits with Q greater than 10:

39 Amateur Radio Extra Class Circuits & Resonance for All! E5A11 The half-power bandwidth of a parallel resonant circuit that has a resonant frequency of 7.1 MHz and a Q of 150 is 47.3 khz. B/W = Frequency/Q 7,100 KHz/ KHz An amplifier s voltage gain will vary with frequency. At the cutoff frequencies, the voltage gain drops to of what is in the mid-band. These frequencies f 1 and f 2 are called the half-power frequencies. If the output voltage is 10 volts across a 100-ohm load when the gain is A at the mid-band, then the power output, PO at mid-band is:

40 Amateur Radio Extra Class Circuits & Resonance for All! At the cutoff frequency, the output voltage will be of what is at the mid-band; therefore, 7.07 volts. The power output is: Power Ratio in db The power output at the cutoff frequency points is one-half the mid-band power. The half-power bandwidth is between the frequencies f 1 and f 2. The power output at the frequencies is 3 db down from the mid-band power. E5A12 The half-power bandwidth of a parallel resonant circuit that has a resonant frequency of 3.7 MHz and a Q of 118 is 31.4 khz. B/W = Frequency/Q 3,700 KHz/ KHz

41 Amateur Radio Extra Class Circuits & Resonance for All! E5A13 The half-power bandwidth of a parallel resonant circuit that has a resonant frequency of MHz and a Q of 187 is 76.2 khz. B/W = Frequency/Q 14,250 KHz/ KHz E5A14 The resonant frequency of a series RLC circuit with R of 22 ohms, L of 50 microhenrys and C of 40 picofarads is 3.56 MHz. The equation can be solved with: L in Henries or Micro Henries and C in Farads or Micro Farads 50 mh 22 ohms 40 pf FR = 1 2 π L x C = x 50x10^-6 x 40 x10^-12 = 3.56 MHz

42 Amateur Radio Extra Class Circuits & Resonance for All! E5A15 The resonant frequency of a series RLC circuit with R of 56 ohms, L of 40 microhenrys and C of 200 picofarads is 1.78 MHz. FR = 1 2 π L x C = x 40x10^-6 x 200x10^-12 = 1.78 MHz E5A16 The resonant frequency of a parallel RLC circuit with R of 33 ohms, L of 50 microhenrys and C of 10 picofarads is 7.12 MHz. FR = 1 2 π L x C = x 50x10^-6 x 10x10^-12 = MHz E5A17 The resonant frequency of a parallel RLC circuit with R of 47 ohms, L of 25 microhenrys and C of 10 picofarads is 10.1 MHz. FR = 1 2 π L x C = x 25x10^-6 x 10x10^-12 = 10.1 MHz

43 Amateur Radio Extra Class Circuits & Resonance for All! E5B01 One time constant is the term for the time required for the capacitor in an RC circuit to be charged to 63.2% of the supply voltage. Schematics Curves

44 Amateur Radio Extra Class Circuits & Resonance for All! E5B02 One time constant is the time it takes for a charged capacitor in an RC circuit to discharge to 36.8% of its initial value of stored charge. Conversely a time constant is the time it takes a discharged capacitor to reach 63.2% of the applied voltage. Time Constants Charge % of applied voltage Discharge % of starting voltage % 36.80% % 13.50% % 5.00% % 1.80% % 0.70%

45 Amateur Radio Extra Class Circuits & Resonance for All! E5B03 The capacitor in an RC circuit is discharged to 13.5% percentage of the starting voltage after two time constants. %= (100-((100 x.632)) (100 (100 x.632) x.632)) 100+( ) 13.54% E5B04 The time constant of a circuit having two 220-microfarad capacitors and two 1-megohm resistors all in parallel is 220 seconds. TC (seconds) = R (megohms) x C (microfarads) TC =(1/2) x (220 x 2) 0.5 x seconds Remember that capacitors in parallel add and resistors of equal value in parallel are equal to one resistor divided by the number of resistors.

