Liquid level monitors and controls

Size: px
Start display at page:

Download "Liquid level monitors and controls"

Transcription

1 Liquid level monitors and controls ontent M-ENE, M-ENE MAX... / 8 M-ENS... / 83 M-ENS UP/DOWN... / 84 M-ENN... / 85 M-ENN UP/DOWN... / 86 Accessories for liquid level relays... / 87 Technical data M-ENE, M-ENE MAX... / 88 M-ENS, M-ENS UP/DOWN... / 89 M-ENN, M-ENN UP/DOWN... / 90 Approvals and marks... / 6 Technical diagrams... /0 Dimensional drawings... /03 Accessories... /04 /8 D

2 M-ENE, M-ENE MAX M-ENE SV F 05 SV F 053 SV F 05 SV F 054 M-ENE MAX SV F 0494 SV F 0495 SV F 0496 SVR F9500 The liquid level relays M-ENE and M-ENE MAX are used to monitor levels of conductive liquids, for example in pump control systems for dry-running or overflow monitoring. The measuring principle is based on the occurring resistance change when moisting single-pole electrodes. The single-pole electrodes (see also section Accessories) are connected to the terminals and or MAX. If the is applied to A-A and the electrodes are wet, the output relay of the M-ENE is energized and the output relay of the M-ENE MAX is de-energized. The output relay of the M-ENE de-energizes if the electrodes are no longer wet. The output relay of the M-ENE MAX energizes if the electrodes are no longer wet. Function diagram M-ENE onnection diagram M-ENE A-A A-A Ground reference electrode Minimum level 3-4 Output contact - open-circuit principle 3-4 SVR F9400 Function diagram M-ENE MAX A-A onnection diagram M-ENE MAX A-A Ground reference electrode MAX Max. level 3-4 Output contact - closed-circuit principle 3-4 R: yellow LED - relay status If a metal tank is used, the ground reference electrode is not required. In this case the cable can be connected directly to the metal surface of the tank. Application examples M-ENE M-ENE MAX M-ENE und M-ENE MAX Monitoring of pump systems for dry running (ENE ) and overflow (ENE MAX) onnection of electrodes possible at and /MAX 3 versions Optimal price/performance ratio n/o contact: Open-circuit principle for M-ENE losed-circuit principle for M-ENE MAX LED for status indication Suitable for Not suitable for spring water acids, bases chemically pure water ethylene glycol drinking water liquid fertilizers fuel concentrated alcohol sea water milk, beer, coffee oils paraffin sewage non-concentrated alcohol explosive areas (liquid gas) lacquers Type M-ENE M-ENE MAX 4 V A 0-30 V A 0-40 V A 4 V A 0-30 V A 0-40 V A Order code SVR R9500 SVR R9500 SVR R9500 SVR R9400 SVR R9400 SVR R9400 Pack. pieces piece piece Accessories... /87 and /04 Technical data.../88 Dimensional drawings... / / / / / / / 0.33 /8 D

3 M-ENS The M-ENS monitors levels of conductive liquids and is used for example for liquid level control in pump systems. It can be used for filling or draining tanks for example. SVR F00 It is also suitable for monitoring the conductivity of liquids. The measuring principle is based on the resistance change sensed by single-pole electrodes. After the is applied to the terminals A and A, the output relay is de-energized. The probes must be connected to, MAX,. The output relay energizes if the liquid exceeds the maximum level ( and MAX wet) and de-energizes if the liquid level is below the minimum level (MAX and dry). Based on the measuring circuit there will be a response delay of approx. 50 ms at maximum sensitivity. Different levels in one tank can be controlled by up to 5 M-ENS without interfering with each other. Function diagram M-ENS M-ENS "Sens." - sensitivity potentiometer for adjusting the response sensitivity R: yellow LED - relay status U: green LED - control Marker label Max. Min. A-A -4 - Application examples SV F 055 When using a metal tank the electrode is not required. In this case the cable can be connected directly to the metal surface of the tank. onnection diagram M-ENS fill SV F 056 drain SV F 057 SV F 058 A-A Ground reference electrode MAX Maximum level Minimum level (5)-(6)/4(8) Output contacts - open-circuit principle ascading The electrode inputs can be interconnected as required, which ensures simple monitoring of different liquid levels. SV F 059 Redundancy Redundant liquid level monitoring or control can be implemented by connecting the electrodes to two s. This makes the application much safer. SV F 060 Monitoring and control of liquid levels (when draining or filling liquids in tanks) Monitoring and control of mixture ratios (conductivity of liquids) Adjustable response sensitivity 5-00 k 4 versions 4-45 V A Version with protective separation acc. to VDE 060 J ascadable c/o contact or n/o and n/c contact LEDs for status indication Suitable for Not suitable for spring water acids, bases chemically pure water ethylene glycol drinking water liquid fertilizers fuel concentrated alcohol sea water milk, beer, coffee oils paraffin sewage non-concentrated alcohol explosive areas (liquid gas) lacquers Type M-ENS 4 V A 0-30 V A 0-40 V A V A Order code SVR R900 SVR R000 SVR R00 SVR R00 Accessories... /87 and /04 Technical data.../89 Technical diagrams... /0 Dimensional drawings.../03 Pack. pieces piece piece 0.5 / / / / 0.33 Version with protective separation acc. to VDE 060, n/o, n/c M-ENS 0-40 V A SVR R / 0.33 /83 D

4 M-ENS UP/DOWN SVR F00 The M-ENS UP/DOWN monitors levels of conductive liquids and other media, and is used e.g. for liquid level control in pump systems. The measuring principle is based on the resistance change sensed by single-pole electrodes. The output relay functions fill (UP) or drain (DOWN) can be selected on a front-face selector switch. If the "UP" function is selected, the output relay is energized until the MAX electrode becomes wet. Then it is de-energized and not re-energized until the electrode becomes dry. If the "DOWN" function is selected, the output relay is energized as soon as the MAX electrode becomes wet. It remains energized until the liquid level has dropped below the electrode. The electrodes can be connected to more than one M-ENS without interference. M-ENS UP/DOWN Function diagram M-ENS UP/DOWN "Func." - function selector switch: "UP"- fill "DOWN" - drain "Sens." - sensitivity potentiometer for adjusting the response sensitivity R: yellow LED - relay status U: green LED - control Marker label Max. Min. A-A -4 "DOWN" - "UP" -4 - Application examples SV F 064 onnection diagram M-ENS UP/DOWN When using a metal tank the electrode is not required. In this case the cable can be connected directly to the metal surface of the tank. Liquid level control - fill - switch position "UP" SV F 06 Liquid level control - drain - switch position "DOWN" SV F 06 A MAX MAX A A 4 4 A D 5 04 F0003 A - A Ground reference electrode MAX Maximum level Minimum level -/4 Output contacts - open-circuit or closed-circuit principle selectable ascading of electrodes The electrode inputs can be interconnected as required, which ensures simple monitoring of different liquid levels. SV F 059 Redundancy Redundant liquid level monitoring or control can be implemented by connecting the electrodes to two s. This makes the application much safer. SV F 060 Suitable for Not suitable for spring water acids, bases chemically pure water ethylene glycol drinking water liquid fertilizers fuel concentrated alcohol sea water milk, beer, coffee oils paraffin sewage non-concentrated alcohol explosive areas (liquid gas) lacquers Monitoring and control of liquid levels Selectable function "fill" or "drain" Adjustable response sensitivity 5-00 k ascadable c/o contact LEDs for status indication /84 D Type M-ENS UP/DOWN 4 V A 0-30 V A 0-40 V A Order code SVR R900 SVR R000 SVR R00 Accessories... /87 and /04 Technical data.../89 Technical diagrams... /0 Dimensional drawings.../03 Pack. pieces piece piece 0.5/ / /0.33

