Japan Test Report. : BTv4.0 Dual Mode USB HCI Module BTv4.0 Dual Mode USB HCI Module External Antenna variant

Transcription

1 Japan Test Report Equipment Model No. Brand Name Applicant : BTv4.0 Dual Mode USB HCI Module BTv4.0 Dual Mode USB HCI Module External Antenna variant : BT800 BT800-ST (Please refer to section for more details.) : Laird Technologies : Laird Technologies Address : Thompson Ave. / Lenexa, Kansas / / USA Standard : ARIB STD-T66 Ver. 3.7 Received Date : Jul. 29, 2015 Tested Date : Jul. 29, 2015 Measurement was conducted by the following test method: the test method of Ordinance Concerning Technical Regulations Conformity Certification etc. of Specified Radio Equipment in Annex 1, the Ministry of Internal Affairs and Communication notification in Annex 43 of Article 88, Paragraph 1 or the test method more than equivalent. We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Gary Chang / Manager Ty: XXX Report No.: JR AD Page No. : 1 of 19 Report Version: Rev. 03

2 Table of Contents 1 GENERAL DESCRIPTION Information Test Equipment and Calibration Data Testing Applied Standards Measurement Uncertainty TEST CONFIGURATION Testing Location and Conditions Supporting Units The Worst Test Modes and Channel Details TRANSMITTER TEST RESULTS Antenna Power Frequency Tolerance Occupied Bandwidth Spreading Bandwidth and Factor Transmitter Spurious Emissions Dwell time Interference prevention function RECEIVER TEST RESULTS Receiver Spurious Emissions PHOTOGRAPHS OF THE TEST CONFIGURATION TEST LABORATORY INFORMATION APPENDIX A. TEST RESULTS... A1 APPENDIX B. ANTENNA INFORMATION... B1 Report No.: JR AD Page No. : 2 of 19 Report Version: Rev. 03

3 Release Record Report No. Version Description Issued Date JR AD Rev. 01 Initial issue Aug. 10, 2015 JR AD Rev. 02 Appendix A data modified. Sep. 02, 2015 JR AD Rev. 03 Rated power modified (page 5) Sep. 07, 2015 Report No.: JR AD Page No. : 3 of 19 Report Version: Rev. 03

4 Summary of Test Results Ref. Std. Clause Description Result 3.2(2)(3) Antenna Power / Tolerances for antenna power Pass 3.2(4) Frequency Tolerance Pass 3.2(6) Transmitter Spurious Emission Pass 3.2(7) Occupied Bandwidth Pass 3.2(8) Spreading Bandwidth Pass 3.2(9) Spreading Factor Pass 3.2(11) Dwell time Pass Interference prevention function Pass 3.3(1) Receiver Spurious Emission Pass Report No.: JR AD Page No. : 4 of 19 Report Version: Rev. 03

5 1 General Description 1.1 Information Product Details The following models are provided to this EUT. Model Name Product Name Description BT800 BTv4.0 Dual Mode USB HCI Module mounted with chipset antenna BT800-ST BTv4.0 Dual Mode USB HCI Module External Antenna variant connected to extenal antenna Specification of the Equipment under Test (EUT) Power Type Type(s) of Modulation / Technology Bluetooth Version V4.0 5Vdc from Host. Frequency Range (MHz) 2402 ~ 2480 MHz Total Channel Number 79 HW Version 1.0 SW Version FHSS / GFSK = 1Mbps, π/4dqpsk = 2Mbps, 8DPSK = 3Mbps A Accessories N/A Antenna Details Ant. No. Brand Model Type Connector Antenna Gain (dbi) Remark 1 ACX AT3216-B2R7HAA_3216 chip N/A 0.5 For BT800 2 ACX AT3216-B2R7HAA chip UFL 0.5 For BT800-ST Note: Please refer to Appendix B for more details about antenna pattern and other information Antenna Power Operating Mode Rated Power (mw/mhz) Measured Condcuted Power (mw/mhz) Radiated Power (mw/mhz) GFSK (non-afh) GFSK (AFH) DPSK (non-afh) DPSK (AFH) Report No.: JR AD Page No. : 5 of 19 Report Version: Rev. 03

6 1.1.6 Channel List Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Report No.: JR AD Page No. : 6 of 19 Report Version: Rev. 03

7 1.1.7 Test Tool and Power Setting Test Tool BlueTest3 version CSR Power Setting Channel Frequency (MHz) GFSK 8DPSK Protection Method for High Frequency and Modulation Section Protected Method Shielding Case Description RF and Modulation components are covered with shielding case and this shielding case is soldered. Photo Report No.: JR AD Page No. : 7 of 19 Report Version: Rev. 03

8 1.2 Test Equipment and Calibration Data Test Item Test Site RF Conducted (TH01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer R&S FSV Oct. 13, 2014 Oct. 12, 2015 Power Meter Anritsu ML2495A Sep. 29, 2014 Sep. 28, 2015 Power Sensor Anritsu MA2411B Sep. 29, 2014 Sep. 28, 2015 Signal Generator R&S SMB100A Oct. 08, 2014 Oct. 07, 2015 Measurement Software Measurement Software Sporton Sporton_ NA NA Agilent EN RF test NA NA Note 1: Calibration Interval of instruments listed above is one year. Note 2: Above instruments are calibrated by Electronics Testing Center 1.3 Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: ARIB STD-T66 Ver Measurement Uncertainty ISO/IEC requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Frequency error Bandwidth Conducted power TX Conducted emission RX Conducted emission Parameters Measurement Uncertainty Uncertainty ± Hz ± Hz ±0.537 db ±2.308 db ±2.525 db Report No.: JR AD Page No. : 8 of 19 Report Version: Rev. 03