46 Amateur Radio Extra Class Circuits & Resonance for All! E5B05 It will take.020 seconds (or 20 milliseconds) for an initial charge of 20 V DC to decrease to 7.36 V DC in a 0.01-microfarad capacitor when a 2-megohm resistor is connected across it. To discharge to 7.36 VDC would take one time constant 20V (.632 x 20V) 7.36 Volts TC = 2 x seconds 20 milliseconds E5B06 It takes 450 seconds for an initial charge of 800 V DC to decrease to 294 V DC in a 450-microfarad capacitor when a 1- megohm resistor is connected across it. To discharge to 294 VDC would take one time constant 800V (.632 x 800V) = 294.4V TC = 1 x seconds

47 Amateur Radio Extra Class Circuits & Resonance for All! E5D01 As frequency increases, RF current flows in a thinner layer of the conductor, closer to the surface this is called skin effect. RF UHF Current flow in cross section of a conductor E5D02 The resistance of a conductor is different for RF currents than for direct currents because of skin effect. E5D03 A capacitor is a device that is used to store electrical energy in an electrostatic field. E5D04 The Joule is the unit of electrical energy stored in an electrostatic field. A Joule is defined as a quantity of energy equal to one Newton of force acting over 1 meter

48 Amateur Radio Extra Class Circuits & Resonance for All! E5D05 The region surrounding a magnet through which a magnetic force acts is a magnetic field. E5D06 The direction of the magnetic field oriented about a conductor in relation to the direction of electron flow is in a direction determined by the left-hand rule. Direction of Magnetic Field Magnetic Field surrounding wire Wire or Conductor with current through it Left-Hand Rule

49 Amateur Radio Extra Class Circuits & Resonance for All! E5D07 The amount of current determines the strength of a magnetic field around a conductor. E5D08 Potential energy is the term for energy that is stored in an electromagnetic or electrostatic field. E5D09 Reactive power is the term for an out-of-phase, nonproductive power associated with inductors and capacitors. E5D10 In a circuit that has both inductors and capacitors the reactive power is repeatedly exchanged between the associated magnetic and electric fields, but is not dissipated. (assuming perfect lossless components) E5D11 The true power can be determined in an AC circuit where the voltage and current are out of phase by multiplying the apparent power times the power factor. Apparent power is the voltage times the current into the circuit True Power is the apparent power times the power factor The only time true power and apparent power are the same is if the power factor is 1.00 (the phase angle is zero)

50 Amateur Radio Extra Class Circuits & Resonance for All! Apparent and True Power

51 Amateur Radio Extra Class Circuits & Resonance for All! E5D12 The power factor (PF) of an R-L circuit having a 60 degree phase angle between the voltage and the current is 0.5. PF is the cosine function of the voltage to current angle PF =cosine of 60 PF= 0.5 E5D13 80 watts are consumed in a circuit having a power factor of 0.2 if the input is 100-V AC at 4 amperes. Power Consumed = V x I x PF 100 x 4 x.2 80 watts

52 Amateur Radio Extra Class Circuits & Resonance for All! E5D14 The power is consumed in a circuit consisting of a 100 ohm resistor in series with a 100 ohm inductive reactance drawing 1 ampere is 100 Watts. Power (real) = I² x R Power (real) = (1)² x watts. (Only the circuit resistance consumes power) E5D15 Wattless, nonproductive power is reactive power. E5D16 The power factor of an RL circuit having a 45 degree phase angle between the voltage and the current is PF = Cosine of 45 PF = 0.707

53 Amateur Radio Extra Class Circuits & Resonance for All! E5D17 The power factor of an RL circuit having a 30 degree phase angle between the voltage and the current is PF Cosine of 30 PF = E5D watts are consumed in a circuit having a power factor of 0.6 if the input is 200V AC at 5 amperes. Power Consumed = V x I x PF 200 x 5 x watts E5D19 The power consumed in a circuit having a power factor of 0.71 if the apparent power is 500 watts is 355 W. Power Consumed = Apparent power x PF 500 x watts

54 Amateur Radio Extra Class Circuits & Resonance for All! E4E04 Conducted and radiated noise caused by an automobile alternator can be suppressed by connecting the radio's power leads directly to the battery and by installing Feed Through capacitors in line with the alternator leads. E4E05 Noise from an electric motor can be suppressed by installing a brute-force AC-line filter in series with the motor leads. E6D08 Core permeability (for a given size core) is the property that determines the inductance of a toroidal inductor with a 10-turn winding.