5 M-ENN SVR F0000 The M-ENN monitors levels of conductive liquids and is used for example for liquid level monitoring in pump control systems, for dry-running protection of submersible pumps or overflow monitoring of tanks. It is also suitable for conductivity monitoring of liquids. The measuring principle is based on the resistance change sensed by single-pole electrodes (wet or dry). Instead of electrodes, other sensors or transducers can also be used if their output quantities are different resistance values. The measuring, output and supply circuits are electrically isolated for potential separation and to prevent electrical interference. Due to the integrated ON- or OFF-delay, it is possible to set up time-dependent liquid controls using only two electrodes (, MAX). Different liquid levels in one tank can be controlled by up to 5 M-ENN (A version) without mutual interference. M-ENN Function diagrams M-ENN ircuit with electrodes ircuit with 3 electrodes "Function" - time function selector switch: A ON-delay B OFF-delay "Sens.-sector" - measuring range selector switch "Sens. " - sensitivity potentiometer for adjusting the response sensitivity "Time value" - fine adjustment of time delay R: yellow LED - relay status U: green LED - control Marker label MAX A-A 5/8 5/6 or SV F 065 SV F 067 MAX A-A 5/8 5/6 t A = ON-delay, t R = OFF-delay When using a metal tank the electrode is not required. In this case the cable can be connected directly to the metal surface of the tank. Application examples fill drain SV F 066 or onnection diagram M-ENN SV F 069 SV F 068 For commissioning, set both potentiometers (response sensitivity = R value and ON-delay = time value) to the minimum value (5) and select a suitable resistance range (sector). After all electrodes have been wetted by the liquid being monitored, turn the sensitivity potentiometer towards maximum value (00) until the relay energizes. If the relay does not energize, select a higher value (sector) on the device and proceed as before. Then it has to be checked if the relay de-energizes properly as soon as the electrodes and are no longer wet. Liquid levels higher than the maximum level electrode can be obtained by setting an ON-delay (TA = s). Liquid levels lower than the minimum level electrode can be obtained by setting an OFF-delay time (TR = s), e.g. for emptying tanks. A-A Ground reference electrode Min. level electrode MAX Max. level electrode 5-6/8 Output contacts - 5-6/8 open-circuit principle Monitoring and control of liquid levels (when emptying or filling liquids in tanks) Monitoring and control of mixture ratios (conductivity of liquids) 3 response sensitivities from k in one 5 versions 4 V A/D - 45 V A Selectable ON- or OFFdelay 0.-0 s c/o contacts LEDs for status indication Typ M-ENN Response sensitivity 50-5 k.5-50 k k 4-40 V A/D 4 V A 0-30 V A 0-40 V A V A Max. electrode current 8 ma ma 0.5 ma Order code SVR R0000 SVR R0000 SVR R0000 SVR R0000 SVR R0000 Max. cable capacity 00 nf 0 nf 4 nf Accessories... /87 and /04 Technical data.../90 Technical diagrams... /0 Dimensional drawings.../03 Pack. pieces piece Max. cable length 000 m 00 m 0 m piece 0.30 / / / / / 0.66 /85 D

6 - Liquid level control with two alarm outputs - M-ENN UP/DOWN SVR F000 The M-ENN UP/DOWN monitors levels of conductive liquids and media and is used e.g. for liquid level control in pump systems. The measuring principle is based on the resistance change sensed by singlepole electrodes. The function of the output relay -/4 can be selected by a selector switch on the front of the to fill "UP" or drain "DOWN". If the "UP" function is selected, the output relay is energized until the MAX electrode becomes wet. Then it is de-energized and not re-energized until the electrode becomes dry. If the "DOWN" function is selected, the output relay is energized as soon as the MAX electrode becomes wet. It remains energized until the liquid level has dropped below the electrode. The electrode inputs AL and AL energize/de-energize the correspopnding output relays RAL (-) and RAL (3-3). AL opens if contact RAL (-) is wet. AL closes if contact RAL (3-3) is wet. This way, two additional alarm outputs for exceeding or dropping below the normal level can be implemented in addition to the filling levels MAX and. M-ENN UP/DOWN Function diagram M-ENN UP/DOWN "Func." - function selector switch: "UP"- fill "DOWN" - drain "Sens." - sensitivity potentiometer for adjusting the response sensitivity R AL: yellow LED - relay status AL R AL: yellow LED - relay status AL R: /MAX: yellow LED - relay status /MAX U: green LED - control Marker label AL MAX AL A-A "DOWN" -4 - "UP" -4 - SV F 07 When using a metal tank the electrode is not required. In this case the cable can be connected directly to the metal surface of the tank. Application example Electrode Relay LED AL not wet RAL (-) closed off AL wet RAL (-) open on AL wet RAL (3-3) closed off AL not wet RAL (3-3) open on Supply voltage RAL (-) closed failure RAL (3-3) off Reserve pump for emptying Pump control ("UP" or "DOWN") Reserve pump for filling onnection diagram M-ENN UP/DOWN SV F 07 A-A Ground reference electrode Minimum level electrode MAX Maximum level electrode AL Alarm electrode AL Alarm electrode -/4 Output contacts - - open-circuit or closed-circuit 3-3 principle selectable SV F 070 ascading of electrodes The electrode inputs can be interconnected as required, which ensures simple monitoring of different liquid levels. SV F 059 Redundancy Redundant liquid level monitoring or control can be implemented by connecting the electrodes to two s. This makes the application much safer. SV F 060 Liquid level relay with 5 electrode inputs Level control with integrated overflow and dry-running protection Adjustable response sensitivity 5-00 k ascadable c/o contact and n/c contacts as alarm outputs 4 LEDs for status indication /86 D Suitable for Not suitable for spring water acids, bases chemically pure water ethylene glycol drinking water liquid fertilizers fuel concentrated alcohol sea water milk, beer, coffee oils paraffin sewage non-concentrated alcohol explosive areas (liquid gas) lacquers Type M-ENN UP/DOWN 4 V A 0-30 V A 0-40 V A V A Order code SVR R000 SVR R000 SVR R000 SVR R000 Accessories... /87 and /04 Technical data.../89 Technical diagrams... /0 Dimensional drawings.../03 Pack. pieces piece piece 0.5 / / / / 0.33