9 2 Test Configuration 2.1 Testing Location and Conditions Test Site Site Category Ambient Condition Tested By TH01-WS OVEN Room 26 / 61% Allen Yu 2.2 Supporting Units Support Unit Brand Model FCC ID Notebook DELL E DC Power Supply GWINSTEK GPC The Worst Test Modes and Channel Details Test item Mode Test channel Antenna Power GFSK, 8DPSK 0 / 39 / 78 Frequency Tolerance Un-modulation 0 / 39 / 78 Transmitter Spurious Emission GFSK, 8DPSK 0 / 39 / 78 Occupied Bandwidth GFSK, 8DPSK 0 / 39 / 78 Spreading Bandwidth GFSK, 8DPSK 0 / 39 / 78 Spreading Factor GFSK, 8DPSK 0 / 39 / 78 Dwell time GFSK, 8DPSK 0 / 39 / 78 Receiver Spurious Emission GFSK, 8DPSK 0 / 39 / 78 Report No.: JR AD Page No. : 9 of 19 Report Version: Rev. 03

10 3 Transmitter Test Results 3.1 Antenna Power Limit of Antenna Power Mode Limit Tolerance 1) FH, FH+DS, FH+OFDM 3 mw / MHz 2) OFDM(Narrow- bandwidht), DS 10 mw / MHz 3) Other than 1) & 2) 10mW 4) OFDM (Wide-band) 5 mw / MHz +20 %, -80 % Test Procedures 1. Measure the total power by Power Meter in a state of hopping mode 2. Measure the burst ratio. Then calculate the real total power by burst ratio. 3. Calculate the mean power per 1MHz by dividing the total power by spread bandwidth 4. Output Power Density (mw/mhz) = Total Output Power (mw) / Burst Ratio / Spread Bandwidth (MHz) Test Setup Test Result of Maximum Transmit Power Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results 2. Antenna Power (Conducted Power) Report No.: JR AD Page No. : 10 of 19 Report Version: Rev. 03

11 3.2 Frequency Tolerance Limit of Frequency Tolerance Frequency tolerance shall be +/- 50ppm Test Procedures 1. Set Span = 150kHz, RBW = 1kHz, VBW = 30kHz, Sweep time = Auto, detector = Peak. 2. Use Peak search function to find the max peak value and record this value (RF). 3. Calculate frequency tolerance by below formula FT(ppm) = { (RF) (MF) / (MF) } (FT: Frequency Tolerance, RF: Reading Frequency, MF: Measurement Frequency.) Test Setup Test Result of Frequency Tolerance Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results Report No.: JR AD Page No. : 11 of 19 Report Version: Rev. 03

12 3.3 Occupied Bandwidth Limit of Occupied Bandwidth Mode Limit (MHz) FH 83.5 FH+DS 83.5 FH+OFDM 83.5 OFDM(Narrow- bandwidht), DS 26 Others 26 OFDM (Wide-band) Test Procedures 1. Set Span = 200MHz, RBW = VBW = 300kHz, detector = Peak, Sweep time = Auto. 2. Enable OBW function of spectrum analyzer to measure 99% bandwidth of total power Test Setup Test Result of Occupied Bandwidth Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results Report No.: JR AD Page No. : 12 of 19 Report Version: Rev. 03

13 3.4 Spreading Bandwidth and Factor Limit of Spreading Bandwidth and Factor Item Limit Spreading bandwidth 500kHz Spreading factor for DSSS (operates at 2400~ MHz) 5 Spreading factor for DSSS (operates at 2471~2497 MHz) Test Procedures 1. Set Span = 20MHz, RBW = VBW = 300kHz, detector = Peak, Sweep time = Auto. 2. Enable OBW (90%) function of spectrum analyzer to measure 90% bandwidth of total power Test Setup Test Result of Spreading Bandwidth and Factor Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results 8. Spread Factor Report No.: JR AD Page No. : 13 of 19 Report Version: Rev. 03

14 3.5 Transmitter Spurious Emissions Limit of Transmitter Spurious Emissions Item Tx Spurious Emission Limits 2.5 μw (2387MHz > f ; MHz < f ). 25 μw. (2387MHz f < 2400MHz) and (2483.5MHz < f MHz) Test Procedures 1. Set EUT to transmit at rated power and channel to perform test. 2. Set RBW = VBW = 1MHz, Detector type = Peak, Sweep time = Auto. 3. Following above setting of spectrum analyzer to measure spurious emission of 30~12750 MHz Test Setup Test Result of Transmitter Spurious Emissions Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results 5. Unwanted Emission Intensity Report No.: JR AD Page No. : 14 of 19 Report Version: Rev. 03

15 3.6 Dwell time Limit of Dwell time Limits Shall be less than 0.4 second Test Procedures 1. Set EUT to transmit at rated power and channel to perform test. 2. Set RBW = VBW = 300kHz, Detector type = Peak, Span = Zero Span, Sweep time = 5 msec. 3. Use marker function to measure Burst on and off time. 4. Burst ratio = On Time / ( On Time + Off time) Test Setup Test Result of Transmitter Spurious Emissions Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results 7. Hopping Frequency Dwell Time Report No.: JR AD Page No. : 15 of 19 Report Version: Rev. 03

16 3.7 Interference prevention function Limit of Interference Prevention Function Limits The identification code shall be 48 bits long Test Procedures 1. Set EUT under operating mode and link up with companion equipment 2. Check communication status between EUT and companion equipment is normal 3. Confirm the MAC address of EUT Test Setup Test Result of Interference Prevention Function Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results Report No.: JR AD Page No. : 16 of 19 Report Version: Rev. 03