55 Amateur Radio Extra Class Circuits & Resonance for All! E6D09 The usable frequency range of inductors that use toroidal cores, assuming a correct selection of core material for the frequency being used is from less than 20 Hz to approximately 300 MHz. E6D10 One important reason for using powdered-iron toroids rather than ferrite toroids in an inductor is that powdered-iron toroids generally have better temperature stability. Applications for powdered Iron toroids would be oscillator and filter circuits where inductance stability with temperature is important. E6D12 A primary advantage of using a toroidal core instead of a solenoidal core in an inductor is that toroidal cores contain most of the magnetic field within the core material.

56 Amateur Radio Extra Class Circuits & Resonance for All! E6D13 Forty three turns of wire will be required to produce a 1-mH inductor using a ferrite toroidal core that has an inductance index (AL) value of 523 millihenrys/1000 turns. N turns = 1000 x ( (L / AL)) N turns = 1000 x ( (1 / 523)) 43.7 turns E6D14 Thirty five turns of wire will be required to produce a 5- microhenry inductor using a powdered-iron toroidal core that has an inductance index (A L) value of 40 microhenrys/100 turns. N turns = 100 x ( (L / AL)) N turns = 100 x ( (5 / 40)) turns E6D18 One reason for using ferrite toroids rather than powdered-iron toroids in an inductor is that Ferrite toroids generally require fewer turns to produce a given inductance value.

57 Element 4 Extra Class Question Pool Circuits & Resonance for All! Valid July 1, 2008 Through June 30, 2012

58 E5A01 What can cause the voltage across reactances in series to be larger than the voltage applied to them? A. Resonance B. Capacitance C. Conductance D. Resistance

59 E5A02 What is resonance in an electrical circuit? A. The highest frequency that will pass current B. The lowest frequency that will pass current C. The frequency at which the capacitive reactance equals the inductive reactance D. The frequency at which the reactive impedance equals the resistive impedance

60 What is the magnitude of the impedance of a series R-L-C circuit at resonance? E5A03 A. High, as compared to the circuit resistance B. Approximately equal to capacitive reactance C. Approximately equal to inductive reactance D. Approximately equal to circuit resistance

61 E5A04 What is the magnitude of the impedance of a circuit with a resistor, an inductor and a capacitor all in parallel, at resonance? A. Approximately equal to circuit resistance B. Approximately equal to inductive reactance C. Low, as compared to the circuit resistance D. Approximately equal to capacitive reactance

62 E5A05 What is the magnitude of the current at the input of a series R-L-C circuit as the frequency goes through resonance? A. Minimum B. Maximum C. R/L D. L/R

63 E5A06 What is the magnitude of the circulating current within the components of a parallel L-C circuit at resonance? A. It is at a minimum B. It is at a maximum C. It equals 1 divided by the quantity [ 2 multiplied by Pi, multiplied by the square root of ( inductance "L" multiplied by capacitance "C" ) ] D. It equals 2 multiplied by Pi, multiplied by frequency "F", multiplied by inductance "L"

64 What is the magnitude of the current at the input of a parallel R-L-C circuit at resonance? E5A07 A.Minimum B. Maximum C.R/L D.L/R

65 E5A08 What is the phase relationship between the current through and the voltage across a series resonant circuit? A. The voltage leads the current by 90 degrees B. The current leads the voltage by 90 degrees C. The voltage and current are in phase D. The voltage and current are 180 degrees out of phase

66 E5A09 What is the phase relationship between the current through and the voltage across a parallel resonant circuit? A. The voltage leads the current by 90 degrees B. The current leads the voltage by 90 degrees C. The voltage and current are in phase D. The voltage and current are 180 degrees out of phase

67 E5B07 What is the phase angle between the voltage across and the current through a series R-L-C circuit if XC is 500 ohms, R is 1 kilohm, and XL is 250 ohms? A degrees with the voltage leading the current B degrees with the voltage leading the current C degrees with the voltage lagging the current D degrees with the voltage lagging the current

68 E5B08 What is the phase angle between the voltage across and the current through a series R-L-C circuit if XC is 100 ohms, R is 100 ohms, and XL is 75 ohms? A. 14 degrees with the voltage lagging the current B. 14 degrees with the voltage leading the current C. 76 degrees with the voltage leading the current D. 76 degrees with the voltage lagging the current

69 What is the relationship between the current through and the voltage across a capacitor? E5B09 A. Voltage and current are in phase B. Voltage and current are 180 degrees out of phase C.Voltage leads current by 90 degrees D.Current leads voltage by 90 degrees