7 - Accessories Electrodes, dimensional drawings ompact support M-KH-3 for 3 bar electrodes Ideally suited for use with liquid level relays M-ENS and M-ENN Wire connection by screw terminals Pull relief by M6 screwed cable glands Temperature range up to 90 Food safe material (PPH) Screw-in electrodes (M4 thread) Distance plate (M-AH-3) and locking nut (M-GM-) optionally available as an accessory M6 screwed cable gland ompact support M-KH-3 M4 thread Dimensions in mm SVR F6000 screw-in bar electrodes with M4 thread (available as an option, see below) sealing ring " thread " counter nut M-GM- (order code: SVR R8000) (optional) distance plate M-AH-3 (order code: SVR R7000) (optional) SV F 0477 Distance plate M-AH-3 spanner size 36 counter nut M-GM- distance plate M-AH-3 electrodes ounter nut M-GM- Technical data compact support Type of mounting: G " thread Mounting position: any Enclosure material: PPH Sealing: NBR 70 Temperature range: 90 max. Pressure: 0 bar max. (60 ) SV F 0475 SV F 0476 Type Description Order code Pack. piece piece piece M-KH-3 M-AH-3 M-GM- ompact support for 3 bar electrodes Distance plate for 3 bar electrodes ounter nut for " thread SVR R6000 SVR R7000 SVR R / / / 0.3 Screw-in bar electrodes for compact support M-KH-3 Suspension electrode M-HE L SV F 05 Thread M4 Material: stainless steel 304, high-grade steel 430 SV F0478 Steel electrode (X4rMoS7) with sleeve (Lupulen 60 L) suitable up to 60 max. During project engineering the compatibility of the electrode material with the medium to be supervised is to be examined! Type Length Order code Pack. piece piece piece SV F 0479 M-SE-300 M-SE-600 M-SE mm 600 mm 000 mm SVR R0000 SVR R000 SVR R / / /0.76 M-HE - SVR R /0.76 /87 D

8 M-ENE, M-ENE MAX Technical data Type M-ENE M-ENE MAX Supply circuit U S - A-A 4 V A approx..5 VA power consumption A-A 0-30 V A approx.. VA A-A 0-40 V A approx..4 VA U S tolerance % Rated frequency Hz Duty time 00 % Measuring circuit -, MAX- Monitoring function dry-running protection overflow protection Response sensitivity 0-00 k, not adjustable Maximum electrode voltage 30 V A Maximum electrode current.5 ma Electrode supply line max. cable capacity 3 nf max. cable length 30 m Timing circuit Time delay - Tripping delay fixed approx. 00 ms Indication of operational states Output relay energized R: yellow LED Output circuits 3-4 Kind of output n/o contact Operational principle ) open-circuit principle closed-circuit principle ontact material Agdo Rated operational voltage U e (IE/EN ) 50 V Mininimum switching voltage / minimum switching current - / - Maximum switching voltage 50 V Rated operational current I e A (resistive) 30 V 4 A (IE/EN ) A5 (inductive) 30 V 3 A D (resistive) 4 V 4 A D3 (inductive) 4 V A A rating Utilization category (ontrol ircuit Rating ode) B 300 (UL 508) max. rated operational voltage 300 V A max. continuous thermal current at B A max. making/breaking apparent power at B /360 VA Mechanical lifetime 30 x 0 6 switching cycles Electrical lifetime (A, 30 V, 4 A) 0.3 x 0 6 switching cycles Max. fuse rating to achieve short circuit protection General data Dimensions (W x H x D) Mounting position n/c contact - n/o contact 0 A fast-acting.5 x 78 x 78.5 mm (0.89 x 3.07 x 3.09 in) any Degree of protection enclosure / terminals IP50 / IP0 Ambient temperature range operation / storage / Mounting DIN rail (IE/EN 6075) Electrical connection Wire size fine-strand with wire-end ferrule x mm ( x 8-6 AWG) fine-strand without wire-end ferrule x -.5 mm ( x 8-6 AWG) rigid x mm ( x 8-6 AWG) Stripping length 0 mm (0.39 inch) Tightening torque Nm Standards Product standard IE 55-6, EN Low Voltage Directive 006/95/E EM Directive 004/08/E Electromagnetic compatibility EN , EN electrostatic discharge IE/EN Level 3 (6 kv / 8 kv) radiated, radio-frequency, electromagnetic field IE/EN Level 3 (0 V/m) electrical fast transient / burst IE/EN Level 3 ( kv / 5 khz) surge IE/EN Level 4 ( kv L-L) conducted disturbances, induced by radio-frequency fields IE/EN Level 3 (0 V) Resistance to vibration (IE 68--6) 6 g Mechanical resistance (IE 68--6) 0 g Isolation data Rat. insulation volt. betw. supply, meas. & output circuit (VDE 00, IE 60947) 50 V Rated impulse withstand voltage between all isolated circuits (VDE0 0, IE 664) 4 kv /.-50 μs Test voltage between all isolated circuits.5 kv, 50 Hz, min. Pollution category (VDE 00, IE 664, IE 55-5) 3 / Overvoltage category (VDE 00, IE 664, IE 55-5) III / Environmental testing (IE ) 4 h cycle time, 55, 93 % rel., 96 h ) Open-circuit principle: Output relay energizes if the measured value exceeds/drops below the adjusted threshold. losed-circuit principle: Output relay de-energizes if the measured value exceeds/drops below the adjusted threshold. Approvals... /6 /88 D