17 4 Receiver Test Results 4.1 Receiver Spurious Emissions Limit of Receiver Spurious Emissions Item Rx Spurious Emission Limits 4nW (f < 1GHz). 20nW (1GHz f) Test Procedures 1. Set EUT to transmit at rated power and channel to perform test 2. Set RBW = VBW = 100kHz, detector = Peak, Sweep time = Auto for emission measurement below 1GHz. 3. Set RBW = VBW=1MHz, detector = Peak, Sweep time = Auto for emission measurement above 1GHz Test Setup Test Result of Receiver Spurious Emissions Reference Documents Appendix A 19-BT-F1D Test Items 1.Test Results 6. Limitation of Collateral Emission of Receiver Report No.: JR AD Page No. : 17 of 19 Report Version: Rev. 03

18 5 Photographs of the Test Configuration Report No.: JR AD Page No. : 18 of 19 Report Version: Rev. 03

19 6 Test laboratory information Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corp, it is our definitive objective is to institute long term, trust-based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan Hsiang. Location map can be found on our website Linkou Kwei Shan Kwei Shan Site II Tel: Tel: Tel: No. 30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, Taiwan, R.O.C. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. No. 14-1, Lane 19, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. If you have any suggestion, please feel free to contact us as below information Tel: Fax: ICC_Service@icertifi.com.tw END Report No.: JR AD Page No. : 19 of 19 Report Version: Rev. 03

20 International Certification Corp. Appendix A 19-BT-F1D 1. Test Results Test Voltage Testing for Electrical Specification V Normal Voltage ( 5V) MHz Measured Frequency MHz Frequency Error ppm Occupied Bandwidth Spread-spectrum Bandwidth MHz MHz μw Unwanted Emission Intensity 2 μw (Power emission within 1MHz 3 μw bandwidth) 4 μw μw Antenna Power (Measured Power) Antenna Power ( Rated Power) mw/mhz mw/mhz Antenna Power Error mw/mhz % Limitation of Collateral 6 nw Emission of Receiver 7 nw Hopping Frequency Dwell Time sec Radio Interference Prevention Function ID Code Good, MAC Address :00-16-A4-08-FE-2E Carrier Sense NR NR NR Remarks Low/Mid/High of test frequency range Limit 50 ppm Limit 83.5 MHz (RB/VB : 1MHz) Spread Factor Limit 5 (DSSS and FHSS) Limit 0.25 µw (-36 dbm) Limit 2.5 µw (-26 dbm) Limit 25 µw (-16 dbm) Limit 25 µw (-16 dbm) Limit 2.5 µw (-26 dbm) Limit 3 mw/mhz (4.77 dbm/mhz) Limit + 20% ~ - 80% Limit 4 nw (-54 dbm) Limit 20 nw (-47 dbm) Limit 0.4 sec (In 0.4 sec spreading rate) NR: Not Require 1: Frequency Band 1 (30 MHz f 1000 MHz) 5: Frequency Band 5 ( MHz f < 12.5 GHz) 2: Frequency Band 2 (1000 MHz < f 2387 MHz) 6: Frequency Band 6 (30 MHz f < 1000 MHz) 3: Frequency Band 3 (2387 MHz < f 2400 MHz) 7: Frequency Band 7 (1000 MHz f < 12.5 GHz) 4: Frequency Band 4 ( MHz f < MHz) 2. Antenna Power (Conducted Power) Test Voltage V Normal Voltage ( 5V) Remarks Testing for Electrical Specification Power Meter Raw from EUT Cable Loss Duty Cycle Factor MHz dbm db db 2402 ~ Refer to Calibration Result Duty Factor = 10 10Log 10(1/Duty Cycle) Spreading Bandwidth Factor Antenna Power (Conducted) Antenna Power (Conducted) Antenna Power Error db dbm/mhz mw/mhz mw % BW Factor = 10 10Log 10(1/Spreading BW) Limit 3 mw/mhz (4.77 dbm/mhz) Limit + 20% ~ - 80% Tranmsitter ON Time Tranmsitter (ON+OFF) Time Tranmsitter Duty Cycle (DH5) msec msec % % RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz Max TX on time mode 3. Transmission Radiation Angle Width (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) No. Antenna Power A Type Gain B Antenna 3dB Beam-width Horizontal 3dB Beam-width Vertical Model Length Loss C (dbm/mhz) (dbi) (Degree) (Degree) (m) (db) (dbi) (dbm/mhz) (Degree) Chip&PC Good B Cable Tatal Gain D=B-C EIRP F=A+D Permited Angle Judgement Remarks (Antenna Model) 4. Transmission Antenna Gain (EIRP Power) (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) Antenna (MHz) Output Level from Power Meter (Pt) (dbm) Cable Loss Between SG and Replacing Antenna (L) (db) Replacing Standard Antenna Gain (Gt) (dbi) EIRP Power Radiated Measurement EIRP = Pt L + Gt (dbm) Remarks (Antenna Model) 5. Unwanted Emission Intensity Unwanted Emission Intensity Test Voltage V MHz 1 MHz 2 MHz Unwanted Emission Frequency 3 MHz 4 MHz 5 MHz 1 db 2 db Cable Loss 3 db 4 db 5 db 1 dbm 2 dbm Spectrum Raw 3 dbm 4 dbm 5 dbm 1 dbm 2 dbm Unwanted Emission Intensity 3 dbm 4 dbm 5 dbm 1 μw 2 μw Unwanted Emission Intensity 3 μw 4 μw Normal Voltage ( 5V) Hopping Remarks RBW : 100 khz ; VBW : 100kHz RBW : 1 MHz ; VBW : 1 MHz Limit 0.25 µw (-36 dbm) Limit 2.5 µw (-26 dbm) Limit 25 µw (-16 dbm) Limit 25 µw (-16 dbm) Limit 2.5 µw (-26 dbm) Limit 0.25 µw (-36 dbm) Limit 2.5 µw (-26 dbm) Limit 25 µw (-16 dbm) Limit 25 µw (-16 dbm)