70 E5B10 What is the relationship between the current through an inductor and the voltage across an inductor? A. Voltage leads current by 90 degrees B. Current leads voltage by 90 degrees C. Voltage and current are 180 degrees out of phase D. Voltage and current are in phase

71 E5B11 What is the phase angle between the voltage across and the current through a series RLC circuit if XC is 25 ohms, R is 100 ohms, and XL is 50 ohms? A. 14 degrees with the voltage lagging the current B. 14 degrees with the voltage leading the current C. 76 degrees with the voltage lagging the current D. 76 degrees with the voltage leading the current

72 E5B12 What is the phase angle between the voltage across and the current through a series RLC circuit if XC is 75 ohms, R is 100 ohms, and XL is 50 ohms? A. 76 degrees with the voltage lagging the current B. 14 degrees with the voltage leading the current C.14 degrees with the voltage lagging the current D.76 degrees with the voltage leading the current

73 E5B13 What is the phase angle between the voltage across and the current through a series RLC circuit if XC is 250 ohms, R is 1 kilohm, and XL is 500 ohms? A degrees with the voltage lagging the current B degrees with the voltage leading the current C degrees with the voltage lagging the current D degrees with the voltage leading the current

74 E5C13 What coordinate system is often used to display the resistive, inductive, and/or capacitive reactance components of an impedance? A. Maidenhead grid B. Faraday grid C. Elliptical coordinates D. Rectangular coordinates

75 E5C09 When using rectangular coordinates to graph the impedance of a circuit, what does the horizontal axis represent? A. The voltage or current associated with the resistive component B. The voltage or current associated with the reactive component C. The sum of the reactive and resistive components D. The difference between the resistive and reactive components

76 E5C22 In rectangular coordinates, what is the impedance of a network comprised of a 10-microhenry inductor in series with a 40-ohm resistor at 500 MHz? A j31,400 B j31,400 C. 31,400 + j40 D. 31,400 - j40

77 E5C17 In rectangular coordinates, what is the impedance of a circuit that has an admittance of 5 millisiemens at -30 degrees? A j100 ohms B j100 ohms C j100 ohms D j100 ohms

78 E5C10 When using rectangular coordinates to graph the impedance of a circuit, what does the vertical axis represent? A. The voltage or current associated with the resistive component B. The voltage or current associated with the reactive component C. The sum of the reactive and resistive components D. The difference between the resistive and reactive components

79 E5C11 What do the two numbers represent that are used to define a point on a graph using rectangular coordinates? A. The magnitude and phase of the point B. The sine and cosine values C. The coordinate values along the horizontal and vertical axes D. The tangent and cotangent values

80 E5C12 If you plot the impedance of a circuit using the rectangular coordinate system and find the impedance point falls on the right side of the graph on the horizontal line, what do you know about the circuit? A. It has to be a direct current circuit B. It contains resistance and capacitive reactance C. It contains resistance and inductive reactance D. It is equivalent to a pure resistance

81 E5C19 Which point on Figure E5-2 best represents that impedance of a series circuit consisting of a 400 ohm resistor and a 38 picofarad capacitor at 14 MHz? A. Point 2 B. Point 4 C. Point 5 D. Point 6

82 E5C20 Which point in Figure E5-2 best represents the impedance of a series circuit consisting of a 300 ohm resistor and an 18 microhenry inductor at MHz? A. Point 1 B. Point 3 C. Point 7 D. Point 8

83 E5C21 Which point on Figure E5-2 best represents the impedance of a series circuit consisting of a 300 ohm resistor and a 19 picofarad capacitor at MHz? A. Point 1 B. Point 3 C. Point 7 D. Point 8

84 E5C23 Which point on Figure E5-2 best represents the impedance of a series circuit consisting of a 300-ohm resistor, a 0.64-microhenry inductor and an 85-picofarad capacitor at MHz? A. Point 1 B. Point 3 C. Point 5 D. Point 8

85 E5C14 What coordinate system is often used to display the phase angle of a circuit containing resistance, inductive and/or capacitive reactance? A. Maidenhead grid B. Faraday grid C. Elliptical coordinates D. Polar coordinates

86 E5C04 In polar coordinates, what is the impedance of a network consisting of a 400-ohm-reactance capacitor in series with a 300-ohm resistor? A. 240 ohms at an angle of 36.9 degrees B. 240 ohms at an angle of degrees C. 500 ohms at an angle of 53.1 degrees D. 500 ohms at an angle of degrees