9 M-ENS, M-ENS UP/DOWN Technical data Type M-ENS M ENS UP/DOWN Supply circuit U S - power consumption A-A 4 V A 4 V A A-A 0-30 V A approx..5 VA 0-30 V A approx. 4 VA A-A 0-40 V A approx..5 VA 0-40 V A approx. 4 VA A-A V A approx..5 VA U S tolerance % Rated frequency Hz Duty time 00 % Measuring circuit MAX-- Monitoring function liquid level control Response sensitivity 5-00 k, adjustable Maximum electrode voltage 30 V A Maximum electrode current ma Electrode supply line max. cable capacity 0 nf max. cable length 00 m Timing circuit Time delay - Tripping delay approx. 50 ms Indication of operational states ontrol U: green LED Output relay energized R MAX/: yellow LED Alarm relay AL - R AL: yellow LED Alarm relay AL - R AL: yellow LED Output circuits -/4, -, 3-3 Kind of output c/o contact, n/o + n/c contact ) Operational principle ) open-circuit principle open- and closed-circuit principle ontact material Agdo Rated operational voltage U e (IE/EN ) 50 V Minimum switching voltage / minimum switching current - / - Maximum switching voltage 50 V Rated operational current I e A (resistive) 30 V 4 A (IE/EN ) A5 (inductive) 30 V 3 A D (resistive) 4 V 4 A D3 (inductive) 4 V A A rating Utilization category (ontrol ircuit Rating ode) B 300 (UL 508) max. rated operational voltage 300 V A max. continuous thermal current at B A max. making/breaking apparent power at B /360 VA Mechanical lifetime 30 x 0 6 switching cycles Electrical lifetime (A, 30 V, 4 A) 0.3 x 0 6 switching cycles Max. fuse rating to achieve short circuit protection n/c / n/o contact 0 A (4 A ) ) fast-act. / 0 A (6 A ) ) fast-act. 0 A fast-acting / 0 A fast-acting General data Dimensions (W X H X D).5 x 70 x 00 mm (0.89 x 3.07 x 3.94 in) Mounting position any Degree of protection enclosure / terminals IP50 / IP0 Ambient temperature range operation / storage / Mounting DIN rail (IE/EN 6075) Electrical connection Wire size fine-strand with wire end ferrule x.5 mm ( x 4 AWG) Standards Product standard IE 55-6, EN Low Voltage Directive 006/95/EG EM Directive 004/08/EG Electromagnetic compatibility - electrostatic discharge IE/EN Level 3 (6 kv / 8kV) radiated, radio-frequency, electromagnetic field IE/EN Level 3 (0 V/m) electrical fast transient / burst IE/EN Level 3 ( kv / 5 khz) surge IE/EN Level 4 ( kv L-L) conducted disturbances, induced by radio-frequency fields IE/EN Level 3 (0 V) Resistance to vibration (IE 68--6) 4 g Mechanical resistance (IE 68--6) 6 g Isolation data Rated insulation voltage between supply, measuring and output circuit (VDE 00, IE 60947) 50 V Rated impulse withstand voltage between all isolated circuits (VDE0 0, IE 664) 4 kv / μs Test voltage between all isolated circuits,5 kv, 50 Hz, min. Pollution category (VDE 00, IE 664, IE 55-5) 3 / Overvoltage category (VDE 00, IE 664, IE 55-5) III / Environmental testing (IE ) 4 h cycle time, 55, 93 % rel., 96 h ) Open-circuit principle: Output relay energizes if the measured value exceeds/drops below the adjusted threshold. losed-circuit principle: Output relay de-energizes if the measured value exceeds/drops below the adjusted threshold. ) SVR R300 (version with safe isolation) Approvals... /6 /89 D

10 M-ENN UP/DOWN, M-ENN Technical data Type M-ENN UP/DOWN M-ENN Supply circuit U S - power consumption A-A 4 V A 4 V A A-A 0-30 V A approx..5 VA 0-30 V A approx..5 VA A-A 0-40 V A approx..5 VA 0-40 V A approx. 3 VA A-A V A approx..5 VA V Aapprox. 4 VA A-A 4-40 V A/D approx. VA/W U S tolerance % Rated frequency Hz Hz oder D Duty time 00 % Measuring circuit MAX-- Monitoring function liquid level control Response sensitivity adjustable adjustable 5-00 k 50-5 k.5-50 k k Maximum electrode voltage 30 V A 0 V A Maximum electrode current ma 8 ma ma 0.5 ma Electrode supply line max. cable capacity 0 nf 00 nf 0 nf 4 nf max. cable length 00 m 000 m 00 m 0 m Timing circuit Time delay s, adjustable, ON- or OFF-delay Tripping delay approx. 50 ms - Indication of operational states ontrol U: green LED Output relay energized R MAX/: yellow LED R: yellow LED Output circuits -/4, -, /8, 5-6/8 Kind of output c/o + n/c contacts c/o contacts Operational principle ) open-circuit principle open- and closed-circuit principle ontact material Agdo Rated operational voltage U e (IE/EN ) 50 V 400 V Minimum switching voltage / minimum switching current - / - Maximum switching voltage 50 V 400 V Rated operational current I e (IE/EN ) A rating (UL 508) A (resistive) 30 V 4 A 5 A A5 (inductive) 30 V 3 A D (resistive) 4 V 4 A 5 A D3 (inductive) 4 V A.5 A Utilization category (ontrol ircuit Rating ode) B 300 max. rated operational voltage 300 V A max. continuous thermal current at B A max. making/breaking apparent power at B /360 VA 30 x 0 6 switching cycles Mechanical lifetime Electrical lifetime (A, 30 V, 4 A) 0.3 x 0 6 switching cycles 0. x 0 6 switching cycles Max. fuse rating to achieve short circuit protection n/c / n/o contact 4 A fast-acting / 6 A fast-acting General data Diemensions (W X H X D) 45 x 78 x 00 mm (.77 x 3.07 x 3.94 in) Mounting position any Degree of protection enclosure / terminals IP50 / IP0 Ambient temperature range operation / storage / Mounting DIN rail (IE/EN 6075) Electrical connection Wire size fine-strand with wire end ferrule x.5 mm ( x 4 AWG) Standards Product standard IE 55-6, EN Low Voltage Directive 006/95/EG EM Directive 004/08/EG Electromagnetic compatibility - electrostatic discharge IE/EN Level 3 (6 kv / 8kV) radiated, radio-frequency, electromagnetic field IE/EN Level 3 (0 V/m) electrical fast transient / burst IE/EN Level 3 ( kv / 5 khz) surge IE/EN Level 4 ( kv L-L) conducted disturbances, induced by radio-frequency fields IE/EN Level 3 (0 V) Resistance to vibration (IE 68--6) 5 g Mechanical resistance (IE 68--6) 0 g Isolation data Rated insulation voltage between supply, measuring and output circuit (VDE 00, IE 60947) 50 V 500 V Rated impulse withstand voltage between all isolated circuits (VDE0 0, IE 664) 4 kv / μs Test voltage between all isolated circuits,5 kv, 50 Hz, min. Pollution category (VDE 00, IE 664, IE 55-5) 3 / Overvoltage category (VDE 00, IE 664, IE 55-5) III / Environmental testing (IE ) 4 h cycle time, 55, 93 % rel., 96 h ) Open-circuit principle: Output relay energizes if the measured value exceeds/drops below the adjusted threshold. losed-circuit principle: Output relay de-energizes if the measured value exceeds/drops below the adjusted threshold. Approvals... /6 /90 D

Thermistor motor protection relays

Thermistor motor protection relays Thermistor motor protection relays Content Benefits and advantages... / 68 Selection table... / 68 Ordering details CM-MSE... / 69 CM-MSS... / 69 CM-MSN... / 7 PTC sensor C0... / 7 Technical data... /