21 International Certification Corp. 5 μw Limit 2.5 µw (-26 dbm) 1: Frequency Band 1 (30 MHz f 1000 MHz) 5: Frequency Band 5 ( MHz f < 12.5 GHz) 2: Frequency Band 2 (1000 MHz < f 2387 MHz) 6: Frequency Band 6 (30 MHz f < 1000 MHz) 3: Frequency Band 3 (2387 MHz < f 2400 MHz) 7: Frequency Band 7 (1000 MHz f < 12.5 GHz) 4: Frequency Band 4 ( MHz f < MHz) 6. Limitation of Collateral Emission of Receiver Test Voltage V Normal Voltage ( 5V) Remarks MHz MHz st 30MHz~1000MHz:: Maximum emission and all emissions Spurious Emission 6 MHz nd beyond 1/10 of the limitation Frequency 6 MHz rd 7 MHz st must be indicated. 1000MHz~12.5GHz:: Maximum emission and all 7 MHz nd emissions beyond 1/10 of the 7 MHz rd limitation must be indicated. 6 db st Cable Loss 6 db nd 6 db rd 7 db st 7 db nd 7 db rd 6 dbm st Spectrum Raw 6 dbm nd 6 dbm rd 7 dbm st 7 dbm nd 7 dbm rd 6 dbm st Limit 4 nw (-54 dbm) Spurious Emission Intensity 6 dbm nd RBW : 100 khz ; VBW : dbm rd khz 7 dbm st Limit 20 nw (-47 dbm) 7 dbm 2nd RBW : 1 MHz ; VBW : 1 MHz 7 dbm 3rd 6 nw Total Emission Power 6 nw st Limit 4 nw (-54 dbm) 6 nw nd RBW : 100 khz ; VBW : 100 Spurious Emission Intensity 6 nw rd khz 7 nw Total Emission Power Limitation of Collateral Emission 7 nw st 7 nw 2nd 7 nw 3rd Limit 20 nw (-47 dbm) RBW : 1 MHz ; VBW : 1 MHz 1: Frequency Band 1 (30 MHz f 1000 MHz) 5: Frequency Band 5 ( MHz f < 12.5 GHz) 2: Frequency Band 2 (1000 MHz < f 2387 MHz) 6: Frequency Band 6 (30 MHz f < 1000 MHz) 3: Frequency Band 3 (2387 MHz < f 2400 MHz) 7: Frequency Band 7 (1000 MHz f < 12.5 GHz) 4: Frequency Band 4 ( MHz f < MHz) 7. Hopping Frequency Dwell Time Test Voltage DH5 V MHz Pulse Duration msec Measurement Time sec Dwell Time sec Spread Factor Test Voltage V MHz Normal Voltage ( 5V) 2402 ~ 2480 Spread Factor Spread-Spectrum Bandwidth Modulation Rate Spread Factor MHz Mcps Normal Voltage ( 5V) Remarks Limit 0.4 sec (In 0.4 sec spreading rate) RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz The total sum of holding time at arbitrary frequencies within the time multiplied 0.4 sec by the spreading rate Remarks Spread Factor Limit 5 (DSSS and FHSS)