87 E5C01 In polar coordinates, what is the impedance of a network consisting of a 100-ohm-reactance inductor in series with a 100-ohm resistor? A. 121 ohms at an angle of 35 degrees B. 141 ohms at an angle of 45 degrees C. 161 ohms at an angle of 55 degrees D. 181 ohms at an angle of 65 degrees

88 E5C05 In polar coordinates, what is the impedance of a network consisting of a 400-ohm-reactance inductor in parallel with a 300-ohm resistor? A. 240 ohms at an angle of 36.9 degrees B. 240 ohms at an angle of degrees C. 500 ohms at an angle of 53.1 degrees D. 500 ohms at an angle of degrees

89 E5C02 In polar coordinates, what is the impedance of a net-work consisting of a 100-ohm-reactance inductor, a 100-ohm-reactance capacitor, and a 100-ohm resistor, all connected in series? A. 100 ohms at an angle of 90 degrees B. 10 ohms at an angle of 0 degrees C.10 ohms at an angle of 90 degrees D.100 ohms at an angle of 0 degrees

90 E5C03 In polar coordinates, what is the impedance of a net-work consisting of a 300-ohm-reactance capacitor, a 600-ohm-reactance inductor, and a 400-ohm resistor, all connected in series? A. 500 ohms at an angle of 37 degrees B. 900 ohms at an angle of 53 degrees C. 400 ohms at an angle of 0 degrees D ohms at an angle of 180 degrees

91 E5C06 In polar coordinates, what is the impedance of a network consisting of a 100-ohm-reactance capacitor in series with a 100-ohm resistor? A. 121 ohms at an angle of -25 degrees B. 191 ohms at an angle of -85 degrees C.161 ohms at an angle of -65 degrees D.141 ohms at an angle of -45 degrees

92 E5C07 In polar coordinates, what is the impedance of a network comprised of a 100-ohm-reactance capacitor in parallel with a 100-ohm resistor? A. 31 ohms at an angle of -15 degrees B. 51 ohms at an angle of -25 degrees C. 71 ohms at an angle of -45 degrees D. 91 ohms at an angle of -65 degrees

93 E5C08 In polar coordinates, what is the impedance of a network comprised of a 300-ohm-reactance inductor in series with a 400-ohm resistor? A. 400 ohms at an angle of 27 degrees B. 500 ohms at an angle of 37 degrees C. 500 ohms at an angle of 47 degrees D. 700 ohms at an angle of 57 degrees

94 E5C15 In polar coordinates, what is the impedance of a circuit of 100 -j100 ohms impedance? A. 141 ohms at an angle of -45 degrees B. 100 ohms at an angle of 45 degrees C. 100 ohms at an angle of -45 degrees D. 141 ohms at an angle of 45 degrees

95 E5C16 In polar coordinates, what is the impedance of a circuit that has an admittance of 7.09 millisiemens at 45 degrees? A x 10 E05 ohms at an angle of 45 degrees B. 141 ohms at an angle of -45 degrees C. 19,900 ohms at an angle of -45 degrees D. 141 ohms at an angle of 45 degrees

96 E5C18 In polar coordinates, what is the impedance of a series circuit consisting of a resistance of 4 ohms, an inductive reactance of 4 ohms, and a capacitive reactance of 1 ohm? A. 6.4 ohms at an angle of 53 degrees B. 5 ohms at an angle of 37 degrees C. 5 ohms at an angle of 45 degrees D. 10 ohms at an angle of -51 degrees

97 E4B17 Which of the following can be used as a relative measurement of the Q for a seriestuned circuit? A. The inductance to capacitance ratio B. The frequency shift C. The bandwidth of the circuit's frequency response D. The resonant frequency of the circuit

98 E5A10 What is the half-power bandwidth of a parallel resonant circuit that has a resonant frequency of 1.8 MHz and a Q of 95? A khz B khz C khz D khz

99 E5A11 What is the half-power bandwidth of a parallel resonant circuit that has a resonant frequency of 7.1 MHz and a Q of 150? A Hz B Hz C.47.3 khz D khz

100 E5A12 What is the half-power bandwidth of a parallel resonant circuit that has a resonant frequency of 3.7 MHz and a Q of 118? A khz B khz C khz D khz