More information

Liquid level monitoring relay CM-ENS.2x

Liquid level monitoring relay CM-ENS.2x Data sheet Liquid level monitoring relay CM-ENS.2x The CM-ENS.2x is served to regulate and control liquid levels and ratios of mixtures of conductive fluids. It can be used for overflow protection, dry

More information

Three-phase monitoring relay CM-PVE

Three-phase monitoring relay CM-PVE Data sheet Three-phase monitoring relay CM-PVE The three-phase monitoring relay CM-PVE monitors the phase parameter phase failure as well as over- and undervoltage in three-phase mains. 2CDC 251 006 S0012

More information

Current monitoring relays CM-SRS.2 for single-phase AC/DC currents

Current monitoring relays CM-SRS.2 for single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.2 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages

Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages Data sheet Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages For the monitoring of voltages in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Three-phase monitoring relay

Three-phase monitoring relay 1SR 430 824 F9300 Features Monitoring of three-phase mains for phase sequence and failure Powered by the measuring circuit 2 c/o (SPDT) contacts 1 LED for status indication Approvals R: yellow LED - relay

More information

Three-phase monitoring relays CM-PFE and CM-PFE.2

Three-phase monitoring relays CM-PFE and CM-PFE.2 Data sheet Three-phase monitoring relays CM-PFE and CM-PFE.2 The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251

More information

Three-phase monitoring relays

Three-phase monitoring relays 2CDC 251 046 F0t08 Features Monitoring of three-phase mains for phase sequence, phase failure, phase unbalance Threshold value for phase unbalance adjustable as absolute value Tripping delay can be adjusted

More information

Type CP-S, CP-C & CP-A Switch mode

Type CP-S, CP-C & CP-A Switch mode Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting

More information

Current monitoring relays CM-SRS.1 for single-phase AC/DC currents

Current monitoring relays CM-SRS.1 for single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.1 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact

Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact Data sheet Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact The CT-TGD.12 is an electronic time relay with the function pulse generator. It is from the CT-D range. With their MDRC profile

More information

ABB NEW. Three-phase monitoring relays. CM-PVS.31 and CM-PVS.41 Data sheet. Features J. Approvals. Marks. Order data. Order data - Accessories

ABB NEW. Three-phase monitoring relays. CM-PVS.31 and CM-PVS.41 Data sheet. Features J. Approvals. Marks. Order data. Order data - Accessories 2CDC 251 042 F0t08 CM-PVS.31 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage Threshold values for over- and undervoltage are adjustable

More information

Measuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC

Measuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC 2CDC 251 244 F0t05 Characteristics Monitoring of DC and AC currents: RMS measuring principle One device includes 3 measuring ranges Over- or undercurrent monitoring configurable Hysteresis adjustable from

More information

Electronic timer CT-SDS.22

Electronic timer CT-SDS.22 CDC 0 F0t07 Features Rated control supply voltage 8 V DC, 0 V AC Single function timer with star delta change over One device includes 7 time ranges (0.0 s 0 min) n/o contacts LEDs for status indication

More information

Electronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet

Electronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet CDC 0 F0t07 Features Rated control supply voltage -8 V DC, -0 V AC Single-function timer with star-delta change-over One device includes 7 time ranges (0.0 s - 0 min) n/o contacts LEDs for status indication

More information

Thermistor motor protection relays

Thermistor motor protection relays Thermistor motor protection relays Content Benefits and advantages... / 68 Selection table... / 68 Ordering details CM-MSE... / 69 CM-MSS... / 69 CM-MSN... / 7 PTC sensor C0... / 7 Technical data... /

More information

Electronic timer CT-SDE Star-delta change-over with 1 n/c + 1 n/o contact

Electronic timer CT-SDE Star-delta change-over with 1 n/c + 1 n/o contact Data sheet Electronic timer CT-SDE Star-delta change-over with n/c + n/o contact The CT-SDE is an electronic time relay with star-delta change-over. It is from the CT-E range. The CT-E range is the economic

More information

Electronic timer CT-EBE Flasher starting with OFF, 1 c/o (SPDT) contact

Electronic timer CT-EBE Flasher starting with OFF, 1 c/o (SPDT) contact Data sheet Electronic timer CT-EBE Flasher starting with OFF, 1 c/o (SPDT) contact The CT-EBE is an electronic time relay with the function flasher starting with OFF. It is from the CT-E range. The CT-E

More information

Electronic timer CT-ERS ON-delayed with 2 c/o contacts Data sheet

Electronic timer CT-ERS ON-delayed with 2 c/o contacts Data sheet 1SVR 430 103 F0200 CT-ERS 1 7 2 6 5 4 8 3 1 10 selectable time ranges, from 0.05 s to 300 h 2 Potentiometer with direct reading scale for the fine adjustment of the time delay 3 Sliding switch to set the

More information

Three-phase monitoring relay

Three-phase monitoring relay 1SR 550 870 F9400 Features Monitoring of three-phase mains for phase failure, over- and undervoltage Device with possibility of neutral monitoring available Device with suitability for monitoring single-phase

More information

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with true OFF-delay and 10 time ranges. All electronic timers from

More information

ABB 1. Multifunctional three-phase monitoring relays. CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. Features. Approvals. Marks.

ABB 1. Multifunctional three-phase monitoring relays. CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. Features. Approvals. Marks. 2CDC 251 048 F0t08 CM-MPS.11 2CDC 251 049 F0t08 CM-MPS.21 2CDC 251 050 F0t08 CM-MPS.31 2CDC 251 051 F0t08 CM-MPS.41 R/T: yellow LED - relay status, timing F1: red LED - fault message F2: red LED - fault

More information

Electronic timer CT-AWS Impulse-OFF with 1 c/o contact Data sheet

Electronic timer CT-AWS Impulse-OFF with 1 c/o contact Data sheet 2CDC 251 121 F0004 1 5 2 4 3 6 Characteristics Single-function impulse-off timer One device includes 10 time ranges, from 0.05 s to 300 h, for the adjustment of the pulse time Remote potentiometer connection

More information

CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. UL 508, CAN/CSA C22.2 No.14 GL GOST CB scheme CCC

CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. UL 508, CAN/CSA C22.2 No.14 GL GOST CB scheme CCC 2CDC 251 048 F0t08 CM-MPS.11 2CDC 251 049 F0t08 CM-MPS.21 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage as well as phase unbalance

More information

Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)

Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,

More information

Current monitoring relays CM-SRS.2 For single-phase AC/DC currents

Current monitoring relays CM-SRS.2 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.2 For single-phase AC/DC currents The CM-SRS.2 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent

More information

Electronic timer CT-TGD.22

Electronic timer CT-TGD.22 2CDC 251 097 F0t06 a Rotary switch for the preselection of the time range of the ON time b Potentiometer with direct reading scale for the fine adjustment of the ON time c Rotary switch for the preselection

More information

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with OFF-delay and 10 time ranges. All electronic timers from the CT-S

More information

Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages

Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

Sensitivity range ( ) kω adjustable Delay time (0.5s or 7s) switch selectable Emptying or filling functions switch selectable

Sensitivity range ( ) kω adjustable Delay time (0.5s or 7s) switch selectable Emptying or filling functions switch selectable 72 Series - Monitoring relays 16 A Features 72.01 72.11 Level control relays for conductive liquids 72.01 - Adjustable sensitivity 72.11 - Fixed sensitivity Emptying or filling functions LED indicator

More information

Current monitoring relays CM-SRS.1 For single-phase AC/DC currents

Current monitoring relays CM-SRS.1 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.1 For single-phase AC/DC currents The CM-SRS.1 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent

More information

ABB 1. Multifunctional three-phase monitoring relays. CM-MPN.52, CM-MPN.62 and CM-MPN.72 Data sheet. Features. Approvals. Marks.