22 International Certification Corp. Appendix A 19-BT-G1D 1. Test Results Test Voltage Measured Frequency Frequency Error Occupied Bandwidth Testing for Electrical Specification V MHz MHz ppm Spread-spectrum Bandwidth MHz μw Unwanted Emission Intensity 2 μw (Power emission within 1MHz 3 μw bandwidth) 4 μw μw Antenna Power (Measured Power) Antenna Power ( Rated Power) mw/mhz mw/mhz Antenna Power Error mw/mhz MHz % Normal Voltage ( 5V) Limitation of Collateral 5 nw Emission of Receiver 6 nw Hopping Frequency Dwell Time sec Radio Interference Prevention Function ID Code Good, MAC Address :00-16-A4-08-FE-2E Carrier Sense NR NR NR Remarks Low/Mid/High of test frequency range Limit 50 ppm Limit 83.5 MHz (RB/VB : 1MHz) Spread Factor Limit 5 (DSSS and FHSS) Limit 2.5 µw (-26 dbm) Limit 2.5 µw (-26 dbm) Limit 25 µw (-16 dbm) Limit 25 µw (-16 dbm) Limit 2.5 µw (-26 dbm) Limit 3 mw/mhz (4.77 dbm/mhz) Limit + 20% ~ - 80% Limit 4 nw (-54 dbm) Limit 20 nw (-47 dbm) Limit 0.4 sec (In 0.4 sec spreading rate) NR: Not Require 1: Frequency Band 1 (30 MHz f 1000 MHz) 5: Frequency Band 5 ( MHz f < 12.5 GHz) 2: Frequency Band 2 (1000 MHz < f 2387 MHz) 6: Frequency Band 6 (30 MHz f < 1000 MHz) 3: Frequency Band 3 (2387 MHz < f 2400 MHz) 7: Frequency Band 7 (1000 MHz f < 12.5 GHz) 4: Frequency Band 4 ( MHz f < MHz) 2. Antenna Power (Conducted Power) Test Voltage V Normal Voltage ( 5V) Remarks Testing for Electrical Specification MHz 2402 ~ 2480 Power Meter Raw from EUT dbm 4.54 Cable Loss Duty Cycle Factor db db Refer to Calibration Result Duty Factor = 10 10Log 10(1/Duty Cycle) Spreading Bandwidth Factor Antenna Power (Conducted) db dbm/mhz BW Factor = 10 10Log 10(1/Spreading BW) Limit 3 mw/mhz (4.77 dbm/mhz) Antenna Power (Conducted) Antenna Power Error mw/mhz mw % Limit + 20% ~ - 80% Tranmsitter ON Time Tranmsitter (ON+OFF) Time Tranmsitter Duty Cycle (3DH5) msec msec % % RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz Max TX on time mode 3. Transmission Radiation Angle Width (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) No. Antenna Power A Type Gain B Antenna 3dB Beam-width Horizontal 3dB Beam-width Vertical Cable Model Length Loss C Tatal Gain D=B-C EIRP F=A+D Permited Angle Judgement Remarks (Antenna Model) (dbm/mhz) (dbi) (Degree) (Degree) (m) (db) (dbi) (dbm/mhz) (Degree) Chip&PCB Good 4. Transmission Antenna Gain (EIRP Power) (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) Antenna Output Level from Power Meter (Pt) Cable Loss Between SG and Replacing Antenna (L) Replacing Standard Antenna Gain (Gt) EIRP Power Radiated Measurement EIRP = Pt L + Gt (MHz) (dbm) (db) (dbi) (dbm) Unwanted Emission Intensity Test Voltage V MHz Normal Voltage ( 5V) Hopping Remarks 1 MHz RBW : 100 khz ; VBW : 100kHz 2 MHz RBW : 1 MHz ; VBW : 1 MHz Unwanted Emission Frequency 3 MHz MHz MHz db db 1.49 Cable Loss 3 db db db dbm dbm Spectrum Raw 3 dbm dbm dbm dbm Limit 0.25 µw (-36 dbm) 2 dbm Limit 2.5 µw (-26 dbm) Unwanted Emission Intensity 3 dbm Limit 25 µw (-16 dbm) 4 dbm Limit 25 µw (-16 dbm) 5 dbm Limit 2.5 µw (-26 dbm) 1 μw Limit 0.25 µw (-36 dbm) 2 μw Limit 2.5 µw (-26 dbm) Unwanted Emission Intensity Remarks (Antenna Model)

23 International Certification Corp. Unwanted Emission Intensity 3 μw 4 μw 5 μw Limit 25 µw (-16 dbm) Limit 25 µw (-16 dbm) Limit 2.5 µw (-26 dbm) 1: Frequency Band 1 (30 MHz f 1000 MHz) 5: Frequency Band 5 ( MHz f < 12.5 GHz) 2: Frequency Band 2 (1000 MHz < f 2387 MHz) 6: Frequency Band 6 (30 MHz f < 1000 MHz) 3: Frequency Band 3 (2387 MHz < f 2400 MHz) 7: Frequency Band 7 (1000 MHz f < 12.5 GHz) 4: Frequency Band 4 ( MHz f < MHz) 6. Limitation of Collateral Emission of Receiver Test Voltage V Normal Voltage ( 5V) Remarks MHz MHz st 6 Spurious Emission Frequency MHz nd 6 MHz rd 7 MHz st 7 MHz nd 7 MHz rd 6 db st Cable Loss 6 db nd 6 db rd 7 db st 7 db nd 7 db rd 6 dbm st Spectrum Raw 6 dbm nd 6 dbm rd 7 dbm st 7 dbm nd 7 dbm rd 6 dbm st Spurious Emission Intensity 6 dbm nd 6 dbm rd 7 dbm st 7 dbm 2nd 7 dbm 3rd 6 nw Total Emission Power 6 nw st 6 nw nd Spurious Emission Intensity 6 nw rd 7 nw Total Emission Power Limitation of Collateral Emission 7 nw st 7 nw 2nd 7 nw 3rd 30MHz~1000MHz:: Maximum emission and all emissions beyond 1/10 of the limitation must be indicated. 1000MHz~12.5GHz:: Maximum emission and all emissions beyond 1/10 of the limitation must be indicated. Limit 4 nw (-54 dbm) RBW : 100 khz ; VBW : 100 khz Limit 20 nw (-47 dbm) RBW : 1 MHz ; VBW : 1 MHz Limit 4 nw (-54 dbm) RBW : 100 khz ; VBW : 100 khz Limit 20 nw (-47 dbm) RBW : 1 MHz ; VBW : 1 MHz 1: Frequency Band 1 (30 MHz f 1000 MHz) 5: Frequency Band 5 ( MHz f < 12.5 GHz) 2: Frequency Band 2 (1000 MHz < f 2387 MHz) 6: Frequency Band 6 (30 MHz f < 1000 MHz) 3: Frequency Band 3 (2387 MHz < f 2400 MHz) 7: Frequency Band 7 (1000 MHz f < 12.5 GHz) 4: Frequency Band 4 ( MHz f < MHz) 7. Hopping Frequency Dwell Time 3DH5 Test Voltage V Normal Voltage ( 5V) MHz Pulse Duration msec Measurement Time sec Dwell Time sec Spread Factor Test Voltage V Normal Voltage ( 5V) Spread Factor MHz 2402 ~ 2480 Spread-Spectrum Bandwidth Modulation Rate Mcps MHz Spread Factor Remarks Limit 0.4 sec (In 0.4 sec spreading rate) RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz The total sum of holding time at arbitrary frequencies within the time multiplied 0.4 sec by the spreading rate Remarks Spread Factor Limit 5 (DSSS and FHSS)