101 E5A13 What is the half-power bandwidth of a parallel resonant circuit that has a resonant frequency of MHz and a Q of 187? A khz B khz C khz D khz

102 E5A14 What is the resonant frequency of a series RLC circuit if R is 22 ohms, L is 50 microhenrys and C is 40 picofarads? A MHz B MHz C MHz D MHz

103 E5A15 What is the resonant frequency of a series RLC circuit if R is 56 ohms, L is 40 microhenrys and C is 200 picofarads? A MHz B MHz C MHz D MHz

104 E5A16 What is the resonant frequency of a parallel RLC circuit if R is 33 ohms, L is 50 microhenrys and C is 10 picofarads? A MHz B khz C khz D MHz

105 E5A17 What is the resonant frequency of a parallel RLC circuit if R is 47 ohms, L is 25 microhenrys and C is 10 picofarads? A MHz B MHz C khz D khz

106 E5B01 What is the term for the time required for the capacitor in an RC circuit to be charged to 63.2% of the supply voltage? A. An exponential rate of one B. One time constant C. One exponential period D. A time factor of one

107 E5B02 What is the term for the time it takes for a charged capacitor in an RC circuit to discharge to 36.8% of its initial value of stored charge? A. One discharge period B. An exponential discharge rate of one C. A discharge factor of one D. One time constant

108 E5B03 The capacitor in an RC circuit is discharged to what percentage of the starting voltage after two time constants? A. 86.5% B. 63.2% C. 36.8% D. 13.5%

109 E5B04 What is the time constant of a circuit having two 220-microfarad capacitors and two 1-megohm resistors all in parallel? A. 55 seconds B. 110 seconds C. 440 seconds D. 220 seconds

110 E5B05 How long does it take for an initial charge of 20 V DC to decrease to 7.36 V DC in a 0.01-microfarad capacitor when a 2-megohm resistor is connected across it? A.0.02 seconds B seconds C.20 seconds D.40 seconds

111 E5B06 How long does it take for an initial charge of 800 V DC to decrease to 294 V DC in a 450-microfarad capacitor when a 1-megohm resistor is connected across it? A seconds B. 9 seconds C. 450 seconds D. 900 seconds

112 E5D01 What is the result of skin effect? A. As frequency increases, RF current flows in a thinner layer of the conductor, closer to the surface B. As frequency decreases, RF current flows in a thinner layer of the conductor, closer to the surface C. Thermal effects on the surface of the conductor increase the impedance D. Thermal effects on the surface of the conductor decrease the impedance

113 E5D02 Why is the resistance of a conductor different for RF currents than for direct currents? A. Because the insulation conducts current at high frequencies B. Because of the Heisenburg Effect C. Because of skin effect D. Because conductors are nonlinear devices

114 What device is used to store electrical E5D03 energy in an electrostatic field? A. A battery B. A transformer C. A capacitor D. An inductor

115 What unit measures electrical energy E5D04 stored in an electrostatic field? A. Coulomb B. Joule C. Watt D. Volt

116 E5D05 What is a magnetic field? A. Electric current through the space around a permanent magnet B. The region surrounding a magnet through which a magnetic force acts C. The space between the plates of a charged capacitor, through which a magnetic force acts D. The force that drives current through a resistor

117 E5D06 In what direction is the magnetic field oriented about a conductor in relation to the direction of electron flow? A. In the same direction as the current B. In a direction opposite to the current C. In all directions; omnidirectional D. In a direction determined by the lefthand rule

118 What determines the strength of a E5D07 magnetic field around a conductor? A. The resistance divided by the current B. The ratio of the current to the resistance C. The diameter of the conductor D. The amount of current

119 E5D08 What is the term for energy that is stored in an electromagnetic or electrostatic field? A.Amperes-joules B. Potential energy C.Joules-coulombs D.Kinetic energy

120 E5D09 What is the term for an out-of-phase, nonproductive power associated with inductors and capacitors? A. Effective power B. True power C. Peak envelope power D. Reactive power

121 E5D10 In a circuit that has both inductors and capacitors, what happens to reactive power? A. It is dissipated as heat in the circuit B. It is repeatedly exchanged between the associated magnetic and electric fields, but is not dissipated C. It is dissipated as kinetic energy in the circuit D. It is dissipated in the formation of inductive and capacitive fields