ABB 1. Multifunctional three-phase monitoring relays. CM-MPN.52, CM-MPN.62 and CM-MPN.72 Data sheet. Features. Approvals. Marks. 2CDC 251 054 F0t08 CM-MPN.52 2CDC 251 055 F0t08 CM-MPN.62 2CDC 251 056 F0t08 CM-MPN.72 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage

More information

Electronic timer CT-SDD.22

Electronic timer CT-SDD.22 CDC 099 F0t0 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied W

More information

Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages

Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages Data sheet Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages The CM-EFS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

Electronic timer CT-YDE Star-delta change-over with 1 c/o (SPDT) contact

Electronic timer CT-YDE Star-delta change-over with 1 c/o (SPDT) contact Data sheet Electronic timer CT-YDE Star-delta change-over with c/o (SPDT) contact The CT-YDE is an electronic time relay with star-delta change-over. It is from the CT-E range. The CT-E range is the economic

More information

Three-phase monitoring relay CM-PBE

Three-phase monitoring relay CM-PBE Data sheet Three-phase monitoring relay CM-PBE The three-phase monitoring relay CM-PBE monitors the phase parameter phase failure in three-phase mains. 2CDC 251 007 S0012 Characteristics Monitoring of

More information

Three-phase monitoring relays CM-PVS.81

Three-phase monitoring relays CM-PVS.81 Data sheet Three-phase monitoring relays CM-PVS.81 The three-phase monitoring relay CM-PVS.81 monitors the phase parameters phase sequence, phase failure as well as over- and undervoltage. The device is

More information

Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41

Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41 Data sheet Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41 The three-phase monitoring relays CM-PSS.x1 monitor the phase parameters phase sequence, phase failure as well as over- and undervoltage.

More information

Three-phase monitoring relays CM-PVS CM-PVS.31, CM-PVS.41 and CM-PVS.81

Three-phase monitoring relays CM-PVS CM-PVS.31, CM-PVS.41 and CM-PVS.81 Data sheet Three-phase monitoring relays CM-PVS CM-PVS.31, CM-PVS.41 and CM-PVS.81 The three-phase monitoring relays CM-PVS.x1 monitor the phase parameters phase sequence, phase failure as well as over-

More information

ABB NEW. Multifunctional three-phase monitoring relays. CM-MPS.23 and CM-MPS.43 Data sheet. Features J. Approvals. Marks.

ABB NEW. Multifunctional three-phase monitoring relays. CM-MPS.23 and CM-MPS.43 Data sheet. Features J. Approvals. Marks. 2CDC 251 052 F0t08 CM-MPS.23 2CDC 251 053 F0t08 CM-MPS.43 - relay status, timing - fault message - fault message Adjustment of the tripping delay t V Adjustment of the threshold value for overvoltage 6

More information

Sensitivity range ( ) kω adjustable Delay time (0.5s or 7s) switch selectable Emptying or filling functions switch selectable

Sensitivity range ( ) kω adjustable Delay time (0.5s or 7s) switch selectable Emptying or filling functions switch selectable Features 72.01 72.11 Level control relays for conductive liquids 72.01 - Adjustable sensitivity 72.11 - Fixed sensitivity Emptying or filling functions LED indicator Reinforced insulation (6 kv - 1.2/50

More information

Sensitivity range ( ) kω adjustable Delay time (0.5s or 7s) switch selectable Emptying or filling functions switch selectable

Sensitivity range ( ) kω adjustable Delay time (0.5s or 7s) switch selectable Emptying or filling functions switch selectable Features Level control relays for conductive liquids 72.01 - Adjustable sensitivity 72.11 - Fixed sensitivity Emptying or filling functions LED indicator Reinforced insulation (6 kv - 1.2/50 µs) between:

More information

Electronic timer CT-MVS.12 Multifunctional with 1 c/o (SPDT) contact

Electronic timer CT-MVS.12 Multifunctional with 1 c/o (SPDT) contact Data sheet Electronic timer CT-MVS.12 Multifunctional with 1 c/o (SPDT) contact The CT-MVS.12 is a multifunctional electronic timer from the CT-S range and provides 10 timing functions and 10 time ranges.

More information

Electronic timer CT-MFS.21

Electronic timer CT-MFS.21 2CDC 251 053 F0t07 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c Rotary switch for the preselection of the

More information

Electronic timer CT-WBS.22 Impulse generating and flashing with 2 c/o (SPDT) contacts

Electronic timer CT-WBS.22 Impulse generating and flashing with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-WBS.22 Impulse generating and flashing with 2 c/o (SPDT) contacts The CT-WBS.22 is a multifunctional electronic timer from the CT-S range. It provides 10 timing functions

More information

Subject to changes 11/2003 Page 1/7

Subject to changes 11/2003 Page 1/7 Main Characteristics: Zero switching. LED display. Various connection systems. Plug-in control terminal. Degree of protection IP 2. Double-insulated design. General Data: Standards / Approvals DIN EN 697--3

More information

Three-phase monitoring relay CM-PFS

Three-phase monitoring relay CM-PFS Data sheet Three-phase monitoring relay CM-PFS The CM-PFS is a three-phase monitoring relay that is used to monitor three phase mains for incorrect phase sequence and phase failure. All devices are available

More information

Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents

Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents The CM-SRS.M1 is an electronic current monitoring relay that monitors single-phase mains (DC or AC) for over- and undercurrent

More information

Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages

Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages Data sheet Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages The CM-ESS.M is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts The CT-MVS.23 is a multifunctional electronic timer from the CT-S range. It provides 11 timing functions and 10 time ranges.