24 International Certification Corp. Appendix A 19-BT-F1D(AFH) 1. Test Results Testing for Electrical Specification Test Voltage V MHz 2402 Normal Voltage (5V ) Remarks Low/Mid/High of test frequency range Occupied Bandwidth Spread-spectrum Bandwidth Antenna Power (Measured Power) Antenna Power ( Rated Power) MHz MHz mw/mhz mw/mhz Limit 83.5 MHz (RB/VB : 1MHz) Spread Factor Limit 5 (DSSS and FHSS) Limit 3 mw/mhz (4.77 dbm/mhz) Antenna Power Error Hopping Frequency Dwell Time mw/mhz % sec Limit + 20% ~ - 80% Limit 0.4 sec (In 0.4 sec spreading rate) Radio Interference Prevention Function ID Code Good, MAC Address :00-16-A4-08-FE-2E Carrier Sense NR NR NR NR: Not Require 2. Antenna Power (Conducted Power) Test Voltage V Normal Voltage (5V ) Remarks Testing for Electrical Specification MHz 2402 ~ 2480 Power Meter Raw from EUT dbm 6.11 Cable Loss Duty Cycle Factor db db Refer to Calibration Result Duty Factor = 10 10Log 10(1/Duty Cycle) Spreading Bandwidth Factor Antenna Power (Conducted) db dbm/mhz BW Factor = 10 10Log 10(1/Spreading BW) Limit 3 mw/mhz (4.77 dbm/mhz) Antenna Power (Conducted) Antenna Power Error mw/mhz mw % 2.86 Limit + 20% ~ - 80% Tranmsitter ON Time Tranmsitter (ON+OFF) Time Tranmsitter Duty Cycle (DH5) msec msec % % RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz Max TX on time mode 3. Transmission Radiation Angle Width (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) No. Antenna Power A Type Gain B Antenna 3dB Beam-width Horizontal 3dB Beam-width Vertical Model Length Loss C (dbm/mhz) (dbi) (Degree) (Degree) (m) (db) (dbi) (dbm/mhz (Degree) Chip&PCB Good Cable Tatal Gain D=B-C EIRP F=A+D Permited Angle Judgement Remarks (Antenna Model) 4. Transmission Antenna Gain (EIRP Power) (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) Antenna Output Level from Power Meter (Pt) Cable Loss Between SG and Replacing Antenna (L) Replacing Standard Antenna Gain (Gt) (MHz) (dbm) (db) (dbi) Hopping Frequency Dwell Time Test Voltage V MHz 2402 Normal Voltage (5V ) Remarks Limit 0.4 sec (In 0.4 sec spreading rate) Pulse Duration msec RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz The total sum of holding time at arbitrary frequencies Measurement Time sec within the time multiplied 0.4 sec by the spreading Dwell Time sec rate 8. Spread Factor Test Voltage V MHz Normal Voltage (5V ) 2402 ~ 2480 Remarks Spread-Spectrum Bandwidth Modulation Rate MHz Mcps Spread Factor Spread Factor Limit 5 (DSSS and FHSS) DH5 Spread Factor EIRP Power Radiated Measurement EIRP = Pt L + Gt (dbm) Remarks (Antenna Model)

25 International Certification Corp. Appendix A 19-BT-G1D(AFH) 1. Test Results Testing for Electrical Specification Test Voltage V Normal Voltage ( 5V ) Remarks MHz Low/Mid/High of test frequency range Occupied Bandwidth Spread-spectrum Bandwidth Antenna Power (Measured Power) Antenna Power ( Rated Power) MHz MHz mw/mhz mw/mhz Limit 83.5 MHz (RB/VB : 1MHz) Spread Factor Limit 5 (DSSS and FHSS) Limit 3 mw/mhz (4.77 dbm/mhz) Antenna Power Error Hopping Frequency Dwell Time mw/mhz % sec Limit + 20% ~ - 80% Limit 0.4 sec (In 0.4 sec spreading rate) Radio Interference Prevention Function ID Code Good, MAC Address :00-16-A4-08-FE-2E NR: Not Require Carrier Sense NR NR NR 2. Antenna Power (Conducted Power) Test Voltage V Normal Voltage ( 5V ) Remarks Testing for Electrical Specification Power Meter Raw from EUT Cable Loss Duty Cycle Factor MHz dbm db db 2402 ~ Refer to Calibration Result Duty Factor = 10 10Log 10(1/Duty Cycle) Spreading Bandwidth Factor Antenna Power (Conducted) Antenna Power (Conducted) Antenna Power Error db dbm/mhz mw/mhz mw % BW Factor = 10 10Log 10(1/Spreading BW) Limit 3 mw/mhz (4.77 dbm/mhz) Limit + 20% ~ - 80% Tranmsitter ON Time Tranmsitter (ON+OFF) Time msec msec RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz Tranmsitter Duty Cycle (3DH5) % 79.31% Max TX on time mode 3. Transmission Radiation Angle Width (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) No. Antenna Power A Type Gain B Antenna 3dB Beam-width Horizontal 3dB Beam-width Vertical Model Length Loss C (dbm/mhz) (dbi) (Degree) (Degree) (m) (db) (dbi) (dbm/mhz) (Degree) Chip&PCB Good Cable Tatal Gain D=B-C EIRP F=A+D Permited Angle Judgement Remarks (Antenna Model) 4. Transmission Antenna Gain (EIRP Power) (This test item will not be applied to the EIRP power is lower than 6.91dBm/MHz) Replacing Standard Antenna Output Level from Power Meter Cable Loss Between SG and Replacing Antenna EIRP Power Radiated Measurement Gain (Pt) (L) EIRP = Pt L + Gt (Gt) (MHz) (dbm) (db) (dbi) (dbm) Hopping Frequency Dwell Time Test Voltage V MHz 2402 Normal Voltage ( 5V ) Remarks Limit 0.4 sec (In 0.4 sec spreading rate) Pulse Duration msec RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz The total sum of holding time at arbitrary Measurement Time sec frequencies within the time multiplied 0.4 sec by Dwell Time sec the spreading rate 8. Spread Factor Test Voltage V MHz Normal Voltage ( 5V ) 2402 ~ 2480 Remarks Spread-Spectrum Bandwidth Modulation Rate MHz Mcps Spread Factor Spread Factor Limit 5 (DSSS and FHSS) Antenna 3DH5 Spread Factor Remarks (Antenna Model) Appendix A - Page A6