122 E5D11 How can the true power be determined in an AC circuit where the voltage and current are out of phase? A. By multiplying the apparent power times the power factor B. By dividing the reactive power by the power factor C. By dividing the apparent power by the power factor D. By multiplying the reactive power times the power factor

123 E5D12 What is the power factor of an R-L circuit having a 60 degree phase angle between the voltage and the current? A B C. 0.5 D. 1.73

124 E5D13 How many watts are consumed in a circuit having a power factor of 0.2 if the input is 100-V AC at 4 amperes? A. 400 watts B. 80 watts C watts D. 50 watts

125 E5D14 How much power is consumed in a circuit consisting of a 100 ohm resistor in series with a 100 ohm inductive reactance drawing 1 ampere? A Watts B. 100 Watts C Watts D. 200 Watts

126 E5D15 What is reactive power? A. Wattless, nonproductive power B. Power consumed in wire resistance in an inductor C. Power lost because of capacitor leakage D. Power consumed in circuit Q

127 E5D16 What is the power factor of an RL circuit having a 45 degree phase angle between the voltage and the current? A B. 1.0 C. 0.5 D

128 E5D17 What is the power factor of an RL circuit having a 30 degree phase angle between the voltage and the current? A B. 0.5 C D

129 E5D18 How many watts are consumed in a circuit having a power factor of 0.6 if the input is 200V AC at 5 amperes? A. 200 watts B watts C watts D. 600 watts

130 E5D19 How many watts are consumed in a circuit having a power factor of 0.71 if the apparent power is 500 watts? A. 704 W B. 355 W C. 252 W D mw

131 E4E04 How can conducted and radiated noise caused by an automobile alternator be suppressed? A. By installing filter capacitors in series with the DC power lead and by installing a blocking capacitor in the field lead B. By connecting the radio to the battery by the longest possible path and installing a blocking capacitor in both leads C. By installing a high-pass filter in series with the radio's power lead and a low-pass filter in parallel with the field lead D. By connecting the radio's power leads directly to the battery and by installing coaxial capacitors in line with the alternator leads

132 How can noise from an electric motor be suppressed? E4E05 A. By installing a ferrite bead on the AC line used to power the motor B. By installing a brute-force AC-line filter in series with the motor leads C. By installing a bypass capacitor in series with the motor leads D. By using a ground-fault current interrupter in the circuit used to power the motor

133 E6D08 What material property determines the inductance of a toroidal inductor with a 10- turn winding? A. Core load current B. Core resistance C. Core reactivity D. Core permeability

134 E6D09 What is the usable frequency range of inductors that use toroidal cores, assuming a correct selection of core material for the frequency being used? A. From a few khz to no more than 30 MHz B. From less than 20 Hz to approximately 300 MHz C. From approximately 1000 Hz to no more than 3000 khz D. From about 100 khz to at least 1000 GHz

135 E6D10 What is one important reason for using powdered-iron toroids rather than ferrite toroids in an inductor? A. Powdered-iron toroids generally have greater initial permeabilities B. Powdered-iron toroids generally have better temperature stability C. Powdered-iron toroids generally require fewer turns to produce a given inductance value D. Powdered-iron toroids have the highest power handling capacity

136 E6D12 What is a primary advantage of using a toroidal core instead of a solenoidal core in an inductor? A. Toroidal cores contain most of the magnetic field within the core material B. Toroidal cores make it easier to couple the magnetic energy into other components C. Toroidal cores exhibit greater hysteresis D. Toroidal cores have lower Q characteristics

137 E6D13 How many turns will be required to produce a 1-mH inductor using a ferrite toroidal core that has an inductance index (A L) value of 523 millihenrys/1000 turns? A. 2 turns B. 4 turns C. 43 turns D. 229 turns

138 E6D14 How many turns will be required to produce a 5- microhenry inductor using a powdered-iron toroidal core that has an inductance index (A L) value of 40 microhenrys/100 turns? A. 35 turns B. 13 turns C. 79 turns D. 141 turns

139 E6D18 What is one reason for using ferrite toroids rather than powdered-iron toroids in an inductor? A. Ferrite toroids generally have lower initial permeabilities B. Ferrite toroids generally have better temperature stability C. Ferrite toroids generally require fewer turns to produce a given inductance value D. Ferrite toroids are easier to use with surface mount technology