More information

V2UM230V10 Art.Nr.: V2UM230V10P Art.Nr.: Control elements. Tripping delay. Function selector. Status indication 230 V AC/DC

V2UM230V10 Art.Nr.: V2UM230V10P Art.Nr.: Control elements. Tripping delay. Function selector. Status indication 230 V AC/DC P AC/DC voltage monitoring Multifunction Supply voltage 24 V DC or 230V AC/DC Supply circuit = Measuring circuit 1 change-over contact Width 22,5 mm Control elements Tripping delay Maximum threshold Minimum

More information

VEO. V2PF480Y/277VS01 Art.Nr.: B TECHNICAL DATA

VEO. V2PF480Y/277VS01 Art.Nr.: B TECHNICAL DATA Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Status indication LED U: Supply voltage

More information

Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23

Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 Data sheet Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 The three-phase monitoring relay CM-MPS.23 monitors the phase parameters phase sequence, phase failure, over- and undervoltage

More information

Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 and CM-MPS.43

Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 and CM-MPS.43 Data sheet Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 and CM-MPS.43 The three-phase monitoring relays CM-MPS.x3 monitor the phase parameters phase sequence, phase failure, over- and

More information

Analog signal converters CC range

Analog signal converters CC range Analog signal converters CC range Benefits and advantages 2CDC 28 Fb Product range for analog signal processing CC-U range 8 different standard signal outputs on one device Input and output side universally

More information

Multifunctional three-phase monitoring relays CM-MPN CM-MPN.52, CM-MPN.62 and CM-MPN.72

Multifunctional three-phase monitoring relays CM-MPN CM-MPN.52, CM-MPN.62 and CM-MPN.72 Data sheet Multifunctional three-phase monitoring relays CM-MPN CM-MPN.52, CM-MPN.62 and CM-MPN.72 The three-phase monitoring relays CM-MPN.x2 monitor the phase parameters phase sequence, phase failure,

More information

VEO. V2PF480Y/277VSY01 Art.Nr.: V2PF480Y/277VSY01P Art.Nr.: TECHNICAL DATA

VEO. V2PF480Y/277VSY01 Art.Nr.: V2PF480Y/277VSY01P Art.Nr.: TECHNICAL DATA P Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Control elements Asymmetry Status

More information

Electronic timer CT-AHE OFF-delayed with 1 c/o (SPDT) contact

Electronic timer CT-AHE OFF-delayed with 1 c/o (SPDT) contact Data sheet Electronic timer CT-AHE OFF-delayed with 1 c/o (SPDT) contact The CT-AHE is an electronic time relay with OFF-delay. t is from the CT-E range. The CT-E range is the economic range of ABB s time

More information

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts The CT-MVS.22 is a multifunctional electronic timer from the CT-S range. It provides 11 timing functions and 10 time ranges.

More information

Three-phase monitoring relays Product group picture

Three-phase monitoring relays Product group picture Product group picture /7 ABB Catalog Electronic Products and Relays 013/014 CDC 110 004 C009 Table of contents Three-phase monitoring relays Product group picture 7 Table of contents 8 Benefits and advantages,

More information

s s s 3-60 s min min 3-60 min h h 3-60 h V AC, 50/60 Hz

s s s 3-60 s min min 3-60 min h h 3-60 h V AC, 50/60 Hz HPL11002EN DILETTiming relays Rated operational current AC-11 230 V 400 V I th I e I e A A A A A Conventional thermal current Time Range Voltage Article No. See price list Std. pack On-delayed Timing functions

More information

Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts The CT-MXS.22 is a multifunctional electronic timer from the CT-S range. It provides 5 timing functions, 2 times 10 time

More information

Electronic measuring and monitoring relays CM-range

Electronic measuring and monitoring relays CM-range Electronic measuring and CM-range Content Benefits and advantages CM range, function overview... 30 Selection and ordering details Current and voltage monitors, single phase... 33 Three phase monitors...

More information

Power supply CP-D 24/4.2 Primary switch mode power supply

Power supply CP-D 24/4.2 Primary switch mode power supply Data sheet Power supply CP-D 24/4.2 Primary switch mode power supply The CP-D range of modular power supply units in MDRC design (modular DIN rail components) is ideally suited for installation in distribution

More information

Electronic timer CT-AWE Impulse-OFF with auxiliary voltage, 1 c/o (SPDT) contact

Electronic timer CT-AWE Impulse-OFF with auxiliary voltage, 1 c/o (SPDT) contact Data sheet Electronic timer CT-AWE mpulse-off with auxiliary voltage, 1 c/o (SPDT) contact The CT-AWE is an electronic time relay with mpulse-off function. t is from the CT-E range. The CT-E range is the

More information

V2IM10AL10 Art.Nr.: V2IM10AL10P Art.Nr.: Control element. Tripping delay. Function selector. Status indication 24...

V2IM10AL10 Art.Nr.: V2IM10AL10P Art.Nr.: Control element. Tripping delay. Function selector. Status indication 24... P AC/DC current monitoring Multifunction Supply voltage 24-240V DC or 110-240V AC 1 change-over contact Width 22,5 mm Control element Tripping delay Maximum threshold Minimum threshold Function selector

More information

ABB ABB 59 2CDC110004C0205. Measuring and monitoring relays. CM and C5xx range. Content

ABB ABB 59 2CDC110004C0205. Measuring and monitoring relays. CM and C5xx range. Content ABB Measuring and monitoring relays CM and C5xx range Content Benefits and advantages, overview of features... 60 Approvals and marks... 64 Current and voltage monitors, single-phase... 65 Ordering details...

More information

Three-phase monitoring relays Table of contents

Three-phase monitoring relays Table of contents Table of contents Three-phase monitoring relays Three-phase monitoring relays 78 Benefits and advantages, Applications 79 Operating controls 80 Selection table - Singlefunctional 81 Ordering details -

More information

Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC

Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC Data sheet Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC The CM-IWS.1 serves to monitor insulation resistance in accordance with IEC

More information

Three-phase monitoring relays Product group picture

Three-phase monitoring relays Product group picture Product group picture /7 ABB Catalog Electronic Products and Relays 015 CDC 110 004 C010 Table of contents Three-phase monitoring relays Benefits and advantages, Applications /9 Operating controls /30

More information

Power supply CP-E 24/20.0

Power supply CP-E 24/20.0 2CDC 271 027 F0008 a OUTPUT L+, L+, L, L-: terminals output b INPUT L, N, PE: terminals input c 13-14: terminals - signalling contact d OUTPUT OK: green LED output voltage OK e OUTPUT LOW: red LED output

More information

Multi-function (MI, ME, M2, M1) 2 NO (2 SPST-NO) 12 / / 400 3,000 1, / 0.3 / (5 / 5) AgNi

Multi-function (MI, ME, M2, M1) 2 NO (2 SPST-NO) 12 / / 400 3,000 1, / 0.3 / (5 / 5) AgNi Features Special relay for alternating loads, for applications with pumps, compressors, air conditioning or refrigeration units 2 independent NO output, 12 A 4 functions 2 independent control signals,

More information

Control module CP-A CM

Control module CP-A CM 2CDC 271 002 F0t05 Features Pluggable onto redundancy unit CP A RU Threshold values adjustable (14 28 V) One relay output per monitored input / channel Approvals H UL 508, CAN/CSA C22.2 No.14 H UL 60950,

More information

Electronic timer CT-MBS.22 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MBS.22 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MBS.22 Multifunctional with 2 c/o (SPDT) contacts The CT-MBS.22 is a multifunctional electronic timer from the CT-S range. It provides 10 timing functions and 10 time ranges.