26 International Ceritification Corp. Power Supply Voltage Fluctuation Test Voltage Fluctuation Test Normal Voltage High Voltage Low Voltage Input DC Power Output DC Power Voltage Variation(%) Note: Voltage Variation (%) = (Output High or Low Voltage - Output Normal Voltage)/Output Normal Voltage X 100 During the input supply voltage to the EUT from the external power source is varied by +/- 10%, if output voltage had been confirmed that the fluctuation of power supply to the RF circuit of EUT (excluding power source) is equal to or less than +/- 1%. Exempt extremely high and low supply voltage condition tests, EUT only operated in normal voltage to test all regulations.

27 International Certification Corp. Calibration Result 1. Linearity Check SG Output Spectrum Raw Power Meter Raw (dbm) (dbm) (dbm) Frequency Accuracy Confirmation Remark SG : 2450 MHz RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz ATT(30dB) ; Ref : 20 dbm SG : 5250 MHz RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz ATT(30dB) ; Ref : 20 dbm SG Output Spectrum Raw Freqquency Error (dbm) (MHz) (ppm) Remark SG Output : 0dBm RWB : 30 khz ; VBW : 30 khz : SP : 300kHz Limit 10% of frequency error limits 3. Cable Loss SG Output Power Meter Raw Power Meter Raw Cable Loss Without Cable With Cable (MHz) (dbm) (dbm) (db) SG Output : 0dBm Remark 4. Power Measurement System Loss (EUT Output to IF Output of Spectrum) SG Output Spectrum Raw Power Meter Raw System Path Loss With Cable form IF EUT to IF (MHz) (dbm) (dbm) (db) Remark SG : 0 dbm RBW : 1 MHz ; VBW : 1 MHz ; SP : 0Hz ATT(30dB) ; Ref : 20 dbm

28 Appendix B. Antenna Information

29 AT3216 Series Multilayer Chip Antenna ACX Advanced Ceramic X Features Monolithic SMD with small, low-profile and light-weight type. Wide bandwidth Applications Bluetooth/Wireless LAN/Home RF ISM band 2.4GHz applications Specifications Part Number Frequency Peak Gain Average Gain Range XZ-V XZ-V (MHz) VSWR Impedance AT3216 -B2R7HAA_ 2400 ~ dbi typ dbi typ. 2 max. 50 Ω Q ty/reel (pcs) : 3,000pcs Operating Temperature Range : -40 ~ +85 o C Storage Temperature Range : +5 ~ +35 o C, Humidity 45~75%RH Storage Period : 12 months max. Power Capacity : 2W max. Part Number AT B 2R7 HAA Type AT : Antenna Dimensions ( L W ) mm Material Code B Frequency Range 2R7=2700MHz Specification Code HAA Packaging Soldering =lead-containing /LF=lead-free T: Tape & Reel B: Bulk Terminal Configuration No. Terminal Name No. Terminal Name Feeding Point NC

30 ACX Advanced Ceramic X Dimensions and Recommended PC Board Pattern a Unit : mm W T L Mark L W T a Dimensions / (a) Without Matching Circuits (b) With Matching Circuits 1.2pF 3.3nH * 2.7nH *Line width should be designed to match 50Ω characteristic impedance, depending on PCB material and thickness.

31 Typical Electrical Characteristics (T=25 o C) Test Board ACX Advanced Ceramic X Ground 19mm 50Ω Feed Line 13.5mm Matching Circuit 6.5mm No Ground 39.5mm 4mm Antenna 6.5mm Return Loss (a) Without Matching Circuits (b) With Matching Circuits

32 Radiation Patterns ACX Advanced Ceramic X XY-V/XY-H Z XY Vertical Horizontal 180 X 90 o 270 o o Y 0 o XY-cut scanning direction XZ-V/XZ-H Y XZ Vertical Horizontal 180 o 90 o Z 0 o X 270 o XZ-cut scanning direction YZ-V/YZ-H X YZ Vertical Horizontal. 180 o 90 o Y 270 o Z 0 o YZ-cut scanning direction Advanced Ceramic X Corp. 16 Tzu Chiang Road, Hsinchu Industrial District Hsinchu Hsien 303, Taiwan TEL: FAX: acx@acxc.com.tw