More information

Electronic timer CT-MFS.21 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MFS.21 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MFS.21 Multifunctional with 2 c/o (SPDT) contacts The CT-MFS.21 is a multifunctional electronic timer from the CT-S range. It provides 10 timing functions, 10 time ranges

More information

3RF A A 0 2. Switching function. Control voltage Operating voltage with heat sink 10 = 10.5 A. A = Zero-point switching

3RF A A 0 2. Switching function. Control voltage Operating voltage with heat sink 10 = 10.5 A. A = Zero-point switching Main Characteristics: Zero-point switching LED display Various connection technologies Plug-in control terminal Degree of protection IP 2 Insulated mounting foot Standards / Approvals: DIN EN 697--3 UL

More information

Power supply CP-E 24/2.5

Power supply CP-E 24/2.5 2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment

More information

CP-T range Product group picture

CP-T range Product group picture Product group picture /1 ABB Catalog Electronic Products and Relays 1/1 2CDC 110 00 C09 Table of contents CP-T range Product group picture /1 Table of contents /2 Benefits and advantages / Ordering details

More information

Power supply CP-E 24/0.75

Power supply CP-E 24/0.75 2CDC 271 016 F0t06 a OUTPUT L+, L : terminals output b INPUT L, N, PE: terminals input c LOW: red LED output voltage too low d OK: green LED output voltage OK e OUTPUT Adjust: rotary potentiometer output

More information

Switching power supplies CP range, Linear power supplies CP-L range. Content

Switching power supplies CP range, Linear power supplies CP-L range. Content CP range, Linear power supplies CP-L range Content Switching power supplies, primary switch mode, CP range Benefits and advantages... 136 Approvals... 137 Ordering details... 138 Technical data... 11 Dimensional

More information

Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC

Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC Data sheet Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC The CM-IVN serves to extend the measuring range of the insulation

More information

Power supply CP-D 12/2.1

Power supply CP-D 12/2.1 2CDC 271 025 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 12 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 2.1 A Rated output power

More information

Electronic timers CT-S range Selection and ordering details

Electronic timers CT-S range Selection and ordering details CT-S range Selection and ordering details Characteristics CT-S range CT-MFS 1SVR 430 010 F 0200 3 multifunction and 21 multi-range Continuous supply voltage range (24-240VAC/DC) or multisupply voltage

More information

Control module CP-A CM

Control module CP-A CM Control module 2CDC 271 002 F0t05 Features Pluggable onto redundancy unit CP-A RU Adjustable threshold values (14-28 V) and relay outputs per input / channel Approvals Marks g 6 7 1 3 4 2 8 5 Order data

More information

CP-E range Benefits and advantages

CP-E range Benefits and advantages Benefits and advantages Characteristics Output voltages 5 V, 12 V, 2 V, 8 V DC Adjustable output voltages Benefits Signalling output/contact Output currents 0.625 A / 0.75 A / 1.25 A / 2.5 A / A / 5 A

More information

48 Series - Relay interface modules A. Features

48 Series - Relay interface modules A. Features Series - Relay interface modules 8-0 - 6 A Features & Pole relay interface modules, 5.8 mm wide. Ideal interface for PLC and electronic systems.3 - Pole 0 A.5 - Pole 8 A.6 - Pole 6 A coils or sensitive

More information

Moeller Electric Corporation

Moeller Electric Corporation EMR4-I Current Monitoring Relays 02/0053 EMR4-I1-2-A EMR4-I15-2-A EMR4-I15-2-B Mechanical lifespan operations x10 6 30 30 30 24-h cycle, 55 C, 93 % relative humidty, 96 h Ambient temperature min./max.

More information

Power supply CP-D 24/1.3

Power supply CP-D 24/1.3 2CDC 271 027 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 24 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 1.3 A Rated output power

More information

38 Series - Relay interface modules A

38 Series - Relay interface modules A 38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical Relays

More information

Power supply CP-E 24/2.5

Power supply CP-E 24/2.5 2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment

More information

Power supply CP-E 12/10.0 Primary switch mode power supply Data sheet

Power supply CP-E 12/10.0 Primary switch mode power supply Data sheet 2CDC 271 024 F0008 OUTPUT L+, L+, L-, L-: terminals - output INPUT L, N, PE: terminals - input OUTPUT OK: green LED - output voltage OK OUTPUT LOW: red LED - output voltage too low OUTPUT Adjust: potentiometer

More information

38 Series - Relay interface modules A

38 Series - Relay interface modules A 38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit 6.2 mm wide EMR - DC, AC or AC/DC

More information

CP-T range Benefits and advantages

CP-T range Benefits and advantages Benefits and advantages Characteristics Rated output voltages V, V DC Output voltage adjustable via front-face rotary potentiometer OUTPUT Adjust Rated output currents 5 A, 10 A, A, A Rated output powers

More information

Electronic timer CT-SDE

Electronic timer CT-SDE CDC 51 059 F000 1 Characteristics " 1 single time range from 0. to 0 s " versions with different supply voltage ranges are available: 4 AC/DC and 110-10 AC and 80-415 AC " Single-function timer with star-delta

More information

Power supply CP-T 24/20.0 Primary switch mode power supply

Power supply CP-T 24/20.0 Primary switch mode power supply Data sheet Power supply CP-T 24/20.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

Electronic timer CT-MFS.21 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MFS.21 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MFS.21 Multifunctional with 2 c/o (SPDT) contacts The CT-MFS.21 is a multifunctional electronic timer from the CT-S range. It provides 10 timing functions, 10 time ranges

More information

Power supply CP-T 24/10.0 Primary switch mode power supply

Power supply CP-T 24/10.0 Primary switch mode power supply Data sheet Power supply CP-T 24/10.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

Power supply CP-T 24/40.0 Primary switch mode power supply

Power supply CP-T 24/40.0 Primary switch mode power supply Data sheet Power supply CP-T 24/40.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

38 SERIES. Relay interface modules A. EMR Electromechanical Relays. Common features. SSR Solid State Relays. 6.

38 SERIES. Relay interface modules A. EMR Electromechanical Relays. Common features. SSR Solid State Relays. 6. 38 Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit 6.2 mm wide EMR - DC, AC or AC/DC

More information

Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC

Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC Data sheet Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC The CM-IVN serves to extend the measuring range of the insulation

More information