33 AT3216 Series Multilayer Chip Antenna ACX Advanced Ceramic X Features Monolithic SMD with small, low-profile and light-weight type. Wide bandwidth RoHS compliant Applications Bluetooth/Wireless LAN/Home RF ISM band 2.4GHz applications Specifications Part Number Operating Peak Gain Average Gain Frequency (XZ-V) (XZ-V) (MHz) VSWR Impedance AT3216 -B2R7HAA_ 2400 ~ dbi typ dbi typ. 2 max. 50 Q ty/reel (pcs) : 3,000pcs Operating Temperature Range : -40 ~ +85 o C Storage Temperature Range : +5 ~ +35 o C, Humidity 45~75%RH Storage Period : 12 months max. Power Capacity : 2W max. Part Number AT B 2R7 HAA Type AT : Antenna Dimensions ( L W ) mm Material Code B Initial center frequency 2R7=2700MHz Specification Code HAA Packaging T: Tape & Reel B: Bulk Soldering /LF=lead-free Terminal Configuration No. Terminal Name No. Terminal Name Feeding Point NC AT3216-B2R7HAAT/LF REV:3 PAGE:1/

34 ACX Advanced Ceramic X Dimensions and Recommended PC Board Pattern a Unit : mm W T L Mark L W T a Dimensions 3.2± ± / ±0.3 (a) Without Matching Circuits (b) With Matching Circuits 1.2pF 3.3nH * 2.7nH *Line width should be designed to match 50 characteristic impedance, depending on PCB material and thickness. AT3216-B2R7HAAT/LF REV:3 PAGE:2/

35 ACX Advanced Ceramic X Typical Electrical Characteristics (T=25 o C) Test Board Ground 19mm 50 Feed Line 13.5mm Matching Circuit 6.5mm No Ground 39.5mm 4mm Antenna Return Loss (a) Without Matching Circuits 6.5mm (b) With Matching Circuits AT3216-B2R7HAAT/LF REV:3 PAGE:3/

36 ACX Advanced Ceramic X Radiation Patterns XY-V/XY-H Z XZ Vertical Horizontal 180 X 90 o 270 o o Y 0 o XY-cut scanning direction XZ-V/XZ-H Y YZ Vertical Horizontal 180 o X 90 o 270 o Z 0 o XZ-cut scanning direction YZ-V/YZ-H X XY Vertical Horizontal. 180 o 90 o Y 270 o Z 0 o YZ-cut scanning direction AT3216-B2R7HAAT/LF REV:3 PAGE:4/

37 ACX Advanced Ceramic X Taping Specifications Tape & Reel Dimensions (Unit: mm) vs. Quantity (pcs) A D 1.75 ± 0.1 C E F T EMBOSS TAPE B A Type A A B C D E F T Quantity/per reel Tape material AT ± ± ± ± ± ± ± ± 0.1 3,000pcs Plastic (Embossed) Reel Dimensions (Unit: mm) Label W4 W2 W3 Label: Customer s Name, ACX P/N, Q ty, Date, ±0.5 W5 ACX Corp. ±0.5 Type W2 W3 W4 W5 AT ±1 60±1 1.4±0.2 17±0.5 Leader and Trailer Tape Leader End Trailer End Trailer (160 mm min.) Empty Compartments with Cover Tape (500 mm min.) AT3216-B2R7HAAT/LF REV:3 PAGE:5/

38 ACX Advanced Ceramic X Peel-off Force Peeling Direction <10 0 Top Cover Tape Carrier Tape Peel-off force should be in the range of N at a peel-off speed of 300±10 mm/min. Storage Conditions (1) Temperature: 15 ~35, relative humidity (RH): 45~75%. (2) Non-corrosive environment Notes The contents of this data sheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. AT3216-B2R7HAAT/LF REV:3 PAGE:6/

39 ACX Advanced Ceramic X Mechanical & Environmental Characteristics Item Requirements Procedure 1. No apparent damage Solderability Soldering strength (Termination Adhesion) 2. More than 95% of the terminal 1. Preheat: o C electrode shall be covered with 2. Solder: o C for 5 1 sec new solder 1. Solder specimen onto test jig. 2. Apply push force at 0.5mm/s until electrode pads are 1. 1kg minimum peeled off or ceramic are broken. Pushing force is applied to longitude direction 1. Solder specimen onto test jig (FR4, 0.8mm) using the recommend soldering profile. 2. Apply a bending force of 2mm deflection Pressure Rod Deflection (Substrate Bending) 1. No apparent damage ` R230 90mm 1. Temperature: 85 2 o C 1. No apparent damage Heat/Humidity 2. Humidity: 90% ~ 95% RH 2. Fulfill the electrical specification Resistance 3. Duration: 1000±48hrs after test 4. Recovery: 1-2hrs 1. One cycle/step 1:125 ± 5 C for 30 min 1. No apparent damage Thermal shock step 2:- 40 ± 5 C for 30 min 2. Fulfill the electrical specification (Temperature Cycle) 2. No of cycles:100 after test 3. Recovery:1-2 hrs 1. No apparent damage 1. Temperature: -40 o 5 o C Low Temperature 2. Fulfill the electrical specification 2. Duration: 500 ±24hrs Resistance after test 3. Recovery: 1-2hrs AT3216-B2R7HAAT/LF REV:3 PAGE:7/

40 ACX Advanced Ceramic X Soldering Conditions Typical Soldering Profile for Lead-free Process Reflow Soldering : Temperature ( o C) 260 o C 217 o C o C 20s max. Pre-heating s. Time (s.) s Notes The contents of this data sheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. Advanced Ceramic X Corp. 16 Tzu Chiang Road, Hsinchu Industrial District Hsinchu Hsien 303, Taiwan TEL: FAX: acx@acxc.com.tw AT3216-B2R7HAAT/LF REV:3 PAGE:8/